Transcript
95
NEW PRODUCTS
NEW POWER SUBWOOFER
AMPLIFIERS READY FOR THE ELEMENTS
POWERPUNCH
7
MARINE
SOURCE UNITS & REMOTES
NEW
POWER SLIM
BUYER’S GUIDE CONTENTS
27
7
MOBILE AMPLIFER FAMILIES
15
TECHNOLOGIES AMPLIFIER
17
LINE UP AMPS COMPARED
19
GUTS OF AN AMPLIFIER
27
MOBILE SUBWOOFER FAMILIES
35
TECHNOLOGIES SUBWOOFER
37
LINE UP SUBS COMPARED
40
ANATOMY OF A SUBWOOFER
51
MOBILE SPEAKER FAMILIES
59
TECHNOLOGIES SPEAKER
61
LINE UP SPEAKERS COMPARED
63
FRAMEWORK OF A SPEAKER
75
VEHICLE INTEGRATION PRODUCTS
85
MOTO/MARINE AMPLIFER FAMILIES
94
GUTS OF AN AMPLIFIER
99
MOTO/MARINE SUBWOOFER FAMILIES
103
ANATOMY OF A SUBWOOFER
107
MOTO/MARINE SPEAKER FAMILIES
111
FRAMEWORK OF A SPEAKER
117
MOTO/MARINE SOURCE UNITS AND WIRED REMOTES
121
DNA OF A SOURCE UNIT
127
MOTORCYCLE AUDIO PRODUCTS
51
85
117
©2015 Rockford Corporation. All Rights Reserved. ROCKFORD FOSGATE®, PUNCH®, 3SIXTY® and associated logos where applicable, are registered trademarks of Rockford Corporation in the United States and/or other countries. iPhone and iPod are trademarks of Apple Inc., registered in the U.S. and other countries. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Rockford Corporation is under license. The word Harley-Davidson® is a registered trademark of Harley-Davidson, Inc. and is for reference only. The BMW® name is a registered trademark and is for reference only. All other trademarks are the property of their respective owners. Specifications subject to change without notice. “Made for iPod” and “Made for iPhone mean that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance.
AMPLIFIERS SUBWOOFERS SPEAKERS
UNPRECEDENTED POWER AND CONTROL
YEAR
LIMITED WARRANTY
OHMS
YEAR
dB/OCT
12/24 2 +1 2/1
CROSSOVER SLOPE
FREE* EXTENDED WARRANTY
IMPEDANCE STABILITY
HISTORY OF PERFORMANCE
dB/OCT
12
CROSSOVER SLOPE
YEAR
OHMS
YEAR
1 +1 4/2 LIMITED WARRANTY
FREE* EXTENDED WARRANTY
IMPEDANCE STABILITY
THE PERFECT FIRST STEP
LIMITED WARRANTY
OHMS
AMPLIFIERS AMPLIFIERS
YEAR
dB/OCT
12 1 4/2
CROSSOVER SLOPE
IMPEDANCE STABILITY
*WITH QUALIFYING ROCKFORD FOSGATE INSTALLATION KIT PURCHASE
ALL THE POWER, HALF THE SPACE DELIVERING UNPRECEDENTED POWER AND CONTROL A culmination of over 30 years of pushing the envelope in amplifier design, the Power series of amplifiers takes everything that we’ve learned about power output and heat management and puts it into a single package. With technologies such as our Class AD and BD constant power circuits, Rockford engineers squeeze every drop of power out of these amps they can get. So, not only will your system be the envy of all your friends because it’s the
MODELS SHOWN | T400-2, T2500-1bdCP, T400-4, T1000-4ad
9
2015 BUYER’S GUIDE
loudest, but it’s going to sound amazing to boot. Heat management is always a concern. Too much heat will not only shut down your amp but may eventually kill it. We combat this by using specially designed cast aluminum heat sinks as well as our latest Dynamic Thermal Management circuitry to maximize performance while managing the heat production. Simply put, a cooler amp is a happy amp and will run for a very long time.
After seeing a demand in the marketplace for small chassis amplifiers, our engineers took amplifier design to the next level. They designed amplifiers that could fit in small spaces but also deliver on power and performance. The goal set was to take the elements of our larger chassis Power series amplifiers, along with our latest technology, and put them in a smaller footprint design without sacrificing power or performance. Thus, our Power small chassis amplifiers were born. These amplifiers are built on our proven Class AD and BR circuit designs allowing the amplifiers to be over 40% smaller while producing more power than the comparable full size Power version. Heat is managed with our 3-stage cooling system using forced induction air flow allowing you to really push these amps without concern of overheating.
MODELS SHOWN | T500X1br, T400X2ad
BOOSTED RAIL
PRODUCING MORE POWER THAN EVER BEFORE
IDEAL FOR ALL YOUR MOBILE TOYS
Building on the legacy that began over 35 years ago, we completely redesigned our Punch series. This was not just a refresh of their look but also the perfect time to add-in the latest innovations in amplifier design. With a sleek new style thanks to our brushed, cast aluminum chassis with stealth top mount controls, these new Punch amplifiers truly grab the attention of anyone who sees them.
Rockford’s original small chassis amplifier, the PBR series was developed with a few goals and a select group of customers vehicles in mind. We wanted a small footprint amplifier that produced a lot of power but didn’t put a strain on a vehicles electrical system. We had our eyes on the motorcycle and UTV markets knowing that audio solutions for many of these customers were few and what was available wasn’t the highest in quality.
MODELS SHOWN | P1000X1bd, P400X2, P300X2, P1000X5
11
2015 BUYER’S GUIDE
But of course, these amps are more than just pretty, they’re feature rich and powerful. One such innovation is our CLEAN setup circuit which not only tells you if and when your music is distorting, but simplifies the setup of the amp. This gets you listening to your music that much faster. Power has also been addressed in the new circuit design with all models easily exceeding their rated power which means not only is your music clear, but it can get plenty loud.
MODELS SHOWN | PBR500X1br, PBR300X4
We developed the PBR amps to be ultra-efficient by using the vehicle’s own electrical system for a power supply and developed our patented “boosted rail” circuit that stores energy and then releases it when the demands of the music require it. This means that when you hit the road or the trails, you can enjoy your music knowing it is powered by an amplifier built to Rockford’s high standards.
THE PERFECT STARTING POINT Our prime amplifiers are a great first choice to get you going. Whether you’re looking to get into your first audio system or just looking for a Rockford quality amplifier that isn’t going to break the bank, look no further than the Prime series of amplifiers. Many of the design innovations that we’ve developed over the years, from how to deal with heat to maximizing the efficiency of the power supply, have made their way into the Prime amps allowing us to create a line that is not only high quality, but also at an affordable cost to you, the customer. And, like all Rockford amplifiers, we make sure that these not only meet, but exceed their rated power to ensure that you get every watt possible that you’ve paid your hard earned money for. Incorporating features such as variable crossovers and our famous Punch EQ circuit further completes the package making the Prime amplifiers a perfect choice for your audio system.
