Transcript
OPERATION (Continued)
LHP100GK 2.4GHz Smart Camera 2.1 The LHP100GK is a 2.4GHz IR Surveillance Camera which can be installed indoors or outdoors. The 2.4GHz wire free camera module will transmit audio/video signals to the host LHK110EK 7” Touch Panel receiver for monitoring and recording purposes. The host LHK110EK can pair with and control devices such as 2.4GHz IR cameras, wire free O-net Security devices, and On/Off Plugs. Please see your LHK110EK Instruction Manual for details.
2. Pairing Button The pairing button on the IR camera power input cable is used to pair the camera with the host LHK110EK. 3. 3.1
3.2
3.3
4.
INTRODUCTION The LHP100GK features multiple IR LED’s that activate at night (or low light levels) to ensure a sharper image. The built in microphone transmits sound to the host LHK110EK. Status LED’s, green and red indicate day or night mode.
ID Code Learning Put the host LHK110EK into the “Pairing” screen for IR Camera (From “Standby” mode, tap “Setting (Camera)”, select Camera number and IR Camera, then tap “Pair”). Press the Pairing Button on the IR Camera to pair the devices. When pairing is complete, a “Pairing Successful” screen will appear on the LHK110EK and it will automatically link to the camera. The user may now switch to the camera view to confirm if the linking and pairing was successful. If “Pairing Failed” appears, please repeat steps 3.1 and 3.2. Note the devices only remain in pairing mode for 30 seconds. Please see your LHK110EK Instruction Manual for more information. Video / Audio Functions Under normal operating conditions, the LHP100GK Camera image can be viewed from the host LHK110EK or via your smart device. If the LHK110EK system is triggered by a security device paired on the system (PIR, Magnetic Contact etc.) the LHP100GK will be activated and begin transmission of video / audio signals in H.264 format via 2.4GHz wire free signal to the LHK110EK.
INSTALLATION 1. In order to ensure correct function do not install the camera near a heat source or where direct sunlight will shine into the camera lens. Avoid high humidity areas eg. bathrooms or kitchen areas where steam may ‘fog’ the camera lens. Do not mount the camera on or near metalwork since this can block the camera signals.
OPERATION 1. Status LEDs 1.1 Plug the supplied AC adaptor into an AC socket, and then plug the DC jack into the IR camera cable. The green LED will illuminate when the power supply is normal and the camera is in day mode. 1.2 The red LED will illuminate when the light level is low, indicating that the IR LED’s are active and the camera is in night mode.
2. The camera may be used indoors or outdoors. The camera cable DC jack plug / socket is designed to be weather proof. Ensure the DC jack plug / socket is pushed fully home to avoid moisture ingress.
1
SPECIFICATIONS (Continued)
INSTALLATION (Continued)
Camera & Audio / Visual Transmissions White Balance Automatic Auto Gain Control (AGC) Automatic Backlight Compensation Automatic Signal to Noise Ratio (SNR) > 48 dB Gamma Compensation 0.45 Electric Shutter Automatic Lens Viewing Angle Horizontal: 48° / Vertical: 36° Audio Format One Way, 8K Pulse Code Modulation IR LED 28 x 850nm IR CUT Yes Protection Degree IP65 Mounting Height / Surface Recommended minimum 2m. Standard London brick wall Power Requirement AC 100-240V / 50-60Hz Adaptor DC5V 1A RF Frequency 2.4Ghz RF Modulation Gaussian frequency-shift keying (GFSK) Spread Spectrum Frequency hopping Transmission Range Approximately 100m in free air Camera numbers Maximum 4 cameras per host LHP100GK
3. The camera should be installed as shown in Figure 1 below, with the sliding top cover positioned as shown. The aerial should be pointing upwards. An installation height of at least 2m is recommended. Use the plugs and screws supplied to fix the camera to a standard brick wall. 4.
Environment: -10°C to 50°C, 20-85% Humidity.
Figure 1 TROUBLESHOOTING Symptom Green LED does not illuminate when the LHP100GK is powered on.
Recommendation 1. The AC adaptor or the DC jack is not plugged in correctly.
Transmitted videos erratic or unclear.
1. 2.
are
Specifications are subject to change without notice
LUXHOMELHP100GK 2015/06
Ensure the 2.4G aerial is correctly fitted and tight. The distance between the camera and host is too great, reduce the distance.
Environmental Concerns:
SPECIFICATIONS Camera & Audio / Visual Transmissions Camera Sensor 1/4” CMOS OV7725 Night Vision Range Maximum 15m in low light level (about 1 Lux) Microphone Built-in Operating Temperature / -10°C to 50°C. Maximum 85% relative humidity, Humidity Range non-condensation Pixel 640 x 480 VGA Video Compression H.264 Resolution (with 7” Monitor) 1 to 1: H.264 - 480 x 272 / 30fps
Please DO NOT dispose of electrical appliances as unsorted waste, use the recycling facilities provided by your local authorities. Please DO NOT dispose of packaging as unsorted waste, use the recycling facilities provided by your local authorities.
2
