Transcript
1 CABLE SUSPENDED Lumium Cat. #: Project: Type:
PRODUC T DESCRIPTION: Small in size, yet large in visual impact, Trinium 1 combines minimalism with subtle details to present a thin, dynamic element to any environment. The clean geometry juxtaposition of convex and concave create a unique look which is enhanced by precision engineering and an exquisite attention to detail. Power can be carrid through the aircraft cable or low voltage coax cable to complete the minimalistic aesthetic
HOUSING: ALUMINUM EXTRUSION PRECISION MACHINED ALUMINUM END CAP VARIOUS COLOR TEMPERATURE HIGH PERFORMANCE LEDs
1-1/2”
(CS)
FEATURES: Distinctive convex/concave triangular profile Precision engineered linear light fixture 3/64” aircraft cable or Power through the Aircraft Cable suspension options 360 rotation option - with mechanical locking No visible fasteners Extruded aluminum housing 3/8” thick machined end caps
HIGH EFFICACY REFLECTOR FROSTED CLEAR OR FROSTED WHITE LENS
1-5/8”
P R O D U C T S P E C I F I C AT I O N FIXTURE TYPE
MOUNTING
Tr1
CS
Tr1 Trinium 1
CS Cable Suspended
FIXTURE ORIENTATION
LED DRIVE POWER*
COLOR TEMP
LAMP*
LED LED
D Direct I Indirect R Rotational
27K 30K 35K 40K 50K
2700K 3000K 3500K 4000K 5000K
VL L M H CU
VERY LOW LOW MEDIUM HIGH Custom: Specify desired output
*See Page 4 for more information
HARDWARE DETAIL FINISH
MF Machined Finish (standard) SC Satin Clear (Anodize) SP Specular (Chrome-like) CF Custom Finish (Consult factory)
DRIVER HOUSING FINISH
NA MA SC SW CF
NOMINAL LENGTH
Not Applicable Mill Aluminum** Satin Clear Satin White Custom Finish (Consult factory)
CANOPY FINISH
CANOPY SIZE OPTIONS*
SW Satin White CC Custom Canopy finish*
55 5” Power feed canopy 5” non-power feed canopy 52 5” Power feed canopy 2” non-power feed canopy 50 5” Power feed canopy No canopy on non power side
**Most cost effective if finish is not important
*Consult Factory
1’ 2’ 3’ 4’ SPECIFY CUSTOM
1 120v 2 277v U Universal (120-277v)
G B CB BS
AIRCRAFT CABLE LENGTH*
4 4’ CL_ Custom Length Specify in feet Powered Aircraft (ie: CU6 for 6’) Cable (no power Consult factory cord) to confirm spec Gray Black Clear Braided Braided Sleeve (Steel weave) Custom Cord* OPTIONS
*Consult Factory
SC Satin Clear (Anodize) SW Satin White (powder coat) SP Specular (Chrome-like) CF Custom Finish (Consult factory)
SD Standard Driver 1D 1% DIM 10D 10% DIM
10% DIM is slightly more cost effictive than 1%.
W White PAC
HOUSING FINISH
DRIVER
Each number is nominal length. Segment dimension is 11-1/8”. Fixtures can be as long as desired. Fixtures over 8’ may be broken up into multiple sections. Consult factory with questions.
POWER CORD COLOR
CC *See options section and installation instructions for more information.
1 2 3 4 ... CU
VOLTAGE
*Cables are field adjustable
LENS
CF WF NL CC
OPTIONS/ CUSTOMIZATION*
Blank No customization Clear Frost EMB Emergency White Frost Battery backup** No Lens CR Cusomization Custom Color* Requested* Lumium offers an array of options - See the options section for more information. Custom concepts are also possible
*Consult Factory
*Consult factory for all custom options or custom concept requests **EMB: See DRIVER section below
S P E C I F I C AT I O N I N F O R M AT I O N GENERAL NOTES :
All fixtures are UL listed for dry and damp locations. Please contact the factory with any specification questions. Italicized grayed out options may have additional costs and/or lead times.
