Laser Distance Finder/ Measuring Tool

Transcript

INSTRUCTION MANUAL LASER DISTANCE FINDER/ MEASURING TOOL 057-4585-0 If any parts are missing or damaged, or if you have any questions, please call our toll-free helpline at 1-800-689-9928. Read and understand this instruction manual thoroughly before using the product. It contains important information for your safety as well as operating and maintenance advice. Keep this instruction manual for future use. Should this product be passed on to a third party, then this instruction manual must be included. LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 TECHNICAL SPECIFICATIONS 3–4 SAFETY GUIDELINES 5–7 DESCRIPTION 8 OPERATING INSTRUCTIONS 9–18 MAINTENANCE 19 TROUBLESHOOTING 20 PARTS LIST 21–22 WARRANTY 23–24 LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 TABLE OF CONTENTS 2 TECHNICAL SPECIFICATIONS RECOMMENDED USE Indoors STORAGE TEMPERATURE -20 ºC to 60ºC (-4 to 140°F) POWER SUPPLY 6V (4 x 1.5 V AAA alkaline batteries) SIZE 113 x 56.4 x 35 (mm) TYPICAL MEASURING RANGE 0.1–50 m* TYPICAL MEASURING ACCURACY ±3 mm* WEIGHT (WITHOUT BATTERIES) 0.34 lb. (155 g) *Important: Under unfavorable conditions, such as in bright sunlight or when measuring poorly reflecting or very rough surfaces, the tool’s measuring range and accuracy will be reduced. In such circumstances, please use a reflector (available separately) when taking measurements. The reflector is a target to be used with the Laser Distance Finder/Measuring Tool to increase the intensity of the reflected light. SMALLEST UNIT DISPLAYED 1mm LASER CLASS II LASER TYPE λ=635 nm, P≤ 1 mW AUTOMATIC SWITCH OFF Laser: 20 seconds Measuring tool: 5 minutes ESTIMATED BATTERY LIFE Up to 5,000 single (ALKALINE AAA BATTERIES) measurements OPTIMUM OPERATING TEMPERATURE -10 ºC to 50ºC (14° to 122°F) LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 TECHNICAL SPECIFICATIONS 4 3 SAFETY GUIDELINES WARNING! CAUTION! Safety symbols in this Instruction Manual are used to flag possible dangers. The safety symbols and their explanations require your full understanding. The safety warnings do not, by themselves, eliminate any danger, nor are they substitutes for proper accident prevention measures. Do not attempt to modify the performance of the laser device in any way. This may result in a dangerous exposure to laser radiation. WARNING! This Safety Alert Symbol indicates caution, warning, or danger. Failure to obey a safety warning can result in serious injury to yourself or others. To reduce the risk of injury, fire, or electric shock, always follow the safety precautions. Become familiar with the Laser distance finder/measuring tool Before using this Laser Distance Finder/Measuring Tool, read this Instruction Manual carefully. Keep this Manual in a safe place for future reference. Important This device should only be serviced by a qualified service technician. For more information, call the toll-free helpline at 1-800-689-9928. Read all instructions thoroughly Save these instructions CAUTION! Do not attempt to use this laser distance finder/measuring tool until you have read all instructions, safety rules, and warnings carefully and thoroughly. Keep this Instruction Manual and review it frequently for reference. WARNING! Be sure to read and understand all instructions in this manual before using this product. Failure to follow all instructions may result in hazardous radiation exposure. WARNING! Laser radiation. Do not stare into the beam. Turn the laser beam on only when using this tool. LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 WARNING! Use of controls, adjustments, or the performance of procedures other than those specified in this manual may result in hazardous radiation exposure. WARNING! The use of optical instruments, such as, but not limited to, telescopes or transits to view the laser beam will increase eye hazard. This laser distance finder/measuring tool has a built-in laser light. The laser is a Class II and emits output power of a maximum 1 mW and 620-690 nm wavelengths. These lasers do not normally present an optical hazard. However, do not stare at the beam, as this can cause flash blindness. The following label is on your laser distance finder/ LASER DISTANCE 057-4585-0 FINDER / MEASURING TOOL measuring tool. It indicates the location from which OUTIL À MESURER – TÉLÉMÈTRE À LASER the laser distance finder/measuring tool emits 6V 4×1.5 V AAA Battery / 6V 4 piles AAA de 1,5V the laser light. Be aware of the laser light location ATTENTION CAUTION LASER RADIATION RAYONNEMENT LASER : NE REGARDEZ when using the tool. Always make sure that any by DO NOT STARE INTO BEAM PAS DIRECTEMENT LE FAISCEAU. 