MODELS SHOWN | R600X5, R1200-4D, R400-4D
13
2015 BUYER’S GUIDE
T2500-1bdCP
WITH
WITHOUT
Output Power
4000
CONSTANT POWER
3500
U.S. Patent (7,994,857)
3000
2500
Frequency
240
220
200
180
160
140
120
80
100
60
40
20
2000
Music and speakers have a dynamic relationship. As the frequency of music varies, so does the impedance of the speaker. Rockford Fosgate’s Constant Power circuit design actively monitors and increases voltage and current as the speaker’s impedance rises with music. Resulting in up to a 25% increase in total amplifier power.
Products Featuring: CONSTANT POWER
When you make a product purchase that bears the Rockford Fosgate name, you are receiving the technology, engineering, and innovation that has taken over three decades to hone. Our constant desire to push the performance envelope has led us to develop proprietary amplifier topologies and acoustic/electrical technologies that put a spin on the normal and make it Rockford.
+20 +18
DYNAMIC THERMAL MANAGEMENT
+16 +14 +12
PUNCH EQUALIZATION
+10
U.S. Patent (3,883,832)
+8 +6 +4 +2 -0 -2
THERMAL IMAGE WITHOUT
20
50
100
200
500
BASS
Hz
1k
2k
5k
10k 20k
TREBLE
In the early 70’s, Jim Fosgate studied the acoustical properties of automobiles by using a real time analyzer. Jim discovered multiple problems common in all vehicles; a midbass hump, a steep high frequency roll off and reduced bass response. This research lead to adding Punch EQ to Rockford Fosgate amps to help correct the acoustical deficiencies found in the automotive listening environment. The new Punch EQ2 is an on-board equalization circuit that when set to Low-Pass (LP) operation, becomes a variable Bass Boost. When set to High-Pass (HP) operation, it acts as a variable Mid-Bass and Treble Boost. When set to All Pass (AP) operation, both Bass and Treble frequencies are boosted.
Products Featuring: on-board PUNCH EQ
HEATSINK
ALUMINIUM
MOSFET
THERMAL GREASE CERAMIC
MAXIMUM EFFICIENCY HEAT SINK APPLICATION MEHSA3 heat management technology takes heat sink efficiency to a new level. The key was to create a dielectric layer between the ceramic topside and the aluminum base that retains all of the electrical isolation and capacitive coupling of the early material increasing its thermal conductivity. The higher power handling results in a 20% reduction in thermal impedance.
Products Featuring: MEHSA
Our engineers at Rockford Fosgate have developed an award winning cooling design called Thermal Management). This patent pending design seamlessly manages the output and power supply temperatures, while evenly distributing the excess heat across the entire amplifier.
T H E R M A DTM L I M A G(Dynamic E WITH
Products Featuring: DTM
THERMAL IMAGE WITHOUT
THERMAL IMAGE WITH
NON MULTIPLYING ADVANCED DECISION Safe output protection is handled by our proprietary NOMAD circuit. NOMAD is an analog computer designed to calculate the maximum level of safe current allowable for each output device (based on their instantaneous voltage drop). This allows the protection to be much more precise than ever before; offering protection against: • Reverse Polarity • Short Circuit • Thermal • Low Impedance • Under/Over Voltage
Products Featuring: NOMAD
CEA-2006 Power ratings on Rockford Fosgate amplifiers conform to CEA-2006 industry standards. These guidelines mean your amplifier’s output power ratings are REAL POWER numbers, not inflated marketing ratings.
Products Compliant with CEA-2006
4/2/1 The ability to deliver continuous total RMS rated power to the speaker(s) in any impedance ranging between 4 ohm through 1 ohm.
Products Featuring: 4/2/1
C.L.E.A.N. U.S. Patent (8,712,066 B1)
Time and sophisticated test equipment have been replaced with Rockford’s integrated level setting technology called CLEAN (Calibrated Level Eliminates Audible Noise). Using simple LED indicators to identify both signal clipping from the audio source and the output level clipping to the speakers, this precise level set-up eliminates speaker damaging distortion. YOUTUBE.COM/ROCKFORDFOSGATE WATCH DETAILED VIDEOS ON OUR AMPLIFIER TECHNOLOGIES.
15
2015 BUYER’S GUIDE
Products Featuring: CLEAN
CLASS AD - The Rockford Fosgate ad topology brings
CLASS D - High efficiency amplifier design that reduces current consumption from the charging system
RMS
CLASS BR
(Patent 8,212,620) - To achieve higher efficiency with lower distortion, Rockford’s BR topology combines, Cycle-by-Cycle, an indirectly coupled high/ low voltage rail linear topology with a switched high/low voltage linear rail topology. This combination yields an unsurpassed power density (watts per cubic inch).
CLASS AB -
The combination of a class B power output with the class A low distortion attributes make class AB the most common amplifier topology in the electronics industry.
FULL RANGE CLASS D - High efficiency amplifier design that reduces current consumption from the charging system
85%
85%
90%
150-300watts
70%
70%
68%
400-1000watts
400-600watts
83%
85%
CLASS RMS
500-1200watts
EFFICIENCY
CLASS RMS EFFICIENCY
500-1000watts
300-1000watts
1CH / 2CH / 4CH
1 CHANNEL
500-2500watts
400-600watts
2CH / 4CH
our high efficiency BD amplifier design to a full range application. Using our Dynamic Frequency Switching to increase the switching frequency during lower output levels for better signal resolution. Coupled with Post Choke Feedback Filtering to compare the input signal to the output signal at the speaker connector removing any unwanted distortion. These technologies eliminate the inherent switching noise associated with typical class D designs.
The trans•ana topology operates the output stage with its full voltage gain, which allows the input stage to operate from a low voltage regulated supply. The signal is then shifted up in level to the high voltage section by the driver stage which forms an active node at ultrasonic frequencies. This results in a very stable, highly linear operation.
EFFICIENCY
BD topology is more efficient than typical class AB and has lower distortion than class D designs. Rockford BD amplifiers are 75-80% efficient vs. 20-60% efficient class AB amplifiers. Delivering more power from your amplifier with less drain on your vehicles electrical and charging system.
