Ks101-bt A46001718 Installation Guide.indd

Transcript

KS101-BT Installation Guide Package Contents • One 10.1" Touch Panel PC • One sheet of Poron foam • One HDD drive bay kit • 1 DVD disk includes: - Manual DFI reserves the right to change the specifications at any time prior to the product's release. For the latest revision and more details of the installation procedure, please refer to the user's manual on the website. www.dfi.com 1 Panel COM 4/ 8-bit DIO COM 2 (RS232/RS422/RS485) USB 3.0 Antenna COM 1 (RS232/RS422/RS485) hole Power button Antenna hole Top View HDMI Reset/ Status LED COM 5 LAN 2 LAN 1 (RS232) Line-out Bottom View DC-in USB 2.0 Mic-in COM 3 (RS232/RS422/RS485) 2 Removing the Chassis Cover 1. Make sure the system and all other peripheral devices connected to it have been powered-off. 2. Disconnect all power cords and cables. 3. The 8 mounting screws on the rear side of the system are used to secure the cover to the chassis. Remove these screws and put them in a safe place for later use. Mounting screw Mounting screw Mounting screw 4. Lift the cover up to open the system. 5. The Mini PCIe and the micro SD slots are readily accessible after removing the chassis cover. 3 Installing a SATA Drive 1. The SATA data and power connectors are on the system board. SATA connectors SATA mounting location 2. Align the mounting holes of the SATA HDD with the mounting holes on the HDD drive bay and use the provided mounting screws to attach the SATA HDD to the drive bay. Mounting screw 4 3. Connect one end of the SATA cable to the SATA power and data connectors on the SATA drive and the other end of the SATA cable to the SATA power and data connectors on the system board. SATA drive SATA power/data cable 4. Align the mounting holes of the HDD drive bay with the mounting holes on the system and use the provided mounting screws to secure the drive bay in place. Mounting screw 5 Installing a Mini PCIe Card The system board is equipped with 3 Mini PCIe slots: two full-size and one half-size slots. Here we will demonstrate the installation of a full-size Mini PCIe card with SIM card slot for 4G connectivity. 1. Grasp the Mini PCIe card by its edges and align the notch in the connector of the PCIe card with the notch in the connector on the system board. 2. Push the Mini PCIe card down and use the provided mounting screws to secure the card on the system board. Mounting screw Note: The system also has one additional full-size Mini PCIe and one half-size Mini PCIe slot that use the mSATA and LPC interface respectively. 6 Mounting Options Wall mount The wall mount kit includes the following: • 2 wall mount brackets • Bracket screws Wall mount bracket 1 Wall mount bracket 2 1. Before starting any installation procedures, attach the poron foam to the Panel PC. Poron foam 2. Select a place on the wall where you will mount the Panel PC. 3. Use the provided mounting screws to attach “wall mount bracket 1” to the wall. Mounting screw Wall mount bracket 1 7 4. Attach the other bracket (wall mount bracket 2) to the rear of the Panel PC. Mounting screw Wall mount bracket 2 Hooks 5. Slide the Panel PC to "wall mount bracket 1" to attach the two brackets with the hooks. Then tighten the screw to secure the assembly in place. Screw 8 Panel mount The panel mounting kit includes the following: • 6 mounting clamps 1. Before starting any installation procedures, attach the poron foam to the Panel PC. Poron foam 2. Select a place on the panel (or wall) where you will mount the Panel PC. 3. Cut out a shape on the panel that corresponds to the Panel PC’s rear dimensions (272mm x 169mm) and ensure that the Panel PC can be fitted into the panel properly. 27 169 Mounting hole Panel 2 4. Insert the Panel PC from the outside surface of the panel into the mounting hole until it is properly fitted against the panel. 5. Position the mounting clamps along the rear edges of the Panel PC and insert them into the slits around the Panel PC. 9 White plastic cap Mounting clamp Slit for mounting the clamp 6. The first st and second clamps must be positioned and secured diagonally prior to mounting the rest of the clamps. Tighten the clamp’s screw using an electric screwdriver by pressing the white plastic cap onto the back of the panel. The illustration below shows that all clamps are properly mounted. Note: The maximum thickness of your panel’s mounting wall should be 10 mm for secure panel mount. 10 Board Layout and Jumper Settings COM 4 RS232/RS422/RS485 COM 2 RS232/RS422/RS485 DC-in LAN 2 (JP25) (JP2) (JP3) (JP4) (JP23) Mini PCIe with SIM 1 39 HDMI Power 40 LVDS LCD Panel 2 USB 0 USB 3.0 1 6 2 1 3 (JP4) 1 COM 5 9 Auto Power-on Select LCD/Inverter Power Select Backlight Enable Power Select Dimming Mode Select Panel Power Select 9 10 2 10 USB 2.0 USB 5 LAN 1 USB 7 USB 2 Power Select (JP6) 1 9 USB 5-7 Power Select (JP7) 10 COM 2 USB 0 System Fan Power 1 Select (JP5) 1 1 1 (JP25) 5 1 1 (JP2) (JP23) 1 (JP3) 6 1 USB 6 MicroSD (optional) iTE IT8528E Mini PCIe with LPC SATA 1 SATA Power 1 4 1 SATA 2.0 12 10 (JP21) 3 12 1 10 USB 2 mSATA eMMC (optional) (JP22, JP21) (JP18) (JP20) (JP17) COM 4/DIO Select Digital I/O 4-7 Output State Digital I/O 0-3 Output State Digital I/O Power Select (JP17) 1 USB 2.0 Line-out 1 Mic-in 4 1 SPI Flash BIOS Buzzer 1 DDR3L DDR3L DDR3L DDR3L (JP20) (JP18) 1 1 3 1 JP22 Clear CMOS Data (JP24) 1 Battery COM 3 RS232/RS422/RS485 Reset Chassis Intrusion COM 5 RS232 COM 1 RS232/RS422/RS485 USB Power Select: 0 (JP5), 1-2 (JP6), 5-7 (JP7) Auto Power-on Select JP25 +5V_standby (default) 1-2 On Power-on via power button (default) 1-2 On +5V 2-3 On Power-on via AC power 2-3 On Clear CMOS Data JP24 Normal (default) 1-2 On Clear CMOS Data 2-3 On Panel Power Select JP23 +12V 1-2 On Digital I/O Output State JP18 (DIO 4-7) JP20 (DIO 0-3) GND (default) 1-2 On +5V or +5V_standby 2-3 On Digital I/O Power Select JP17 +5V 3-4 On +5V_standby 1-2 On +3.3V (default) 5-6 On +5V (default) 2-3 On Backlight Enable Power Select JP3 +3.3V (default) 1-2 On +5V 2-3 On Dimming Mode Select JP4 Voltage Mode 1-2 On PWM Mode (default) 2-3 On LCD/Inverter Power Select JP2 +12V (default) 1-2 On +5V 2-3 On COM 4/DIO Select JP21, JP22 COM 4 (default) 1-2, 4-5 7-8, 10-11 On DIO 2-3, 5-6 8-9, 11-12 On Note: You cannot use COM 4 and DIO at the same time. Please set up JP21 and JP22 together. 11