Transcript
Page 1 / 3
LED CONTROLLER
CTR-BOX
ITEM NO.:
INSTRUCTION OF CTR-RGB-BOX There are 6 groups RGB output in the controller, with 32 built-in programs, timing on / off function, automatic storage parameters, compatible with international standard DMX512 signal, 6 separate DMX address. Which can provide convenience and simple installation in the project. It is used for 24V/12V DC RGB products (usually saying, DC input , 4wires and 3circuits), especially the underground light, pool light, built-in ceiling light, RGB strip, spot light , etc.
A. Character：
Protection：
L292xW176xH127mm Aluminum Alloy 4KG 120V/240V 24V/12V 300W (6x50W) (max) 180W (6x30W) (max) IP20
300 180
127
161.5 176
Size： Housing Material： Weight： Input Volt： Output Volt： Power：
Mounting dimension (Figure 1)
B. Installation: B-1.Introduction： Fix the screws (x4) into the ground firstly, hang the box and lock the nut . (Figure 2) B-2.Connection (Figure 3)： Firstly, take apart the PC cover, remove the terminals, wring the output terminal as shown in Figure 3 , then plug the terminal on the pins (original position), separate the bonding clamp for compressing the wire and lock the PC cover. 4 colors(red, green, blue, black) in our 4wires and 3 circuits products. Wiring corresponding follows: Black wire ----------- V+ Red wire ----------- R Green wire ----------- G Blue wire ----------- B *Please refer to actual definition of color of cable in different fixtures.
Display
Connection
Control Box Nut
Screw
Wall
(Figure 2)
PC Cover Wring the output terminal
Bonding clamp Pins Wring the output terminal
R G B V+
C . Function and Operation C - 1 . Buttons : MODE : Function selection SET:Parameter selection ( press once then move next ) UP : + DOWN : C - 2 . Time Setting (Figure 4)： Press the MODE button to the interface as Figure 4 , 2012 begins to flash , press UP , DOWN button adjusted to the desired year , then press the SET button to 12 , as adjusted to the desired month by the UP , DOWN button , and then press the SET button to the next . C - 3 . Timing ON / OFF Setting (Figure 5) Press the MODE button to the interface as Figure 5 , the number 13 of the 13 : 08 begin to flash , press UP , DOWN button adjusted to the desired hours , and then press the SET button jump to 08 , as adjusted to the desired minutes Press the UP , DOWN button , and then SET button to the next .
(Figure 3)
System
Time
Set
2012-12-25 : 10:24
MODE
SET
UP
DOWN
(Figure 4)
ON
OFF
：17:00
13:08
MODE
SET
UP
(Figure 5)
DOWN
Page 2 / 3
LED CONTROLLER
ITEM NO.:
C - 4 DMX Address Setting (Figure 6) Press the MODE button to the interface as Figure 6 , the 001 ( back of the A ) starts flashing , press the UP and DOWN button adjusted to the desired address , then press the SET button jump to the 002 ( back of the B ) , Press the UP , DOWN button adjusted to the desired address and then SET button to the next . Note : A001 corresponds to 1 # terminal , B002 corresponds to 2 # terminal , address and serial number correspond in the order . * * * Valid address : 001 ~ 512
A001
B002
C003
D004
E005
F006
MODE
1#
2#
SET
3#
UP
CTR-BOX
DOWN
4#
5#
6#
(Figure 6)
C - 5 Function Switch Setting (Figure 7) Press the MODE button to interface as Figure 7 , 20 is flashing , press UP , DOWN button adjusted to the desired function number , then press the SET button so the Speed is flashing . Adjusted speed by UP and DOWN button . Other function number is similar to this way .
Program No.
Note : The above operations adjusted to the desired parameters , flashing wait about 5 seconds , then complete the automatic storage.
Program
Speed
20 Lelf Flow Speed: 100
MODE
SET
UP
DOWN
(Figure 7)
D．Program Menu
29 Pingpong
Setup
00 BlackOut
10 Color Flash Speed: 100
20 Left Flow Speed: 100
30 Rainbow Left Speed: 100
01 Static Red Brightness:255
11 Red Fade Speed: 100
21 Right Flow Speed: 100
31 Rainbow Right Speed: 100
02 Static Green Brightness:255
12 Green Fade Speed: 100
22 Bidir-Flow Speed: 100
32 AutoRun Mode Cycle: 16
03 Static Yellow Brightness:255
13 Yellow Fade Speed: 100
23 Side->Middle Speed: 100
04 Static Blue Brightness:255
14 Blue Fade Speed: 100
24 Middle->Side Speed: 100
05 Static Purple Brightness:255
15 Purple Fade Speed: 100
25 Side<->Middle Speed: 100
06 Static Cyan Brightness:255
16 Cyan Fade Speed: 100
26 Left Stack Speed: 100
07 Static White Brightness:255
17 White Fade Speed: 100
27 Right Stack Speed: 100
08 Dimmer R255 G255 B255
18 Color Fade1 Speed: 100
28 Bidir-Stack Speed: 100
09 Color change Speed: 100
19 Color Fade2 Speed: 100
29 Pingpong Speed: 100
UP or DOWN
Welcome To Use Master Pro V1.0
Speed/Brightness/Cycle can be adjusted with each function! ***Speed range: 0~100(fastest) ***Brightness range: 0~255(brightest) ***Cycle range: 1~16
MODE
System Setting DMX Address # x
Setup
System Time Set 2001-00-01 18:43
Setup
ON ---> OFF 18:14--->23:04
Setup
Quantity: Define the quantity loaded by controller Start Addr: Define the starting DMX address of the 1st fixture
YEAR-2001 MONTH-00 DAY-01 HOUR-18 MINUTE-43
Use 【UP】or 【DOWN】to adjust all active parameters! On-Controller start to work OFF-Controller stop to work
DMX address of 1#~6# fixtures is not required to be of serial, under built-in programs/functions.
Page 3 / 3
LED CONTROLLER
ITEM NO.:
CTR-BOX
E．Addressing E - 1 . When selected parameter stop flashing or exit present operation , setting will be recorded automatically; Do not cut the power off during setting . E - 2．Connect the fixture / 4wires into the terminals R (-), G (-), B (-), V + strictly and tightly . E - 3．Display address A , B , C , D , E , F , and 1 #, 2 #, 3 #, 4 #, 5 #, 6 # are corresponding; E - 4 . Once the parameter setup cannot be recorded correctly , please replace the cell battery duly .
F . DMX Signal Connector
2
1
1--Shiled 2--Data3--Data+
3
G． Caution G - 1 The controller should be installed indoor and far away from disturbance from electric or magnetic field . G - 2 Connect light fixtures to controller box strictly as per requirement , otherwise it will lead to failure of function performance or even damage to the circuit . G - 3 Pay attention to the max output power , avoid overload and short - circuit . G - 4 Replace the fuse / 10A , if there was no output volt . G - 5 Do not dismantle the control box once failed , turn to dealer or professional person for replacement or repairing .
Warning： 1 . Max . Max . 2 . Max . Max .
Loading Loading Loading Loading
Power Power Power Power
of of of of
24V Controller Not Exceed 300W per Terminal Not Exceed 50W ! 12V Controller Not Exceed 180W per Terminal Not Exceed 30W !
The above instruction are subject to update or improved without notice.Pls turn to our staff for further details ! Thanks for your long term support !