CLASS TA -
CLASS
- The Rockford Fosgate
RMS
(Patent RE40550)
EFFICIENCY
CLASS BD
CLASS
Amplifier topology is the arrangement of parts in an amplifier design. These designs are broken out into ‘classes’. Each class has tradeoffs, making the various classes suited for various applications…like Class D or BD with higher RMS power, but undesirable noise in the higher frequencies making it better suited to power subwoofers.
1CH / 2CH / 4CH
AMPLIFIER PERFORMANCELINEUP TOPOLOGIESEXPLAINED -
500watts
300-500watts
77%
73%
WIDTH
17
2015 BUYER’S GUIDE
WIDTH
WIDTH
WIDTH
DUAL-FAN COOLED
101 GRAMS WIDTH
BOOSTED RAIL
HEIGHT
101 GRAMS
HEIGHT
137 GRAMS
HEIGHT
299 GRAMS
HEIGHT
326 GRAMS
HEIGHT
amplifier cross sections show the amount of heatsink material (Thermal Mass). A greater thermal mass means THERMAL MASS PER INCH - These increased play time and lower device distortion.
TH E G UT S
500WATTS 1000WATTS 1500WATTS 2500WATTS
8.1”
OF AN AMPLIFIER
400WATTS 600WATTS
400WATTS 600WATTS 800WATTS 1000WATTS
Die-Cast Aluminum w/DTM™
Organizing the combination of parts that make up the guts of an amplifier tremendously impacts its performance capabilities. A change in topology type matched with a variation of power supply components deliver a higher power output and enhanced audio quality. Rockford’s proprietary amplifier topologies and electrical technologies in our amplifier lineup will drive your system to new heights.
C-Clamp compression Balanced Differential
2.1”
TO-247 MOSFETs w/MEHSA™ 14.9” Ferrite Core Coated/Booted Transformer, with CONSTANT POWER™
HEAT SINK MOSFETS
• Superior sound quality achieved using audiophile grade components. • Proprietary Dynamic Thermal Management circuit manages heat production allowing you to play harder longer without overheating. • Select models utilize our Constant Power circuit giving you up to 25% more power where you want it when you want it.
TERMINALS RCA
MATERIAL HIERARCHY
GOOD
19
2015 BUYER’S GUIDE
*T1500-1bdCP MODEL SHOWN
POWER SUPPLY
CIRCUIT BOARD
BESt
4 layer 3 oz. Copper Circuit Board
Heat Sink - This heavy outer shell protects the parts inside by transferring away the heat made reproducing an audio signal (music).
500WATTS
Power Supply - A.K.A the transformer, as the name suggests it takes the incoming voltage and converts it to a useable voltage for speakers.
Terminals - These are the connection points for the speakers or subwoofers and the power source(battery) for the amplifier.
RCA - These are the connection points for the audio signal(music) coming from the audio source (radio). RCA connectors are most commonly used.
400WATTS
4.3”
Extruded Aluminum
MOSFETs - A type of transistor used to amplify audio signal(music). You’ll see more of these guys lined up as wattage demands increase.
Circuit Board - Sometimes referred to as the PCB, is used to connect thisto-that through tiny lines of copper across multiple layers of pathways.
400WATTS
7” 1.6”
Molex; Set-Screw or Pigtail Balanced Differential; High-Level Capable with Auto Turn -On TO-220 MOSFETs w/MEHSA™ Ferrite Core Coated/Booted Transformer, with CONSTANT POWER™
• Over 40% smaller than full size Power amps without sacrificing performance. • Maximizes cooling using our forced induction cooling fan system. • Simplified setup using our C.L.E.A.N. circuit technology.
4 layer 2 oz. Copper Circuit Board *T400X2ad MODEL SHOWN
300WATTS 400WATTS 500WATTS 1000WATTS
300WATTS 400WATTS 500WATTS 1000WATTS
400WATTS 600WATTS
250WATTS 500WATTS 750WATTS 1200WATTS
1000WATTS
7.8”
6.8”
600WATTS
Die-Cast Aluminum
C-Clamp compression
Set-Screw
Balanced Differential; High-Level Capable with Auto Turn-On
Balanced Differential; High-Level Capable
Ferrite Core Coated/Booted Transformer 4 layer 2 oz. Copper Circuit Board *P1000X1bd MODEL SHOWN
2.4”
2” TO-220 Bipolar Transistors
300WATTS
13.3”
11.2”
• Built on a legacy over 35 years in the making. • The C.L.E.A.N. setup circuit ensures maximum performance and undistorted output. • Signal inputs can accept either speaker level or RCA level input signals without needing a convertor.
Balanced Differential; High-Level Capable with Auto Turn -On
400WATTS 600WATTS 6.8”
Die-Cast Aluminum Set-Screw
6.5”
Balanced Differential 1.5”
2”
TO-220 MOSFETs w/MEHSA™
TO-220 MOSFETs 11.1”
Storage Capacitor 4 layer 2 oz. Copper Circuit Board *PBR300X1 MODEL SHOWN
2015 BUYER’S GUIDE
2 layer 2 oz. Copper Circuit Board *R250X4 MODEL SHOWN
Extruded Aluminum Molex; Set-Screw or Pigtail
Ferrite Core Transformer
• Custom engineered high mass heat sink design for maximum heat dissipation. • Top mount controls for ease of installation and setup.
300WATTS 4.3”
21
250WATTS 300WATTS
Die-Cast Aluminum w/ DTM™
TO-220 MOSFETs w/MEHSA™
300WATTS 500WATTS
150WATTS
Ferrite Core Transformer 2 layer 2 oz. Copper Circuit Board
• Small chassis, application specific amplifier design accepts speaker level or RCA level input signals. • Perfect for vehicles with low current capable electrical systems. • Three times the power of similar sized A/B models.
• Ultra-efficient 4-channel amplifier design using the latest full range Class D technology. • Amplifiers are optimized for 4-channel front/rear systems.
