Transcript
IEXT224-4PH-L IEXT224-4PH-R Long Reach POE Extenders
1
LEGAL The information in this publication has been carefully checked and is believed to be entirely accurate at the time of publication. CTC Union Technologies assumes no responsibility, however, for possible errors or omissions, or for any consequences resulting from the use of the information contained herein. CTC Union Technologies reserves the right to make changes in its products or product specifications with the intent to improve function or design at any time and without notice and is not required to update this documentation to reflect such changes. CTC Union Technologies makes no warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does CTC Union assume any liability arising out of the application or use of any product and specifically disclaims any and all liability, including without limitation any consequential or incidental damages. CTC Union products are not designed, intended, or authorized for use in systems or applications intended to support or sustain life, or for any other application in which the failure of the product could create a situation where personal injury or death may occur. Should the Buyer purchase or use a CTC Union product for any such unintended or unauthorized application, the Buyer shall indemnify and hold CTC Union Technologies and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, expenses, and reasonable attorney fees arising out of, either directly or indirectly, any claim of personal injury or death that may be associated with such unintended or unauthorized use, even if such claim alleges that CTC Union Technologies was negligent regarding the design or manufacture of said product. WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference in which case the user will be required to correct the interference at his own expense. NOTICE: (1) The changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. (2) Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. CISPR PUB.22 Class A COMPLIANCE: This device complies with EMC directive of the European Community and meets or exceeds the following technical standard. EN 55022 - Limits and Methods of Measurement of Radio Interference Characteristics of Information Technology Equipment. This device complies with CISPR Class A. WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. CE NOTICE Marking by the symbol CE indicates compliance of this equipment to the EMC directive of the European Community. Such marking is indicative that this equipment meets or exceeds the following technical standards: EN 55022:2006+A1:2007, Class A, EN55024:2010, and EN60950-1:2006
2
CTC Union Technologies Co., Ltd. Far Eastern Vienna Technology Center (Neihu Technology Park) 8F, No. 60, Zhouzi St. Neihu, Taipei, 114 Taiwan Phone: +886-2-2659-1021 FAX: +886-2-2799-1355 IEXT224-4PH-L IEXT224-4PH-R Long Reach PoE Extenders User Manual Version 1.0 July 2015
This document is the current official release manual. Contents are subject to change without prior notice. Please check CTC Union's website for any updated manual or contact us by E-mail at
[email protected]. Please address any comments for improving this manual or to point out omissions or errors to
[email protected]. Thank you. 2015 CTC Union Technologies Co.,Ltd. All Rights Reserved The contents of this document are subject to change without any prior notice.
3
Table of Contents 1. PRODUCT INTRODUCTION .............................................................................................................. 5 1.1 DESCRIPTION...................................................................................................................................... 5 1.2 FEATURES .......................................................................................................................................... 5 1.3 SPECIFICATIONS .................................................................................................................................. 6 1.4 APPLICATIONS .................................................................................................................................... 7 1.5 REFERENCE PERFORMANCE DATA ........................................................................................................... 8 2. HW DESCRIPTION ........................................................................................................................... 9 2.1 OVERVIEW ......................................................................................................................................... 9 2.2 PRODUCT OUTLOOK ............................................................................................................................ 9 2.3 LED DEFINITION ............................................................................................................................... 10 2.4 POWER ........................................................................................................................................... 11 2.5 3-POSITION DIP SWITCH .................................................................................................................... 12 3. REGULATORY COMPLIANCE .......................................................................................................... 13
1. Product Introduction 1.1 Description IEXT224-4PH-L & IEXT224-4PH-R Long Reach POE Extenders are designed to extend the reach of Ethernet Data and IEEE 802.3at Power over Ethernet beyond its natural limitations of 100 m for the network infrastructure. The solution works in pairs for point to point connectivity. It features IEXT224-4PH-L Long Reach PoE Extender (CO), the master unit at the central site that can transmit data and power over a single pair of telephone grade UTP wire up to 1,200 m or coaxial cable up to 1,800 m. On the receiving end is IEXT224-4PH-R Long Reach PoE Extender with 4 PoE (PSE) ports (CPE). Without the need for local power supply, each IEXT224-4PH-R is equipped with four 10/100Base-TX IEEE 802.3at POE Ports for total power budget of 30W that can support any remote IEEE 802.3at/af powered device (PD) like Wi-Fi Access Point, IP phone, and IP Camera. It enables centralized management of power supply from a single location for easy, efficient and cost- effective installation. When enabling local power supply by dip switch, IEXT224-4PH-R can supply power budget of 30W to each one of the four POE ports. IEXT224-4PH-L & IEXT224-4PH-R Long Reach PoE Extenders are an ideal POE extension solution for service providers to deploy networking applications in public areas that requires Wireless AP, IP Phones and IP Cameras.
