Transcript
Livezi Central
4 speed fan Control System
Operating Instructions
2
1
Operating Instructions
The following pages detail the operation of the various control system types available for the Livezi ducted systems.
1.1
Livezi Central Controller (single zone)1
1.1.1 Touchpad layout
Liquid Crystal Display screen with scrolling system status.
Adjust setpoint, scroll through options and change variables.
22.5 °c T A Mode=Aut
Access parameter adjustment. Save variables and advance to next field.
Adjust indoor fan speed.
SET
ZONE Turn system on and off.
MODE
CLOCK Adjust the current time or program.
Access mode selection screen.
Adjust setpoint, scroll through options and change variables.
1.1.2 Turning the system on or off 1. Press
to turn the system on or off as required.
When the system is off the display appears like this.
L iv e z i A O ff
(Livezi Air Conditioning scrolls across the top line). When the system is on the following information is displayed.
Setpoint
Operating Mode
Conditioning Mode
T = Timer program R = Run timer
A = Auto C = Cool H = Heat v = Vent
Upper Case indicates compressor is energised.
22.5°c R A
L o ad= 3 0 %
Scrolling System Status
Mode=Auto
Load=85%
Fan=900L/s
Temp=23.0 Status=Cooling
1.1.2 Selecting the conditioning mode 1. Press
MODE to access the mode selection screen.
M o de = A u to
2. Use 3. Press
or
to select the required mode (select from Auto, Cool, Heat or Vent).
SET to save and exit.
1.1.3 Adjusting the indoor fan speed 1. Press
FAN
to access the fan speed adjustment screen.
Fan s p e e d =10 0 %
2. Press
or
to increase or decrease the fan speed setting (adjustable from 100% to
30% in 10% steps). 3. Press
SET to save and exit.
3
4
1.1.4 Setting the required temperature (setpoint) 1. Press
or
or
SET to access the setpoint adjustment screen.
Set=2 2 .5 °c Tmp=2 3 .0 °c
2. Use 3. Press
or
to adjust the set point to the desired level.
SET to save and exit.
1.1.5 Setting the run timer The run timer is activated when the system is turned on manually. The timer begins counting down from the set value and turns the system off when the run timer period has expired. To disable the run timer set it to --:--Hrs. 1. Press and hold
SET for ≈ 10 seconds to access the run timer screen.
R u nTi m e r - - :- - H rs
2. Use 3. Press
or
to alter the value in 10 minute increments.
SET to save and exit.
1.1.6 Clock Functions The optional clock module must be installed to enable the clock functions. These are then accessible via the clock display screen. 1. Press
1 0 :12 p Tu 0 2 O c t ,0 7
2. Press
clock to view the clock display screen.
SET to enter the clock menu screen.
™ e tClo c k S S e tP ro g s
3. Use
or
to cycle the cursor to the desired menu option, then press
SET to access
the edit screen for that option.
1.1.7 Setting the clock 1. Select SetClock from the clock menu, then press
SET to edit the system time.
1™ 0 :1 2 a m 0 2 O c t ,0 7
2. The cursor will highlight the Hour value. Use for am/pm), then press
or
to select the correct hour (watch
SET.
3. Repeat this procedure for the Minutes, Day, Month and Year values. 4. After pressing
SET to accept the Year, the display will return to the clock display screen.
1.1.8 Setting the timer programs Active Programs will appear in CAPITALS (PROG 02 = active; prog 02 = not active) To disable a timer program, select a start & stop time of --:--, or make all days inactive. 1. Select SetProgs from the clock menu, press SET to access the timer program selection screen.
™ROG 02 P p ro g 0 3
2. Use
to select the timer program to be edited, then press SET to edit the start time.
or
The cursor will highlight the minutes value.
S ta r t: 0 8 :4 ™ 0 am
3. Use
to select the correct time in 10 minute increments, then press SET to edit
or
the stop time.
S to p: 0 5 :3 ™ 0 pm
4. Use
or
to set the stop time then press
SET to access the run day selection
screen. The cursor will highlight the first letter on the bottom line, representing Sunday.
A /C D a y s ™MTWTFS s
5. Press the or
to turn this program on (S is upper case),
to turn the program off (s is lower case) for this day.
SET to save and move the cursor to the next day. 7. Press CLOCK to go back if required. 6. Press
8. Repeat this procedure for each day of the week. 9. Press SET at Saturday to save the program and return the display to the program selection screen. Use 10. Use
or
or
to select another program and repeat the process.
to navigate to the Exit option and press
SET when finished.
1.1.9 Setting holidays Active Holidays will cause the system to ignore timer program signals. Holidays may be set as single days, or as blocks. Dates are inclusive. For a one day holiday, enter the same start and stop date. All holiday programs must have a start and stop date to be valid. To disable a holiday program, set it’s start or stop date to -----. Active Holidays will appear in CAPITALS (HOL 02 = active; hol 02 = not active) 1. Select Set Hols from the clock menu screen then press
SET to display the holiday
program selection screen.
™OL H h ol
02 03
5
6
2. Use
or
to select the Holiday program to be edited, then press
SET. The cursor will
highlight the Month value.
S ta r t: De™ c 31
SET.
3. Use
or
to select the correct Month, then press
4. Use
or
to select the correct Day, then press SET. The display will change to the stop
date screen.
S to p: Ja ™ n 02
5. Repeat the procedure to set the stop date for the holiday. 6. The display will revert to the holiday selection screen and the cursor will highlight the last holiday edited. Use 7. Use
or
or
to select another program and repeat the process.
to navigate to the Exit option and press
SET when finished.
1.1.10 Daylight savings The daylight savings function advances the clock’s time by 1 hour whilst the current date and time are between the start and stop dates set. To disable daylight savings, simply select a start date of -----. (Typically: Southern Hemisphere = Oct 31...Mar 31; Northern Hemisphere = Mar 31...Oct 31) 1. Select Day Save from the clock menu screen, then press SET to select the start date for daylight savings. The cursor will highlight the Month value.
S ta r t: O c™ t 31
SET.
2. Use
or
to select the correct Month, then press
3. Use
or
to select the correct Day, then press SET. The display will change to the stop
date screen.
S to p: M a™ r 31
4. Repeat the procedure to set the stop date for daylight savings. When finished the display will revert to the clock menu screen. Note: The 1 hour advance occurs at 1:59 am (advances to 3:00 am) and the 1 hour revert occurs at 2:59 am (reverts to 2:00 am).
Notes
Livezi Phone 1300 306 125 Fax 07 3890 8734 Web: www.livezi.com.au Email:
[email protected]
