Transcript
Parts Monitor
Splitter cable
Mounting bracket
Air antenna
Ground antennas (2)
Video transmitter
GoPro video cable
LiveView™ Kit for GoPro Mounting velcro
User Guide
Transmitter Assembly
GoPro HERO Assembly
Attach a velcro strip to the flat side of the video transmitter to prepare it to mount to the copter. Connect the air antenna (red) to the transmitter.
For X8+, use the GoPro video cable pre-installed onto the vehicle. For other vehicles, use the GoPro video cable provided with this kit.
The transmitter has two ports: a two-wire port and a three-wire port. Connect the black connector on the splitter cable to the transmitter’s two-wire port. The transmitter’s three-wire port will connect to the GoPro video cable. On the end of the GoPro video cable with two connectors, select the connector with the more widely-set wires. Orient the connector with the metal pins facing in the same direction as the velcro, and connect to the transmitter’s three-wire port.
Connect the micro-USB end of the cable to the GoPro’s micro-USB port.
GoPro video cable to GoPro HERO wiring
Select the connector with the larger space between the two wires.
Insert the mounting screw provided with the cable through the cable plate and attach to the hole in the gimbal marked below. This will secure the cable to the gimbal.
GoPro video cable
Antenna
Secure cable to gimbal
Splitter cable GoPro video cable Complete transmitter wiring
!
Important note: Make sure that the WiFi on your GoPro is turned OFF at all times when in use with your copter. The WiFi signal can interfere with the copter’s radio communication and cause unexpected behavior.
IRIS+ Mounting Choose a position on the shell to mount the video transmitter, and attach the second piece of velcro there. You can mount the transmitter anywhere on the shell where it will not obstruct the propellers or interfere with the battery door. We recommend placing it between the gimbal interface place and the battery door; make sure to place it close enough to the gimbal plate so that the battery door can fully open.
1 2 Splitter cable
Locate the gimbal power cable on the underside of IRIS, and disconnect the two red connectors. This is where you will connect the splitter cable to power both the gimbal and the video transmitter off the flight battery.
3 IRIS, video transmitter, and gimbal: complete wiring
IRIS LiveView complete assembly
X8+ Mounting
IRIS: Disconnect gimbal power cable
Recommended placement of mounting velcro on IRIS
Attach the second piece of velcro in front of the Pixhawk where the video transmitter can connect to both the power and GoPro video cables. Connect the red connector on the X8 to the larger red connector on the splitter cable. (The splitter cable’s smaller red connector will remain unconnected.) Secure the two velcro strips together.
Connect the splitter cable to both red connectors. The splitter cable should now be connected to (1) the red connector on the gimbal power cable, (2) the red connector on the IRIS power cable, and (3) the video transmitter. Secure the two velcro strips together.
X8 and video transmitter: complete wiring
X8 and video transmitter: complete assembly
Monitor Assembly
Operation
The monitor mounting bracket includes extra parts for attaching to different controllers.
Power the copter, controller, gimbal, and GoPro normally. Press and hold the power button to turn on the monitor.
Use for this assembly.
Extra parts
Mounting bracket parts Power
Insert the larger black screw into the hinge between the two silver parts. Then position the bracket over the neck-strap attachment on the controller, and insert the smaller black screw.
Mode
Down
Up
Minus
Plus
Monitor
To configure the monitor, set the mode to DIV (M button changes modes), the channel to 8 (+ and - buttons), and the band to E (press the power button to access the menu, the M button to advance within the menu, and the up and down arrow buttons to make individual selections).
(2.5 mm hex key)
Video Transmitter Specs (2 mm hex key)
Controller and mounting bracket assembly
Complete controller and monitor assembly
Add both ground antennas (blue) to the monitor. Add the black washer to the silver screw, and attach the monitor to the bracket.
»» »» »» »» »» »» »» »» »» »» »»
5.8 GHz 200 mW wireless AV transmitter: Transmitter frequency / channel amount: 5705-5945 MHz / 8 CH Output power: 200 mW/33 dBm Frequency control: Built-in frequency & phase lock loop AV input: analog AV signal input ANT connector: RP-SMA Power supply: DC 7-12 volts Current supply: 850 mA Size: 68*26*28 mm Weight: 60 g (including antenna) Gross weight: 85 g LiveView Kit for GoPro User Guide vA | DCT0039 | ©3D Robotics, Inc. | 21 November 2014