*R600-4D MODEL SHOWN
Impedance Stability
Protection
150mV - 5V
>105dB
>50dB
H 2.14” x W 8.14” x L11.41” (Small chassis)
T600-2
200x2 @ 4 ohms 300x2 @ 2 ohms 600x1 @ 4 ohms bridged
20Hz - 20kHz
<0.05%
150mV - 5V
>105dB
>50dB
H 2.14” x W 8.14” x L13.66” (Medium chassis)
T400-4
60x4 @ 4 ohms 100x4 @ 2 ohms 200x2 @ 4 ohms bridged
20Hz - 20kHz
<0.05%
150mV - 5V
>105dB
>50dB
H 2.14” x W 8.14” x L13.66” (Medium chassis)
Differential RCA inputs
T600-4
100x4 @ 4 ohms 150x4 @ 2 ohms 300x2 @ 4 ohms bridged
20Hz - 20kHz
<0.05%
150mV - 5V
>105dB
>50dB
H 2.14” x W 8.14” x L14.91” (Large chassis)
Differential RCA inputs and RCA pass thru
150x4 @ 4 ohms 150x4 @ 2 ohms 200x4 @ 1 ohm 300x2 @ 4 ohms bridged 400x2 @ 2 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 5V
>95dB
>50dB
T800-4ad
H 2.14” x W 8.14” x L13.66” (Medium chassis)
Class ad w/ Constant Power
250x4 @ 4 ohms 250x4 @ 2 ohms 250x4 @ 1 ohm 500x2 @ 4 ohms bridged 500x2 @ 2 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 5V
>95dB
>50dB
T1000-4ad
H 2.14” x W 8.14” x L14.91” (Large chassis)
Class ad w/ Constant Power and 4/2/1
T500-1bdCP
300x1 @ 4 ohms 500x1 @ 2 ohms 500x1 @ 1 ohm
20Hz - 250Hz
<0.5%
150mV - 5V
>100dB
N/A
H 2.14” x W 8.14” x L11.41” (Small chassis)
Class bd w/ Constant Power
T1000-1bdCP
700x1 @ 4 ohms 1000x1 @ 2 ohms 1000x1 @ 1 ohm
20Hz - 250Hz
<0.8%
150mV - 5V
>100dB
N/A
H 2.14” x W 8.14” x L13.66” (Medium chassis)
T1500-1bdCP
1000x1 @ 4 ohms 1500x1 @ 2 ohms 1500x1 @ 1 ohm
20Hz - 250Hz
<0.8%
150mV - 5V
>100dB
N/A
H 2.14” x W 8.14” x L14.91” (Large chassis)
1500x1 @ 4 ohms 2500x1 @ 2 ohms 2500x1 @ 1 ohm
20Hz - 250Hz
<0.8%
150mV - 5V
>100dB
N/A
H 2.14” x W 8.14” x L21.9” (X-Large chassis)
T400X2ad
200x2 @ 4 ohms 200x2 @ 2 ohms 400x1 @ 4 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 12V
>110dB
>60dB
H 1.6” x W 4.3” x L7” (Compact chassis)
T400X4ad
100x4 @ 4 ohms 100x4 @ 2 ohms 200x2 @ 4 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 12V
>110dB
>60dB
H 1.6” x W 4.3” x L8.3” (Compact chassis)
T500X1br
175x1 @ 4 ohms 300x1 @ 2 ohms 500x1 @ 1 ohm
20Hz - 220Hz
<1.0%
150mV - 12V
>110dB
N/A
H 1.6” x W 4.3” x L8.3” (Compact chassis)
Class br
P300X2
100x2 @ 4 ohms 150x2 @ 2 ohms 300x1 @ 4 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 12V
>105dB
>50dB
H 2.4” x W 7.8” x L 9.9” (Mini chassis)
TRANS•ana
P400X2
125x2 @ 4 ohms 200x2 @ 2 ohms 400x1 @ 4 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 12V
>105dB
>50dB
H 2.4” x W 7.8” x L 11.0” (Small chassis)
P500X2
150x2 @ 4 ohms 250x2 @ 2 ohms 500x1 @ 4 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 12V
>105dB
>50dB
H 2.4” x W 7.8” x L 13.3” (Medium chassis)
P1000X2
300x2 @ 4 ohms 500x2 @ 2 ohms 1000x1 @ 4 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 12V
>105dB
>50dB
H 2.4” x W 7.8” x L 15.0” (Large chassis)
P400X4
50x4 @ 4 ohms 100x4 @ 2 ohms 200x2 @ 4 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 12V
>105dB
>50dB
H 2.4” x W 7.8” x L 11.0” (Small chassis)
High level capable with auto turn-on balanced differential RCA inputs
75x4 @ 4 ohms 150x4 @ 2 ohms 300x2 @ 4 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 12V
>105dB
>50dB
H 2.4” x W 7.8” x L 13.3” (Medium chassis)
High level capable with auto turn-on balanced differential RCA inputs and RCA pass thru
75x4 + 200x1 @ 4 ohms 125x4 + 400x1 @ 2 ohms N/A + 500x1 @ 1 ohm
20Hz - 20kHz
<1.0%
150mV - 12V
>105dB
>50dB
H 2.4” x W 7.8” x L 15.0” (Large chassis)
TRANS•ana & Class bd
4 layer 2 oz. copper circuit board
12 dB/oct - variable High or Low Pass and All Pass 12 dB/oct - fixed infrasonic
2 ohm stereo / 1 ohm mono rated
NOMAD circuit • Reverse Polarity • Short Circuit • Thermal • Low Impedance • Under/Over Voltage
Focused mass die-cast heatsink / DTM™- Dynamic Thermal Management / MEHSA™- Maximum Efficiency HeatSink Application
P300X1
200x1 @ 4 ohms 300x1 @ 2 ohms
20Hz - 20kHz
<1.0%
150mV - 12V
>105dB
N/A
H 2.4” x W 7.8” x L 9.9” (Mini chassis)
TRANS•ana
4 layer 2 oz. copper circuit board
12 dB/oct - variable High or Low Pass and All Pass
2 ohm mono rated
P400X1
200x1 @ 4 ohms 400x1 @ 2 ohms
20Hz - 20kHz
<1.0%
150mV - 12V
>105dB
N/A
H 2.4” x W 7.8” x L 9.9” (Mini chassis)
Focused mass die-cast heatsink / DTM™- Dynamic Thermal Management / MEHSA™- Maximum Efficiency HeatSink Application
P500X1bd
150x1 @ 4 ohms 300x1 @ 2 ohms 500x1 @ 1 ohm
20Hz - 250Hz
<1.0%
150mV - 12V
>100dB
N/A
H 2.4” x W 7.8” x L 11.0” (Small chassis)
12 dB/oct - variable Low Pass
1 ohm mono rated
NOMAD circuit • Reverse Polarity • Short Circuit • Thermal • Low Impedance • Under/Over Voltage
P1000X1bd
300 @ 4 ohms 600x1 @ 2 ohms 1000x1 @ 1 ohm
20Hz - 250Hz
<1.0%
150mV - 12V
>100dB
N/A
H 2.4” x W 7.8” x L 13.3” (Medium chassis)
Class bd
Additional Features
Focused mass die-cast heatsink / 4-Point Thermal Monitoring / MEHSA™- Maximum Efficiency HeatSink Application
Speaker Terminals
Class ad w/ Constant Power
Focused mass die-cast heatsink / DTM™- Dynamic Thermal Management / MEHSA™- Maximum Efficiency HeatSink Application
Power Terminals
P1000X5
TRANS•ana
RCA Inputs
<0.05%
Heatsink Design
Dimensions
Variable Crossover
Channel Separation
Circuit Board
S/N Ratio
20Hz - 20kHz
Topology
Input Sensitivity
NOMAD circuit • Reverse Polarity • Short Circuit • Thermal • Low Impedance • Under/Over Voltage