1.2 Features
Complies to IEEEE 802.3at POE Industrial-Grade Extenders for applications in harsh environment Simultaneous transmission of Ethernet data and POE Power over UTP wire Centralized management of power supply Eliminated the need for local power supply at remote sites Easy cabling for quick installation Long transmission distance up to 1000 m Quick deployment and easy maintenance. Flexible and efficient power management Automatically switch between VDSL2 Profile 30a and 17a to utilize bandwidth performance Dip Switch to enable local power supply and provide full 30W to each of the four POE ports.
5
1.3 Specifications Standards Support:
Hardware Interfaces: Terminal Block for Copper Port
VDSL2 ITU-T G.993.2
BNC Female for Coaxial Port
VDSL2 Profiles: 17a and 30a
4 x RJ-45 10/100Base-TX IEEE 802.3at POE Protocol Support
Port
Transparent bridging to higher layer protocols
3 Position Dip Switch Operating Environment
Selectable target band plan (Asymmetric or
Operating Temperature: -40°C to 75°C
Symmetric) Selectable target SNR margin (6dB or 9dB)
Storage Temperature: -40°C to 85°C
Selectable Remote Power (ON) or Local Power
Humidity: 10% - 95% (non-condensing)
(OFF)
Physical Hardened aluminum case, IP30
LED Indicators: Active: System Status
Dimensions: 62 x 135 x 106.5 mm
LPWR/RPWR: Local Power/Remote Power
Installation: DIN-Rail, Panel Rack Mounting
POE: POE Port Status
Regulatory Compliance
Available POE Output(Watts): 5/15/30
CE
Line Speed(Mbps): Link/20/40/60/80/100
FCC Part 15 Class B EN60950
Power Supply: Terminal blocks for redundant DC power inputs Din connector for external AC to DC adaptor Input Voltage: 48 to 57 VDC Power Consumption: 65 Watts maximum Over current protection Automatic short protection
6
1.4 Applications The solution works in pairs for point to point connectivity. It features IEXT224-4PH-L Long Reach PoE Extender (CO), the master unit at the central site that can transmit data and power over a single pair of telephone grade UTP wire up to 1,200m or coaxial cable up to 1,800 m. On the receiving end is IEXT224-4PH-R Long Reach PoE Extender with 4 PoE(PSE) ports (CPE). Without the need for local power supply, each IEXT224-4PH-R is equipped with four 10/100Base-TX IEEE 802.3at POE Ports for total power budget of 30W that can support any remote IEEE 802.3at/af powered device (PD) like Wi-Fi Access Point, IP Phone, and IP Camera.
