Transcript
13/07/2006
Ins-30021 CARDLOCK compact, 2005 design Technical Support
+44(0)845 8381716
[email protected]
Technical help is available Monday - Friday from 07:00 - 19:00.
Quickstart guide This supplement is a brief guide to installing a CARDLOCK compact system. For more information visit http://www. paxton-access.co.uk/ or call the sales team on +44 (0)845 838 1716.
Fitting
Reader covers A black and satin chrome cover come supplied with the reader. Additional covers are available in grey, blue and silver. Registered installers can order these free of charge by logging onto the secure installer extranet: https:// extranet.paxton-access.co.uk/index.asp If you are not a registered installer please call us on +44 (0)845 838 1716 for more information.
Wiring To 12V dc Power supply
Exit
Exit button (push to make)
Reader NOTE: Compact readers cannot be connected to a relay 12V DC release current rating must be less than 1A.
Electric release
Reset - Use 1 method, not both
Wire outputs +12V d.c. 0V Lock 12V Lock 0V Exit input Exit 0V
1. Power down the unit 2. Press and hold the exit button 3. Power up the unit - wait for beep/red LED to go out 4. Release and press the exit button a further 2 times (within 3 seconds) 5. The reader will beep 6 times OR 1. Present Enrolment card 2. Present Door open time card twice 3. Present Enrolment card 4. Present Door open time card twice 5. WAIT FOR 5 SECONDS!
Enrolment Card - must be presented/swiped when the system is first switched on 2 1.
A n o a e 1. card tok alid is e foll r e th re-v nt th ade To se re n. 2. pre the ke to to er us
4 1. At installation, present this card to the reader to validate the tokens in this pack. 2. To re-validate a user token, present this enrolment card to the reader followed by the user token.
rd CK ca this ate LO nt sentvalid RD lme n, preer to ack. ken, e CA ro llatio readthis p ser tont card th y en t instato thens in te a urolmewed b
3 CARDLOCK enrolment ca
ins the in thi er card At to s a uslment by the card token ate ro ed the valid s en low re- t thi r fol To de en 2. rea . pres en the to tok user
rd CK LO nt ca this t RD e ate esenvalid CA to rolmlation, pr der pack. en en, tal rea s tok
1
! EP BE P! E BE rd CK ca this ate LO nt sentvalid RD lme n, preer to ack. ken, e CA ro llatio readthis p ser tont card th y n ta e in s e t in to th ns te a urolmewed b A n o a e 1. card tok alid is e foll r e th re-v nt th ade To se re n. 2. pre the ke to to er us
1. Take the enrolment card from the new pack of user cards 2. Present/swipe the enrolment card to the reader 3. The reader beeps and the LED’s become lit as the enrolment card is acknowledged 4. All cards in the pack are now valid. The enrolment card can now be returned to it’s pack. To add extra packs see card pack instructions
Issuing tokens 1 Shadow cards
2
3
4
CARDLO
CK
User Ca
rd CARDLO
CK
User Ca
rd
CARDLO
CK
User Ca
rd CARDLO
CK
User Ca
rd
CA
Us
er
CARDLO
CK
User Ca
RD
LO
Ca
CK
rd
rd CARDLO
CK
User Ca
rd
CARDLO
CK
User Ca
rd CARDLO
CK
User Ca
rd
User cards 1. 2. 3. 4.
On each page there are 4 ‘pairs’ of cards - a ‘User card’ and a corresponding ‘Shadow card’ Write the name of the user on the shadow card Take the user card from the opposite pouch and issue to the user Keep the card pack containing the shadow cards in a safe place
Bar a user 2
3
4
ith Sm Jo
is
rd
e
K
na
Sw
m
e:
ip
e
RD LO C
Ca
W rit
er
th
CA
Us
hn
ca
rd
to
ba
r:
John Smith
John Smith
: Write name
bar: s card to Swipe thi
1
1. When a card is lost or stolen it is important to bar the missing card from your system to avoid unauthorized access 2. To bar a card or token take it’s corresponding shadow card from the card pack 3. Present/swipe the shadow card to the reader. This will remove the lost card or token from your system 4. Should a barred user card become found the system administrator can re-validate it by presenting/swiping the enrolment card followed by the user card to the reader
Fail open release card - PROXIMITY compact systems are fail closed as default 1
2
3
pen Fail o
h d wit n d is use fail ope This cars where a used for nt of system release is the eve ough c electri ration in thr card ope open safe Swipe the e a fail . ipe a fire der to driv ck. Sw the rea or maglo revert to fail release d again to the car operation. closed
rd se ca
P!