THD+N @ Rated Power
1 ohm stereo / 2 ohm mono stable
120x2 @ 4 ohms 200x2 @ 2 ohms 400x1 @ 4 ohms bridged
P600X4
2015 BUYER’S GUIDE
24 dB/oct - variable High or Low Pass and All Pass
T400-2
T2500-1bdCP
23
4 layer 3 oz. copper circuit board
Frequency Response
Rated Power
[ AMPLIFIER SPECIFICATIONS [
4 Ga. c-clamp compression connector
8 Ga. c-clamp compression connector
Punch EQ variable from 0dB to +18dB @ 45Hz and/or 0dB to +12dB @ 12KHz with optional PEQ
Balanced differential RCA inputs and RCA pass thru
4 Ga. c-clamp compression connector
8 Ga. c-clamp compression connector
Punch EQ variable from 0dB to +18dB @ 45Hz with optional Punch Equalization
Balanced differential panel mount RCA and RCA pass thru
stealth proprietary 1/0 Ga. 4mm allen head set-screw cast zinc connector
stealth proprietary 8 Ga. 4mm allen head set-screw cast zinc connector
Punch EQ variable from 0dB to +18dB @ 45Hz with optional Punch Equalization and BDSync or Master/ Slave
High level capable with auto turn-on balanced differential RCA inputs
8 Ga. Quick Connect terminal
16 Ga. 4-pin Molex connector
Punch EQ variable from 0dB to +18dB @ 45Hz and/or 0dB to +14dB @ 12.5KHz with optional Punch Level Control(PLC2)
10 Ga. nickel plated Quick Connect
Punch EQ variable from 0dB to +18dB @ 45Hz with optional Punch Level Control(PLC2)
4 Ga. c-clamp compression connector
8 Ga. c-clamp compression connector
Punch EQ variable from 0dB to +18dB @ 45Hz and/or 0dB to +14dB @ 12.5KHz with optional Punch Level Control(PLC2)
High level capable with auto turn-on balanced differential RCA inputs
4 Ga. c-clamp compression connector
8 Ga. c-clamp compression connector
Punch EQ variable from 0dB to +18dB @ 45Hz and/or 0dB to +14dB @ 12.5KHz with optional Punch Level Control(PLC2)
High level capable with auto turn-on balanced differential RCA inputs and RCA pass thru
4 Ga. c-clamp compression connector
8 Ga. c-clamp compression connector
Punch EQ variable from 0dB to +18dB @ 45Hz and/or 0dB to +14dB @ 12.5KHz with optional Punch Level Control(PLC2)
Balanced differential RCA inputs and RCA pass thru
Differential RCA inputs
Differential RCA inputs and RCA pass thru
4 layer 3 oz. copper circuit board
4 layer 2 oz. copper circuit board
4 layer 2 oz. copper circuit board
24 dB/oct - variable Low Pass
1 ohm mono rated
12 dB/oct - variable High or Low Pass and All Pass
2 ohm stereo / 4 ohm mono rated
12 dB/oct - variable Low Pass
1 ohm mono rated
12 dB/oct - variable High or Low Pass and All Pass
2 ohm stereo / 4 ohm mono rated
NOMAD circuit • Reverse Polarity • Short Circuit • Thermal • Low Impedance • Under/Over Voltage
NOMAD circuit • Reverse Polarity • Short Circuit • Thermal • Low Impedance • Under/Over Voltage
NOMAD circuit • Reverse Polarity • Short Circuit • Thermal • Low Impedance • Under/Over Voltage
Focused mass die-cast heatsink / DTM™- Dynamic Thermal Management / MEHSA™- Maximum Efficiency HeatSink Application
Dual fan forced induction cooling
Focused mass die-cast heatsink / DTM™- Dynamic Thermal Management / MEHSA™- Maximum Efficiency HeatSink Application
High level capable with auto turn-on balanced differential RCA inputs and RCA pass thru
75x4 @ 4 ohms
20Hz - 20kHz
<0.5%
150mV - 11V
>100dB
>50dB
H 1.5” x W 4.25” x L 6.75”
75x1 @ 4 ohms 150x1 @ 2 ohms 300x1 @ 1 ohm
20Hz - 250Hz
<0.2%
150mV - 11V
>105dB
N/A
H 1.5” x W 4.25” x L 6.75”
175x1 @ 4 ohms 300x1 @ 2 ohms 500x1 @ 1 ohm
20Hz - 20kHz
<0.1%
150mV - 11V
>105dB
N/A
H 1.5” x W 4.25” x L 8.25”
R150X2
50x2 @ 4 ohms 75x2 @ 2 ohms 150x1 @ 4 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 12V
>100dB
>50dB
H 2.0” x W 6.8” x L 11.2”
R250X4
40x4 @ 4 ohms 60x4 @ 2 ohms 125x2 @ 4 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 12V
>100dB
>50dB
H 2.0” x W 6.8” x L 11.2”
R300X4
50x4 @ 4 ohms 75x4 @ 2 ohms 150x2 @ 4 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 12V
>100dB
>50dB
H 2.0” x W 6.8” x L 13.2”
R400-4D
75x4 @ 4 ohms 100x4 @ 2 ohms 200x2 @ 4 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 5V
>90dB
>50dB
H 2.0” x W 6.8” x L 9.1”
R600-4D
100x4 @ 4 ohms 150x4 @ 2 ohms 300x2 @ 4 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 5V
>90dB
>50dB
H 2.0” x W 6.8” x L 11.1”
50x4 + 200x1 @ 4 ohms 75x4 + 300x1 @ 2 ohms 150x2 + N/A @ 4 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 12V
>100dB
>50dB
R600X5
R250X1
150x1 @ 4 ohms 250x1 @ 2 ohms
20Hz - 250Hz
<1.0%
150mV - 12V
>100dB
R500X1D
300x1 @ 4 ohms 500x1 @ 2 ohms
20Hz - 250Hz
<1.0%
150mV - 12V
R750-1D
250x1 @ 4 ohms 500x1 @ 2 ohms 750x1 @ 1 ohm
20Hz - 250Hz
<1.0%
R1200-1D
400x1 @ 4 ohms 800x1 @ 2 ohms 1200x1 @ 1 ohm
20Hz - 250Hz
<1.0%
PBR300X4 PBR300X1
PBR500X1
6 layer 2 oz. copper circuit board
12 dB/oct - 80Hz fixed High or Low Pass and All Pass
2 ohm stereo / 4 ohm mono rated
• Reverse Polarity • Short Circuit • Thermal • Low Impedance • Under/Over Voltage
4 layer 2 oz. copper circuit board
Class ab
Single layer 2 oz. copper circuit board
12 dB/oct - variable Low Pass
12 dB/oct - variable High or Low Pass and All Pass
Additional Features
Class br
Speaker Terminals
H 1.5” x W 4.25” x L 6.75”
Power Terminals
Topology
>50dB
RCA Inputs
Dimensions
>100dB
Heatsink Design
Channel Separation
150mV - 11V
Protection
S/N Ratio
<0.5%
Impedance Stability
Input Sensitivity
20Hz - 20kHz
