Transcript
Codigo
Descripcion
02277‐60087 07575‐40013 07595‐60210 07595‐60237 07AA40136KC 07BA‐7010KC 07BB84518KC 07BB84525KC 0950‐2192OE 0950‐2435 0950‐3220 0950‐3354 0950‐3978OE 0950‐3988 0950‐4466 0950‐4476 0950‐4491 0957‐0256 1205‐0830 138327‐001 1420‐0552 149085‐001 149599‐001 1500‐0688 152728‐001 155592‐001 159535‐001R 161071‐001OE 161290‐001 163490‐001 163902‐001 163903‐001 164560‐001 171531‐001 172464‐001
Power supply board Left belt clamp ‐ Attaches carriage belt to carriage Motor/encoder assembly 'X' axis belt ‐ From media motor to grit wheel shaft pulley Lower feed roller ‐ Shaft with two rollers ‐ Next rollers (in paper path) after paper is pulled from the paper tray Control panel cover (L‐shaped) ‐ Shows button functions (English) DC power supply ‐ 220‐240VAC input, 50Hz Noise filter board ‐ For 220v to 240v, 50Hz operation POWER SUPPLY‐ EUROPE ROHS Power supply module (Autoranging) ‐ 100‐240VAC input, 50/60Hz, 0.35‐0.2A, 30‐50VA, requires separate AC power cord ‐ 10. Autoranging linear power supply ‐ 100‐240VAC input, 47‐63Hz ‐ Six DC outputs, 100 watts ‐ For worldwide operation Wall mount power supply module (MEI‐AH ED12010) ‐ 220‐250VAC input, 47‐53Hz ‐ 13VDC output, 800mA, 10.4 watts (South Afr Supply Power PFC MT Ultra slim AC adapter for OmniBooks ‐ Input voltage 100‐240VAC, 47‐63Hz, 100‐200VA, 1.5 amps ‐ Output voltage 19VDC, 3.3 Power module ‐ World wide (universal) ‐ 100‐240VAC input, 16VDC/32VDC output, and 40 watts ‐ Requires a separate AC powe Worldwide power module ‐ 100 to 240V Power module ‐ World wide (universal) ‐ 100‐240VAC input, 16VDC/32VDC output, and 40 watts ‐ Requires a separate AC powe Autoranging power supply (Delta SMP‐130DB) ‐ 115‐230VAC input, 47‐66Hz ‐ Five DC outputs, 130 watts ‐ For worldwide use Heat sink ‐ With spring clip ‐ For pin grid array type processor IC ‐ Black, 50.7mm x 50.4mm and 25.0mm high SPS‐BEZEL, DISPLAY 3.6V battery pack ‐ 950mAh, lithium, with cable and connector Pentium II, 266MHz, 512KB processor board ‐ Does not include processor KIT,SPS‐BATTERY PACK, NMH Carriage belt 40/80GB HP/Compaq DLT8000 External LVD 152728‐001 Intel Pentium III processor board assembly ‐ 600MHz (Katmai, 100MHz front side bus, 512KB Level‐2 cache, SECC‐2) ‐ Inclu Compaq Cooling Fan SPS‐POWER SUPPLY, 3 3V, 200W DUALA UX Fiber Channel (FC) adapter PC board ‐ 64‐bit, 66Mhz PCI bus master ‐ Has slots for two Gigabit Interface Converter (GBIC Rack mount conversion kit ‐ Includes front plate with handles and mounting hardware ‐ Install a tabletop StorageWorks MS 1GB 133MHz ECC SDRAM buffered DIMM memory module SCSI Backplane Board KIT,SPS‐BD,486 SYS W/O PRCSR Hot‐Plug System Fan 1.44MB 3.5in Floppy Disk Drive
Cantidad
1 3 1 1 1 1 1 1 1 1 7 1 1 1 3 2 2 1 1 1 1 2 1 3 1 2 1 1 1 1 1 1 1 1 1
172623‐001 179161‐001 187565‐001 189246‐001 197416‐001 201271‐001 217220‐001 221536‐001 224207‐001 228469‐001 228470‐001 228513‐001 231693‐001 238007‐001 240055‐001R 241016‐001 254971‐001 258611‐001 270183‐001 278017‐001 278747‐001 278791‐001 280279‐001 283606‐001 288456‐001 288472‐001 288689‐001 289564‐001 291641‐001‐H 292059‐B25R 292385‐001 294932‐005 300680‐B21 306431‐001 306569‐001
Backplane board (4 X 4) ‐ Has five ISA slots, two PCI slots, and three IDE connectors 1.44MB, 3.5in floppy disk drive (bezel‐less) ‐ Includes the 3.5‐inch to 5.25‐inch drive mounting tray adapter and mounti KIT,SPS‐CABLE K/M/V,SWBX‐CPU 10.4‐inch display bezel ‐ For CSTN display panels KIT,SPS‐POWER SUPPLY Miscellaneous plastics kit ‐ Includes two drive bay bezel fillers, front bezel trim (below front bezel), four rubber fee Power supply ‐ 300 watts Intel Pentium III processor ‐ 1.0GHz (Coppermine, 133MHz front side bus, 256KB Level‐2 cache, SECC‐2) ‐ Includes heat s Hot‐plug power supply assembly ‐ 350W 64MB DIMM EDO CPQ PROLIANT 128MB DIMM 60NS EDO PL3000 Hot‐plug fan assembly ‐ Includes a 60mm x 25mm (2.4in x 1.0in) 30CFM fan in a hot‐plug carrier Cable (Black) ‐ Narrow inverter cable for display panel Power supply (Delta DPS‐145PB‐40 B) ‐ 145 watt KEYBOARD N410C SPC‐ 64V RECEIVER Real‐Time Clock (RTC) battery ‐ Disk cell with connector 1.44MB Diskette Drive Memory expansion board ‐ Has four memory pairs for eight additional DIMM memory modules 256KB 12ns cache memory Motherboard (system board), 586 ‐ Does not include processor IDE CD‐ROM drive ‐ 16X‐max read ‐ Includes headphone jack and volume control 40/80GB DLT VS80 Low Voltage Differential/Single‐Ended (LVD/SE) SCSI internal tape drive (Carbon) 225W HOT PLUGGABLE powersupply 1.44MB 3.5in floppy disk drive without bezel 90‐Watt Power Supply Intel Pentium 4 processor ‐ 2.40GHz (Northwood, 533MHz front side bus, 512KB Level‐2 cache, FC‐PGA2, Socket 478) ‐ Inclu Processor power converter module ‐ 12V, 0.81A Compaq Left and right Hinges (14.1 and 15.1) ‐ 291641‐001‐H Bisagras MOBILE EXP. UNIT W/FD Mobile Unit Exp RSTRD 294932‐005N 2GB memory module kit ‐ Includes two advanced 1GB PC2100 DDR‐266MHz, ECC, 1.2‐inch registered DIMMs 128MB 100 MHZ SDRAM DIMM;1 X 128 MB Pass Thru Board
1 2 1 1 1 1 1 8 1 2 2 1 4 1 5 1 1 1 1 1 1 1 1 2 1 2 1 1 1 5 1 1 1 2 2
306572‐001 308615‐001 313299‐001 313611‐B21 314763‐B21 314941‐001R 323614‐005 327660‐001 329267‐001R 330956‐001 332829‐001R 332857‐001 333109‐001 333112‐001 333143‐001 333533‐161 33440‐69010 33449‐69005 33471‐69019 335698‐001 336218‐001 340855‐001 349046‐B21 355630‐161 361742‐001 365220‐001 367194‐001 378217‐001 378221‐001 378222‐001 378223‐001 378229‐001 378232‐001 378237‐001 378239‐001