F I XTURE OR IENTATION:
“Direct” (D) for downlight applications “Inirect” (I) for uplight applications “Rotational” (R) for adjustable applications: 360 degree rotational capacity
VOLTAGE:
System voltage is helpful as it provides more driver options, however, the Universal (U) option is fine for LED applications.
DRIVER:
The standard driver may also be a dimmable driver. By not using the 0-10v wires, the fixture will switch on to 100%. 1) DIMMING: 0-10v to 1% or 10%. Contact factory for other dimming options. 2) EMERGENCY: Specify EMB under the Options/Customization category at the end of the cut sheet and contact factory with specific requirements.
F I NI S HES :
The standard finish is a satin white powder coated or satin clear anodized housing with Machine Finished hardware. Machined finish is preferable for the machined components (Hardware Detail) - Powder coating may result in additional costs. Please consult the factory with any questions about standard or custom finishing options.
A IRC R A FT C A B L E L E N GT H :
Aircraft cable is field adjustable and cutable. For drops longer than 4’, specify a cable length which encompasses that distance.
L E NSES:
Clear Frost (CF) Highly transmissive lens, but does have lamp imaging with this fixture. White Frost (WF) should be used when lamp imaging is a concern. This option slightly reduces fixture efficacy.
C USTO M IZAT IO N:
We have numerous custom options available. From simple options to complete custom requests, we are more than willing to accommodate any creative notions you might have. Just ask.
Lumium Lighting, LLC | 3820 Oceanic Dr., Suite 306, Oceanside, CA 92056 | Phone: 760.757.2530 | Fax: 760.283.2333 | www.lumiumlighting.com While we always strive to ensure all website content and product information is current, Lumium Lighting reserves the right to change specifications without notice. 2012 Lumium Lighting, LLC - All rights reserved.
Tr1-0813
2 R O TAT I O N A L A R M M O U N T Lumium Cat. #: Project: Type:
PRODUC T DESCRIPTION: Small in size, yet large in visual impact, Trinium 1 combines minimalism with subtle details to present a thin, dynamic element to any environment. The clean geometry juxtaposition of convex and concave create a unique look which is enhanced by precision engineering and an exquisite attention to detail. Power can be carrid through the aircraft cable or low voltage coax cable to complete the minimalistic aesthetic
HOUSING: ALUMINUM EXTRUSION PRECISION MACHINED ALUMINUM END CAP VARIOUS COLOR TEMPERATURE HIGH PERFORMANCE LEDs
1-1/2”
FEATURES: Distinctive convex/concave triangular profile 360 rotation with mechanical locking High efficac LEDs Various finish and detail options High transmission frosted lenses No visible fasteners Extruded aluminum housing 3/8” thick machined end caps
HIGH EFFICACY REFLECTOR FROSTED CLEAR OR FROSTED WHITE LENS
1-5/8”
P R O D U C T S P E C I F I C AT I O N FIXTURE TYPE
MOUNTING
LAMP
Tr1
R AM
LED
Tr1 Trinium 1
RAM Rotational Arm Mount
LED
COLOR TEMP
30K 35K 40K 50K
3000K 3500K 4000K 5000K
LED DRIVE POWER*
VL L M H CU
VERY LOW LOW MEDIUM HIGH Custom: Specify desired output *See Page 3 for more information
HARDWARE DETAIL FINISH
MF Machined Finish (standard) SC Satin Clear (Anodize) SP Specular (Chrome-like) CF Custom Finish (Consult factory)
DRIVER HOUSING FINISH NA MA SC SW CF
Not Applicable Mill Aluminum** Satin Clear Satin White Custom Finish (Consult factory)
(RAM)
MOUNTING/ COVER PLATE 4CPF FLAT 4” diameter Cover Plate - For use with a 3-O mud ring 4CPC CURVED 4” diameter Cover Plate - For use with a 3-O mud ring 1TR 1” Trim Ring - for use when mounting to furniture CCP Custom Cover Plate (Consult factory)
NOMINAL LENGTH
1 2 3 4 ...
