Kvm Cat.5 Extender Kit

Transcript

KVM Cat.5 Extender Kit KVM-9005 H/W Version: 3 LevelOne’s KVM-9005 Cat.5 KVM Extender allows you to locate PC, SERVER or KVM SWITCH up to 500feet /150m away from your controlling keyboard, mouse and VGA monitor using popular and inexpensive Ethernet cabling. The extender includes two devices, a “KVM-9005T transmitter “ to synthesize the keyboard/mouse/VGA monitor signal for easy long-distance transmission over popular Ethernet CAT.5 cable and a “KVM-9005R receiver“ to retrieve the synthetic signal back to keyboard/mouse/VGA monitor signal. sides. You just need to install a pair of transmitter and receiver into local and remote sides individually to provide you with the flexibility needed to control server groups either from a remote side (from the transmitter) or from a local site (from receiver). With its compact design, our Cat.5 Extender easily fits on a desk or any limited space. No software or interface card is required. You can easily active this device by simply connecting it to the power source (only required for receiver) and to the network cable, further saving cable layout and cable installation cost. The Cat.5 Extender uses the existing network construction to transfer console signals to remote 11 12 11 1 2 3 4 5 4 4 6 7 8 7 9 Key Features - Remote console up to 150m - Dual user access: at sender and receiver - Supports Cat. 5/6/7 - Superior high VGA resolution up to 1280 x 1024 - LEDs for power and data transfer - Receiver with knob for manual video signal tuning - Works with KVM Switches and single PC - No software necessary - Easily install in few minutes - Includes cable 0.9m (from PC or KVM switch to console) - Compatible with DOS, MS Windows, Linux, Unix and Netware  5 4 10 13 14 1. RJ45 Port 2. Dip Switch 3. VGA Console Port 4. PS/2 Console Port 5. VGA Console Port 6. PS/2 Console Port 7. PS/2 PC Port 8. VGA PC Port 9. RJ45 Port 10. Power Jack 11. PC1/PC2 LEDs 12. VGA Tuning 13. Power LED 14. Status LED Related Products ACC-1000 KVM Cat.5 Console Module KVM-9007 KVM Cat.5 Console Receiver www.level1.com I one world_one brand_one level_ KVM Switches/Consoles/Extenders  Technical Specifications KVM-9005T (Transmitter) PS/2 Keyboard port 1 PS/2 Mouse port 1 VGA port 1 Console port connector (all female type) KVM-9005R (Receiver) PS/2 Keyboard port 1 PS/2 Mouse port 1 VGA port 1 Console port connector (all female type) VGA blue HDDB 15 pin PC port connector (all female type) VGA blue HDDB 15 pin PC port connector (all female type) VGA blue HDDB 15 pin RJ-45 port connector 8P8C (same as Ethernet 100BASE-Tx port) LED Powr, Data Knobs (for VGA tuning) No Size 111.5(L) x 75(W) x 35.5(H) mm Power adapter From Keyboard Weight (g) 134g Temperature Operating: 0°C~50°C Humidity Operating: 0%~80%, Non-Condensing Certification FCC, CE VGA blue HDDB 15 pin RJ-45 port connector 8P8C (same as Ethernet 100BASE-Tx port) LED Powr, Data Knobs (for VGA tuning) 1 Size 111.5(L) x 75(W) x 35.5(H) mm Power adapter External Power, DC12/1A Weight (g) 120g Temperature Operating: 0°C~50°C Humidity Operating: 0%~80%, Non-Condensing Certification FCC, CE PS/2 purple mini-din 6 pin for keyboard PS/2 green mini-din 6 pin for mouse PS/2 purple mini-din 6 pin for keyboard PS/2 green mini-din 6 pin for mouse PS/2 purple mini-din 6 pin for keyboard PS/2 green mini-din 6 pin for mouse PS/2 purple mini-din 6 pin for keyboard PS/2 green mini-din 6 pin for mouse Product Diagram PC KVM-9005 Receiver KVM-9005 Transmitter PC 500 feet (150m) Cat.5/5e/6 Mouse Keyboard Extending your PC console up to 500 feet away Order Information KVM-9005: Cat.5 KVM Extender (incl. Cable) KVM-9005T: Cat.5 KVM Extender Transmitter KVM-9005R: Cat5 KVM Extender Receiver Package Contents KVM-9005 Transmitter + Receiver, Power Adapter, Console Cable, User Manual Mouse Keyboard All mentioned brand names are registered trademarks and property of their owners. Technical specifications are subject to change without notice. © Copyright Digital Data Communications GmbH. All Rights Reserved. V3.0 KVM-9005 KVM Cat5 Extender Model No: KVM-9005 ----1) KVM-9005T: Transmitter 2) KVM-9005R: Receiver Introduction: KVM Cat5 Extender is designed to control the PC, Server or KVM Switch up to 500 feet away from your Keyboard, Mouse and VGA monitor. KVM-9005T transmitter is to synthesize the signals of PS/2 keyboard, PS/2 mouse, and VGA monitor for being easily transmitted to a long distance over popular Ethernet CAT5 cable. KVM-9005R receiver is to take the synthetic signal and return it back to the signal s of PS/2 keyboard, PS/2 mouse and VGA monitor respectively. KVM-Cat5 is a good solution for those noisy server room environment where is unsuitable for people to work for a long time, besides, it facilitates effective management on dispersive computers through one dedicated central control room, demonstration room, meeting room, or at your desk. CAT5 STP cable (Shielded Twisted Pair)/ UTP cable (Unshielded Twisted Pair) or enhanced cable like CAT5E/CAT6 cable is applied to LAN network popularly. KVM-9005 uses the same existing network construction to transfer local console signal to remote side. KVM-9005 allows you to move your console, i.e. Keyboard, Mouse and VGA monitor, to a suitable place for centralized control conveniently over LAN network. You just need to install a pair of extender, the transmitter and receiver, into local side and remote side respectively. It also saves your cable layout and installation cost.
Distance up to 500 feet
Support standard 3-in-one KVM switch cable
Easy to install and friendly to set up the video signal via adjustable knobs.
Compatible with DOS, MS Windows, Linux, Unix, and Netware
No software required
High VGA resolution up to 1280 X 1024 (CAT5 cable up to 500 feet approximately)
LED indications for Power on/off and data transmission
Work with CAT5, CAT5e, or CAT6 Ethernet cable Before installation, please make sure to turn off all of peripherals and computers have; and follow the procedures to install your conditions correctly: Adjust the “KNOB“ on the top of KVM-9005R receiver for optimal VGA Technical specifications Functions KVM-9005T Transmitter KVM-9005R Receiver PS/2 Keyboard port 2 2 PS/2 Mouse port 2 2 VGA monitor port 2 2 display quality, which is various because of cable characteristic, such as the length, category, shielded, and unshielded. Turn on “DIP SWITCH 1 and 2” on the side of KVM-9005T, if the CAT5 cable is longer than 300 feet. The factory default value of “DIP SWITCH 1 and 2” is OFF. RJ-45 port 1 1 1. Console port connector (all female type) PS/2 purple mini-din 6 pin for keyboard PS/2 green mini-din 6 pin for mouse VGA blue HDDB 15 pin Extending your PC console up to 500 feet away: PC port connector or KVM PS/2 purple mini-din 6 pin for keyboard port switch console port connector PS/2 green mini-din 6 pin for mouse port (all female type) VGA blue HDDB 15 pin RJ-45 port connector 8P8C ( same as Ethernet 100BaseT port) LED Power, Data PC1,PC2 Knobs ( for VGA tuning ) No 1 300 feet segment DIP switch 1 No Size Desktop Desktop Power adapter No need DC9V, 500mA Weight (g) 134g 150g Dimension (mm) 111.5(L) x 75(W) x 35.5 (H) mm 117(L) x 80(W) x 39.5 (H) mm Package contents Model no.: KVM-9005 KVM-9005T transmitter KVM-9005R receiver KVM 3-in-one cable Power adapter DC9V,500mA 1 pc 1 pc 1 pc 1 pc Cable Diagram PS/2 Cable: Mini Din 6 pin Male to Male VGA Cable: HDDB15 pin Male to Male Features:
Compact desktop size
Work with single PC, as well as the console port and PC port of KVM Switch Installation: CAT5/5E/6 Straight Through STP (Shielded Twisted Pair) or UTP (Unshielded Twisted Pair) Cable: 8P8C 1.1. Connect PC console port with KVM–9005T transmitter “PC port” by using standard 3-in-one KVM switch cable (male to male). Normally, all of connectors are PC99 standard --- PS/2 purple mini-din 6 pin for keyboard, PS/2 green mini-din 6 pin for mouse and blue HDDB 15 pin for VGA. 1.2. Connect another PC console port with KVM-9005R receiver “PC port” by using standard 3-in-one KVM switch cable (male to male). 1.3. Connect CAT5 cable plug to RJ-45 connector of KVM-9005T transmitter. 1.4. Connect CAT5 cable plug to RJ-45 connector of KVM-9005R receiver. 1.5. Connect Keyboard, Mouse, and Monitor to KVM-9005T transmitter “console port.” 1.6. Connect Keyboard, Mouse, and Monitor to KVM-9005R receiver “console port.” 珪軟: 珪軟 + 2. = To select KVM-9005R + Receiver PC Port Extending console port or PC port of KVM Switch up to 500 feet away Scroll Lock + Scroll Lock + Q = Beeper (2)This device must accept any interference received. Including interference that may cause undesired operation. CE – Certificate This equipment is in compliance with the requirements of the following regulations: EN 55 022: CLASS B
When KVM-9005T transmitter is connected to a KVM Switch, the Hot Key Commands of the KVM switch will be transparent to be passed to KVM Switch. 2.1. Connect a KVM switch console port with KVM-9005T transmitter “PC port” by using standard 3-in-one KVM switch cable (male to male). Troubleshooting: 1. Receiver power LED is not ON. Make sure power adapter is connected to KVM-9005R receiver. 2. No video signal is displayed on the monitor. 2.2. Connect PC console port with KVM-9005R receiver “PC port” by using standard 3-in-one KVM switch cable (male to male). 2.1 Please check if VGA cable and CAT5 cable are properly 2.3. Connect CAT5 cable plug to RJ-45 connector of KVM-9005T transmitter. 2.2 Make sure VGA cable is attached to computer during the 2.4. Connect CAT5 cable plug to RJ-45 connector of KVM-9005R receiver. 2.3 Make sure power adapter is connected to receiver. 2.5. Connect Keyboard, Mouse, and Monitor to KVM-9005T transmitter “console port.” connected to the connectors respectively. boot-up process. 3. Video signal is foggy or un-cleared on the screen. 3.1 Please check if the VGA cable is properly connected. 3.2 Make sure the VGA resolution is not too high for the length of cable that is used. It is highly recommended to use “optimal 2.6. Connect Keyboard, Mouse, and Monitor to KVM-9005R receiver “console port.” 3. 4. CAT5 cable length” to get the best video quality and not to waste Power on PC and KVM-9005R receiver. unnecessary CAT5 cable. Therefore, if the problem happened, Check the VGA screen to make sure the quality is acceptable. If the video quality is not good for operation, please use knobs to adjust the please shorten the CAT5 cable length or reduce VGA resolution. video quality to optimization.