Backplane Board with Cage Switching power supply ‐ 120‐240VAC input, 45‐66Hz ‐ Seven DC outputs, 240 watts, with Power Factor Correction (PFC) Hot‐plug 400W power supply ‐ 110/220VAC, 47‐63Hz input ‐ +12VDC, ‐12VDC, and +5VDC output Intel Pentium II processor option kit ‐ 350MHz Processor, KB Cache Memory, For PC Platforms FDD 1.44, 3.5"INT ARMADA7800 PS/2 two‐button scrolling mouse (Carbonite Black) ‐ Has 1.8m (72in) long cable with 6‐pin mini‐DIN connector Processor voltage regulator ‐ 120VAC, 5v 12v, 14amp, 40watt Processor voltage regulator ‐ 120VAC, 5v 12v, 19amp REM Keyboard Power Supply : Switching power supply ‐ 110‐240VAC input, 45‐66Hz ‐ 6 DC outputs, 145 watts Motherboard (system board), two DIMM slots, with processor retainer ‐ Does not include processor 3‐PCI Expansion Board with Brace Dual hot‐plug redundant power supply backplane board 64MB MEMORY MODULE PC100 /100MHZ/168 KBD/COMPAQ PS/2 STYLE DC POWER SUPASSY ‐ 240VAC, 50HZ LJ2/3 DC power supply assembly ‐ 120VAC, 60Hz Fusing assembly (240V, 50Hz) ‐ Bonds toner to paper by heat 256MB, 400MHz, CL=3.0, PC3200 non‐ECC DDR2‐SDRAM DIMM memory (Option DE466G) 1.44MB, 3.5in floppy disk drive without bezel or eject button (Carbon Black disk door) Smart Array 3200 Controller ‐ Dual channel 32‐bit PCI ‐ Wide Ultra SCSI‐3, Fast Wide SCSI‐2, and Fast SCSI‐2 ‐ Does not 24X CDROM (slimline)kit PS/2 'Windows' keyboard assembly (Silver and Carbonite) ‐ Has attached 1.8M (6.0ft) cable with 6‐pin (Violet) mini‐DIN c Battery pack ‐ Lithium‐ion (Li‐ION), 8‐cell, 14.8 volts, 4.4Ahr, rechargeable Power supply, 725‐watt, non‐hot‐plug, with tray Standard battery for iPAQ hx2000 series ‐ Lithium‐Ion, 920mAh Intel Celeron M 360 processor ‐ 1.40GHz (Dothan, 400MHz front side bus, 1MB Level‐2 cache) Intel Pentium M 740 processor ‐ 1.73GHz (Dothan, 533MHz processor side bus, 64KB level‐1 cache and 2MB internal level‐2 Intel Pentium M 750 processor ‐ 1.86GHz (Dothan, 533MHz processor side bus, 64KB level‐1 cache and 2MB internal level‐2 Intel Pentium M 760 processor ‐ 2.00GHz (Dothan, 533MHz processor side bus, 64KB level‐1 cache and 2MB internal level‐2 6‐in‐1 media reader interface ‐ Supports Secure Digital (SD), MultiMediaCard (MMC), Memory Stick, Memory Stick Pro, Smar LED switch cover ‐ Protective plastic cover installs above LEDs ‐ For use with Full‐Featured models Internal speaker Upper CPU cover (chassis top) ‐ Includes palm rest, touchpad with ribbon cable, and EMI shields
2 2 2 1 1 1 1 1 2 1 1 3 2 1 4 1 1 1 2 2 1 2 1 2 1 1 1 1 2 1 1 1 1 3 1
378239‐001R 378240‐001 378242‐001 382407‐001R 388058‐001 388191‐002R 390394‐001 390937‐001 394277‐031R 394283‐001R 394285‐001R 394462‐002R 394903‐001 396632‐001 398832‐001R 400546‐001 403708‐001 412239‐001 430467‐001 432874‐001 5063‐0309 5063‐0349 5063‐1254 5063‐5705 5063‐7922 5063‐7943 5063‐8782 5063‐8794 5064‐0230 5064‐0246 5064‐1954 5064‐6603R 5064‐7482 5090‐3389 5181‐8774
cover inferior CPU base enclosure (chassis bottom) ‐ Does not include the speaker assembly LED switch cover ‐ Protective plastic cover installs above LEDs Keyboard cover for de‐featured (DF) products ‐ With wireless and infrared (Presario) Redundant Fan with Bracket Compaq 64MB Memory Module ( PC100/ 100MHz/ 144 Pins ) Power Supply : Hot‐plug power supply ‐ 725W, 12V HP PS/2 (Carbonite) scroll mouse Keyboard assembly ‐ 88 keys (101‐key compatible) with Windows key ‐ Integrated 10‐key numeric keypad (United Kingdom) Upper CPU cover (chassis top) ‐ Includes palm rest, touchpad with ribbon cable, left and right speakers assembly ‐ De‐fe Chassis bottom (lower case) assembly Mini PCI 802.11b/g Titus wireless LAN (WLAN) card ‐ Supports IEEE 802.11b/g wireless standards (ROW) AC adapter ‐ Input voltage 100‐240VAC, 7.1A, 50/60Hz ‐ Output voltage 135‐watt, 19VDC, with power factor correction (PFC SPS‐ADPTR,INTFC,CYBD/VID/MSE Battery pack ‐ 4.4Ahr, 6‐cell lithium‐ion (Li‐Ion) ‐ Rechargeable Smart Array 221 Controller with 6MB cache ‐ PCI to Wide Ultra2, single‐channel array controller DVD‐ROM/ CD‐RW combination drive (Multibay) PC Board : Motherboard with Centrino technology ‐ Includes the Intel 945GML Top cover assembly ‐ For models with a web camera and microphone Fan/Heat Sink : Heat sink with fan GUIAS PARA FDD 3.5" RSTRD 0950‐2421 IEEE 1284 Bi‐Tronics parallel cable ‐ DB‐25 (M) connector (type A) to 36‐pin high density IEEE 1284C (M) connector (type Status panel assembly ‐ Includes power switch and activity LEDs Side mounting drive rail kit ‐ Includes one set of rails for 3.5‐inch, and one for 5.25‐inch wide drives Autoranging power supply ‐ 100‐240VAC input ‐ For worldwide use Backplane board ‐ Has connectors for video, LAN, and accessory PC boards Voltage regulator module ‐ For Pentium Pro processors ORDER 5064‐1838 Intel Pentium processor ‐ 200MHz (P54C) ‐ Does NOT include heat sink System fan POWER SUPPLY MODULE 300 WATTS Front bezel (plastic) ‐ Attaches onto the front of the metal chassis assembly ‐ Includes on/off switch BUNDLE: LJ POCKET GDE Elevator motor
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 1 3 1 2 1 1 1 1 1 1 2 1 2 1
5181‐8775 5182‐1857 5182‐4550 5182‐4572 8120‐4997 8120‐6312 8120‐8473 8121‐0019 9100‐5165 A4800‐69002 A5191‐04003 A5191‐63001 A5191‐67104 A5191‐69210 A5527‐69001 C1633‐20034 C1633‐40006 C1633‐40019 C1633‐40027 C1633‐40028 C1633‐40030 C1633‐40038 C1633‐40051 C1633‐40064 C1633‐40082 C1633‐80004 C1633‐80006 C1645‐69111 C1676‐20014 C1676‐60092 C2001‐69009 C2002‐67901 C2024‐60100 C2041‐69001 C2080‐69001
Feed roller motor Audio cable assembly ‐ For CD‐ROM, CD‐RW, or DVD‐ROM ‐ 4‐pin (F) connector to 4‐pin (F) connector ‐ 47.8cm (18.8in) long SCSI adapter (68‐pin (F) to 50‐pin (M)) ‐ Used in some configurations for the CD‐ROM drive and/or another Single‐Ended S Fast Wide SCSI ribbon cable marked 'PCI board to MS cage C15‐90 ohm' ‐ Two 68‐pin (M) connectors marked 'To PCI board' a Inline Single‐Ended SCSI passive terminator ‐ 50‐pin low density (M) connector with bail locks to 50‐pin low density (F) Power cord (Black) ‐ 2‐wire, 18 AWG, 1.8m (6.0ft) long ‐ Has straight (F) C7 receptacle (for 240V in Australia, Argentin IEEE 1284 Bi‐Tronics parallel cable (Flint Gray) ‐ DB‐25‐pin (M) connector (type A) to DB‐25‐pin (F) connector (type A) Power cord (Flint Gray) ‐ 18 AWG, 2‐conductor, 1.8m (6.0ft) long ‐ Has straight (F) C7 receptacle (For 220VAC in Argenti FUENTE JETDIRECT Single port Ultra Wide Differential SCSI‐2 PCI card ‐ Has one external 68‐pin high density connector and one internal 68 172mm I/O card cage 'hot swap' fan Console cable ‐ Has one DB‐25 (M) connector and three 20.3cm (8in) cables with