1 120v 2 277v U Universal (120-277v)
1’ 2’ 3’ 4’ SPECIFY
Each number is nominal length. Segment dimension is 11-1/8”. Fixtures can be as long as desired. Fixtures over 8’ may be broken up into multiple sections. Consult factory with questions.
ARM LENGTH 6 9 12 18 CAL
VOLTAGE
6” 9” 12” 18” Custom Arm Length Consult factory
LENS
CF Clear Frost WF White Frost CC Custom Color
DRIVER
SD Standard Driver 1D 1% DIM 10D 10% DIM
HOUSING FINISH
SC Satin Clear (Anodize) SW Satin White (powder coat) SP Specular (Chrome-like) CF Custom Finish (Consult factory)
10% DIM is slightly more cost effictive than 1%.
OPTIONS/ CUSTOMIZATION*
Blank No customization EMB Emergency Battery backup** CR Cusomization Requested* Lumium offers an array of options See the options section for more information. Custom concepts are also possible *Consult factory for all custom options or custom concept requests **EMB: See DRIVER section below
**Most cost effective if finish is not important
S P E C I F I C AT I O N I N F O R M AT I O N GE NERAL NOTES :
All fixtures are UL listed for dry and damp locations. Please contact the factory with any specification questions. Italicized grayed out options may have additional costs and/or lead times.
VO LTAGE:
System voltage is helpful as it provides more driver options, however, the Universal (U) option is fine for LED applications.
A RM LE NGTH :
Arms can be specified to desired lengths. Please note, arm lengths longer than 18” may require additional support depending upon the fixture and options.
DRIVER:
The standard driver may also be a dimmable driver. By not using the 0-10v wires, the fixture will switch on to 100%. 1) DIMMING: 0-10v to 1% or 10%. Contact factory for other dimming options. 2) EMERGENCY: Specify EMB under the Options/Customization category at the end of the cut sheet and contact factory with specific requirements.
F I NI S HES :
The standard finish is a Satin White powder coated or Satin Clear anodized housing with Machined Finish hardware. Machined finish is preferable for the machined components (Hardware Detail) - Powder coating may result in additional costs. Please consult the factory with any questions about standard or custom finishing options.
M O UNT ING PL AT ES:
The standard arm mounting configuration uses 3-O mud rings, a steel mounting plate, and machined cover. A small 1” O.D. ring can be used with furniture applications. See installation instructions or consult factory with any questions.
L E NSES:
Clear Frost (CF) Highly transmissive lens, but does have lamp imaging with this fixture. White Frost (WF) should be used when lamp imaging is a concern. This option slightly reduces fixture efficacy.
C USTO M IZAT IO N :
We have numerous custom options available as seen above. From simple options to complete custom requests, we are more than willing to accommodate any creative notions you might have. Just ask.
Lumium Lighting, LLC | 3820 Oceanic Dr., Suite 306, Oceanside, CA 92056 | Phone: 760.757.2530 | Fax: 760.283.2333 | www.lumiumlighting.com While we always strive to ensure all website content and product information is current, Lumium Lighting reserves the right to change specifications without notice. 2012 Lumium Lighting, LLC - All rights reserved.
Tr1-0813
4 DETAILED SPECIFICATION INFORMATION
LUMEN OUTPUT
(PER 12” NOMINAL LENGTH BOARD*)
LUMEN OUTPUT* DRIVER OUTPUT
VERY LOW LOW MEDIUM HIGH
WATTAGE
NO LENS
CF LENS
WF LENS
3 6 9 12
375 725 1050 1350
315 615 890 1150
260 505 745 965 CF = CLEAR FROST WF = WHITE FROST
LED COMPONENT MANUFACTURER OSRAM/SYLVANIA Distributed Array - Generation II Manufacturer’s lumen potential: 145 Lumens Per Watt* 80+ CRI Uniform light distribution Exceptional binning (LED color consistency) 60,000+ hours 0-10v dimming is a standard option 5 year system warranty
PER 4’ FIXTURE
(TOTAL DELIVERED LUMENS - DIRCT & INDIRECT)
DRIVER OUTPUT
VERY LOW LOW MEDIUM HIGH
WATTAGE
NO LENS
CF LENS
WF LENS
12 24 36 48
1,500 2,900 4,200 5,400
1,260 2,460 3,560 4,600
1,040 2,020 2,980 3,860
*Actual fixture efficacy will be dependent on specification. Please contact the factory with questions or for more information.
