Kubota Bx1800-2200 Mounting Kits 340

Transcript

Land Pride Assembly Instructions A separate Parts Manual for replacement parts can be purchased from your dealer or downloaded from our website at www.landpride.com. Have model and serial numbers handy when placing an order. Manual Part Numbers: BH1560 & BH1575 • 340-036M OPERATOR’S MANUAL BH1560/75 • 340-036P PARTS MANUAL BH1560/75 Kubota BX1800 - BX2200 Mounting Kit ! General Information These instructions apply to the Mounting Kit: 340-151A FRAME MOUNT & STAB KIT KUB BX BH1560/75 When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! On page 12 is a detailed listing of parts included in this kit. Use this list as a checklist to inventory parts received. Assembly Instructions Before You Start These assembly instructions contain only information on assembling the BH1560 & BH1575 mounting kit to the BX Series Kubota Tractor. A detailed Operator’s Manual was supplied with the main unit when it was purchased. For more specific information on safety concerns refer to the Operator’s Manual. Also included in the Operator’s Manual is important information on operation, adjustment, troubleshooting, and maintenance for this Backhoe (some of these sections do not apply to all options). B B The following Assembly will be more easily performed if the rear tires are removed and the rear of the tractor is safely supported. 1. Refer to Figure 1. Remove the three bolts (A) and lockwashers. These will be used to mount the brackets in the next step. Remove the three bolts and lockwashers (B). Discard bolts and keep the lockwashers. A B A Figure 1 © Copyright 2002 Printed 3/13/02 340-300M 1 Land Pride Assembly Instructions 2. Refer to Figure 2. Assemble Left Hand and Right Brackets as shown. Install bolts and lockwashers that were removed in Step 1 in locations labeled "B". Install supplied bolts and the lockwashers that were kept from Step 1 in locations labeled "A". 3. Mount rear tires on tractor and place tractor back on ground. A B B B A Mounting Bracket Figure 2 2 BH1560 & BH1575 Mounting Kit 340-300M 3/13/02 Land Pride Assembly Instructions 4. Refer to Figure 3. Remove the lower hitch brackets that are currently mounted to the backhoe. Assemble the brackets supplied in the mounting kit as shown. Mounting hardware is supplied with kit or hardware that was removed from brackets may be used. Lower Brackets Figure 3 3/13/02 BH1560 & BH1575 Mounting Kit 340-300M 3 Land Pride Assembly Instructions 5. Refer to Figure 4. Place Hydraulic Reservoir U-Bolts on Backhoe frame as shown (BH1560 only). For the BH1575, remove the front valve cover and mount the hydraulic tank in the same holes. U-Bolt U-Bolt Figure 4 4 BH1560 & BH1575 Mounting Kit 340-300M 3/13/02 Land Pride Assembly Instructions 6. Refer to Figure 5. Assemble Hydraulic Reservoir to the Backhoe using the U-Bolts placed in Step 4. (BH1560) Hydraulic Reservoir Figure 5 3/13/02 BH1560 & BH1575 Mounting Kit 340-300M 5 Land Pride Assembly Instructions 7. Assemble PTO Drive adapter to PTO pump as shown in Figure 6. PTO Drive Adapter PTO Pump Figure 6 8. Assemble the Suction Pump Adapter and Pressure Pump Adapter to the Pump as shown in Figure 7. Suction Pump Adapter Pressure Pump Adapter PTO Pump Figure 7 6 BH1560 & BH1575 Mounting Kit 340-300M 3/13/02 Land Pride Assembly Instructions 9. Install Filter Screen and Suction Hose Barb as shown in Figure 8 Filter Screen Hose Barb Figure 8 3/13/02 BH1560 & BH1575 Mounting Kit 340-300M 7 Land Pride Assembly Instructions 10. Assemble Suction Hose (Large Hose) end without fitting to Hydraulic Reservoir with Hose Clamp. Assemble the end with fitting to the Pump Suction Adapter. 11. Assemble Elbow Adapter to Hydraulic Reservoir making sure that elbow is pointing up. 12. Disconnect hose from inlet side of valve and connect to Elbow on Hydraulic Reservoir. 