DB‐9 (M) connectors Disk/media backplane ‐ Has power and SCSI connectors for removable media mass storage devices on one side and four SCA c Platform monitor PC board Hot‐swap redundant power supply ‐ 100/240VAC input, 50/60Hz, autoswitching Bushing for reduction pulley Wiper pad Overdrive gear cluster Bail engaging lever gear Bail lift cam gear Pinchwheel manual lift handle ‐ Paper loading lever Left bail bracket FLAG, SENSOR Media sensor mounting bracket Pincharm spring retaining bushing Extension spring ‐ Holds the rollfeed access cover closed Bail engaging lever spring Power supply board Encoder strip (clear strip with position marks) ‐ Used by the sensor in the carriage assembly to determine position Carriage assembly trailing cable HIGH VOLTAGE POWER SUPPLY 4‐4M (P OBSO.) Formatter (Main logic) board 1MB memory module ‐ For LaserJet FORMATTER LJT 4MP Postscript SIMM module ‐ Includes 35 adobe fonts
1 1 1 1 1 1 2 2 4 3 4 1 1 1 2 2 1 1 3 2 1 1 1 5 2 1 2 1 1 2 1 1 1 1 1
C2124‐80008 C2145‐67851R C2164‐60008 C2169‐60056 C2570‐69010 C2670‐60109 C2670‐60131 C2678‐60107 C2684‐60204 C2684‐60242 C2684‐60302 C2693‐67003 C2693‐67008 C2693‐67040 C2801‐40001 C2847‐20017 C2847‐40013 C2847‐60021 C2858‐40003 C2858‐60005 C2858‐60021 C2858‐60024R C2858‐60208 C2859‐60208 C3113A C3133AOE C3170‐60009 C3180‐60001 C3190‐40019 C3190‐40020 C3190‐40034 C3190‐40076 C3190‐60004 C3190‐60130 C3190‐60144
Encoder strip ‐ Clear strip with position marks ‐ Used by the sensor in the carriage assembly to determine position CARRO DKJ 820 SIN PCA Sensor PC board ‐ Contains optical media sensors and mechanical switch for access door Service station assembly with motor and sled ‐ Does not include service station motor cable RSTRD C2570‐60010/C2570A Stopper guides ‐ Mounts on the bottom of the printer and guides the paper input tray stopper Carriage drive motor ‐ Includes pulley Line feed motor Power supply PC board Kicker assembly ‐ Attached to pick roller shaft Pick roller assembly ‐ Has 1 large roller and 2 small rollers Rear cleanout door assembly ‐ Paper jam cleanout door Top/front access door assembly ‐ Print cartridge access door ‐ Includes the access door and the main back panel Service station motor Height sensor arm Screw‐Shoulder Bail engaging lever ‐ Used to move engaging lever gear Media sensor assembly ‐ Includes cable COVER, SVCE STATION SENSOR, BAIL Cutter mechanism assembly ‐ Auto cutter for rollfeed paper TRAILING CABLE DJT 650C INACTIVA ENCODER STRIP (A1) METAL CAMBIA POR C4714‐60098 HP Color LaserJet Letter paper input tray 8MB, 70nS, 36‐bit SIMM memory module ‐ For HP LaserJet 4P, 4+, 4V, 5, 5N, 5M, 5P, 5Si (REFURBISHED) Reduction pulley ‐ Includes 2 Bearings, Shaft (0.16in Diameter on Both Ends), Flange, Pulley and Instructions Media sensor assembly Bail lift cam gear Bail lift cam ‐ Mounted behind the bail engaging lever support ORDER C4699‐60037 Cartridge cap ‐ Keeps cartridges from drying out when carriage is parked in service station Spittoon assembly ‐ Contains absorbers which hold excess ink from cartridges Sensor mechanism ‐ Does NOT include the media sensor assembly Control panel assembly ‐ Mounts in right side cover ‐ Includes control panel, panel support, and cover sensor
7 1 2 21 1 3 1 1 1 1 1 1 1 1 1 2 2 1 3 2 2 1 6 2 1 1 16 1 2 1 1 1 2 1 1
C3195+49A‐600 C3195‐40007 C3195‐40039 C3195‐60027R C3195‐60056 C3540‐60250 C3751‐60201 C3760‐60502 C3764‐60502 C3768A C3774A C3801‐80004 C3909A C3919‐69001R C3990‐90991 C4085‐67902 C4092A C4110‐69001 C4124A C4125‐67901R C4146‐60001 C4146‐60001R C4169‐69001 C4209‐69001 C4214‐69009OE C4218‐90901 C4345‐60040 C4358‐60041 C4358‐60042 C4392‐60019 C4459‐69001 C4504‐61230R C4531‐40020 C4602‐60022 C4602‐67901
DJ750/55DIS NTSC TRGKT END COVER (LEFT) Pulley wedge tensioner ‐ For carriage (Y‐axis) belt tension SPITTOON ASSY Power supply cable ‐ Has 12‐pin (F) connectors ‐ 9.5cm (3.7in) long Carriage assembly trailing cable ‐ Has two ribbon cables bundled together ‐ 85.7cm (33.8in) long PS/2 two‐button serial mouse (Quartz Gray) ‐ Has attached 6ft cable with 6‐pin mini‐DIN connector 500 sheet universal paper tray ‐ For optional lower cassette HEAD ASSEMBLY PAPER HANDLING CONTROLLER BOARD MULTIBOX PARA LASERJET 5SI/8000 Encoder strip ‐ Used to determine carriage position Black (Micro‐Fine) toner cartridge ‐ Page yield index 15,000 FORMATTER ASSY‐LJT 5 MANUAL SVCE‐ LJ5L/6L Self paced training kit for LaserJet 5Si Series and 8000 Series ‐ Includes PAL format video (VHS), and student guide Ultra‐Precise Black toner (EP) cartridge DC controller board with ribbon cable HP LaserJet 4000/N/T/TN 500 Sheet feeder with universal paper tray ‐ Holds up to 500 sheets of paper from A5 size to leg 500 sheet universal paper tray assembly REF Formatter PC board FORMATTER LJT 1100 Formatter board assembly Formatter (Main logic) board ‐ For duplex capable printers DC CONTROLLER 8150 OEM LASERJET 1100A QUICK REFERENCE GUIDE CABLE CD WRITER 6020 EXT CABLE PARALELO DEL CDWRITER 7100 EXT FUENTE DEL CDWRITER 7100/7200 EXT. SRV‐SFTW MNL 8100I CD‐Writer Plus 9100i/9110i IDE drive ‐ 8X CD‐R write, 4X CD‐RW write, 32X CD‐ROM read FUENTE CD WRITER 8230E REM Tray cover ‐ Snaps on top of input/output paper tray assembly Carriage motor ‐ Provides power for carriage belt Service station kit ‐ Includes housing, absorber, pre‐filter, cartridge blotter pads, tumbler assembly, tools, and instr
3 1 1 1 2 1 1 1 1 5 2 1 1 2 1 1 1 1 1 2 1 1 1 1 1 3 1 3 1 1 1 1 1 1 1
C4608‐60029 C4608‐60029R C4699‐60002 C4699‐60003 C4699‐60037 C4699‐60085 C4704‐60024 C4704‐60082 C4705‐60056 C4705‐60082OE C4705‐60113 C4713‐40016 C4713‐40046 C4713‐60098 C4713‐60119 C4713‐60182 C4714‐60093 C4723‐60276 C4735‐60304 C4780‐69503 C4788‐60519 C4793‐67901 C5160‐60100 C5629A C5870‐00004 C5870‐40017 C6072‐60178 C6072‐69146 C6074‐60419 C6409‐40031R C6409‐60003 C6680‐80003OE C6680‐80050 C7044‐69001 C7052‐90923
