Lexcom 15pos Assembly Guide

Transcript

15" Fanless POS system Assembly Guide 6G8881-2201-0100 Content 1-1 Specification ........................................................... 1 1-2 Package Content .................................................... 2 1-2.1 CD-ROM Package Content (option).................. 2 1-3 Exploded Drawing ................................................. 3 1-4 Assembly Procedure-RAM&HDD Installation ................................................................................... 4 1-5 Riser Card Installtaion .......................................... 5 1-6 CD-ROM & DVD-ROM Installation................11 1-7 Wireless Antenna Installation .............................13 1-8 Riser Card (RS005) Installation ........................ 18 15"Fanless POS system i 1-1 Specification Specification Chipset (a.) Intel 852GM/GME (b.) VIA CX700M (c.) VIA CN700 Processor (a.) Intel Pentium M/Celeron M-Dothan processor (b.) VIA V4 BUS Eden/C7 System memory 1 x DDR/DDR 2 memory, up to 1GB Storage Device* Support 2.5" HDD x 1 Support slim CD-ROM x 1(or PCI slot) Support CompactFlash Socket Support 40-pin IDE x 1 Support 44-pin IDE x 1 Dimension 15" panel: 31H x 376.2W x 313.5D mm Case: 55H x 319W x 254D mm Weight 5.3 kgs (lncl. M/B) Power specification AC100~240V (50/60Hz) Power supply Spec. _ 60W+5% *These storage devices can be optional combinations, depends on different motherboard. 1 1-2 Package Content (Fig.1) 1 15" POS Panel PC 5 Installation CD 2 Power Adapter 6 Screw set 3 Power Cord 7 HDD Cable 4 User's manual 8 Thermal Pad Fig. 1 9 HDD power cable 10 Rise Card(RS005) MV700A only 7 4 9 10 5 6 8 3 2 1 1-2.1 CD-ROM Package Content (option)(Fig.2) Fig. 2 1 CD-ROM 2 CD-ROM Adapter 3 CD-ROM Kit 1 2 3 5 4 1-2.2 CD-ROM Package Content (option)(Fig.2) 4 CD-ROM Cable 5 DC Cable 1-2.3 Wireless Package Content (option)(Fig.3) Fig. 3 1 2 3 Fig. 3 1 CD-ROM Kit 2 CD-ROM Cable 3 DC Cable 2 3 1 7 6 8 10 10.Mainboard 9.Inverter 8.Chassis 14.Wire Cover 7.Control Board 13.Back Cover 15.Back Cover (AL) 4.Touch Bracket 3.Touch Panel 2.Washer 9 11 1.Front Bezel Case Size : 376.6(W) x 313.5(D) x 104(H) mm Front Panel Size : 376.5(W) x 313.5(D) x 17.1(H) mm 2 3 4 5 11.H.D.D KIT 5.Panel 12 12.Rear panel housing 6.Panel Bracket 13 14 15 1-3 Exploded Drawing (Fig.1) 1-4 Assembly Procedure - RAM & HDD Installation (1.) Remove the 2 screws of wire cover, and then remove the wire cover.(Fig.4) (Fig.4) (2.) Remove the 4 screws of back cover, and then remove the back cover(AL).(Fig.5) (Fig.5) (3.) Remove back cover. (Fig.6) (Fig.6) 4 (4.) Remove HDD kit. (Fig.7) (5.) Install RAM into slot.(Fig.8) (Fig.7) (Fig.8) (6.) Install HDD cable. (Be cautions to the PIN1 orientation)(Fig.9) (Fig.9) 5 (7.) Install HDD to HDD kit, and then screw on the HDD kit (use M3x4 screw).(Fig.10)(Fig.10-1) (Fig.10) (Fig.10-1) (8.) Connect the HDD cable to HDD.(Fig.11) (Fig.11) (9.) Put HDD kit onto the back cover and then screw them together.(Fig.12) (Fig.12) 6 (10.) Place the Thermal pad to the bottom portion of the HDD for maximum contribution of heat transfer.(Fig.13) (Fig.13) (11.) Screw the back cover with the provided screws. (M3x8, M3x5, and M3x10).(Fig.14) (Fig.14) (Fig.14) 7 (12.) Secure the back cover(AL). (Attention: secure the 4 screws of both side first as illustrated).(Fig.15) (Fig.15) (13.) Screw the wire cover back to the system.(Fig.16) (Fig.16) 8 1-5 Riser Card Installation (1.) Remove PCI hold-down. (Fig.17) (Fig.17) (2.) Break the PCI retention bracket. (Fig.18) (Fig.18) (3.) Insert RS001 into the PCI slot. (Fig.19) (Fig.19) 9 (4.) Insert PCI card to RS001. (Fig.20) (Fig.20) (5.) Secure the PCI hold-down with the provided screw. (Fig.21) (Fig.21) (6.) Tighten the M3x4 screw. (Fig.22) (Fig.22) 10 1-6 CD-ROM & DVD-ROM Installation (1.) Insert CD-ROM cable. (Fig.23) (Fig.23) (2.) Insert DC power cable. (Fig.24) (Fig.24) (3.) Secure CD-ROM onto CD-ROM kit, by using the provided screws (M2x3). (Fig.25) (Fig.25) 11 (4.) Insert CD-ROM cable & DC power cable to the adaptor. (Fig.26) (Fig.26) (5.) Use the cable tie to sort surplus DC power cable. (Fig.27) (Fig.27) (6.) Secure the CD-ROM kit onto the system by using the provided screws (M3x4). (Fig.28) (Fig.28) 12 1-7 Wireless Antenna Installation (1.) Remove the 4 screws(M3*5) of the back cover(AL). (Fig.29) (Fig.29) (2.) Remove the 2 screws(M3*5) of the chassis. (Fig.30) (Fig.30) (3.) Remove all cables on the motherboard. (Fig.31) (Fig.31) 13 (4.) Remove 4 screws(M3*5) of the motherboard. (Fig.32) (Fig.32) (5.) Take out the motherboard and turn it around. (Fig.33) (Fig.33) (6.) Buckle the antenna cable onto the mini PCI(J1). (Fig.34) (Fig.34) 14 (7.) Install the mini PCI into socket. (Fig.35) (Fig.35) (8.) Put the motherboard back to the case. (Be cautious to the position of antenna cable) (Fig.36) (Fig.36) (9.) Secure the 4 screws(M3*5) of the motherboard. (Fig.37) (Fig.37) 15 (10.) Secure the 2 screws(M3*5) of the case. (Fig.38) (Fig.38) (11.) Insert all the cables back into the motherboard. (The touch cable must pass through the case hole and must not be bent.)(Fig.39) (Fig.39) (12.) Secure the 4 screws(M3*5) of the Case. (Fig.40) (Fig.40) 16 (13.) Install the cable into the case. (Fig.41)(Fig.42) (Fig.41) (Fig.42) 17 1-8 Riser Card(RS005) Installation (1.) Break the PCI retention bracket. (Fig.43) (Fig.43) (2.) Install RS005 into the slot. (Fig.44) (Fig.44) 18 (3.) Secure the PCI hold-down with the 2 round head screws(M3*4). (Fig.45) (Fig.45) (4.) Install PCI card into RS005. (Fig.46) (Fig.46) 19 (5.) Secure the PCI card with the PCI bracket. (Fig.47) (Fig.47) 20 Note. 15"Fanless POS system Assembly Guide 6G8881-2201-0100