635nm, P≤1mW 635nm, Puissance≤1mW standers in the vicinity of use are made aware of the Class II laser product Produit laser de classe II Complies with 21 CFR parts Conforme au règlement 21 CFR 1040.10 and 1040.11 sections 1040.10 et 1040.11 dangers of looking directly into the laser. MADE IN CHINA/FABRIQUÉ EN CHINE IMPORTED BY/IMPORTÉ PAR MASTERCRAFT CANADA TORONTO, CANADA M4S 2B8 DATE CODE: CODE DE DATE : • Do not remove or deface any product labels. • Avoid direct eye exposure. The laser beam can cause flash blindness. • The laser tool is not a toy. Always keep it out of the reach of children. The laser light emitted from this device should never be directed toward any person for any reason. • Do not operate the tool around children or allow children to operate the tool. • Do not place the tool in a position that may cause anyone to stare at the laser beam, whether intentionally or unintentionally. • Do not use on surfaces such as sheet steel that have shiny, reflective surfaces. The reflective surface could reflect the beam back at the operator. • Always turn the laser tool off when not in use. Leaving the tool on increases the risk of someone inadvertently staring into the laser beam. LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 SAFETY GUIDELINES 6 5 8 • Do not attempt to modify the performance of this laser device in any way. This may result in a dangerous exposure to laser radiation. • Do not attempt to repair or disassemble the laser distance finder/measuring tool. If unqualified persons attempt to repair this product, serious injury may occur. Any repair required on this laser product should be performed only by qualified service personnel. • Do not operate the tool in combustible areas, such as in the presence of flammable liquids, gases, or dust. • Use of other accessories that have been designed for use with other laser tools could result in serious injury. • Keep batteries out of reach of children. • Do not direct the laser distance finder/measuring tool towards the sun or other sources of bright light. This may cause an Error reading or inaccurate measurements. • Do not use the laser distance finder/measuring tool as a leveling tool. • Do not operate the laser tool in wet, dusty, sandy, or other adverse environments. Such conditions may damage inner components and affect measuring accuracy. • When the laser distance finder/measuring tool is brought into a warm environment from very cold conditions, or vice versa, allow it to come to the surrounding temperature before use. • Measuring errors can occur when measuring toward colorless liquids (e.g., water), clean glass, Styrofoam, or similar translucent or low-density materials. • High-gloss surfaces will deflect the laser beam and result in Error measurements. • Very bright surroundings combined with a very low reflecting surface will reduce the measuring range and accuracy. • Do not immerse the tool in water. Wipe off dirt with a damp, soft cloth. Do not use aggressive cleaning agents or solutions. Treat the optical surfaces with the same care that you would apply to eye glasses or cameras. • The accuracy of the tool must be checked before use after it has been dropped or subjected to other mechanical stresses. LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 Know your laser distance finder/measuring tool 5 1 4 2 3 6 7 No. Description No. Description 1 5 LCD display Battery compartment 2 Keyboard 6 Laser-receiving lens 3 Positioning pin 7 4 1/4" tripod screw Laser-exit aperture LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 DESCRIPTION SAFETY GUIDELINES 7 10 Become familiar with the laser distance finder/measuring tool. Before attempting to use this laser distance finder/measuring tool, become familiar with all of its operating features and safety requirements. LCD display Large LCD screen with white backlighting helps makes it easy to read the large numeral measuring data clearly, even in dark conditions. Full battery indicator Empty battery indicator Indicates that the measurement is taken from the positioning pin Indicates that the measurement is taken from the bottom of the tool Indicates that the measurement is taken from the position of the tripod screw Indicates that the measurement is taken from the front of the tool Laser beam indicator Single-distance measurement Area measurement Volume measurement Single Pythagorean Theorem measurement Keyboard function (fig 1) fig 1 For operation, please see the references to the specific functions and computations later in this manual. 3 2 1 1. Power key - Turns on/off the tool. 2. Measure key - Turns on the laser and 5 4 takes measurements; activates the 6 continuous measurement. 8 7 3. Clear key - Clears the measurements; reverts to single-distance measurement mode. 4. Mode key - Changes the measuring mode among: area, volume, single Pythagorean Theorem, double Pythagorean Theorem, and single-distance measurement modes. 