Paper output tray ‐ Black BANDEJA DKJ 692 BLACK Spittoon assembly ‐ Includes pincharm sensor switch and absorbers which hold excess ink from cartridges Primer assembly ‐ Mounted on left side of plotter RIGHT CAM JOURNAL ASSY Clutch Assy (Serv) Ribbon cable assembly ‐ Has 28‐pin (F) connectors ‐ 23.5cm (9.3in) long Housing assembly (on left side) X‐AXIS MOTOR ASSY BELT CARRO DJT 250,330,350,450,750 (A1) SEE C4705‐69113 Bail engaging lever support ‐ Mounted over the left end of the drive roller ‐ Bail engaging lever snaps into this item Power switch button/keycap Encoder strip assembly (D‐size) ‐ Includes encoder strip and encoder strip spring Self‐paced training kit for DesignJet 430/450C/455CA/488CA ‐ Includes video in NTSC format, and CD‐ROM containing user's Flexible stranded wire cable ‐ 12.5cm (4.9in) long Bail assembly (E‐size) ‐ Has star wheel assemblies attached Service station assembly KYBRD WINDOWS Paper feed assembly ‐ Vertical transfer unit ‐ Transfers paper from pickup assembly up to the printer input Stapler assembly ‐ Staples jobs sent to carriage assembly 250‐sheet tray feeder assembly ‐ Includes the feeder base assembly and 250‐sheet paper cassette ‐ Can hold letter, legal Paper input tray ‐ ADF with legal size pull‐out extension Photocopier drum kit ‐ Includes drum, transfer assembly and package of wipes ‐ Assembly with fold out handle on top Wear strip ‐ Long, spring loaded strip mounted in top of backbone ‐ Used to ensure smooth ink cartridge carriage motion Cluster gear (large gear) Service station assembly ‐ Includes drop detector assembly Electronics module ‐ Contains power supply, main logic board and cooling fan CARRIAGEMOTOR ‐ INCLUDES PULLEY CARRO SIN PCA DJ 840 Ink cartridge carriage assembly ‐ This item should be replaced only by trained, experienced service personnel CABLE PARALELO LJT 1100/ SERIES R OEM Scanner module trailing cable ‐ Has 20‐pin (M) edge connectors ‐ 42.9cm (16.9in) long Laser/scanner assembly CAMBIA POR C7052‐90930
6 1 2 1 3 1 1 1 1 1 1 3 1 2 1 2 2 1 3 1 1 1 2 1 1 2 1 1 1 2 1 1 1 1 1
C7160‐16503 Power supply module (HiTRON HES10‐12010‐0‐7) ‐ 100‐240VAC input, 50‐60Hz, 0.33‐0.19A, requires separate AC power cord ‐ C7160‐16600R CABLE PARALELO SCANJET 3200 C7281‐68001 Main logic PC board C7769‐60373 Ink Supply Station (ISS) ‐ Includes ink pump motor, pump sensor, and out‐of‐ink sensors C7791‐60230 Upper paper guide roller kit (includes 8 rollers) C7791‐60245 Starwheel assembly ‐ Provides downward pressure on media as it passes through the feed rollers C7796‐60016 Main logic PC board module C7796‐60205 Carriage assembly ‐ Includes trialing cable C7833‐60102 Power supply module ‐ 100‐240VAC input, 50‐60Hz ‐ 24VDC output, 2.7A, 65 watts ‐ Includes detachable AC power cord for u C8116‐67052 Paper feeder ‐ Includes encoder C8136‐67013 Rail cover ‐ Mounts over the starwheel assembly C8222A Battery pack ‐ Lithium‐ion (Li‐Ion) C8519‐90912 MANUAL LJT 9000 C8554A Image Cleaning Kit ‐ Includes one air filter, one transfer cleaner (cleaning blade), one toner collection bottle C9651‐67901 Formatter board assembly C9652‐69001 Formatter board assembly CSC‐AIR‐ANT4941ANTENNA 2.2DBI DIPOLE D2198B Hard drive mounting tray kit (package of 3) D2342‐69001 System processor board ‐ Includes integrated IDE and Fast SCSI‐2 controllers and (Standard) VGA video D2887‐63001 Integrated office board ‐ Fax/modem/audio board D2971‐63006 ECC memory expansion board ‐ Has 12 additional SIMM sockets D3025‐69002 System processor board ‐ With Ultra VGA & IDE controller built‐in D3151‐69001 System processor board ‐ With Ultra VGA & IDE controller built‐in D3310‐69006 System (Mother) board ‐ Includes IDE hard drive and floppy controllers, Super VGA video, and internal/external SCSI‐2 po D3390‐69006 System processor board ‐ Includes integrated IDE controller and Ultra VGA video D3566A Side mounting rails (five pair) ‐ For mounting 3.5‐inch wide, 1/3 height multimedia drives ‐ Includes machine screws and D3581‐69001 1.05GB hot‐swap Fast SCSI‐2 hard drive module (Parchment White) D3653‐69001 System processor board ‐ Includes integrated IDE controller and Ultra VGA D3659B 256kB synchronous pipeline burst cache memory D3961‐69001 System processor board ‐ Includes integrated enhanced IDE controller and S3 Trio 64 Ultra VGA video D4205‐69002 System processor board ‐ Includes integrated IDE controller (Does NOT have a video controller) D5182‐63001 PLACA DE SONIDO D6970‐63002 Fan assembly ‐ Includes two tubeaxial fans mounted on a bracket D7140‐90008 E 60 Training Self‐Paced D8155‐63015 SEE D8155‐69015
1 1 1 1 2 1 1 1 1 1 1 5 1 2 1 2 1 4 1 1 1 2 1 2 1 6 1 1 2 1 1 6 3 1 4
D8228‐69001 I/O board ‐ Contains four 64‐BIT PCI, two 64‐BIT and two 32‐BIT 'hot plug' PCI accessory card slots ‐ Includes extractor D9351‐63004R NETRAID, 4M, 128MB REL 4 D9387‐63015 Power supply ‐ Autoranging 110/220VAC input, 50‐60Hz, 256 watts ‐ Has fan speed control ‐ For worldwide use F1137A Battery pack ‐ Lithium‐ion (Li‐Ion) ‐ Rechargeable F2026‐12006 CD‐RW burning software F2188‐60902 Display hinge ‐ Mounts to display case and bottom case assembly ‐ For 14.1‐inch displays (IBM) F4356‐60005 Stylus pen for Jornada 728 palmtop FILM4100OE FILM FUSOR LJ 4100 H3976‐60002OE KIT DE MANT. LJ 1000/1200/3300 220V H3977‐60001TM Paper path roller kit ‐ Includes pickup D rollers (8 each) , Feed/Sep rollers (4 each) and Tray 1 pickup (8100) H3977‐60002 CNTRL PNL KEYPAD RPL KIT HS150PX14 LCD CABLE for HP compaq nx9005 (J545) J2552‐69013OE JET DIRECT COMBO PARA LASER 5 AND OTHER J2591‐69001 External JetDirect LAN interface module with EtherTwist (10Base‐T) and ThinLAN (10Base‐2) connectors J2603‐69001 ADVANCESTACK ETHERTWIST (10BASE‐T SNMP M J2603B AdvanceStack Ethertwist (10Base‐T) SNMP module ‐ Provides 'In‐band' network management for up to 16 hubs J2607A Ethertwist transceiver module ‐ Has one RJ‐45 connector (10Base‐T port) J3133A AdvanceStack SNMP module assembly ‐ Includes the SNMP module (with 9‐pin console port), CD‐ROM kit, and a manual J3191A AdvanceStack expansion module assembly ‐ Has two empty bays for optional 100Base‐T tansceivers J3200‐69101 AdvanceStack hub assembly ‐ Includes 12 (F) RJ‐45 connectors (10Base‐T ports), transceiver module