Kvm-301 / Kvm-d301 [ Operating Installation Manual ]

Transcript

KVM-301 / KVM-D301 [ Operating Installation Manual ] KC-D20 [OPTION] KC-C63 or KC-B61 [OPTION] KC-MB30 KVM-301 / KVM-D301 SINCE KOREA COMMUNICATIONS CO.,LTD 1976 http://www.kocom.com E-mail : [email protected] This manual is based on the date as shown in the right and specifications are subject to change without notice for quality improvement KVM-301 / KVM-D301 09.04 4" B/W Flat CRT Communication with door and door monitoring Door open during communication Intercom function between extended indoor units Surface mount type installation External 64 cut memory equipment (KVR-300) connection Connection with up to 2 door cameras, 2 monitors and 2 sub audio phone (KDP-602G) 5 melody selection KVR-300 [OPTION] Contents ■ Cautions for safety 4 ■ Monitor installation 8 ■ Door camera installation 9 ■ Precautions for operation 10 ■ Installation precautions 10 ■ Components 11 ■ Specifications 11 ■ Name of each part 12 ■ How to operate 13 Interlocked device 14 Wiring Diagram [Cable requirement] 16 Wiring Diagram [CCTV Camera A type] 19 Wiring Diagram [CCTV Camera B type] 20 Operational descriptions of special functions 21 KVR-300 User's manual 21 Installation (KVR-300) 22 How to operate (KVR-300) 22 ■ Warranty Card 23 4 5 6 7 Monitor Installation Door camera Installation Basic Installation method of Monitor 1 2 4X25mm Screw Door Camera Installation 3 Wall hanger pannel Rear KC-MB30 5 Camera front Camera front Screw (4X10mm) 6 Wrench Rear Screw (4X16mm) Wall 4X25mm Screw 4 KC-D20 Wall Wall Screw(4X10mm) Camera front Rear Bracket 4X8mm Screw 3X8mm Screw END KC-C63 / KC-B61 Name plate Camera Terminal Block Standard wire strip specification : 6~7mm Standard wire (AWG) : 16~24(0.5mm~1.2mm) baby support Upward support Screw(2.6X6mm) After fix the rear bracket with 4 screw, put the Door Camera into the grooves of rear bracket, and then fix it with hexagon screws and stick the finishing materials. Standard Height of Monitor Standard height of monitor is 1,450~1,500mm from bottom to the center of monitor screen. For installation, avoid the places where there is any excessive humidity, magnetic force, dangerous chemicals, diret ray of sun, and any places near a heater which can cause break down. Standard Height of Door Camera Surface mount Bottom base of One hall Box Center of monitor Bottom of 1 Rectangular switch box (unit:mm) Standard height of door camera is 1,400~1,450mm from the bottom of one camera to the floor. (unit:mm) 8 In case that the height of Door camera exceeds the range of min. 1,250mm ~ 1,550mm, it is impossible to control the screen picture with only the angle, and therefore, be careful of the height of camera in insrallation. 9 Precautions for Operation Component Door Camera DC 15V Adapter (DCtype) Keep away from humidifier and stove. High temperature and humidity can cause breakdown. Do not drop monitor or door camera, and avoid strong impact. Keep away from devices generating strong magnetic field (TV, Speaker, etc.) (Picture can be disturbed or blurred and breakdown can result) KC-MB30 Monitor 4X25mm 4ea Screws for fixing Monitor 4Px2 6P 1 Wall hanger bracket When cleaning, never use wet hands, volatile benzene or paint thinner. Keep picture clear by cleaning camera window frequently with soft cloths. ※ According to outside environment, you may view the images somewhat unclear. However, they do not result from any defect or trouble of the product. As this device consists of electronic precision components, and high voltage is generated internally, do not attempt to disassemble. Wall hanger bracket is packed in the Monitor 8P 2P KC-C63 or KC-B61 KC-D20 KC-C63 or KC-B61 Rear Bracket 4 Pin cable for camera 6 Pin cable for sub audio phone (KDP-602G) KC-MB30 8 Pin cable for monitor extension 2 Pin cable for Door Opener Wire 4X25mm 4ea "L" Wrench 4X8mm 1ea Screws for fixing Camera Specifications Installation Precautions MONITOR MODEL NO. KVM-301 Power Source Power Consumption Operating Temperature CRT Communication System Call Sound Wiring Mount Type Max.Wiring Distance Dimension Indoor Unit Connection Camera Connection SMPS AC 90-240V (50Hz/60Hz) DC15V ± 1V 1.2A Max: 20W, Standby 1.6W 0℃~ +40℃ 4" flat tube Duplex handset conversation Melody Sound 4 Wires (camera), 6Wires (audio phone), 8Wires (video phone) Surface mount TIV 0.8mm Cable=100m, UTP CAT5=100m 210 (W) x 222(H) x 57(D)mm KDP-602G (Audio phone), KVM-301 (B/W monitor) KC-MB30, KC-MB31,KC-D33, KC-D20, KC-MB20, KC-B61, KC-MB12, KC-MB14, KLP-302, KLP-304, KLP-306, KLP-308, KLP-312, KLP-P302, KLP-P304, KLP-P306, KLP-P308, KLP-P312 KC-MB30 KC-D20 KC-C63 / KC-B61 DC12V ± 1V (power from Monitor) Max: 3W (In Load) -10℃ ~ +50℃ 0.1Lux (LED ON) 110(W)x158(H) 96(W)x127(H) 95(W) x 127(H) x39(D)mm x32(D)mm x 34(D)mm Diagonal 120。 