Variable Crossover
THD+N @ Rated Power
100x2 @ 4 ohms 150x2 @ 2 ohms 300x1 @ 4 ohms bridged
PBR300X2
Circuit Board
Frequency Response
Rated Power
[ AMPLIFIER SPECIFICATIONS [ Inter-locking extruded aluminum heatsinks w/ pierced metal recessed badge
RCA/Speaker level pigtailed Molex connector with auto turn-on
10 Ga. Molex connector
16 Ga. pigtailed Molex connector
Optional PEQ variable from 0dB to +18dB @ 45Hz and/or 0dB to +12dB @ 12KHz, variable high-level adjust and 6V DC offset w/ remote out
4 ohm stereo ONLY
Variable high-level adjust and 6V DC offset w/ remote out
1 ohm mono rated
Optional PEQ Variable from 0dB to +18dB @ 45Hz, variable highlevel adjust and 6V DC offset w/ remote out
2 ohm stereo / 4 ohm mono rated
• Short Circuit • Thermal
Focused mass die-cast heatsink
RCA or speaker level pigtailed Molex connector input and RCA pass thru
8 Ga. Molex connector
12 Ga. pigtailed Molex connector
4 Ga. set-screw connector
10 Ga. set-screw connector
RCA input or speaker level pigtailed Molex connector input
Punch EQ selectable from 0dB/+6dB/+12dB @ 45Hz
RCA input and RCA pass thru
Punch EQ variable from 0dB to +18dB @ 45Hz
Full Range Class d
4 layer 2 oz. copper circuit board
H 2.0” x W 6.8” x L 13.2”
Class ab & Class d
Single layer 2 oz. copper circuit board
12 dB/oct - variable High or Low Pass and All Pass
2 ohm stereo / 4 ohm mono rated(Front/Rear) and 2 ohm mono rated(Sub)
• Short Circuit • Thermal
Focused mass die-cast heatsink
RCA input or speaker level pigtailed Molex connector input
4 Ga. set-screw connector
10 Ga. set-screw connector
Punch EQ selectable from 0dB/+6dB/+12dB @ 45Hz(Front/ Rear) and Variable from 0dB to +12dB @ 45Hz(Sub)
N/A
H 2.0” x W 6.8” x L 11.2”
Class ab
Single layer 2 oz. copper circuit board
12 dB/oct - variable Low Pass
2 ohm mono rated
• Short Circuit • Thermal
Focused mass die-cast heatsink
4 Ga. set-screw connector
10 Ga. set-screw connector
>100dB
N/A
H 2.0” x W 6.8” x L 8.5”
Class d
RCA or speaker level pigtailed Molex connector input and RCA pass thru
Punch EQ variable from 0dB to +12dB @ 45Hz and included Punch Level Control(PLC)
150mV - 4V
>100dB
N/A
H 2.0” x W 6.8” x L 9.1”
4 layer 2 oz. copper circuit board
12 dB/oct - variable Low Pass 12 dB/oct - variable infrasonic
1 ohm mono rated
150mV - 4V
>100dB
N/A
H 2.0” x W 6.8” x L 11.1”
RCA input and RCA pass thru
ROCKFORDFOSGATE.COM Don’t forget to use our Woofer Wiring Wizard to properly wire woofers to your amplifier or our Amp Wire Calculator to optimize output with properly sized wire. 25
2015 BUYER’S GUIDE
Punch EQ variable from 0dB to +12dB @ 45Hz
Punch EQ variable from 0dB to +18dB @ 45Hz and included Punch Level Control(PLC)
UNPRECEDENTED POWER AND CONTROL
YEAR
WATTS
3000 ” 1 5 68
UP TO RMS POWER HANDLING
LIMITED WARRANTY
VOICE COIL
XMAX PEAK TO PEAK
M M
HISTORY OF PERFORMANCE
WATTS
600 YEAR
1
LIMITED WARRANTY
32
UP TO RMS POWER HANDLING
2.5
”
M M
VOICE COIL
XMAX PEAK TO PEAK
THE PERFECT FIRST STEP
SUBWOOFERS SUBWOOFERS
YEAR
WATTS
250 ” 1 2 20 LIMITED WARRANTY
M M
UP TO RMS POWER HANDLING
VOICE COIL
XMAX PEAK TO PEAK
DESIGNED WITH THE LATEST WOOFER TECHNOLOGY The power series truly surpasses the competition as your premier woofer choice. Power series subwoofers have always been known for class leading performance, power handling and output capabilities. This year our speaker engineers went back to the drawing board trying to not only improve on the current design but create something entirely new. They far surpassed expectations by not only recreating the T2 series of woofer from the ground up, but also introducing our newest additions to the family; the T3 19” and T1 Slim series of woofers. Whether you loved the old T2 and want to finally step-up to the next level or you feel like you’re grown-up enough to handle our new T3 super woofer monstrosity, we now offer woofers to make the competition and your friends cringe in fear. If you’re tight on space and don’t want to be left out, our new T1 Slim woofer has all the performance and output of our full size T1 with an astounding 3 inch mounting depth. If you’re someone who needs to be the loudest and baddest on the block, then you need the Power series woofers in your ride.
MODELS SHOWN | T3S2-19, T2S1-16, T1D212, T0D212, T1S2-12
29
2015 BUYER’S GUIDE
A PERFECT BALANCE BETWEEN “QUALITY” & “QUANTITY” BASS Punch series woofers are ideal for the customer looking for the best of both worlds. While built on a long standing history of performance, the punch series woofers can deliver not only output to satisfy you when you want it loud but maintain a level of sound quality for when you really want to “listen” to your music. With three series within the family, covering both standard and shallow depth models alike, we have woofers to suit just about anyone’s taste in bass.
OPTIONAL
Taking many design cues from the Power family of products, our speaker engineers continue to improve the series year after year making the Punch family one of the most sought after woofer lines for music and bass enthusiasts alike. With features like our Kevlar reinforced cone assemblies for high strength and anodized aluminum voice coil formers to handle heat buildup in the motor structure under full power situations, these woofers are designed to perform.