slot, management modul J6072‐61001OE HP bt1300 Bluetooth wireless printer adapter ‐ Allows for wireless printing from Bluetooth enabled PCs, PDAs, phones L1624A Lamp module ‐ For Digital Projectors vp6110 and vp6120 P4648‐63018 CD‐ROM drive or 5.25in drive quick remove tray Q1278‐60018 WHITE BACKGROUND ASSY 40/42 INCHES Q1321‐67925 Electromagnetic clutch ‐ K‐drive development clutch ‐ Clutch CL2 Q2465‐67901 FORMATTER REPLACEMEN PCA LJ1012 USB M1‐B Q2613A Ultra‐precise black toner cartridge (economy) ‐ Will print approximately 2,500 pages based on a 5% print density Q2658‐67901 Printer formatter board ‐ Controls the logic and timing operation of the printer, translates the control panel input, an Q3701‐60010OE PC Board (Modem) : Modem PCA ‐ HP LaserJet analog fax accesory 300 Q3709A Optional 250 sheet paper input tray ‐ Includes tray base which attaches to printer, and the slide out paper tray ‐ Accom Q3955‐61003 Formatter (main logic) board ‐ Network version R98‐1006‐000CN Tray 5 assembly ‐ Complete tray with identification label R98‐1007‐000CN Tray 4 assembly ‐ Complete tray with identification label RA0‐1026‐000CN Torsion spring ‐ Provides grounding connection to the toner cartridge (photo sensitive drum) RA0‐1177‐000CN Front cover ‐ Lower front of printer ‐ With opening for inserting the paper input tray assembly
1 1 1 1 1 1 1 8 2 4 10 1 4 1 1 1 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
RA1‐4038‐000CN Fusing assembly cover (Black, plastic) ‐ Covers fusing assembly when lid is closed RA1‐7627‐000CN Transfer charge roller (Black) ‐ In paper path door assembly RA1‐7630‐000CN 'Face‐Up' paper output tray ‐ Hooks on front of printer RB1‐0557‐040CN Paper guide ‐ Attaches to the delivery cover on the printer ‐ Aids in preventing paper jams RB1‐1294‐000CN Left slide arm ‐ Supports front door when printer is opened RB1‐1318‐000CN PLATE, PRESSURE, LEFT RB1‐2101‐000CN RT CART SIDE PLATE RB1‐2105‐030CN Toner cartridge support ‐ Black plastic bar that attaches above the toner cartridge RB1‐2127‐000CN Pickup roller (Oval shaped) ‐ For multipurpose tray RB1‐2133‐000CN Paper out sensor arm RB1‐2299‐030CN Delivery roller ‐ Double roller in paper output assembly RB1‐2322‐000CN Door ‐ On top of printer ‐ Lift‐up printer access cover RB1‐2351‐000CN MP door ‐ On front panel ‐ Does NOT include tray extension RB1‐2354‐000CN Support strap for rear door ‐ Supports door when open RB1‐2978‐000CN Power cord door ‐ On right side ‐ Access for power cord RB1‐3029‐000OE PICK UP ROLLER LJ 4L OEM RB1‐3100‐000CN Lower pressure roller ‐ Hard rubber roller ‐ Located in fusing assembly RB1‐3103‐000CN Exit roller ‐ Shaft with 3 rubber rollers ‐ Located in fusing assembly RB1‐3109‐000CN Conductive roller ‐ 'Tire' like roller that mounts on end of pressure roller shaft (Next to drive gear) RB1‐3138‐000CN Torsion spring for back door assembly RB1‐5934‐000CN Interface connector cover ‐ Attaches to the left side cover RB1‐5939‐000CN Sensor arm ‐ Detects if paper is in multipurpose input tray RB1‐6130‐000CN Tray 1 pickup roller gear RB1‐6444‐000CN Release arm RB1‐6458‐000CN Shutter RB1‐6480‐000CN Lower Left Cover ‐ Mounted below diverter door assembly RB1‐6495‐000CN FRONT COVER (REMOVAL) RB1‐6557‐000CN Paper input unit sensor arm ‐ Senses when paper passes through paper input unit RB1‐6558‐020CN Sensor arm torsion spring ‐ Holds tension on PIU paper sensor arm RB1‐6614‐000CN FLAG FUSER RB1‐6667‐000CN Diverter door assembly ‐ Upper door on left side of printer ‐ Two struts are mounted to door RB1‐6693‐000CN PAPER HEIGHT LEVER RB1‐6730‐000OE PICKUP ROLLER LJT 5SI 8000 TRAY 1 RB1‐7129‐000CN Case grounding strap (metal) RB1‐7185‐000CN Left leg ‐ Small leg on left side of paper kick plate
1 2 1 1 1 1 1 1 3 4 8 3 2 1 1 1 1 3 4 4 1 1 1 1 2 1 1 1 2 5 1 1 3 4 1
RB1‐7186‐000CN Right leg ‐ Small leg on right side of paper kick plate RB1‐7197‐020CN Clutch RB1‐7246‐000CN Pressure roller bushing RB1‐7288‐020CN Exit roller bushing RB1‐7294‐000CN Spring ‐ For paper exit sensor arm RB1‐7321‐000CN Memory expansion cover (Door) ‐ Located on the left side of the printer RB1‐7326‐000CN Large paper output extender ‐ Does NOT include smaller extender RB1‐7327‐000CN EP DOOR CHIMNY RB1‐7334‐000CN Jam prevention protector ‐ Installs in the delivery assembly ‐ Allows paper jams to be cleared without damaging the prin RB1‐7813‐000CN Paper registration sensor flag RB1‐7885‐000R Tray : Multi‐Purpose tray extension RB1‐7886‐000R Door : MP door ‐ On front panel ‐ Does NOT include tray extension RB1‐7901‐000OE MOUNT, DOOR‐ TRAY 1 RB1‐7983‐BULK Pickup Roller ‐ MIN/MULT= 140 PALLET= 8400 RB1‐8674‐000OE SHAFT, BELT DRIVE LJ4000 OE RB1‐8715‐000CN DISK BELT RB1‐8756‐000OE TONER CARTRIDGE DRIVE OEM RB1‐8827‐000CN Leaf spring RB1‐8877‐000CN Coupler Pickup RB1‐8974‐000OE SEPARATION ROLLER CLUTCH LJ4000 OE RB1‐9181‐000CN NO USAR****PEDIR COMO RB1‐9181‐020 RB1‐9351‐000CN Paper support arm RB1‐9354‐000CN Paper guide ‐ For LaserJet companion RB2‐0445‐020CN LEVER, FLAPPER RB2‐0545‐000CN Paper pickup shaft ‐ Shaft that pickup rollers attach to RB2‐0717‐000CN Smaller pickup roller for tray 1 ‐ Snaps onto shaft RB2‐0744‐000CN Larger pickup roller for tray 1 ‐ Snaps onto shaft RB2‐1745‐000CN Front cover pin ‐ Hinge pins for drop down front cover RB2‐1887‐000OE Large feed belt ‐ Wide belt in middle of assembly RB2‐1888‐000CN Small paper feed belt ‐ One on each side of wide belt RB2‐2825‐000CN Belt shaft 3 RB2‐2862‐000CN Right rear side cover ‐ Swing away I/O cover ‐ Has slots on back for I/O cable plug‐in access RB2‐2892‐000CN Guide roller (Free spinning white plastic roller) ‐ Mounts on the paper pickup drive shaft on each side of the pickup 'D RB2‐2898‐000CN FEED ROLLER LJT 2100 RB2‐2935‐000CN Gear coupler
3 1 2 9 1 3 3 1 4 2 1 1 9 1 1 3 20 2 5 10 1 1 1 2 2 3 3 1 1 2 10 1 1 1 3