5. Plus/Minus key - For addition or subtraction of measurements. 6. Measuring reference point - Switches the measuring reference among: the rear of the tool, the position of the tripod screw, the front of the tool, and the positioning pin. 7. Unit conversion key 8. Max/Min key - Activates the maximum or minimum measuring mode. To install batteries (fig 2) This laser distance finder/measuring tool uses four “AAA” batteries. 1. Push the hook to open the battery cover. 2. Insert four new “AAA” alkaline batteries according to the polarity indicators in the battery compartment. Be sure the polarity (+/-) is correct! 3. Close the cover and lock it securely in place. fig 2 Double Pythagorean Theorem measurement Minimum measurement indicator Maximum measurement indicator Continuous measurement indicator LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS 9 12 NOTE: • Replace the batteries when the battery indicator shows empty. • Remove the batteries from the laser distance finder/measuring tool when not using it for extended periods. • The 4 AAA batteries should match each other in brand and type. • Do not mix old and new batteries. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable batteries. • Remove dead batteries immediately and dispose of them according to your local ordinance. Never dispose of batteries in fire. To change the units key to change the units among the choices listed below. Press the DISTANCE AREA 0.000 m 0.000 m 0.000 m3 0 mm 0.000 m 0.000 m3 0.000 ft 0.000 ft 0.000 ft3 Turning the laser distance finder/measuring tool on and off 0' 00" 2 0.000 ft 0.000 ft3 to turn on the tool. 0.0 In 0.000 ft2 0.000 ft3 0 In 1/16 0.000 ft2 0.000 ft3 1. Press the power key 2. The tool will automatically self-calibrate. During this process, the laser will turn on briefly. WARNING! Do not point the laser dot at persons or animals and do not stare into the laser beam or view it directly with optical instruments. 3. The tool will default to the single-distance measuring mode, indicating that the tool is ready to take measurements. for about 2 seconds to turn off the tool. 4. Press the power key 5. When the laser distance finder/measuring tool is inactive for 5 minutes, it will automatically turn off to save battery power. To change measuring reference point The default reference setting is from the rear of the tool. Press the measuring reference point . Each time the key is pressed, the reference point will change: the rear of the tool, key the position of the tripod screw, the front of the tool or the positioning pin location; the next measurement will be taken from the position you set. After powering off, the reference point will automatically default back to rear of the tool. Clear function Push the clear key to erase the current measurement and display the previous measurement. While making area, volume or indirect measurements, each single measurement can be deleted and re-measured in series. Continuously press the key to go back to single-distance measurement mode. LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 VOLUME 2 2 2 1/16 To start the measurement WARNING! Do not point the laser dot at persons or animals and do not stare into the laser beam or view it directly with optical instruments. NOTE: The laser will switch off after 20 seconds of inactivity. If a measurement has not been again to turn on the laser. made within the previous 20 seconds, push measure key Single distance measurement 1. Press the mode key to choose the single-distance measurement mode. The mode icon will blink on the LCD. to turn on the laser beam. Aim the laser at the target to which you 2. Press the measure key want to measure. again to take a measurement. The result is displayed immediately 3. Press the measure key on the LCD. NOTE: After choosing Area, Volume or Pythagorean Theorem measurement modes, press the to switch back to single-measurement mode. clear key LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS 11 OPERATING INSTRUCTIONS Area measurement Single pythagorean theorem measurement mode 1. Press the mode key to choose the area-measurement mode; the mode icon will blink on the LCD screen. to turn on the laser beam; position the tool to aim the laser dot at 2. Press the measure key the target to which you want to measure. to take the first length measurement (e.g. length), press the 3. Press the measure key again to take the second length measurement (e.g. width). The area is measure key displayed immediately on the LCD. The Pythagorean Theorem measurement mode is used to measure distances that cannot be measured directly because an obstacle would obstruct the laser beam or because no target surface is available as a reflector. Correct results are achieved only when the laser beam and the distance to be determined form a precise right angle (90°). Volume measurement For this purpose, AB and AC must be measured. The lines labeled AC and BC must ? form a right angle. to choose 1. Press the mode key the single Pythagorean Theorem A measurement mode. The mode icon C will blink on the LCD. to turn on the laser beam; position the tool to aim the laser at the 2. Press the measure key target B. to display the measured length of AB in the first row of the 3. Press the measure key screen. 