*Lumen output will vary depending on ambient temperature. Cooler temperatures result in higher luminaire performance. VERY LOW: Considerably underdrive the LEDs for minimal ambient light applications LOW: Underdrive the LEDs to about half of the fixture’s lumen potential MEDIUM: Slightly underdrive the LEDs for the best combination of lumen output and fixture efficacy HIGH: Drive the LEDs at maximum capacity for highest lumen ouput with good efficacy NOTE: Other wattage settings are possible through custom driver settings. Consult factory or local rep with specific requirements and we will do our best to meet your needs.
Lumium Lighting, LLC | 3820 Oceanic Dr., Suite 306, Oceanside, CA 92056 | Phone: 760.757.2530 | Fax: 760.283.2333 | www.lumiumlighting.com While we always strive to ensure all website content and product information is current, Lumium Lighting reserves the right to change specifications without notice. 2012 Lumium Lighting, LLC - All rights reserved.
Tr1-0813
O.1
OPTIONS GUIDE
GENERAL OPTIONS* *NOT ALL OPTIONS ARE AVAILABLE WITH EVERY FIXTURE *NOT ALL OPTIONS SHOWN
M O UNT IN G OPTI ONS Cable Suspended (CS) 1/16” aircraft cable suspension system. Fixtures can be static down-lights: Direct, static up-lights: Indirect, or Rotational (see CSR below). Standard and custom power cord finishes, sleeve options, and canopy colors offer options to match almost any space. Stainless steel cables come in various lenghts (4’ is standard) and are field adjustable. Cable Suspended Rotational (CS-R) Using a similar setup to the Cable Suspended system above, the Cable Suspended - Rotational system has 360 degree rotational capcity with mechanical fasteners to lock fixtures in place if desired. This system offers incredible flexibility, light direction control, and a dynamic aesthetic. Rotational Arm Mount (RAM) This system uses 1/2” to 5/8” diameter aluminum arms and subtle details in combination with 360° rotational capacity to create some of the most versatile linear fixtures in the architectural market. Standard mounting uses 3-O mud rings (supplied by others) or a 1” optional trim ring for furniture mounted applications. Engineered with no visible fasteners, smooth rotation, and mechanical locking, the RAM system reveals an impressive aesthetic with exceptional versatility. Asymmetric Mount (ASM) A unique configuration wherein the fixture is balanced from an off-center mounting point creating a dynamic aesthetic. This mounting option also allows some integral ballast options on the “1” series fixtures with standard T5 lamps. Direct, indirect, or rotational options round out this creative mounting option. Surface Mount (SM) (Ceiling Mount or Wall Mount - CM or WM): Fixtures mount directly to the surface. Ceiling or Wall Mount specification denotes the power feed hole location(s). Optional stand-offs allow for fixtures to be mounted from 1/2” to 12” as well as custom lengths if needed.
CONT I N U O U S R U N O PTIO N S Continuous runs are available with all fixtures and have several connection options. Single Seam continuous run options offer smooth section transitions while Component Seams lend to a more dramatic visual statement. The 360 (degree symbol) Rotational option enables individual sections to rotate independently of each other, which offers adjustable asymmetric light distribution capacity along with striking appearances such as alternating up/down fixtures or spiral transitions. The flexibility within the rotational option makes for infinite design and functional possibilities.