RB2‐3005‐000OE Arm : Release arm ‐ Right side lifting plate release arm RB2‐3007‐000CN Separation pad ‐ Small rectangular rubber pad on front of metal lifting plate RB2‐3037‐000CN Tray 1 extender ‐ Flip‐out paper extender RB2‐3044‐000CN Right roller bushing ‐ Acts as the bearing and retainer for the right end of the paper pickup roller assembly (tray 1) RB2‐3054‐000CN Idler shaft RB2‐3056‐000CN Belt drive shaft 2 ‐ Front of middle wide belt ‐ Tiny drive belts attach on each end of this shaft RB2‐3058‐000CN Paper feed belt ‐ Wide middle belt RB2‐3060‐000CN Paper feed belt ‐ Short/tiny belts in front of and on each side of middle belt of paper transfer assembly RB2‐3082‐000CN Feed roller bushing ‐ Left side feed roller support RB2‐3484‐000CN Feed roller ‐ Feed roller for sheet feeder ‐ White plastic roller RB2‐3490‐000CN Feed roller ‐ Tray 3 feed roller RB2‐3522‐000CN PRESSURE ROLLER LJ8100 RB2‐3558‐000OE DELIVERTER DOOR ASSEMBLY RB2‐3631‐000CN Paper feed clutch cover RB2‐3930‐000OE SOPORTE PICK UP LJT 1100 3200 OE RB2‐3931‐000CN Idler roller ‐ Supports pickup roller shaft in holder RB2‐3947‐000CN Separation pad holder retainer ‐ White plastic clip RB2‐3960‐000CN Paper output sensor flag RB2‐4006‐000CN Paper output deflector RB2‐4034‐000CN Printer door rail arm mount RB2‐6348‐000OE SEPARATION PAD LJT 2100 OE RB2‐8769‐000CN ADF pickup roller RC1‐0060‐030CN Paper feed sensor flag for Tray 1 RC1‐0070‐000CN Pressure roller ‐ Roller in fusing assembly that provides pressure for media against the fusing roller RC1‐0288‐000CN Formatter board cover RC1‐0954‐000OE Separation Pad RC1‐0978‐000CN Delivery roller ‐ Roller for Upper Delivery Guide ‐ 4 Used RC1‐1535‐000CN Pickup roller ‐ Tray 1/MP Tray pickup roller RC1‐3472‐000CN Paper sensor flag ‐ cylindrical plastic piece with a flag on each end (One senses the paper, the other activates the pho RC1‐3937‐000OE Pad holder ‐ Separation pad holder RF1‐1145‐020CN Separation pad ‐ Rectangular pad mounted on registration assembly RF1‐2073‐000CN Paper pickup guide ‐ Has curved clear piece & teflon tape RF1‐2394‐000CN Input feed roller/shaft (Only) ‐ Has drive gear between the two feed rollers RF5‐0343‐000OE Separation pad RF5‐0343‐BULK MP SEPARATION PAD ‐ MIN/MULT= 200 PALLET= 12000
1 1 8 1 5 2 1 1 1 2 2 1 2 2 2 1 2 7 1 1 9 2 4 1 2 8 1 1 1 5 1 1 4 17 1
RF5‐0349‐000OE TRANSFER ROLLER LJT 5 OEM RF5‐0369‐000CN PEDIR COMO RF5‐0369‐040 RF5‐0400‐000CN Delivery sensor arm RF5‐0425‐040CN Output roller & holder RF5‐1077‐030CN Lower delivery roller ‐ Shaft with 4 double rollers on it RF5‐1290‐000CN Transfer charge roller ‐ Behind transfer guide assembly RF5‐1394‐000CN Transfer guide ‐ Guide transfer roller is mounted into RF5‐1455‐000OE SEPARATION PAD LJ 5SI/8000 OEM RF5‐1516‐000OE PRESSUROLLER LJT 5L/6L OEM RF5‐1517‐000CN Fuser pressure plate ‐ Guides paper over fuser roller RF5‐1530‐000CN Transfer roller guide ‐ Fits over top of transfer roller RF5‐1534‐000OE TRANSFER ROLLER LJ 5L/6L OEM RF5‐1834‐000OE FEED SEP ROLLER LJ 5SI/8000 TRAY 2/3 RF5‐2603‐000CN Delivery roller ‐ Feeds paper out of fusing assembly RF5‐2604‐000OE Roller : Delivery roller ‐ Upper face‐down delivery roller RF5‐2694‐000CN FUSING SENSOR ARM LJT 5SI RF5‐2701‐060OE Support RF5‐2703‐000OE PAD SEPARATION‐ TRAY1 OEM RF5‐2708‐000CN Pickup roller ‐ Used in paper pickup assembly ‐ 2 used RF5‐2760‐000CN Paper stop for 500 sheet tray RF5‐2822‐000OE Roller : Output roller ‐ Face‐up output roller RF5‐2830‐000CN Output roller ‐ Face‐down output roller RF5‐2886‐000OE SEPARATION PAD ARM LJ1100 OEM RF5‐3319‐000CN Transfer roller ‐ Includes the long black spongy roller, roller shaft, and drive gear ‐ (LJ9000) RF5‐3403‐000CN Pickup roller for optional Tray 1 RF5‐3808‐020CN ADF separation pad assembly RG0‐0110‐140CN Delivery assembly ‐ Feeds paper to top face down output tray RG0‐1019‐000CN Roller and holder assembly ‐ Spring loaded roller in a black plastic holder assembly ‐ Mounts on top of the paper pickup RG0‐1020‐000OE PICK UP GEAR ASSEMBLY LJT 1200 RG0‐1024‐000CN Control panel assembly ‐ Includes the control button and indicator LED's mounted on the left front cover support RG0‐1030‐000CN Fan and airflow guide assembly RG1‐0908‐000CN Dual cable assembly with ferrites ‐ One 7‐pin (F) connector, two 5‐pin (F) connectors, and one 4‐pin (F) connector ‐ 43. RG1‐0933‐060CN Transfer Corona assembly ‐ Square tube with wire wrapped around it RG1‐0935‐000CN Upper pressure assembly ‐ 'T' bar RG1‐0936‐110CN High voltage power supply assembly
1 1 1 3 11 11 7 2 3 1 2 1 3 1 6 2 1 1 6 9 1 7 17 6 3 4 1 1 15 1 1 1 3 1 1
RG1‐0966‐030CN Fusing roller cleaning pad ‐ Felt 'Wand' in fusing assembly RG1‐1912‐080CN Separation pad ‐ Rectangular pad ‐ Behind pickup roller RG1‐4276‐030CN CONTROL PANEL ASSY RG5‐0039‐070CN Right block ‐ Side of main structure before fusing assembly RG5‐0231‐000CN Front cover connect board ‐ Located behind left side of front door ‐ Has delivery unit paper sensor (PS401) and door ope RG5‐0449‐000OE LASER SCANNER LJ 4 OEM RG5‐0456‐180CN Paper output assembly ‐ Belt driven RG5‐0468‐000CN Transfer guide assembly ‐ Ribbed paper guide for the high voltage transfer roller (Does NOT include transfer roller) RG5‐0511‐000CN DC controller board RG5‐0512‐070CN Paper control board ‐ On right side of paper feed assembly RG5‐0514‐000CN Sensor board ‐ Narrow board w/ sensors RG5‐0553‐000OE POWER SUPPLY 220V LJ 4/4M RG5‐0679‐000CN Fusing roller assembly ‐ Includes heating element and teflon sleeve ‐ For 220V/240V LJ 4L/4ML/4MP Canon LBP‐430/4i RG5‐0682‐030CN Lower roller assembly (L‐shaped) ‐ For top cover output RG5‐0683‐020CN Upper roller ‐ Shaft with 4 rollers ‐ For top cover output RG5‐0765‐000OE MAIN MOTOR LJ 4L/4P/4MP discontinuado RG5‐0802‐000CN Mirror assembly ‐ Top, center of internal chassis RG5‐0805‐000CN Power switch assembly ‐ AC input, power switch, and power switch holder ‐ Also includes interconnecting cables RG5‐0886‐070CN Paper output assembly ‐ Belt driven RG5‐0888‐000CN Multi‐Purpose input tray ‐ Attaches to front door RG5‐0978‐000CN Cable assembly ‐ From DC controller to main motor RG5‐1442‐000CN Cable assembly ‐ 4‐pin (F) connector to 3‐pin (F) connector ‐ 31.1cm (12.3in) long RG5‐1565‐000CN ASSY,PAPER GUIDE PLATE RG5‐1577‐020CN Guide plate (with foam pad attached) RG5‐1691‐000OE FEEDER GUIDE CON FLAG SENSOR LJ 6P RG5‐1713‐000CN Gear drive train plate assembly ‐ 16 gears mounted on side plate RG5‐1786‐000CN Mirror assembly ‐ Top, center of print structure RG5‐1801‐000CN Tubeaxial fan RG5‐1814‐000CN Small media roller assembly ‐ Mounts on the bottom of the plate in the feeder guide assembly RG5‐1875‐000CN Face Up solenoid assembly RG5‐1884‐000CN Multipurpose paper tray board ‐ Includes paper sensors PS1301 and PS1302 RG5‐1888‐000R HVPS ASSEMBLY SEE C3166‐69021 REF RG5‐1915‐040CN Right door assembly ‐ Door below paper tray 1 ‐ Support strap attached to right side RG5‐1945‐000CN INPUT ASSY 2 LJ6L RG5‐1984‐000CN Interlock assembly ‐ Detects if EP (Toner) door is open