Picture 1.1 Remote Power Enable
Picture 1.2 Remote Power Disable
7
1.5 Reference Performance Data UTP – 24AWG Copper Wire SNR
6dB
6dB
Profile
Asymmetrical
Symmetrical
Upstream Line Rate (Mbps)
Downstream Line Rate (Mbps)
Upstream Line Rate (Mbps)
300 m
65
100
100
100
30 W
400 m
45
95
70
70
20 W
600 m
30
65
45
45
15 W
800 m
10
45
27
27
7W
1,000 m
6
35
18
18
5W
1,200 m
1
20
8
16
4W
Distance
Downstream Line Rate POE output power (Mbps)
Coaxial Cable SNR
6dB
6dB
Profile
Asymmetrical
Symmetrical
Upstream Line Rate (Mbps)
Downstream Line Rate (Mbps)
Upstream Line Rate (Mbps)
400 m
100
100
100
100
30 W
600 m
50
100
50
80
20 W
800 m
50
100
50
80
15 W
1000 m
45
90
50
60
10 W
1,200 m
40
70
50
50
8W
1,400 m
35
55
40
35
6W
1,600 m
30
40
35
30
5W
1,800 m
10
35
20
20
4W
2,000 m
5
30
15
15
Distance
8
Downstream Line Rate POE output power (Mbps)
2. HW Description 2.1 Overview IEXT224-4PH-L & IEXT224-4PH-R devices are Long Reach POE Extenders with four
10/100Base-TX IEEE 802.3at POE Ports. This chapter shows the product outlook and Hardware interfaces.
2.2 Product Outlook
CO Faceplate
CPE Faceplate
9
2.3 LED Definition The LED indicators could provide instant feedback to users; the behaviors of the LED are given in below table: LED Name Local PWR Remote PWR POE (CPE)
Link
Indicator/Color
Condition
Green-off
No local input power
Green-on
Local input power received
Green-off
No power is transmitted over VDSL interface
Green-on
Power is transmitted over VDSL interface
Green-off
No power is transmitted over Ethernet port
Green-on
Power is transmitted over Ethernet port
Green-off
VDSL link not link up
slow flashing
VDSL port is under handshaking
Fast flashing
VDSL port has data transmission or reviving
Green-on
VDSL port link up
Green-on
Displays VDSL link speed in Mbps (100M/80M/60M/40M/20M), if 80M LED is on then VDSL downstream line speed is in the
Line Speed
range 80Mbps to 100Mbps. POE Output (CPE)
RJ-45
Green-on
Displays POE PSE available output power in Watt(30W/15W/5W) – Remote Terminal Only
Green-on
Ethernet link up and speed is 100M
Green-flashing
Data transmission or receiving
Green-off
Ethernet is no link up
Yellow-on
Ethernet link up and speed is 10M
Yellow-flashing
Data transmission or receiving
Yellow-off
Ethernet is no link up Table 2-1 LED indications
10
2.4 Power
Input: - IEXT224-4PH-L (CO): Provide two redundancy local input powers; power voltage is 48VDC to 57VDC, terminal Block. - IEXT224-4PH-R (CPE): Provide two redundancy local input powers; power voltage is 48VDC to 57VDC, terminal Block. Output: - IEXT224-4PH-L (CO): Provide 96VDC output to VDSL Line (Remote Power Feeding) to support remote power to CPE. - IEXT224-4PH-R (CPE): Ethernet port provide 4-port POE PSE function to 802.3at (30W). Power Consumption: - IEXT224-4PH-L (CO): Max. 65W with Remote Power function enable, provide CPE POE PSE 30W. - IEXT224-4PH-R (CPE): Max. 45W with Remote Power function enable, provide CPE POE PSE 30W Protection: - Provide Over-Current protection and resettable smart Short-Circuit protection on both VDSL interface and POE PSE interface. Two power level output: - The function is set to detect CPE function. - When CO cannot detect CPE, output is 48VDC to VDSL line. - When CO detected that the CPE is successfully connected, POV output is 96VDC to VDSL line.
11
2.5 3-Position DIP Switch IEXT224-4PH-L & IEXT224-4PH-R are equipped with DIP Switch selection, which can allow users to select the parameters in order to meet the needs of different applications. The parameter options should be set identically on both CO and CPE sides. Option
Profile
SNR
Remote Power
On
Asymmetrical
6dB
Enable
Off
Symmetrical
9dB
Disable
12
3. Regulatory Compliance IEXT224-4PH-L & IEXT224-4PH-R are designed to comply with the following standards CE FCC Part 15 Class A EN60950
13
This page is intentionally left blank.
14
15