ENCLOSURE and / or GRILLE
Optional integrated grille available for ALL PUNCH subwoofers. Loaded enclosures available for all 10” or 12” PUNCH subwoofers and 8”, 10” or 12” PUNCH SHALLOW subwoofers.
MODELS SHOWN | P3D2-12, P2D2-12, P1S2-12, P3SD2-12
31
2015 BUYER’S GUIDE
THE PERFECT FIRST STEP INTO PERFORMANCE AUDIO Are you looking to simply add some bass to your existing audio system? Or better yet, are you wanting to design your first full audio system from the ground up? Are you looking for a woofer that is built with quality and performance in mind and has been designed by the industry’s leading car audio manufacturer? Then our Prime series of woofers are exactly what you are looking for.
OPTIONAL ENCLOSURE Loaded enclosures available for all 10” or 12” PRIME R1 and R2 Shallow subwoofers. Optional integrated grille available for R1 subwoofers.
MODELS SHOWN | R2D2-12, R2SD2-12, R1S4-12
33
2015 BUYER’S GUIDE
Offering both standard depth and shallow mount models, we’ve created a family of woofers that deserves to carry the name Rockford Fosgate. These woofers, like their Punch brethren, are built using many of the same speaker technologies that Rockford has been famous for over 30 years for and you won’t break the bank buying one. Simply put, our Prime series of woofers are held to the same standards of quality and performance as any other Rockford woofer but delivered at an affordable price.
FLEX FIT The slot mounted frame pattern of the Flex Fit basket utilizes slots (where feasible) instead of single screw sized holes. This allows for a slight adjustment of the speaker when mounted. Products Featuring: FLEX FIT SLIM
When you make a product purchase that bears the Rockford Fosgate name, you are receiving the technology, engineering, and innovation that has taken over three decades to hone. Our constant desire to push the performance envelope has lead us to develop proprietary amplifier topologies and acoustic/electrical technologies that put a spin on the normal and make it Rockford.
SHALLOW
SHALLOW
FELX FIT 2 FLEX FIT 2 AND CAR MOUNTING SPEAKER LOCATION
The slot mounted frame pattern allows for variable adjustments to the mounting position, especially for Euro-Fit installations. Products Featuring: FLEX FIT 2
VERTICAL ATTACH SURROUND TECHNIQUE
SLIM
Rockford’s proprietary surround technique, VAST, provides up to a 25% increase in the speaker’s effective radiating cone area without complicated installation issues. This design alters the typical design and manufacturing technique by eliminating the large flat glue surface area (the landing) which allows the surround to be shifted for increased cone area. In turn, both nominal efficiency and maximum output capabilities are dramatically improved. Products Featuring: VAST
SHALLOW
SHALLOW
INDUCTIVE DAMPING HEAT SINK SLIM
SHALLOW
SHALLOW
Secures directly to the top of magnet structure to improve system efficiency by reducing both distortion and back EMF (Electo-magnetic force). Also radiates heat to reduce voice coil temperature. Products Featuring: IDHS
EVCC Our Patent Pending EVCC (Encapsulated Voice Coil Coupling) technology connects to the woofers voice coil from both the top and bottom and provides a more secure mounting platform for both the dual spiders and cone assembly.
SLIM
SHALLOW
SHALLOW
Products Featuring: EVCC SLIM
SHALLOW
SHALLOW
SELECTABLE WOOFER IMPEDANCE FUSED TERMINATION
SYMS The Patent Pending unique motor structure design allows full excursion capabilities of the woofers voice coil while allowing an overall reduction in woofer mounting depth.
Removing and inverting the center plug allows nominal impedance of voice coils to quickly be configured in a Series or Parallel wiring configuration. This removable impedance selection jumper also provides fused protection in severe overload conditions.
Products Featuring: SYMS
Products Featuring: SWIFT SLIM
SHALLOW
SHALLOW
SLIM
SHALLOW
SHALLOW
CEA-2031
VERIFIED WITH KLIPPEL
Power handling on Rockford Fosgate speakers conform to CEA-2031 industry standards. This means your speaker has the capacity to handle power under continuous demand, not instantaneous power handling that over time can damage voice coils.
To adorn the ‘Verified with Klippel’ mark, the qualifying company’s loudspeaker engineering personnel must be trained and certified by Klippel prior to using the three separate Klippel systems to design, develop and test.
Products Compliant with CEA-2031 SLIM
SHALLOW
SHALLOW
• • •
Klippel DA-2 (Designed) Klippel PM-8 (Developed) Klippel QC (Tested)
Products Verified with KLIPPEL YOUTUBE.COM/ROCKFORDFOSGATE WATCH DETAILED VIDEOS ON OUR SUBWOOFER TECHNOLOGIES.
35
2015 BUYER’S GUIDE
SLIM
SHALLOW
SHALLOW
SUBWOOFER PERFORMANCE LINEUP SPL
SPL - Sound Pressure Level numbers reflect an in-car response utilizing dual subwoofers in a typical sedan size cabin at peak power.
XMAX
XMAX - The measured excursion of the subwoofer in one direction, with Peak-to-Peak covering its entire travel. The more air a woofer moves, the higher the SPL.
OUTWARD EXCURSION
PEAK POWER
37
2015 BUYER’S GUIDE
REST
=
INWARD EXCURSION
PEAK POWER - The maximum amount of amplifier power that can be applied to a subwoofer.
a n ato m y OF A SUBWOOFER
Variations in the anatomy of a subwoofer dramatically changes its performance characteristics. An increase in voicecoil size coupled with a stronger cone material yields a higher power handling and increased output. By combining quality materials with Rockford’s proprietary acoustic technologies, our subwoofer lineup is sure to meet your system’s demands.
SURROUND BASKET
CONE
SPIDER VOICE COIL MAGNET
Surround - First part in the speakers suspension, attached to the cone to maintain the centering of the voice coil in the magnetic gap.
Spider - Second part of the speakers suspension, connects the cone and voice coil to the basket and controls the travel of the cone assembly.
Cone - A.K.A the diaphragm, this is the voice of the speaker. Shape and material dramatically change tonality.
Voice Coil - The brains of the operation, directing the force from the magnet to push or pull based on the applied electrical signal.
Magnet - The heart of speaker, creating the force to push and pull cone assembly. Size, material, and design may differ, depending on performance goals.
BESt
GOOD
MATERIAL HIErARCHY
Basket - Also referred to as the frame or chassis, this is the skeletal system of the speaker. Here to keep everything in its place.