E BE
relea
il
re
e
as
le
en
rd se ca
relea pen Fail o
h d wit n d is use fail ope This cars where a used for nt of system release is the eve ough c electri ration in thr card ope open safe Swipe the e a fail . ipe a fire der to driv ck. Sw the rea or maglo revert to fail release d again to the car operation. closed
d
r ca
4
!
P BEE
op
h pen f wit il o for t o ed fa ed en gh us a us ev rou en p e is re is th rd th il o rd he e il ca w as in ca a fa ipe fa w to is ms le on e Th ste ic re rati e th rive k. S ert d c v sy ctr ope wip lo re ele fe . S er to ag to sa fire ad r m ain n. a e re se o ag tio th lea ard pera re e c d o th se clo
Fa
NOTE: THIS CARD CAN ONLY BE USED WITH A FAIL OPEN LOCK 1. Take the fail open release function card from the starter pack 2. Present/swipe the card to the reader. The reader will beep for about a second 3. The reader is now set to fail open mode. This allows safe operation of the door in case of fire: The lock will release when the power is cut 4. To revert to fail closed mode, present/swipe the card again. When the reader sounds fail closed mode has been activated
Door open time (seconds) 3
4
open
open
time
time
! EP BE P! BEE
Door
Door
is door t the d iod tha n a vali The per for whe ed set as the unlock swiped is card; is card : Swipe thiswait for the the follows will bleep; swipe will reader d period; eping require in; the ble aga card stop.
2
is door t the d iod tha n a vali The per for whe ed set as the unlock swiped is card; is card : Swipe thiswait for the the follows will bleep; swipe will reader d period; eping require in; the ble aga card stop.
1
e
tim
en op or oor isd Do e d vali
e th a s a ; th the at n th whe set ard for c d e rio for ed is this ait th will w e g pe d ip e ke wip e p; Th loc is s Swip lee ; sw epin un rd s: ill b riod ble a e w c llo r w pe th fo ade ed in; ir a re qu ag re rd ca p. sto
1. 2. 3. 4.
Take the door open time function card from the starter pack Present/swipe the card to the reader. The reader will start beeping Wait for the required period you wish the door to remain open Present/swipe the card again at the end of the period to set the open time. The beeping will stop
Silent operation
card
card ation t oper
ation
t oper
P!
E BE
Silen
4
nce the d to sile by the de this car Swipe noises ma d again car beeping Swipe the beeping reader. nable the to re-e noises.
3
Silen
2
nce the d to sile by the de this car Swipe noises ma d again car beeping Swipe the beeping reader. nable the to re-e noises.
1
! EP BE P! E BE
rd
n
tio
nt
ca
ra pe
o
e th ce e en th sil by gain a to de a ard g rd ca es m e c epin is e th nois e th e b e ip g wip th Sw epin r. S able be ade en re re- s. to ise no
le
Si
1. 2. 3. 4.
Take the silent operation function card from the starter pack Present/swipe the card to the reader. The reader will beep The reader is now in silent operation mode Present/swipe the card again to disable silent operation mode. The reader will beep twice
Specifications Electrical Supply voltage required
11 min
12 typ
Continuous output current of reader Voltage supplied by kit power supply
15 max 1 max
11.4 min
12.0 typ
Current capacity of kit power supply
12.6 max 1.1
V d.c. A V d.c. A
Mains supply voltage
90 min
240 max
Mains supply frequency
50 min
60 max
Hz
V a.c.
Product specific information Quiescent current
45
70
mA
Door open time
1
60
s
Number of zones
1
Number of time zones
3 2
Reader life
1,000,000
Readers per door Readers per site
1
No limit
Fail open release
Yes
Silent operation
Yes
Water resistance
IPX7
Vandal resistance
Medium
Security
Low
Cards accepted Dimensions Ambient temperature
swipes
1
Track 2 ABA 34 w -20 min
89 h
34 d +55 max
mm °C