NOTE: High VGA resolution up to 1280X1024 (CAT5 cable length up to 500 feet approximately) 4. There is the error message “Keyboard or Mouse not found” on the screen. Please make sure PS/2 cable and connector are well seated. Keyboard Hot Key Commands: You can also conveniently command KVM-9005R receiver to switch its “PC port” and “RJ-45 port” through simple key sequences from the remote console side. To send commands to KVM-9005R receiver, press the “SCROLL LOCK” key twice within 2 seconds. There will be a beep for confirmation. apply USB-to-PS/2 adapter to KVM-9005. Made in Taiwan Certification: FCC KVM-9005_UM_V2.0 This equipment has been tested and found to comply with Part 15 of the Below are the different Hot Key Commands: Scroll Lock 5. For USB computers like PC, MAC, or SUN Microsystems, please Scroll Lock FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference C BMND24330A00 KVM-9005 KVM Cat5 Extender Model No: KVM-9005 ----1) KVM-9005T: Transmitter 2) KVM-9005R: Receiver Introduction: KVM Cat5 Extender is designed to control the PC, Server or KVM Switch up to 500 feet away from your Keyboard, Mouse and VGA monitor. KVM-9005T transmitter is to synthesize the signals of PS/2 keyboard, PS/2 mouse, and VGA monitor for being easily transmitted to a long distance over popular Ethernet CAT5 cable. KVM-9005R receiver is to take the synthetic signal and return it back to the signal s of PS/2 keyboard, PS/2 mouse and VGA monitor respectively. KVM-Cat5 is a good solution for those noisy server room environment where is unsuitable for people to work for a long time, besides, it facilitates effective management on dispersive computers through one dedicated central control room, demonstration room, meeting room, or at your desk. CAT5 STP cable (Shielded Twisted Pair)/ UTP cable (Unshielded Twisted Pair) or enhanced cable like CAT5E/CAT6 cable is applied to LAN network popularly. KVM-9005 uses the same existing network construction to transfer local console signal to remote side. KVM-9005 allows you to move your console, i.e. Keyboard, Mouse and VGA monitor, to a suitable place for centralized control conveniently over LAN network. You just need to install a pair of extender, the transmitter and receiver, into local side and remote side respectively. It also saves your cable layout and installation cost.
Distance up to 500 feet
Support standard 3-in-one KVM switch cable
Easy to install and friendly to set up the video signal via adjustable knobs.
Compatible with DOS, MS Windows, Linux, Unix, and Netware
No software required
High VGA resolution up to 1280 X 1024 (CAT5 cable up to 500 feet approximately)
LED indications for Power on/off and data transmission Technical specifications Functions KVM-9005T Transmitter KVM-9005R Receiver PS/2 Keyboard port 2 2 PS/2 Mouse port 2 2 VGA monitor port 2 2 the length, category, shielded, and unshielded. Turn on “DIP SWITCH 1 and 2” on the side of KVM-9005T, if the CAT5 cable is longer than 300 feet. The factory default value of “DIP SWITCH 1 and 2” is OFF. RJ-45 port 1 1 1. Console port connector (all female type) PS/2 purple mini-din 6 pin for keyboard PS/2 green mini-din 6 pin for mouse VGA blue HDDB 15 pin
Work with CAT5, CAT5e, or CAT6 Ethernet cable Extending your PC console up to 500 feet away: PC port connector or KVM PS/2 purple mini-din 6 pin for keyboard port switch console port connector PS/2 green mini-din 6 pin for mouse port (all female type) VGA blue HDDB 15 pin RJ-45 port connector 8P8C ( same as Ethernet 100BaseT port) LED Power, Data PC1,PC2 Knobs ( for VGA tuning ) No 1 300 feet segment DIP switch 1 No Size Desktop Desktop Power adapter No need DC9V, 500mA Weight (g) 134g 150g Dimension (mm) 111.5(L) x 75(W) x 35.5 (H) mm 117(L) x 80(W) x 39.5 (H) mm Package contents Model no.: KVM-9005 KVM-9005T transmitter KVM-9005R receiver KVM 3-in-one cable Power adapter DC9V,500mA 1 pc 1 pc 1 pc 1 pc Cable Diagram PS/2 Cable: Mini Din 6 pin Male to Male VGA Cable: HDDB15 pin Male to Male Features:
Compact desktop size