13. Disconnect Return Hose (Pressure) and connect to Pressure Adapter on Pump. Hose Clamp Inlet Hose Elbow Suction Hose Return (Pressure) Hose Figure 9 Suction Filter Inlet Valve of Backhoe Valve Tank Press. Pump Oil Reservoir (Backhoe or Tractor Sump) Return Hose From Backhoe Valve Figure 10 8 BH1560 & BH1575 Mounting Kit 340-300M 3/13/02 Land Pride Assembly Instructions 14. Assemble torque bar to Pump with 3/8" bolts and locknuts as shown. 15. Back tractor up to backhoe just close enough to assemble the Pump to tractor’s PTO drive shaft. Do not back completely up to backhoe. Leave some room for PTO pump and assembly. The Pump should be assembled so that the Torque Bar is pointing up. 16. Set lower 3-point arms 9" from ground to center of swivel ball, then back the tractor until lower 3-point align with lower mounting brackets on the backhoe then attach accordingly. Torque Bar PTO Pump 3/8" Bolts & Locknuts Figure 11 3/13/02 BH1560 & BH1575 Mounting Kit 340-300M 9 Land Pride Assembly Instructions 17. Align tractor’s lower 3-point arms and locking bar with the bottom holes of backhoe’s lower 3-point brackets. The locking bar will be beneath the lower 3-point arms. Install pins and secure with lynch pins. Align the locking bar’s eyebolts with the top holes of the Backhoes 3-point brackets. Install pins and secure with lock pins. There may be some adjustment of the eyebolts to align with the top holes. 3-Point Arms Above Locking Bar Adjustment Nuts Eyebolt Lock Pins Pins Locking Bar Figure 12 10 BH1560 & BH1575 Mounting Kit 340-300M 3/13/02 Land Pride Assembly Instructions Frame Stabilizer Bar Assembly 1. Place the Stabilizer Bar between the frame to make sure it will fit. The Stabilizer Bar end plates might need to be tweaked so that it fits between the frame as shown. 2. Assemble the two hole plate to the threaded hole of the Stabilizer Bar as shown capturing the frame between the Bar and the two hole plate. 3. Place the flat washer on the bolt and insert it through the top hole of two hole plate, through the hole in the tractor frame and through the top hole of the Stabilizer Bar. 4. Assemble the one hole plate to the other end of the Stabilizer Bar, capturing the tractor frame between the bar and the plate. Bolt, flat washer, lock washer and nut Bolt Two hole plate Stabilizer Bar One hole plate Figure 13 Disassembly 1. Lower bucket & stabilizers to the ground to get a sturdy base before any pin or pump removal. 2. Disconnect the Pump from the tractor’s PTO shaft. 3/13/02 3. Disassemble the locking bar completely. Top link and/ or stabilizer need to be unpinned before removing backhoe. 4. Drive away from Backhoe. BH1560 & BH1575 Mounting Kit 340-300M 11 Land Pride Listing of Parts 340-151A FRAME MOUNT & STAB. KIT KUB BX BH1560/75 Your Kit Includes: Qty. Part No. Part Description 1 340-053K 3 PT STABILIZER KIT BH1575 Qty. Part No. Part Description 5 2 5 839-526C 839-528C 839-529C 1/4" LINCH PIN BH STABILIZE ADJ.STABILIZER LINK CAT1 BH PIN,3/4X4 1/2 W/LOOP BH Qty. Part No. Part Description 1 340-293K FRME MNT KUB BX 1560 12 Qty. Part No. Part Description 1 1 1 1 1 1 1 8 2 8 8 2 13 3 1 2 2 6 3 2 2 1 1 1 340-022D 340-023D 340-303H 340-304H 340-305H 340-306H 340-306H 802-055C 802-184C 803-024C 804-019C 804-023C 804-076C 839-526C 839-529C 839-659C 839-828C 839-943C 839-944C 839-945C 839-946C 839-947C 839-948C 839-949C WASHER W/1 HOLE 3/8X3SQ. WASHER W/2 HOLE 3/8X2X3 3/4 FRAME MOUNT BRKT RH BX18/22 FRAME MOUNT BRKT LH BX18/22 CROSSTUBE WELDMT BX18/22 SPCL LWR LINK BRKT RH BX18/22 SPCL LWR LINK BRKT LH BX18/22 HHCS 5/8-11X2 GR5 HHCS 3/4-10X1 1/2 GR5 NUT LOCK 5/8-11 PLT WASHER FLAT 5/8 USS PLT WASHER LOCK SPRING 3/4 PLT WASHER LOCK 9/16 PLT 1/4" LINCH PIN BH STABILIZE PIN,3/4X4 1/2 W/LOOP BH PIN LOWER HITCH 7/8X3 1/ PIN HITCH 1X5 3/4 CAT II 25 CAPSCREW 14MMX1.5MMX50MM CAPSCREW 9/16-12X1 3/4 PIN CLEVIS 3/4X3 1/2 FITTING ADAPTOR C5205X6X6 HOSE 3/8X1/2MALEX9/16JICFX7 HOSE 3/8X1/2MALEX9/16JICFX6 NUT HEX 9/16-12 BH1560 & BH1575 Mounting Kit 340-300M 3/13/02