Transcript
Lisa Cot Bed IMPORTANT PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT KEEP FOR FUTURE REFERENCE
www.obaby.co.uk
www.obaby.co.uk
Thank you for choosing O Baby. To ensure that your cot bed is used in accordance with these instructions, please read them fully and retain for future reference. If you have any problems please contact O Baby -
[email protected] or 0845 078 0290 BEFORE ASSEMBLY - Unpack all the parts and identify them against the fittings and components lists. - Do not discard any packing until you are sure you have all the parts and the pack of fittings - If you do not find the missing parts or if you find any damages call the O Baby helpline 0845 078 0290 - Read the instructions thoroughly before attempting to construct the cot/cot bed. - You may find the construction of your cot/bed easier if you have the help of another person. - Follow each stage of construction step-by-step. - It may be unsafe to use replacement part or accessories
Page One
www.obaby.co.uk
Parts A. Allen key x 1 B. Long assembly screw x 8 C. Short assembly screw x 8 D. Barrel nuts x 16
D
A B
C
Cot bed head end & Foot end panel (Foot end has the O Baby logo facing the outside of the cotbed)
Cot bed base
Fixed sides x 2
Page Two
www.obaby.co.uk
Assembling your cot bed Top Tip! don’t tighten all the screws fully until you have completed assembling. Step 1 Starting on one end of the base fit the barrel nuts in the holes provided on the base corners . Ensure the slits are facing the inside of the base.
Step 2 Decide how high you would like your base; - For a new born - to make it easier for the parent the base can be at its highest. - Once the child can start to sit up unaided you should lower the base to prevent the baby climbing out or over the rails. Once you have decided what level you are fitting the base, fit the long screws in the 2 holes in the base Highest level for new borns until they can sit up unaided Middle Level for babies sitting up until they are standing/climbing Lowest Level for babies that can stand
Step 3 Using your allen key & the long screws fit the base to the first end & then fit the other end the same way. 2 x long screws per side (8 in totaly for the base).
Page Three
www.obaby.co.uk
Assembling your cot bed Step 4 Now add the first side rail, starting by attaching the tops first. Put the barrel nut in the side rail, then thread the long screw through the cot end & then through the rail and tighten it up into the barrel nut. Do this on the other end of this rail
Step 5 Now do the same but for the bottom of the side panels.
Step 6 Now go around the whole cot bed and tighten every screw completely.
Page Four
www.obaby.co.uk
Changing the Cot into a Junior Bed Only change into a Junior bed when your are confident that you child will be safe without the side rails.
Step 1 Remove both side rails using the allen key.
Step 2 Fit the base to the lowest level using the same fittings for the base that were used for the Cot.
Step 3 Tighten all the screws properly.
Page Five
www.obaby.co.uk
www.obaby.co.uk
INSTRUCTIONS FOR SAFE USE & MAINTENANCE READ CAREFULLY BEFORE USING THIS PRODUCTS & KEEP FOR FUTURE REFERENCE. - The lowest position for the cot base is the safest. This position should always be used once the baby is old enough to sit up. - Never leave anything in the cot which could provide a foothold for your child to climb out or would present a danger of suffocation or strangulation. - All assembly fittings should be tightened properly and care should be taken to ensure that no screws are loose, a child could trap parts of the body, or clothing (e.g. ribbons, drawstrings, necklaces this could pose strangulation. - Regually check that all fittings and components of the cot/bed are fully tightened and in working order. If any parts have become worn or damaged then do not use the cot/bed, seek advice from your retailer or contact O Baby’s Customer Care -
[email protected] or 0845 078 0290. - Do not use replacement parts that are not recommended or supplied by O Baby. Non approved parts may render the cot/bed unsafe or may be considered product damage or misuse, voiding the warranty. - Do not place you cot/bed in the close proximity of an open fire and other sources of heat, such as radiators, electric or gas fires. - We recommend you use the O Baby Mattress Size 140 x 69cm for this Cot Bed. - The mattress should be no more then 40mm shorter or narrower than the internal length or width of the cot/bed. - The thickness of the mattress chosen should be such that the distance between the surface of the mattress to the upper edge of the cot sides is a minimum of 500mm when the base is set in the lowest position and a minimum of 200mm when the cot base is set in the highest position. - Your cot/bed may be cleaned with a damp cloth. Never use bleach or harsh abrasives. - Due to constant updating and improvements, some components may occasionally differ slightly from diagrams shown in these instructions. We reserve the right to change the specifications of any products without prior notice. Safe Use & Maintenance Page