Continuous Run Single Seam
Continuous Run Component Seam
COLO R A N D F I N I S H O PT IO N S
Specular
Satin White Power coat
Continuous Run Rotational (Spiral effect)
F INISH CONF IGU R ATIONS Custom Finish examples*
Satin Clear Anodizing
Continuous Run Rotational
Gunmetal
*Custom Finishes
Nickel Plating
Tl2
Standard Finishes
Satin Clear anodizing and Satin White are standard finishes. Our Satin White is a semi-matte powder coating finish with a subtle, rich luster. Numerous custom anodizing and powder coated finishes are available as well. If you have a particular color/finish treatment in mind, please contact the factory and we will do our best to accommodate your project needs.
Standard finish configurations are Satin Clear (SC) or Satin White (SW) housings with Machined Finish (MF) machined components (end caps, knuckles, cover plates, etc.). The incredibly clean detail within all of the machined components lends to an incredibly high end aesthetic with a two tone finish.
Matte Black
RAL Colors
Bronze
Color Anodize
Color Powder coat
Brushed
*RAL and Custom Finishes may involve additional costs and may have fixture length restrictions. Please consult the factory with any questions or for specific finish information.
Thallium 2 (Tl2), Cable SuspendedRotational with two-tone finish: Satin Clear housing and Machined Finish components.
Lumium Lighting, LLC | 3820 Oceanic Dr., Suite 306, Oceanside, CA 92056 | Phone: 760.757.2530 | Fax: 760.283.2333 | www.lumiumlighting.com While we always strive to ensure all website content and product information is current, Lumium Lighting reserves the right to change specifications without notice. 2012 Lumium Lighting, LLC - All rights reserved.
Options-0813
O2
Oxygen 2 (O2), Rotational Arm Mount system with single tone finish: Satin Clear housing and Satin Clear components.
OPTIONS GUIDE
O.2
GENERAL OPTIONS*
(continued)
*NOT ALL OPTIONS ARE AVAILABLE WITH EVERY FIXTURE *NOT ALL OPTIONS SHOWN
KN U C K LE O P T I O NS Almost all Lumium fixtures have mounting options with rotational capacity. Flat knuckles are standard and require no change to any RAM or CS-R specification. Concave and Convex knuckles are optional and can be specified under the “Options/Customization”. Use the annotations listed to the right. Other custom options are available such as larger knuckles to match a fixture’s size or custom shapes if a specific aesthetic is destired. Consult factory with any questions or further customization requests.
Tl1
Flat Knuckle (standard)
Thallium 1 - Rotational Arm Mount Standard Flat Knuckle
Concave Knuckle (CCK) (optional)
O2 with matching knuckle size
2” or 3” (or other diameter) knuckle - works well matching fixtures in the Oxygen series
Convex Knuckle (CXK) (optional)
N2 with custom square knuckle
Square Knuckle (Custom)
Custom limited only by one’s imagination
Trim Ring (TR) 1-1/4” diameter trim ring Can be used in applications such as desk mounting
Custom Your imagination is the catalyst for creativity
CO VE R P LAT E O P T IO N S Cover plates are standard for Rotational Arm Mounting (RAM) systems. Standard options are Flat (FT), Curved (CV), or Trim Ring (TR). With certain applications, cover plates or trim rings may not be necessary. Contact factory with questions or for more information. Custom cover plates are also available. if a certain aesthetic is desired, please contact the factory to review any concepts and we will do our best to bring your vision to life.
Lightstream is our unique 1/16” aperture lens that creates a striking light accent. This design element is inherent to the Radium2 (Ra2) and Rubidium2 (Rb2) fixtures and can be specified as an option on the Thallium2 (Tl2) and Trinium2 (Tr2) fixtures. (Note: using this option on the Thallium2 eliminates the integral ballast option.) Clear Frost (CF) or White Frost (WF) are standard, but colored gels can be utilized to create custom color Lightstream accents. In addition, matching or two-tone metal accents can be used in lieu of an emissive lens. Please contact the factory or your local rep agency with any questions, color requests, or for specification assistance.