4. Without changing the location of the measuring reference point on the tool in position A, aim the laser dot perpendicularly at the target C. again to display the calculated length of BC in the lowest row of 5. Press the measure key the screen; the distance AC will be displayed at the same time in the second row. 1. Press the mode key to choose the volume measurement mode; the mode icon will blink on the LCD screen. to turn on the laser beam; position the tool to aim the laser dot at 2. Press the measure key the target to which you want to measure. to take the first length measurement (e.g. length), press the 3. Press the measure key to take the second length measurement (e.g. width), press the measure key measure key to take the third length measurement (e.g. height). The volume is displayed immediately on the LCD. In the illustrated example (see fig 3), the length BC is the unknown distance to be determined. fig 3 B NOTE: • The distance AC must be shorter than the hypotenuse AB; otherwise the LCD will display “Err 008” to remind you to re-measure the distance AC. • When taking the two measurements, make sure that they are taken from the same starting point (A) and that the second measurement is perpendicular to the target C. Taking the measurements correctly will result in the most accurate calculated distance. LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 OPERATING INSTRUCTIONS 14 13 OPERATING INSTRUCTIONS Double pythagorean theorem measurement Continuous measurement (locating) Use the double Pythagorean measurement mode when one end of the length to be measured indirectly is higher than the measurement position and the other end of that length is lower than the measurement position. In the illustrated example (see fig 4), the fig 4 B length BC is to be determined, and A is the measurement position. For this purpose, AB, ? AO and AC must be measured. AO and BC must form right angles. O A to choose 1. Press the mode key the double Pythagorean Theorem measurement mode. The mode icon will blink on the LCD screen. C to turn on the 2. Press the measure key laser beam; position the tool to aim the laser at the target B. to display the measured length of AB in the first row of the screen. 3. Press the measure key 4. Without changing the measuring reference point location of the tool in position A, aim the laser beam perpendicularly at the target O. to display the measured length of AO in the second row of the 5. Press the measure key screen. 6. Without changing the measuring reference point location of the tool in position A, aim the laser beam at the target C. again to display the indirect length of BC in the lowest row of the 7. Press the measure key screen; the distance AC will be displayed at the same time in the third row. The continuous measurement function (locating) is used for transferring measurements, e.g., from construction plans. In the continuous measurement mode, the laser distance finder/measuring tool can be moved relative to the target, during which time the measured value is updated approximately every 0.5 seconds in the display. For example, the user can measure the distance from the tool to a wall and then move away from that wall while the actual distance is continuously updated and displayed, informing the user when the correct distance has been reached. to choose the single-distance measurement mode. If in another 1. Press the mode key to go back to the single-distance measurement mode. mode, press the clear key and hold it for about 3 seconds to activate the continuous 2. Press the measure key measurement mode. 3. Move the tool until the required distance value is indicated at the bottom of the display. 4. Press any key to interrupt the continuous measurement. The current measured value is indicated in the lowest row of the screen. The minimum and maximum values will be displayed in the first and second row of the screen. again to start a new continuous measuring sequence. 