Transcript
KONICA 2223 NOTES
COUNTS Total Count:P+1 Drum Count:P+7 [reset 47>91] PM Count:P+5 [reset 47>90] ----------------------ADJUSTMENTS After replacing drum and dev: [1] reset drum count 47>91Copy [2] run 47>copysize51Copy to reset dev count and adjust L detect. [3]reset pm count47>90CopyCopy [P5 to check pm count] [P7 to check drum count] ...................................................... Resets + Adjustments Drum count reset:mode47>91Copy P7 to check drum count *dev count automatically reset when you run L-detect [below] Dev setup + dev count reset: mode 47>copysize51copy to adjust L detect. copier will run and 51 will flash in copy quantity until done.[ also resets dev count] Pm count reset:47>90copy copy Lamp adjust(CVR):mode36>90>Copy>P: a # will flash in Print Quantity and display will show CVR Data. punch in a new # then: copy>P>[make test copy]> *to change setting again press P [new #]Copy P then test again cycle power when done. 55 is normal [higher#=lighter] ie:55P>copy: this will change value to 55 and make a copy. P will take
you back to value change screen. Lead edge REG:36>91 [-=more ] Lead vs tail ERASE move:36>92copyP(#)P c/s toggles +/[+=more lead/ less trail] [+20 or 30 seems good] lead to tail MAG:36>93copyP (-99 - +99)P front to rear MAG:36>95 Trail edge ERASE:36>96 [-=less] * 2223s have no lead edge erase when reducing or enlarging [no adjustment] ..................................................... Wire cleaning: use eraser or scrape down to gold coating with springhook. charge corona unit:35EA-9910 also try a small cloth and alchol on the end of springhook. Then 20 blank pages to dry wire. ----------------------------ERROR CODES F09:Leakage Detection:[exp. lamp/ fuser lamp/power supply/AC line short cct.] reset:25>P49P0copy F18:LCT motor fault:[upper limit switch/ lct lift motor] reset: cycle power F23:Toner Supply Abnormal:[Toner motor] reset: cycle power [to test motor, defeat front door and use 47-01 Start: to force add toner] *pop cover off toner hopper and vac it out....look for plastic or hardeded toner in augers at bottom of tank. *if copier is ticking, check cleaning unit auger. F26: toner density sensor: in dv tank: [dev tank empty or undertoned. reseat connector, or change sensor.
clean and reseat dev unit connector, clean big image unit connector] If that doesn’t help: run mode 47>copysize51copy to adjust L detect. copier will run and 51 will flash in copy quantity until done. also resets dev count reset: cycle power F27: ? Poor dev or drum unit connection F28:HVPS outputs abnormally high. [HVPS] reset: cycle power F34:Fusing Temp Too High:[middle or end thermistors] reset: see 35/36 F35/36:fuser too cool or lamp stays on too long. [paper above fuser/middle or end thermistors bad or unplugged /fuser lamp/main control board] reset:mode25 >P47P0copy>cycle power. F41:Optics return fault: F42:Optics forward fault: [main board/optics hp sensor/optics mot] reset: cycle power F43:CVR(lamp) fault:[main board/exp. lamp/power supply] reset: cycle power F45:lens drive fault:[lens hp sensor/lens mot] reset: cycle power F52:main motor fault:[main mot/main board/ power supply] reset: cycle power F53:Drum drive motor fault:[drum mot/main board/power supply] reset: cycle power F54:cooling fan fault:[cooling fan] reset: cycle power F60:ADF comm fault:[ADF board/wiring] reset: cycle power F67:Adf drive mot fault:[adf board/mot] reset: cycle power F70:sorter comm fault:[sorter board/wiring] F76:stapler motor fault:
F77:Sort bin drive fault: reset: cycle power F98:ADU drive fault: F88:AES fault:[AES board/exp lamp/power supply] reset: cycle power -----------------------------------ALARM CODES P11:wrong paper in main tray P12:wrong paper in aux tray P20:drum/dev unit out of place P24:drum at 24,500 [47>51] P24blink:drum at 25,000 [no copy][47>51] P25:replenishing toner P25blink:out of toner: [only if 25>92=0] P26:initilize dev unit[47>51] P27:A:when24/29 at same time[47>51] occurs when you replace dev + drum, even if you have not told copier that anyhing has been changed. B:if you have not changed drum and dev, then try cleaning the dev and drum unit connectors. note: sometimes just P29:dev at 25,000[47>51] P29blink:dev unit out of toner P51:front door open P64:lift RADF + remove original P81:aux switch/coin op is not on. P88:problem with auto exposure run mode47>98copy to adjust EE ----------------------------------PARTS Drum=947-124 Dev=947-226 Cb=25HA-2133 Hr=26AA53053 Pr=35EA53040 Fuser Cl roller=35EA53050 Claws[6]=26NA54270 Corona unit=35EA-2501 keyboard switches:534070140 ------------------------REMOTE SWITCH/ COINOP INFO
* before wiring, check that connector is positioned with the square "keys" to the left, so #s will be as shown below: Male connector pinout:{on remote cable} Pin4:x Pin1:red[switch] Pin5:white[counterP3] Pin2:black[switch] Pin6:green[counterP1] Pin3:x Female connector pinout:{on back of copier} Pin4:purple Pin1:red Pin5:orange Pin2:black Pin6:yellow Pin3:blue * if bypass switch does not work, try turning coinop mode off + on to reset. rem.sw/coinop enable:25>P05P0copy [cycle] rem.sw/coinop disable:25>P05P5copy[cycle] Key counter enable:25>P05P3copy[cycle] Message:remoteswitch:25>P30P5copy[cycle] coin op:25>P30P2copy[cycle] -------------------------COINOP INFO Service mode: on coinop bd, press YES and RESET, then release RESET.display will read Service, then Price 10C. Say YES to everthing until Done? Say NO, then say YES to all the next, then NO to Done? Timing should be 00, then YES until Done? Say YES to exit.To change a setting, say NO then YES to new setting. COINOP SETTINGS priceA: .10 priceB: .10 escrow: 5.00 DONE? [no] to continue 1copymin: no 1billmin: no cardreader: no val add: no alt add: no ok: no DONE? [no] to continue timing: 00
escrow t: 02 dual $ delay: 50 Done? [yes] to exit Counts: in Bypass mode, hold down P and C/S for 5 secs.Main and Cash counts will be shown in copier display. Problems: pull white tops off board connectors and press wires fully into Vgrooves.
