Transcript
GRANDVIEW REPRODUCING GENUINE COLORS
Installation Guide for Large-flat Series Ultimate Permanent Cinema Screen
GRANDVIEW REPRODUCING GENUINE COLORS
Model：LF-PPxx
Grandview Crystal Screen Canada Ltd. #11- 3751 North Fraser Way, Marine Way Business Centre, Burnaby, BC, Canada V5J 5G4 Tel: 1-604-412-9777 Fax: 1-604-412-9796 Website: www.grandviewscreen.ca
Guangzhou Grandview Crystal Screen Co., Ltd. P.O. 511400 Federal Ind. Zone No. 363, Yushan West Road, Shiqiao, Panyu District, Guangzhou, Guangdong, China Tel: +8620-8489-9499 Fax: +8620-8480-3343 Website: www.grandviewscreen.com www.grandviewscreen.com.cn
Thank you for purchasing a Grandview projection screen. ISO9001:2000 International Certification
Before use, please read instructions carefully. After installation, store instructions for future reference.
Description Brackets
Side Frame Pieces Top and Bottom Frame Pieces
Fabric
Fixing Lug
1 Accessories 5x40 mm Screws with Anchors (8, not included)
Top and Bottom Frame Pieces (2pcs)
Fixing Lugs
Side Frame Pieces (2pcs)
Brackets
5x10mm Screws (8 pcs)
Top and Bottom Tension Bars (2pcs)
Side Tension Bars (2pcs)
Instruction Manual(1pc)
Corner Bra cke ts Scr ews (4 pcs)
Additional Sheet (Total Fixing Lugs Quantities) Format
Qty
92
100
106
120
150
180
4:3
pcs
\
28
\
32
38
44
\
16:9
pcs
24
28
28
30
38
44
48
※：Two More Fixing Lugs For Each Screen
200
Warnings
Installation
When installing, make sure it is facing forward. The back of the screen will be labeled with a sticker. Please read the following as any damage to the screen surface will affect the quality of the picture: 1.The frame is made with lightweight aluminum. Please handle with care. 2.Avoid contact or touching the screen surface as it may cause scratches or tears. 3.Do not write or draw on the surface. 4.Clean the screen with a soft cloth and lukewarm water. Do not use any detergent or cleaning products. 5.Use a cotton cloth to carefully wipe off the dust on the frame to prevent any damages 6.If it is not in use for a long period of time, cover the screen to shut out dust and dirt. To prevent unnecessary damage, the operating and maintenance of the screen should be done by adults.
5
Opening the case, the frame has indentations on surface because of packaging in a dry case for a long time. This is a normal phenomenon and the screen can be used normally. Please stay the screen in a normal condition that the indentations can be naturally removed. Recovery time will be changed in 1-15 days because of the air humidity, If you want to remove these indentations quickly, please use half-wet solution. Methods: Sprinkle water on the surface that can remove the indentations.
This projection screen should be installed at the best possible viewing position for the audience. Front projection (Figure 1) and Rear projection (Figure 2). Install according to material chosen.
Figure 1
Figure 2
1. Take out frame from box and lay on flat surface (Figure 3). Take out all additional parts.
2 Top and Bottom Frame Pieces
Side Frame Pieces
Ignoring the safety warnings may lead to injuries and/or damaging the product.
Fixtures should be installed in a secure place to avoid accidents or the screen falling.
Please contact your local dealer for repairs or maintenance. Please contact our company if you have any further questions. Avoid taking apart the fixtures yourself. Loose parts may cause the screen to fall.
Figure 3
2. Slide fixing lugs into grooves on reverse side of frame (Figure 4&5) and align with arrows (Note: Arrows are approximate).
Do not take apart and replace with unknown parts. If there are any problems, please contact your local dealer. Product specifications are subject to change. Fixing Lugs
Figure 4
Figure 5
3. Loosen corner bracket screws and slide into frame grooves. Carefully align frame corner to 90 degrees and fasten with screws. Repeat for each corner (Figure 6-7).
Aluminum corner connector piece
Top and Bottom Frame Pieces Side Frame Pieces
Figure 6
Figure 7
4. Unfold screen fabric and insert tension bars. Use the long bar for the top & bottom and the short bar for sides. Be careful not to poke the fabric (Figure 8-10).
6mm Tension Bars
8. Insert 6x12mm screws to fasten the brackets to the top and bottom frames. ( Figure 18- 1 9 )
Figure8 Figure18
3
4 Figure9
Figure10
5. Align fixing lugs with arrows. Using the tension bar, pull fabric eyelets over fixing lugs. Do top side first then rotate clockwise (Figure 11-15).
Figure11
Figure12 Figure19
Figure13
Figure14
Figure15
6. Adjust screen to ensure that it is flat and smooth. 7. Align brackets to desired width and measure. Drill two, or four holes (If using 4 brackets) in wall at measured width. Insert 5x40mm screws for studded wall, or 5x40mm screws + anchors for drywall without studs and hang (Figure 16-17).
Figure16
Figure17
