Transcript
© Copyright 2004. Black Box Corporation. All rights reserved. 1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746
SEPTEMBER 2004 LG9230CTX-32
Pure Networking 10/100/1000-Mbps PCI Bus Network Adapter
CUSTOMER SUPPORT INFORMATION Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500) FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018 Web site: www.blackbox.com • E-mail:
[email protected]
FCC AND IC RFI STATEMENTS FEDERAL COMMUNICATIONS COMMISSION and INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS
Class B Digital Device. This equipment has been tested and found to comply with the limits for a Class B computing device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or telephone reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver.
1
PURE NETWORKING 10/100/1000-MBPS PCI ADAPTER
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult an experienced radio/TV technician for help. CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
To meet FCC requirements, shielded cables and power cords are required to connect this device to a personal computer or other Class B certified device. This digital apparatus does not exceed the Class B limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of Industry Canada. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe B prescrites dans le Règlement sur le brouillage radioélectrique publié par Industrie Canada.
2
CE NOTICE EUROPEAN UNION DECLARATION OF CONFORMITY
This equipment complies with the requirements of the European EMC Directive 89/336/EEC.
3
PURE NETWORKING 10/100/1000-MBPS PCI ADAPTER Normas Oficiales Mexicanas (NOM) Electrical Safety Statement INSTRUCCIONES DE SEGURIDAD 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura. 3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser respetadas. 4. Todas las instrucciones de operación y uso deben ser seguidas. 5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc.. 6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean recomendados por el fabricante. 7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado por el fabricante. 8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser referido a personal de servicio calificado. 9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá, alfombra o superficie similar puede bloquea la ventilación, no se debe colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilación.
4
NOM STATEMENT 10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como radiadores, registros de calor, estufas u otros aparatos (incluyendo amplificadores) que producen calor. 11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en el instructivo de operación, o como se indique en el aparato. 12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada. 13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos, poniendo particular atención a los contactos y receptáculos donde salen del aparato. 14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones del fabricante. 15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de energia. 16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo. 17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilación. 18. Servicio por personal calificado deberá ser provisto cuando: A:
El cable de poder o el contacto ha sido dañado; u
B:
Objectos han caído o líquido ha sido derramado dentro del aparato; o
C:
El aparato ha sido expuesto a la lluvia; o
D:
El aparato parece no operar normalmente o muestra un cambio en su desempeño; o
E:
El aparato ha sido tirado o su cubierta ha sido dañada.
5
PURE NETWORKING 10/100/1000-MBPS PCI ADAPTER
TRADEMARKS USED IN THIS MANUAL IBM is a registered trademark of International Business Machines Corporation. Linux is a registered trademark of Linus Torvalds. Microsoft, Windows, and Windows NT are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. NetWare is a registered trademark, and ODI is a trademark, of Novell, Inc. UNIX is a registered trademark of UNIX System Laboratories, Inc. Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners.
6
CONTENTS
Contents 1.
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.1 Installing the Hardware. . . . . . . . . . . . . . . 12 3.2 Installing the Drivers . . . . . . . . . . . . . . . . . 12
4.