Flat (CPFT) Flat 4" diameter cover plate for use with a 3-O mud ring
Curved (CPCV) Curved 4" diameter Cover plate for use with a 3-O mud ring
Rb 2
Ra 2
R a 2- C S - R Tr2
Custom gel colors and other options are available. Please contact the factory with questions or specific requests.
Tl2
Lumium Lighting, LLC | 3820 Oceanic Dr., Suite 306, Oceanside, CA 92056 | Phone: 760.757.2530 | Fax: 760.283.2333 | www.lumiumlighting.com While we always strive to ensure all website content and product information is current, Lumium Lighting reserves the right to change specifications without notice. 2012 Lumium Lighting, LLC - All rights reserved.
Options-0813
OPTIONS GUIDE
O.3
GENERAL OPTIONS*
(continued)
*NOT ALL OPTIONS ARE AVAILABLE WITH EVERY FIXTURE *NOT ALL OPTIONS SHOWN
C A N O PY O P T I O NS STAN DARD
MAC H I N E D O PT I O N S
Canopies have several standard options as well as custom options to suit various environment aesthetics. The standard cable suspension system has 5” Satin White canopies. However, other standard options include a 2” non-power feed canopy option as well as no canopy at all. Both of these include a 5” diameter power feed canopy.
Machined canopies are 4” in diameter and can be anodized as well as powder caoted to match a desired color or they can be left with a mill finish for a more striking look. Similar non-power feed options are available with this aesthetic as well. These options do carry a higher cost than standard canopies, but also have an impressive appearance.
55
44
55 - 5” diameter power feed canopy and 5” diameter non-power feed canopy. Most common canopy layout. Creates a consistent ceiling aesthetic.
44
- 4” diameter machined power feed canopy and 4” diameter machined on-power feed canopy. Offers a consistent ceiling aesthetic with slightly smaller machined canopies. Mill, anodized, and powder coat finishes available.
52
41
52
- 5” diameter power feed canopy and 2” diameter non-power feed canopy. For a more minimal ceiling treatment while maintaining the ability to cover up mistakes. Requires a 1/4-20 stud securely fastened to ceiling.
41 - 4” diameter machined power feed canopy and 1-1/4” diameter machined non-power feed canopy. For a more minimal ceiling treatment while maintaining the ability to cover up mistakes. Requires a 1/4-20 stud securely fastened to ceiling. Mill, anodized, and powder coat finishes available.
50
40
50 - 5” diameter power feed canopy and no canopy on the non-power feed side. Minimal aesthetic. Requires a 1/4-20 stud securely attached to ceiling. Works well with conintuous runs where the power can be carried inside the fixture.
40 - 4” diameter machined power feed canopy and no canopy on the non-power feed side. Minimal aesthetic. Requires a 1/4-20 stud securely attached to ceiling. Works well with conintuous runs where the power can be carried inside the fixture. Mill, anodized, and powder coat finishes available.
CU S TO M C A N O P IE S Completely custom canopies can be ordered. These options are an upgrade, but can look spectaculare in certain applications. Contact the factory with all custom requests or with any questions. Custom Anodize (Machined Canopies only)
Custom Powder Coat
Custom Shapes
LENS OPTIONS Lumium has developed a unique Clear Frost (CF) polymer composite that maintains superb lumen transmission while limiting lamp imaging. White Frost (WF) lenses diminish and often eliminate lamp imaging while sacrificing only slightly reduced fixture efficacy. A choice of Clear Frost or White Frost lenses are available with all Lumium fixtures. Custom lenses are also available. Consult factory for all custom requests or with any questions.
Clear Frost (CF) Excellent light transmission Reduced lamp image
White Frost (WF) Minimal to no lamp image Slightly reduced efficacy
Lumium Lighting, LLC | 3820 Oceanic Dr., Suite 306, Oceanside, CA 92056 | Phone: 760.757.2530 | Fax: 760.283.2333 | www.lumiumlighting.com While we always strive to ensure all website content and product information is current, Lumium Lighting reserves the right to change specifications without notice. 2012 Lumium Lighting, LLC - All rights reserved.
Options-0813
Custom Custom colors and lens styles available - Consult factory
