Transcript
LC11 / LC11M
Product Overview
LC11
Specification:
Material: Aluminum front panel, 0.8mm SECC body Color: Black & Silver Motherboard: Micro ATX Drive Bay: External - 5.25" x 1 Internal - 3.5" x 3 Cooling System: Front - 80mm intake, 2050rpm, 21dBA Left side - 80mm exhaust, 2050rpm, 21dBA Oversized mesh grill CPU air intake vent Riser Cards: 1 AGP + 2 PCI Expansion Slot: 3 Front I/O Port: USB2.0 x 4, IEEE1394 x 1, audio x 1, MIC x 1 Power Supply: TFX 240W PFC / TFX 300W PFC Net Weight: 7.2 kg Dimension: 424 mm (W) x 96 mm (H) x 430 mm (D)
Disassemble Chart
BOTTOM PANEL
3.5 BAY * 2 ( HIDDEN ) RISER CARD(AGP*1+PCI*2) MICRO ATX M/B
TFX 240W PFC POWER SUPPLY
BUTTON RIGHT PANEL DRIVE BAY DOOR
8025 FAN 8025 FAN
3.5 BAY * 1 ( HIDDEN ) TOP PANEL
5.25 BAY * 1
POWER SW FRONT IO (1394 + AUDIO) FRONT IO (USB * 4)
RESET SW LEFT PANEL
Product Overview
LC11M M
Specification:
Material: Aluminum front panel, 0.8mm SECC body Color: Black & Silver Motherboard: Micro ATX Drive Bay: External - 5.25" x 1 Internal - 3.5" x 3 Cooling System: Front - 80mm intake, 2050rpm, 21dBA Left side - 80mm exhaust, 2050rpm, 21dBA Oversized mesh grill CPU air intake vent Riser Cards: 1 AGP + 2 PCI Expansion Slot: 3 Front I/O Port: USB2.0 x 4, IEEE1394 x 1, audio x 1, MIC x 1 Multimedia: VFD, IR, remote control, iMON media center software Power Supply: TFX 240W PFC / TFX 300W PFC Net Weight: 7.2 kg Dimension: 424 mm (W) x 96 mm (H) x 430 mm (D)
Model Matrix
Optional PCI EXPRESS X16 RISER CARD
LC11B(Black) 240w(PFC)
LC11B - M Multimedia
LC11S(Silver)
LC11S - M
LC11B - 300
LC11B - M300
MODEL
Multimedia
300w(PFC) LC11S - 300
LC11S - M300
RC01【Sold Separately】
1. Remove LC11 from the carton
2. Remove bottom cushion and plastic bag from the case (do not peel off the protective film on top of the case)
3. Rest case on the top cushion with the bottom of the case facing up
4. Remove two lower screws to slide the bottom cover off the case
5. Unscrew screws securing the 3.5" drive bracket to remove it from the case
6. Use #6-32 X 6 screw for securing hard drive in the 3.5"drive bracket as shown (up to two hard drives can be installed)
7. Re-insert drive bracket back into the case and secure with screws
8. Use included hex wrench to remove the screw located near the optical drive bracket as shown
9. Use hex wrench to remove two screws located on the right side of the case as shown
10. Carefully remove aluminum front panel located in front of the optical drive
11. Slide optical drive into the drive bracket as shown
12. Secure optical drive with M3 screws (an additional 3.5" hard drive can be installed in the slot beneath the optical drive)
13. Install Micro-ATX motherboard into the case
14. Connect all required cables and connectors to installed drives
15. Remove riser card bracket as shown
16. Remove screw from expansion slot fastener as shown
17. Swing fastener into open position to release expansion slot covers
18. Assemble AGP riser card, PCI riser card, and riser card bracket into one module as shown
19. Insert completed riser card module into the motherboard
20. Secure riser card module with screw removed from step 15
21. Install AGP/PCI cards and secure them with expansion slot fastener re-attached to the back of the case
22. Take great care when installing an appropriate CPU cooler, the height of the cooler cannot exceed 75mm
23. After all required wires are connected, re-install the bottom case cover back onto the case
24. Turn case over on its feet and peel off the protective film to complete installation
11
Insert the 4 pin USB connector from the VFD/IR module to your motherboard USB pin header. You can also use the included USB adapter to connect to an external USB port header on the motherboard
From the front panel VFD/IR module, locate two female single wire leads colored in black and red. The black wire should have the connector labeled, "GND"
From front panel
Refer to your motherboard manual and connect the two wire leads to "power switch" or "power button" on the motherboard's front panel pin headers
From VFD/IR module
Connect your power switch connector from the front panel to the dual pin header from the VFD/IR module
Connect the included ATX adapter to your power supply's ATX connector.
From ATX adapter
Connect the other end of the ATX adapter to your motherboard. It is compatible with 24pin or 20pin motherboards.
From VFD/IR module
Finally, connect the 3 pin power connector from the VFD/IR module to the ATX adapter's 3pin cable
ation
December , 2005
NO:11400208