Diagonal 90 。 Diagonal 120 。 (angle adjustable) MODEL NO. Power Source Door Camera Power Consumption Operating Temperature Min. Illumination Dimension Angle of Lens 10 3X8mm 1ea KC-D20 KVM-D301 11 How to operate (Instruction for operating) Name of each part Power LED / Set button Setting of special functions SET button Extension button 4 inch screen Extended monitor or call & answer to extended monitor or doorphone To identify visitor Handset Communication with door camera When visitor presses the call button of door camera, the call from the door panel keeps ringing for 2 minutes. But monitor screen will be turned on for 1 minute. Monitor button won't fuction during the rest 1 minute. At this time, when holding the handset, the screen will be turned on and communication will be available. Camera button To communicate with door camera. Identification and communication with a visitor at door. Door Open button Door opening during communication While melody sounds from the monitor, the image of a visitor at door is displayed. Pick up the handset to communicate with a visitor at door. In case the handset is used with extended indoor units, press camera button for communication. Hang up the handset to finish communication. Communication with door is available for up to three minutes. 3-level melody volume control knob 3-level brightness control knob Camera monitoring-Don't need to hold handset Door Camera KC-MB30 1 KC-D20 KC-C63 / KC-B61 KC-MB30 KC-D20 2 3 2 4 4 5 5 1 6 ① ② ③ ④ ⑤ ⑥ ⑧ ①②③④ FG(FRAME GROUND) 1 2 4 5 6 12 KC-C63 / KC-B61 ⑦ C-Mic : To communicate with Monitor 3 LED Camera Lens Speaker: When visitor calls, the voice from monitor comes out of the speaker. Call Button: By pressing the button, the related house will be called. 7 Screw cap Name plate ① : VCC ② : GND ③ : Audio ④ : Video ⑤&⑥ : Door (Non-Polarity) ⑦ : Camera angle knob (Only KC-MB30) ⑧ : Wire clamp ①②③④ To view the state of door without communication, press camera button and view the image from door camera 1 through the screen. To view the image from door camera 2 through the screen, press camera button once more. To end door monitoring, press camera button once more. Door camera monitoring is available for up to one minute. 13 1 Camera : 1 Monotor Connection For this purpose, automatic DC doorlock should be installed on the door and connected to camera or monitor. OPTION OPTION If you press Door open button during the communication with door, the door is opened automatically. After opening the door, you may end the communication by hanging up the handset or pressing camera button. 4 WIRE Door Opener KVR-300 Extension Call & Communication When the device has an extended monitor or door-phone, pick up the handset and press Extension button. Then, tone ring sounds from the monitor. At this time, the device shifts to communication mode automatically. On the other hand, when an indoor call is received from the extended monitor or door-phone, pick up the handset. Then, communication is made available immediately. In the state of picking up the handset, press Extension button for communication. Indoor communication is available for up to three minutes. Name of Each Connection port Extended Interphone port Extended Memory Unit port ① +12V ② GND ③ CALL SIGNAL ④ VIDEO IN ⑤ VIDEO OUT ⑥ NC ⑦ PLAY SIGNAL ⑥ DOOR OPEN(-) ⑤ DOOR OPEN(+) ④ +12V 1 ③ I/P AUDIO ② GND ① DATA 2 Cameras : 1 Monitor Connection 4 WIRE 14 4 WIRE Door Opener Extended Memory Unit KVR-300 System configurations Doorphone KDP-602G 8 WIRE 6 1 7 2 WIRE Door Opener ④ VIDEO ③ AUDIO 1 ② GND ① VCC 2 8 Adapter 1 1 or For AC 90V~240V 4 1 For DC 6 WIRE 6 WIRE 4 WIRE External Power Input Camera 2 Extended monitor port DATA CA2 VIDEO CA2 AUDIO CA2 Vcc CA1 VIDEO CA1 AUDIO GND CA1 Vcc OPTION OPTION 4 WIRE 4 ⑧ ⑦ ⑥ ⑤ ④ ③ ② ① Doorphone KDP-602G Extended Memory Unit 2 WIRE Door Opener External Power Input Monitor 1 KVM-301 KVM-D301 Doorphone KDP-602G Monitor 2 KVM-301 KVM-D301 Doorphone KDP-602G Door Opener(DC) ② LINE 1 ① LINE 2 Camera 1 ④ ③ ② ① VIDEO AUDIO GND VCC 2 WIRE Door Opener 7 WIRE 7 WIRE External Power Input Extended Memory Unit KVR-300 Extended Memory Unit KVR-300 15 1 Camera : 1 Monitor Connection Wiring Full System Wiring / 2 Cameras : 2 Monitors Connection Wiring CAM 2 ① ② ③ ④ 6 ⑤ ⑥ 1 1 7 7 CAM 1 8 KDP-602G ※Option 1 Extended Memory Unit KVR-300 KC-MB30 1 4 ① ② ③ ④ ⑤ 1 4 1 CAM 1 ① : VCC ② : GND ③ : Audio ④ : Video ⑤&⑥ : Door (Non-Polarity) DC Power ⑥ 1 DC 15V Door opener FG AC POWER CABLE AC 90V-240V ※Option ※Option Adapter KC-MB30 ① ② ③ ④ ⑤ ① ② ③ ④ DC Power ⑥ KC-D20 6 ⑤ ⑥ 1 1 7 7 ※Option 8 KDP-602G ※Option 1 Extended Memory Unit KVR-300 Door opener FG 1 4 ①②③④ CAM 1 1 4 1 1 ※Option AC POWER CABLE AC 90V-240V 2 Cameras : 1 Monitor Connection Wiring CAM 2 DC 15V KC-MB30 ① ② ③ ④ ⑤ ① ② ③ ④ KC-D20 6 ⑤ ⑥ 1 1 Power 7 7 8 ※Option Extended Memory Unit KVR-300 Door opener FG ※Option KDP-602G 1 1 4 ①②③④ CAM 1 1 4 1 1 AC POWER CABLE AC 90V-240V ※Option DC 15V 16 DC ⑥ Extension Monitor ⑧ DATA ⑦ CAM2 VIDEO ⑥ CAM2 AUDIO ⑤ CAM2 Vcc ④ CAM1 VIDEO ③ CAM1 AUDIO ② GND ① CAM1 Vcc Adapter ① ② ③ ④ 6 1 1 7 7 8 1 4 1 4 1 1 Extended Memory Unit KVR-300 ※Option AC POWER CABLE AC 90V-240V DC 15V ⑤ ⑥ KDP-602G ※Option 2 1 DC Power Door opener ※Option Adapter Adapter 17 Wiring Diagram Wiring Diagram Wiring Diagram [Cable requirement] Wiring Diagram [CCTV Camera A type] Based on distance from a camera to the monitor ■ CAM1 Upto 100M : CAT5 cable A type CCTV KC-MB30 Orange W / Orange ① VCC double up G reen W / Green ② GND double up Blue W / Blue ③ Audio double up Brown W / Brown ④ Video double up ① ② ③ ④ ⑤ ⑥ DC Jack Video BNC FG ※ CAT5 wire configuration ※ In case of more than 50m of CAT5 cable length, the screen and voice quality can get lower. But the sympthom is not a kind of fault. So less than 50m is recommended. ■ Upto 50M : TIV 0.65㎟cable ■ Upto 100M : Over TIV 0.8㎟cable Main monitor ■ Upto 150M : TIV 0.8㎟cable + RG-59 / U RG-59 / U (Coaxial cable) for Video signal (Connect core to Video & shield to GND) A. In case the power consumtion of CCTV camera is below 200mA (DC12V) and in distance below 50M, you can use monitor power to CCTV camera. B. In case the power consumption of CCTV camera is over 200mA (DC 12V) and distance between CCTV camera and monitor is over 50M, the addional power supply shoud be used for CCTV camera. 18 19 Wiring Diagram Wiring Diagram [CCTV Camera B type] Door Camera Call Melody Selection (5 Melody) B type CAM1 CCTV ADAPTOR KC-MB30 ① ② ③ ④ ⑤ With hanging up the handset, select the camera 1 or camera2 using monitoring function. While screen is on, press Extension button for three seconds. Mode setting sound rings. Every time you press Extension button, saved bell sounds are output. Select the bell sound you want and press set button to change the bell sound of related door camera. With mode setting sound ringing, the changed bell sound is saved. Screen is automatically turned off. Extension Call Melody Selection (5 Melody) Video BNC Extension Extension button button set ⑥ FG CCTV Monitoring (3min) camera While screen is on, press set CCTV button for three seconds. External Memory Equipment (KVR-300) User's Manual Main monitor 20 21 Warranty For after-Sale service, have the following ready when you contact our branches. 1. Name of the product. 2. Model number of the product. 3. The area of problem. 4. Phone number and address at which you can be contacted. Warranty Card PRODUCT MODEL DATE PURCHASED WARRANTY PERIOD AGENCY ADDRESS KOCOM Warranties the original purchaser of this product as follows. Upto 64 cut frame record 22 1) This product is produced under strict quality control and inspection procedures. 2) If this product breaks down during proper use as a result of product defect, KOCOM will repair it within one year from date of purchase free of charge. 3) The following cases will be subject to charge, even during warranty period: a. Breakdown during transport, or through careless treatment, by consumer. b. Breakdown cause by unauthorized repair, or system modification. c. Breakdown caused by natural disaster or power disorder. 23