5. Press the measure key LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 Minimum/Maximum measurement This function allows the user to measure the minimum or maximum distance measured from a fixed measuring point. It is commonly used to measure diagonal distances (maximum values), horizontal distances, or vertical distance (minimum values). The resulting value can be transferred to area, volume,Pythagorean Theorem measurement and single-distance measurement modes. Min/Max function can help eliminate the measuring deviation caused by holding the tool incorrectly when aiming at the target. It can help to get an accurate calculation of area, volume and indirect length. to choose among area, volume or Pythagorean Theorem 1. Press the mode key measurement modes. to activate the min/max function. 2. Press the min/max key to turn on the laser, aim the laser beam at the target you want to 3. Press the measure key measure and press it again to start the minimum or maximum measuring. 4. Slowly sweep the laser left and right or up and down over the desired target point. 5. Press any key to interrupt the min/max measuring; the minimum or maximum value will be displayed on the related row of the screen as an accurate length for calculation. OPERATING INSTRUCTIONS 16 15 OPERATING INSTRUCTIONS Addition and subtraction Error signals The single-distance, area, volume and indirect length can be added or subtracted with the addition and subtraction functions. 1. Take the first measurement. to choose addition or subtraction. 2. Press the plus/minus key 3. Take the second measurement. 4. The sum or difference between the measurements will be displayed in the lowest row of the screen, and the last measurements will be displayed at the same time in the upper row of the screen. 5. Follow the same method to make additional calculations. The following error signals may appear on the LCD of your tool during measuring: Working with the tripod (available separately) The use of a tripod is particularly helpful for measuring greater distances. The laser distance finder/ measuring tool can be screwed onto a commercially available tripod using the 1/4'' thread on the underside of the housing. 1. Mount the tool to the tripod. 2. Set the measuring reference to the thread, the icon shows . 3. Start to take measurements. LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 ERROR CODE CAUSE ACTION Err 001 The reflected laser light is too intense. Do not direct the laser at a highly reflective surface; cover the surface with white paper if necessary. Err 002 Out of range, the measuring range for this tool is from 0.1 to 50 m. Take measurement within the range of 0.1 to 50 m. Err 003 The target provides poor reflection of the laser. Change the measuring target or cover it with a piece of white paper. Err 004 The temperature is too high. Wait until the laser distance finder/ measuring tool has reached the operating temperature (-10 to 50ºC) Err 005 The temperature is too low. Wait until the laser distance finder/ measuring tool has reached the operating temperature (-10 to 50ºC) Err 006 Low battery, a reminder to replace the batteries. Insert new batteries Err 007 Strong vibration or the tool was moved quickly when measuring. Always keep the tool steady Err 008 Wrong input: the length of one side of the right triangle as measured is longer than the hypotenuse. Re-measure; the hypotenuse is always longer than the first side length LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 OPERATING INSTRUCTIONS 18 17 MAINTENANCE This Laser distance finder/Measuring tool been designed to be a low-maintenance tool. However, in order to maintain its performance, you must always follow these simple directions. 1. Always handle the tool with care. Treat it as an optical device, such as a camera or binoculars. 2. Avoid exposing the tool to shock, continuous vibration or extreme hot or cold temperature. 3. Always store the tool indoors. When not in use, ALWAYS store the tool in its protective case. 4. Always keep the tool free of dust and liquids. Use only a clean, soft cloth for cleaning. If necessary, slightly moisten the cloth with pure alcohol or a little water. 5. Do not touch the lens with your fingers. 6. Check the batteries regularly to avoid deterioration. ALWAYS remove the batteries from the tool if it is not going to be used for an extended period of time. is continuously displayed on the 7. Replace the batteries when the empty battery indicator LCD. 8. Do not disassemble the laser distance finder/measuring tool; this will expose the user to hazardous radiation exposure. 