2 2 2 1 1 1 1 1 1 1 1 2 1 4 1 15 1 1 2 1 5 1 1 2 10 1 3 1 4 1 1 2 1 4 1
RG5‐2028‐000R CONTROL PANEL LJT 5L/6L RG5‐2044‐000CN High voltage power supply assembly RG5‐2170‐000CN 2000 sheet paper tray paper pickup assembly RG5‐2189‐000OE PAPER OUTPUT ASSY LJT 5 OEM RG5‐2195‐000OE PAPER PICK UP FEEDER LJ 5/4/4+ RG5‐2238‐000R CONTROL PANEL LJT 5 RG5‐2364‐000CN PAPER FEED SENSOR ASSEMB RG5‐2641‐000R LASER SCANNER UNIT‐LJT 4050 RG5‐2645‐000CN Right side top cover support assembly RG5‐2648‐110R DELIVERY ASSEMBLY LASERJET HP REF RG5‐2652‐070R REGISTRATION LJT 4000/N ref RG5‐2653‐000R GEAR TRAIN‐LJT 4050 RG5‐2653‐020CN Print drive gear assembly RG5‐2656‐000OE TRAY 1 ASSEMBLY LJ 4000/4050 RG5‐2776‐000R FAN LJ 6P RG5‐2779‐000CN Power cord cover assembly ‐ Power button and spring included RG5‐2780‐000CN Left side cover assembly ‐ Includes interface connector cover, light pipe block, and infrared filter lens RG5‐2785‐000CN Multi‐Purpose input tray (Tray 1) ‐ Fold down front cover RG5‐2786‐000CN Main motor assembly RG5‐2790‐000CN Paper pickup assembly ‐ Includes pickup roller assembly, guide plate, solenoid, photo sensor (PS5) photo sensor cable, a RG5‐2796‐000CN Paper pickup assembly ‐ Includes D‐shaped pickup roller and solenoid RG5‐2848‐000R Laser/scanner assembly LASER 6P C3980‐69005 RG5‐3008‐000CN Image transfer belt mount RG5‐3046‐020CN Transfer drum lever assembly RG5‐3452‐000CN Transfer guide assembly (Ribbed plastic piece) ‐ Mounting support for the transfer roller RG5‐3521‐020OE Tray 2 paper pickup roller assembly RG5‐3522‐030CN Paper feed roller assembly RG5‐3524‐110OE REGISTRATION ROLLER ASSEMBLY 5000 RG5‐3548‐060CN Transfer guide assembly ‐ Includes the width adjuster for the drop down tray RG5‐3558‐000OE Top of page sensor cable RG5‐3579‐000OE TRANSFER ROLLER LJ5000 RG5‐3821‐000CN Lower tray logic PCA ‐ With tray size switches RG5‐4119‐000CN Delivery roller assembly ‐ Lower face‐down output roller assembly ‐ Includes roller and holder Four used RG5‐4127‐070CN Tray 2 pickup assembly RG5‐4128‐000OE PICKUP ASSY LJT 2100 2200 TRAY 1 OEM
1 1 1 2 1 1 3 3 1 2 9 2 10 14 1 1 1 1 1 3 4 5 1 7 1 2 1 1 1 4 2 1 2 1 11
RG5‐4164‐000OE TRANSFER ROLLER LJ 2100 RG5‐4212‐020CN Feed sensor PC Board ‐ Paper size switch PC board for 500‐sheet feeder RG5‐4250‐000CN Intermediate board ‐ Interconnnect PC board RG5‐4303‐030OE Registration Assembly RG5‐4308‐000OE CLUTCH ELECTROMAGNETIC OEM RG5‐4364‐000CN Toner cartridge guide ‐ Rear guide ‐ Plastic piece with slot to guide toner cartridge RG5‐4365‐000OE ASSY PRINTER DRIVE RG5‐4581‐000OE Paper Feed Assy P/ LJ 1100/3200 RG5‐4585‐000CN Paper pickup shaft drive clutch/gear assembly RG5‐4591‐000CN Pressure roller mount ‐ Left side RG5‐4593‐000OE Delivery Assy RG5‐4599‐000CN Door switch/sensor assembly RG5‐4605‐080OE ECU PCB ‐ Engine contoller unit PC board ‐ 110V RG5‐4653‐000CN SCANNER CONNECTOR ASSY RG5‐4657‐000OE TRANSFER ROLLER LJT 1100 OEM RG5‐4681‐000CN Heating element assembly (For 220V to 240V operation) ‐ Bonds the toner to the paper with heat RG5‐5115‐000CN TRANSFER ASSY KIT LJT 4500 COLOR RG5‐5135‐000OE FACE‐DOWN DELIVERY ASSY LJT 4500 OEM RG5‐5254‐000R PC Board : DC controller board RG5‐5438‐030CN Control panel ‐ Does not include overlay RG5‐5468‐000R PC Board : Cartridge memory controller board ‐ Between ECU and the toner cartridge memory antenna. RG5‐5541‐000CN DELIVERY ROLLER ASSY DOWN LJT 2200 RG5‐5570‐000OE FUSER FILM LASERJET 2200 RG5‐5573‐000OE PWR SPLY ASSY 220‐240V oem RG5‐5623‐000CN 500 Sheet paper tray assembly ‐ Holds 500 sheets of Letter and A4 size paper RG5‐5648‐000CN Left door damper assembly RG5‐5731‐000CN Low Voltage PS 220V RG5‐6467‐000CN MP/Tray 1 assembly ‐ Front drop‐down Multipurpose/Tray 1 assembly RG5‐6583‐000CN ADF separation roller RG5‐7188‐020CN 250‐sheet paper cassette tray assembly ‐ Includes the paper tray assembly with the separation pad, paper width adjusters RG5‐7573‐000CN Fusing assembly ‐ For 220V to 240V AC operation ‐ Bonds the toner to the paper with heat LJ 2550 RG9‐0750‐000CN AC power supply module assembly ‐ 220/240VAC, 50Hz RH6‐0098‐000CN Control panel assembly (220/240V) ‐ Includes display and keypad RH7‐1048‐000CN Main motor assembly RH7‐1094‐000CN Main motor assembly
3 1 1 2 1 1 4 7 1 1 8 1 1 1 1 3 1 1 1 1 1 3 1 1 1 1 1 1 2 1 1 4 2 1 1
RH7‐1122‐000CN Squirrel cage type fan assembly ‐ 24VDC RH7‐1199‐000CN Main motor RH7‐1266‐000R FAN PARA LOW VOLTAGE LJ 8100 RH7‐1289‐000OE Tubeaxial fan RH7‐1334‐000CN Main cooling fan RH7‐1334‐000R MAIN COOLING FAN‐LJT 4050 RH7‐1407‐000OE SMALL FAN LOCATED AT LEFT REAR OF OEM RH7‐1430‐000CN Tubeaxial fan RH7‐5139‐000CN Paper pickup solenoid RH7‐5160‐000CN SOLENOID RH7‐5201‐000CN Clutch Magnetic RH7‐5253‐000CN Solenoid RH7‐7054‐000CN Thermistor assembly ‐ Includes cable RL1‐0013‐000CN Swing plate ‐ Pivot mount for pickup roller shaft RL1‐0303‐000CN Paper pickup roller (D‐shaped roller) ‐ Picks up media from the paper input tray RM1‐0001‐040CNMain drive assembly ‐ Main gear assembly on right side of printer RM1‐0002‐030CNDuplexing pendulum assembly ‐ Gear assembly that transfers power from main motor to run duplexing capability RM1‐0004‐060CNTray 1 paper input assembly RM1‐0007‐000OETRANSFER ASSY OEM RM1‐0027‐020OECOVER, REAR OUTPUT BIN RM1‐0033‐040CNTray 2 lifter drive assembly ‐ Provides lift support for paper tray RM1‐0041‐000CNTRAY 2 PAPER