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 13 4.1 Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4.2 Calling Black Box. . . . . . . . . . . . . . . . . . . . 14 4.3 Shipping and Packaging . . . . . . . . . . . . . . 15
7
PURE NETWORKING 10/100/1000-MBPS PCI ADAPTER
1. Specifications Standards: IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3ab 1000BASE-T, IEEE 802.3x Topology: Star Speed: 10-Mbps half-duplex/20-Mbps full-duplex; 100-Mbps half-duplex/200-Mbps full-duplex; 1000-Mbps full-duplex Hardware Required: IBM® compatible PC with available PC slot (PCI 2.2), 32-bit, 66/33-MHz Drivers Included: Windows® 98/98 SE/Me/XP, Windows 2000, and Windows NT®, NetWare® Server 4.x/5.x/6.x, NetWare ODI™ for DOS, Linux®, UNIX® Compliance: FCC Class B, CE Mark, C-tick, VCCI IRQ Line: Assigned by system I/O Address: Assigned by system Connectors: (1) RJ-45 Indicators: (1) Link/Activity LED 8
CHAPTER 1: Specifications
Temperature Tolerance: 32 to 131°F (0 to 55°C) Relative Humidity: Up to 95%, noncondensing Power: From the interface Size: 4.7"H x 1.6"W (11.9 x 4.1 cm)
9
PURE NETWORKING 10/100/1000-MBPS PCI ADAPTER
2. Overview The Pure Networking 10/100/1000-Mbps PCI Bus Network Adapter connects an IBM compatible PC to an Ethernet network. (It fits in a PCI slot of your computer.) The adapter complies with the 32-bit PCI specification and supports half-/full-duplex operation, which can double network speed. The adapter supports 1000 Mbps (Gigabit), 100 Mbps, and 10 Mbps network speeds. 1000BASE-T operates on all four pairs of Category 5 UTP cable. 100BASE-TX operates on two pairs of the CAT5 cable, and 10BASE-T operates on two pairs of Category 3, 4, or 5 UTP cable. With autonegotiation technology, network speed is autodetected. When you connect the adapter to a Gigabit switch or to another Gigabit NIC, full Gigabit speed will be attained. If you connect the adapter to a 100BASE-TX hub, the network speed is 100 Mbps. If the hub is a switching hub that supports full-duplex function, then the speed will be doubled to 200 Mbps. A variety of drivers are supplied with the adapter, including Microsoft® Windows 98, 98 SE, Me, XP, Windows 2000, and Windows NT, NetWare Server 4.x/5.x/6.x, NetWare ODI for DOS, Linux, and UNIX. 10
CHAPTER 2: Overview
The adapter supports 32-bit operation. It complies with the 66-/33-MHz PCI Local Bus Master Version 2.2 and the IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, and IEEE 802.3x standards. The adapter features IEEE 802.3x full-duplex flow control and IEEE 802.1Q VLAN tagging. It also offers Wake On LAN power management and Jumbo Frame, as well as plug-and-play installation, auto-setup IRQ, and I/O address. The adapter autonegotiates for full- or half-duplex operation.
What’s Included Your package should include the following items. If anything is missing or damaged, please contact Black Box at 724-746-5500. • (1) Pure Networking 10/100/1000-Mbps PCI Bus Network Adapter • (1) CD-ROM containing software drivers and this users’ manual in PDF format
11
PURE NETWORKING 10/100/1000-MBPS PCI ADAPTER
3. Installation 3.1 Installing the Hardware To install the adapter in your PC, follow these steps: 1. Power off the computer and remove its cover. 2. Insert the adapter into a PCI slot. 3. Secure the adapter to the rear of the computer chassis and replace the computer cover. 4. Connect the adapter to the network using twisted-pair cable. 5. Power on the computer.
3.2 Installing the Drivers Use the drivers included with the product. For details, go to the readme.exe file in the root directory of the included CD-ROM.
12
CHAPTER 4: Troubleshooting
4. Troubleshooting 4.1 Indicators If you experience any problems with the adapter, please make sure the appropriate driver is loaded, the proper cable is connected to the adapter port, and the hub/switch complies with the adapter specification (such as 10-Mbps 10BASE-T, 100-Mbps 100BASE-TX, and 1000-Mbps 1000BASE-T), then check the LEDs. The Speed LED indicates that the adapter is connected to a 10BASE-T, 100BASE-TX, or 1000BASE-T network. When the LED is off, the adapter is connected to a 10BASE-T network. When the light is amber, the adapter is connected to a 100BASE-TX network. When the LED is green, the adapter is connected to a 1000BASE-T network. The Link/Activity LED, when off, indicates that the UTP port has not been connected or the link is not OK. When the LED is on, the UTP port link is OK. When the LED is blinking, there is traffic flow on the network that the adapter is connected to.
13
PURE NETWORKING 10/100/1000-MBPS PCI ADAPTER
4.2 Calling Black Box If you determine that your adapter is malfunctioning, do not attempt to alter or repair the unit. It contains no user-serviceable parts. Contact Black Box at 724-7465500. Before you do, make a record of the history of the problem. We will be able to provide more efficient and accurate assistance if you have a complete description, including: • the nature and duration of the problem. • when the problem occurs. • the components involved in the problem. • any particular application that, when used, appears to create the problem or make it worse.
14
CHAPTER 4: Troubleshooting
4.3 Shipping and Packaging If you need to transport or ship your adapter: • Package it carefully. We recommend that you use the original container. • If you are shipping the adapter for repair, make sure you include everything that came in the original package. Before you ship, contact Black Box to get a Return Authorization (RA) number.
15