9. Do not attempt to change any part of the laser lens. PROBLEM POSSIBLE CAUSES SOLUTIONS Tool cannot be switched on Batteries are installed incorrectly Reinstall the batteries according to the polarity indicators in the battery compartment Batteries are low voltage Replaced with new batteries The power key did not contact well Try to press it more firmly or send for repair Error codes on LCD in measuring Please refer to “Error signals” above Please refer to “Error signals” above Short battery life Using incorrect batteries Use alkaline batteries If the problem remains unsolved after performing the checks described above, call the toll-free helpline, at 1-800-689-9928. Battery Disposal Please dispose the used battery per municipal and provincial law. LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 TROUBLESHOOTING 20 19 22 21 No. Part No. Description No. Part No. 1 2820226000 Contactor 14 3700479000 Positive Contactor Description 2 2820227000 Contactor 15 3704437000 Sponge Pad 3 2822565000 Contactor 16 3704438000 Adhesive Tape 4 2823407000 Main Support Assembly 17 3704492000 Sponge 5 3124608000 Battery Cover 18 3705522000 Paster 6 3124609000 Transparent Guard 19 4860008000 Inner Wire 7 3124610000 Cover 20 4890989000 PCB Assembly 8 3124611000 Adjusting base 21 4890920000 PCB Assembly 9 3124612000 Upper Guard 22 5610011000 Tapping Screw 10 3126711000 Push Button 23 5610075000 Tapping Screw 11 3320806000 Right Housing 24 5670252000 Pin 12 3321526000 Left Housing Assembly 25 5690181000 Seal Ring 13 3660407000 Spring If any parts are missing or damaged, or if you have any questions, please call the Toll-free Helpline, at 1-800-689-9928. LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 PARTS LIST PARTS LIST Exploded view WARRANTY g) this warranty will not apply to any product or part thereof if any part from another manufacturer is installed therein or any repairs or alterations have been made or attempted by unauthorized persons; h) this warranty will not apply to normal deterioration of the exterior finish, including but not limited to scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive and chemical cleaners; and i) this warranty will not apply to component parts sold by and identified as the product of another company, which shall be covered under the product manufacturer’s warranty, if any. This Mastercraft product is guaranteed for a period of 3 years from the date of original retail purchase against defects in workmanship and materials, except for the following components: Accessories, which are guaranteed for a period of 1 year from the date of original retail purchase against defects in workmanship and materials. Subject to the conditions and limitations described below, this product, if returned to us with proof of purchase within the stated warranty period, and if covered under this warranty, will be repaired or replaced (with the same model, or one of equal value or specification), at our option. We will bear the cost of any repair or replacement and any costs of labour relating thereto. These warranties are subject to the following conditions and limitations: a) a bill of sale verifying the purchase and purchase date must be provided; b) this warranty will not apply to any product or part thereof that is worn or broken or that has become inoperative due to abuse, misuse, accidental damage, neglect or lack of proper installation, operation or maintenance (as outlined in the applicable owner’s manual or operating instructions) or that is being used for industrial, professional, commercial or rental purposes; c) this warranty will not apply to normal wear and tear or to expendable parts or accessories that may be supplied with the product that are expected to become inoperative or unusable after a seasonable period of use; d) this warranty will not apply to routine maintenance and consumable items, including but not limited to fuel, lubricants, vacuum bags, blades, belts, sandpaper, bits, fluids, tune-ups or adjustments; e) this warranty will not apply where damage is caused by repairs made or attempted by others (i.e.: persons not authorized by the manufacturer); f) this warranty will not apply to any product that was sold to the original purchaser as a reconditioned or refurbished product (unless otherwise specified in writing); LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 Additional Limitations This warranty applies only to the original purchaser and may not be transferred. Neither the retailer nor the manufacturer shall be liable for any other expense, loss or damage, including but not limited to any indirect, incidental, consequential or exemplary damages arising in connection with the sale, use or inability to use this product. Notice to Consumer This warranty gives you specific legal rights, and you may have other rights, which may vary from province to province. The provisions contained in this warranty are not intended to limit, modify, take away from, disclaim or exclude any statutory warranties set forth in any applicable provincial or federal legislation. IMPORTED BY MASTERCRAFT CANADA TORONTO, CANADA M4S 2B8 LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0 WARRANTY 24 23