Work with single PC, as well as the console port and PC port of KVM Switch Installation: Before installation, please make sure to turn off all of peripherals and computers have; and follow the procedures to install your conditions correctly: Adjust the “KNOB“ on the top of KVM-9005R receiver for optimal VGA display quality, which is various because of cable characteristic, such as CAT5/5E/6 Straight Through STP (Shielded Twisted Pair) or UTP (Unshielded Twisted Pair) Cable: 8P8C 1.1. Connect PC console port with KVM–9005T transmitter “PC port” by using standard 3-in-one KVM switch cable (male to male). Normally, all of connectors are PC99 standard --- PS/2 purple mini-din 6 pin for keyboard, PS/2 green mini-din 6 pin for mouse and blue HDDB 15 pin for VGA. 1.2. Connect another PC console port with KVM-9005R receiver “PC port” by using standard 3-in-one KVM switch cable (male to male). 1.3. Connect CAT5 cable plug to RJ-45 connector of KVM-9005T transmitter. 1.4. Connect CAT5 cable plug to RJ-45 connector of KVM-9005R receiver. 1.5. Connect Keyboard, Mouse, and Monitor to KVM-9005T transmitter “console port.” 1.6. Connect Keyboard, Mouse, and Monitor to KVM-9005R receiver “console port.” 刪除: 刪除 + 2. = To select KVM-9005R + Receiver PC Port Extending console port or PC port of KVM Switch up to 500 feet away Scroll Lock + Scroll Lock + Q = Beeper (2)This device must accept any interference received. Including interference that may cause undesired operation. CE – Certificate This equipment is in compliance with the requirements of the following regulations: EN 55 022: CLASS B
When KVM-9005T transmitter is connected to a KVM Switch, the Hot Key Commands of the KVM switch will be transparent to be passed to KVM Switch. 2.1. Connect a KVM switch console port with KVM-9005T transmitter “PC port” by using standard 3-in-one KVM switch cable (male to male). Troubleshooting: 1. Receiver power LED is not ON. Make sure power adapter is connected to KVM-9005R receiver. 2. No video signal is displayed on the monitor. 2.2. Connect PC console port with KVM-9005R receiver “PC port” by using standard 3-in-one KVM switch cable (male to male). 2.1 Please check if VGA cable and CAT5 cable are properly 2.3. Connect CAT5 cable plug to RJ-45 connector of KVM-9005T transmitter. 2.2 Make sure VGA cable is attached to computer during the 2.4. Connect CAT5 cable plug to RJ-45 connector of KVM-9005R receiver. 2.3 Make sure power adapter is connected to receiver. 2.5. Connect Keyboard, Mouse, and Monitor to KVM-9005T transmitter “console port.” connected to the connectors respectively. boot-up process. 3. Video signal is foggy or un-cleared on the screen. 3.1 Please check if the VGA cable is properly connected. 3.2 Make sure the VGA resolution is not too high for the length of cable that is used. It is highly recommended to use “optimal 2.6. Connect Keyboard, Mouse, and Monitor to KVM-9005R receiver “console port.” 3. 4. CAT5 cable length” to get the best video quality and not to waste Power on PC and KVM-9005R receiver. unnecessary CAT5 cable. Therefore, if the problem happened, Check the VGA screen to make sure the quality is acceptable. If the video quality is not good for operation, please use knobs to adjust the please shorten the CAT5 cable length or reduce VGA resolution. video quality to optimization.
NOTE: High VGA resolution up to 1280X1024 (CAT5 cable length up to 500 feet approximately) 4. There is the error message “Keyboard or Mouse not found” on the screen. Please make sure PS/2 cable and connector are well seated. Keyboard Hot Key Commands: You can also conveniently command KVM-9005R receiver to switch its “PC port” and “RJ-45 port” through simple key sequences from the remote console side. To send commands to KVM-9005R receiver, press the “SCROLL LOCK” key twice within 2 seconds. There will be a beep for confirmation. apply USB-to-PS/2 adapter to KVM-9005. Made in Taiwan Certification: FCC V2.0 This equipment has been tested and found to comply with Part 15 of the Below are the different Hot Key Commands: Scroll Lock 5. For USB computers like PC, MAC, or SUN Microsystems, please Scroll Lock FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference C BMND24330A00