SIZE SENSING ASS RM1‐0041‐020CNTray 2 paper size tray sensing assembly ‐ White plastic tray size sensing fingers and microswitch assembly RM1‐0046‐020CNRight side cover assembly RM1‐0050‐050OEFront cover ‐ Drop down Tray 1 RM1‐0173‐000CNLaser/scanner assembly RM1‐0506‐050CNDC Controller board ‐ Located on rear lower left of printer ‐ For laserJet 3700 only RM1‐0524‐000CNLaser/scanner assembly RM1‐0532‐000CNLift plate assembly ‐ Quartz Gray plastic plate with two Blue paper width adjusters RM1‐0572‐000CNPaper sensor PC board ‐ Small board with optical flag sensor (Flag not included) RM1‐0574‐000CNPaper sensor PC board ‐ Small board with optical flag sensor (Flag not included) RM1‐0629‐000CNPaper input tray assembly ‐ Includes the tray base and pull‐out paper support extension (Dust cover NOT Included) RM1‐1243‐030CNEngine controlunit (ECU) PC board ‐ Control and power supply board for the printer (For 220V to 240V operation) ‐ Does N RM1‐1292‐000CN250‐sheet input paper tray (tray 2) assembly ‐ Includes the tray body and front cover assemblies RM1‐1301‐000CNDouble gear assembly ‐ Includes the gear body, inset gear (both with a toothless area) and compression spring ‐ For driv
12 4 2 1 1 10 1 1 1 1 1 1 3 1 1 1 6 2 2 2 1 1 9 2 1 1 1 1 1 1 1 1 1 2 2
RM1‐1461‐010OEFUSING ASSEMBLY 220V LJ 1160 RM1‐1484‐000OETray 1/MP Tray pickup roller shaft assembly ‐ Includes roller shaft, bushings and pickup roller. RM1‐2048‐000CNSeparation pad assembly ‐ Includes the holder assembly, separation pad, and spring ‐ The assembly is inserted into the b RM1‐2062‐000CNTransfer roller assembly ‐ Steel shaft with black spongy roller and drive gear ‐ P /LJ1022/3050 RM1‐2076‐000OEFusing assembly ‐ Bonds toner to paper with heat ‐ For 220V for LJ 3380 RM1‐2683‐020CNHigh voltage toner contact assembly RM1‐3045‐020CNFusing assembly ‐ Bonds the toner to the paper with heat LJ 3050/3052/3055 RS1‐0287‐000CN Dual gear ‐ 27/21 tooth ‐ On right side of fusing assembly RS5‐0176‐000CN Dual gear ‐ White, 25/33 tooth RS5‐0186‐000CN Gear ‐ Black, 34 tooth RS5‐0187‐000CN Dual gear ‐ Black, 21/40 tooth RS5‐0750‐000OE GEAR,25T,LJ5SI,HP SKU OE RS5‐0753‐000OE New Fuser Gear (48T) OE RS5‐2021‐000CN Compression spring ‐ For arm that holds right side of transfer roller RS5‐2219‐000CN Rear door spring ‐ Fits under rear door latch RS5‐2254‐000CN Compression spring RS5‐2499‐000CN Tension spring ‐ Front spring on metal slide RS5‐2501‐000CN Spring ‐ Located underneath paper kick plate RS5‐2502‐000CN Compression spring ‐ Provides tension for separation pad RS6‐0140‐000CN Gear ‐ 18 tooth RS6‐0149‐020OE GEAR 26T OEM RS6‐0152‐000CN Gear ‐ 29 tooth RS6‐2025‐000CN Tensioning spring RS6‐8057‐000OE LABEL CAUTION OEM RY7‐5006‐000CN Gear kit ‐ Includes first four gears driven by main motor RY7‐5036‐000CN Gear kit '#3' ‐ Includes first four gears driven by main motor RY7‐5050‐000CN Subpad kit ‐ Helps separation of media at pickup roller RY7‐5050‐000OE SUB PAD KIT OEM RY7‐5052‐000CN Transport roller kit ‐ Contains all of the rollers used in the paper transport assembly RY7‐5053‐000CN Transport belt kit ‐ Contains all of the belts used in the paper transport assembly RY7‐5055‐000CN Scanner separation pad kit ‐ Kit includes separation pad, separation backing pad and separation pad holder RY7‐5081‐000CN Gear/clutch assembly kit ‐ Includes double‐gear body, shaft attachment piece and spring WC4‐5139‐000CNTop cover interlock access switch XF9‐0410‐000CN Timing belt Codigo
Descripcion
2 6 11 7 2 1 1 1 3 2 2 1 1 1 1 4 3 1 2 1 2 2 1 2 3 1 1 38 2 1 1 8 1 2 Cantidad
H3975‐60002OE KIT DE MANT. LJ 3100/3150 H3967‐60001TM KIT DE MANT. LJ 6P 220V C2001‐69013TM KIT DE MANT LJ. 4/4M 220V EXCH. H3976‐60002OE KIT DE MANT. LJ 1000/1200/3300 220V RG5‐5456‐000OE FUSOR ASSY LJT 5000 Printer series (220V) RG5‐4448‐000R FUSOR ASSY LJT 5si/8000 Printer series (220V) REF RG5‐0879‐130CN FUSERASSY 120V NEW 5S Codigo
Descripcion
8 3 3 2 4 1 1 Cantidad
RB1‐2127‐000OE ROLLER PICKUP LJ 4 RF5‐3338‐000CN Feed/separation/pickup roller ‐ Rubber roller on a plastic collar with integrated gear and locking tab RB1‐6332‐000OE PICKUP ROLLER LJT 6P 5P TRAY 2 OEM RF5‐0596‐000OE TRANSFER ROLLER LJ 4L/4P/6P OEM RB1‐8794‐000OE PRESSURE ROLLER LJ 4000 OEM RB1‐2650‐000CN Pickup roller (oval shaped) ‐ Located in the lower cassette base assembly RF5‐0596‐000R TRANSFER ROLLER 4L /6P REM H3979‐60001TM Paper path roller kit ‐ Includes pickup D rollers (8 each) , Feed/Sep rollers (4 each) and Tray 1 pickup (8000) RB1‐2632‐000CN Pickup roller (oval shaped) ‐ Located in the lower cassette base assembly RG5‐1834‐000CN Feeder assembly ‐ Transfer roller and registration assembly are mounted on this assembly RB1‐3477‐000OE PICKUP ROLLER LJT 4+ TRAY 2 OE RC1‐0945‐000CN Pickup roller ‐ MP/Tray 1 pickup roller RB1‐6822‐000CN Duplexer roller assembly ‐ Mounts in the center of the duplexer unit Codigo
Descripcion
304860‐001 4.3GB hot‐plug Wide Ultra SCSI‐3 hard drive ‐ 10,000 RPM ‐ Includes 1‐inch, 80‐pin drive tray 242622‐001 4.3GB hot‐plug Wide Ultra SCSI‐3 hard drive ‐ 7,200 RPM ‐ Includes 1‐inch, 80‐pin drive tray 336380‐001 4.3GB hot‐plug Wide Ultra SCSI‐3 hard drive ‐ 10,000 RPM ‐ Includes 1‐inch, 80‐pin drive tray 152189‐001 9GB SCSI Hard Drive 189393‐001 9.1GB universal hot‐plug Wide Ultra3 SCSI hard drive ‐ 15,000 RPM ‐ Includes 1‐inch, 80‐pin drive tray 188122‐B22 18.2GB universal hot‐plug Wide Ultra3 SCSI hard drive ‐ 15,000 RPM ‐ Includes 1‐inch, 80‐pin drive tray 349237‐B21 80.0GB SATA ‐ 1.5GB SATA interface, hot swap hard drive ‐ 7,200 RPM, 1‐inch high 104659‐001 36.4GB hot‐plug Wide Ultra SCSI‐3 hard drive ‐ 7,200 RPM ‐ Includes 1.6‐inch, 80‐pin drive tray D4910‐69001 4.2GB Ultra Wide SCSI hard drive ‐ 7,200 RPM D5039AOE 18.2GB HOT‐SWAP UWIDE SCSI 7200RPM P1215A 18.2GB Ultra3 Wide SCSI LVD hard drive ‐ 7,200 RPM, 3.5‐inch form factor, low profile MDLXST15230WD4.3GB SCSI WD HD
39 37 35 35 31 29 18 14 14 12 8 7 4 Cantidad
1 1 8 5 4 3 2 1 1 1 1 1
A5282‐69003
18.2GB hot‐swap LVD SCSI hard drive module ‐ 10,000 RPM
Precio total del lote U$4455+IVA !!!!!
1
