Transcript
LANCOM Systems GmbH Adenauerstr. 20/B2 52146 Würselen Germany E-Mail:
[email protected] Internet www.lancom.eu
. . . c o n n e c t i n g
y o u r
b u s i n e s s
LANCOM GS-1108
쮿
110641/1208
쮿
Handbuch Manual
110641_GS-1108_cover.indd 1
12.12.2008 12:20:31
LANCOM GS-1108
© 2008 LANCOM Systems GmbH, Wuerselen (Germany). All rights reserved. While the information in this manual has been compiled with great care, it may not be deemed an assurance of product characteristics. LANCOM Systems shall be liable only to the degree specified in the terms of sale and delivery. The reproduction and distribution of the documentation and software included with this product is subject to written permission by LANCOM Systems. We reserve the right to make any alterations that arise as the result of technical development. All explanations and documents for registration of the products you find in the appendix of this documentation, if they were present at the time of printing. Trademarks Windows®, Windows Vista™, Windows XP® and Microsoft® are registered trademarks of Microsoft, Corp. The LANCOM Systems logo, LCOS and the name LANCOM are registered trademarks of LANCOM Systems GmbH. All other names mentioned may be trademarks or registered trademarks of their respective owners. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit http://www.openssl.org/. This product includes cryptographic software written by Eric Young (
[email protected]). This product includes software developed by the NetBSD Foundation, Inc. and its contributors. This product includes the LZMA SDK written by Igor Pavlov. This product includes components available in source code as Open Source software with specific licenses and copyrights of various authors. In particular the firmware incorporates components which are subject to the GNU General Public License, version 2 (GPL). The license agreement including the text of the GPL can be found on the product CD in the product folder. The source codes and all license texts can be obtained from LANCOM Systems GmbH FTP server electronically upon request.
Subject to change without notice. No liability for technical errors or omissions. LANCOM Systems GmbH Adenauerstr. 20/B2 52146 Wuerselen Germany www.lancom.de Wuerselen, February 2009
110641/0209
LANCOM GS-1108 쮿 Chapter 1: Introduction
1 Introduction
1.1
EN
Optimally attuned to the LANCOM product portfolio, the LANCOM GS-1108 facilitates the structured cabling of small offices with up to eight networking devices. Each connection port can automatically recognize the data-transfer speed of networking equipment connected to it (10,100 or 1000 Mbit) as well as the PIN assignment of the network cable (auto MDI/X).
Package content Before beginning with the installation, please check that nothing is missing from your package. Along with the device itself, the box should contain the following accessories: LANCOM GS-1108 Power cord
✔
Printed documentation
✔
Rubber pads
✔
Should anything be missing, please take up immediate contact to your dealer or to the address on the delivery note supplied with your device.
3
LANCOM GS-1108 쮿 Chapter 2: Installation
2 Installation This section introduces your device. You will find an overview of all status displays and connectors here.
2.1
Status displays
EN
Status displays on the front of the device provide information about operational and connection status: ���
LANCOM GS-1108
��� Power
쐇
쐋
This LED provides information on the device's operating state. Off Green
��� Link/Act
Device switched off. On (permanently)
LAN connector status Off
��� 10/100/1000
Device operational.
No networking device attached
Green
On (permanently)
Networking device attached, no data traffic
Green
Flickering
Data traffic
Network connection status
Mbps Off
4
10-Mbit connection to networking device
Orange
On (permanently)
100-Mbit connection to networking device
Green
On (permanently)
1000-Mbit connection to networking device
LANCOM GS-1108 쮿 Chapter 2: Installation
2.2
Device connectors All connectors are located on the front or back panel:
LANCOM GS-1108
EN
���
쐇 쐃 10/100/1000Base-TX connectors 쐇 Connector for the supplied power cord
2.3
Hardware installation Installation of the LANCOM GS-1108 involves the following steps: 햲 LAN – by means of a suitable Ethernet cable, connect networking devices to an available LAN port 쐃 on the LANCOM GS-1108. The LAN ports are only suitable for connecting non-PoE-capable networking devices! Alternatively, PoE-capable networking devices which are connected to ports can be supplied with power via a PoE injector (e.g. LANCOM PoE Power Injector) located in between. The ports use autosensing to recognize the data rate (10/100/1000 Mbit) and the type (node/hub) of attached network devices. It is possible to connect devices of different speeds and types in parallel.
Use only network cables of category Cat 5 or better. For data transfer in full-duplex mode (100 or 1000 Mbit), the length of cable between the LANCOM GS-1108 and the connected networking device should not exceed 100 meters.
햳 Power supply – the socket 쐇 is for connecting the supplied power cord.
Use only the supplied power cord! The use of the wrong power cord can be of danger to the device or persons.
5
LANCOM GS-1108 쮿 Chapter 3: Appendix
3 Appendix 3.1
Performance and characteristics LANCOM GS-1108
Standards
Media
10BASE-T: UTP Cat. 3, 4, 5 or better
EN
100BASE-TX: UTP Cat. 5 or better 1000BASE-TX: UTP Cat. 5 or better IEEE
IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-TX
Operating modes
ANSI/IEEE
IEEE 802.3 Auto-negotiation
Switching
Store and forward
Auto MDI/MDI-X
Yes
Transfer mode
10/100Mbps, full/half-duplex (auto-sensing)
Transfer rate
10Mbps: 14880pps (64-byte packets)
1000Mbps, full duplex 100Mbps: 148800pps (64-byte packets) 1000Mbps: 1488000pps (64-byte packets) Flow control
IEEE 802.3x flow control for full-duplex Back pressure in half-duplex operation mode
Hardware
Approvals
Display
LEDs for Power, Link/Act, Speed
Power supply
100 - 240V, 50 - 60Hz, internal power supply unit
Environment
Temperature range 0-40°C; humidity 0-90 %; non-condensing
Housing
Metal housing, connections on the front; measures 197.2x 35.2 x 120 mm (W x H x D)
Power consumption (max.)
max. 10 Watt
Weight
1kg
Conformity
CE conform with DIN EN 55022 and DIN EN 55024 RoHS Compliance
Package content Item numbers
6
Cable
IEC cable
Manual
Printed Quick Installation Guide (DE/EN)
LANCOM GS-1108
61457
LANCOM GS-1108 쮿 Chapter 3: Appendix
CE-declarations of conformity The CE declarations of conformity for LANCOM routers can be found in the download area of the LANCOM web site (www.lancom-systems.com).
EN
3.2
7