RMS POWER RANGE
SINGLE 1Ω SINGLE 2Ω
Injection Molded Foam Surround with VAST™
2000-2500
WATTS
3000
WATTS
SINGLE 1Ω SINGLE 2Ω
RMS POWER RANGE
Injection Molded Foam Surround with VAST™
Specially designed to maximize control and overcome common problems stamp-formed foam surrounds encounter.
Specially designed to maximize control and overcome common problems stamp-formed foam surrounds encounter.
Dual Nomex Progressive Spiders with Integrated Lead Wires
Three-Layer Glass Fiber/ Aramid Honeycomb/ Glass Fiber Cone
Three-Layer Glass Fiber/ Aramid Honeycomb/ Glass Fiber Cone
Extremely rigid yet lightweight cone design eliminates flex under high power applications.
Extremely rigid yet lightweight cone design eliminates flex under high power applications. Dual Nomex Progressive Spiders with Integrated Lead Wires
True NomexTM spiders maximize excursion capabilities while maintaining full linear cone control.
True NomexTM spiders maximize excursion capabilities while maintaining full linear cone control.
Triple Stack Segmented Ferrite Motor Structure Massive motor structure provides necessary magnetic force to maximize output at power handling capabilities.
Stacked Single Layer Edge Wound Aluminum 5” Voice Coil
Dual Gap Multi‐Pole Neodymium Push/Pull Motor Structure
Single layer edge wound design allows for maximum heat dissipation versus multilayer single voice coils.
Innovative dual-gap design drives the voice coil in a custom push/pull configuration for maximum power handling. Massive Neodymium slug provides necessary magnetic force to move the voice coil/ cone assembly to full excursion.
Injection Molded Foam w/ VAST™
5” Single Layer Edge Wound Aluminum
Injection Molded Foam w/ VAST™
4” Single Layer Edge Wound Aluminum
3 Layer Glass Fiber/ Aramid/ Glass Fiber w/ Aluminum Dust Cap
Die-Cast Aluminum w/ Integrated Trim Ring
3 Layer Glass Fiber/ Aramid/ Glass Fiber w/ Aluminum Dust Cap
Die-Cast Aluminum w/ FlexFit2TM
Dual NomexTM Progressive w/ Integrated Leadwires
Dual Gap Multi-Pole Neodymium Push/ Pull
Dual NomexTM Progressive w/ Integrated Leadwires
Triple Stack Ferrite Magnet w/ IDHSTM
*T3S1-19 MODEL SHOWN
41
2015 BUYER’S GUIDE
*T2S1-16 MODEL SHOWN
500-600
WATTS
SINGLE 1Ω SINGLE 2Ω
RMS POWER RANGE
SLIM
DUAL 2Ω DUAL 4Ω
Kevlar fiber cone / Hard Anodized Aluminum Dust Cap Eliminates cone distortion.
600-1000
RMS POWER RANGE
WATTS
Reduces piston flex.
Tall Profile, Santoprene™ w/ VAST™ Kevlar Fiber Paper/ Hard Anodized Aluminum Dual Mirror Imaged w/ Stitched Lead Wire and Cooling Vents
Three-Layer Carbon Fiber/ Rohacell/ Glass Fiber Cone
Injection Molded Foam Surround with VAST™
3” 4-Layer High Temp.Aluminum w/ NomexTM collar
Extremely rigid yet lightweight cone design eliminates flex under high power applications.
Specially designed to maximize control and overcome common problems stamp-formed foam surrounds encounter.
Die-Cast Aluminum w/ FlexFitTM Double Stack Ferrite Magnet w/ IDHSTM
Double Stacked Magnet with IDHSTM
*T1D412 MODEL SHOWN
IDHSTM increases thermal capacity and heat dissipation. This increases power handling and performance.
DUAL 2Ω DUAL 4Ω
Tall profile SantopreneTM w/ VASTTM surround Allows for linear travel. High excursion.
True NomexTM spiders maximize excursion capabilities while maintaining full linear cone control. Innovative suspension design eliminates any mechanical bottoming of the voice coil assembly.
550-800
WATTS
Dual Nomex™ Progressive Spiders with Integrated Lead Wires
High Temp High Energy Neodymium Motor Structure
RMS POWER RANGE
Tall Profile, Santoprene™ w/ VAST™
High quality, high energy neodymium magnet structure provides motor force equivalent to a full size T1 woofer.
Kevlar Fiber Paper/ Hard Anodized Aluminum Dual Mirror Imaged w/ Stitched Lead Wire and Cooling Vents 3” 4-Layer High Temp.Aluminum w/ NomexTM collar
Injection Molded Foam w/ VAST™
3” Dual Wound W/ Interior & Exterior Windings
Die-Cast Aluminum w/ FlexFitTM
3 Layer Carbon Fiber/ Rohacell/ Glass Fiber w/ Aluminum Dust Cap
Die-Cast Aluminum w/ FlexFit2TM
Double Stack Ferrite Magnet
Dual NomexTM Progressive w/ Integrated Leadwires
High Energy Neodymium
*T1S1-12 MODEL SHOWN
43
2015 BUYER’S GUIDE
Die-cast aluminum frame with FlexFitTM For reduced voice coil former temperature and increase power handling. FlexFit for better mounting.
*T0D412 MODEL SHOWN
Hard Anodized Aluminum Cone & Dust Cap
DUAL 2Ω DUAL 4Ω
Premium sound quality. Reduces piston flex. Eliminates cone distortion.
Allows for linear travel.
RMS POWER RANGE
200-250
WATTS
WATTS
500-600
SINGLE 2Ω SINGLE 4Ω
Half Roll, Nitrile Butadiene surround
Tall Profile, Santoprene™ w/ VAST™
RMS POWER RANGE
Half-Roll, Nitrile Butadiene Rubber
Hard Anodized Aluminum
Kevlar Fiber Paper Dual Mirror Imaged w/ Stitched Lead Wire and Cooling Vents
Single w/ Stitched Lead Wire and Cooling Vents
2.50” 4-Layer High Temp. Aluminum w/ NomexTM collar
2” 4-Layer High Temp. Aluminum w/ NomexTM collar
StampCastTM w/ FlexFitTM
Spider Cooling Vents
*P3D4-12 MODEL SHOWN
DUAL 2Ω DUAL 4Ω
Tall profile SantopreneTM w/ VASTTM surround Increased cone area. Allows for linear travel.
WATTS
250-400
RMS POWER RANGE
High excursion.
Single Stack Ferrite Magnet
Flex Fit for better mounting.
*P1S4-12 MODEL SHOWN
DUAL 2Ω DUAL 4Ω
Kevlar Reinforced semipressed Paper Cone Lightweight for efficiency. Very rigid to eliminate cone distortion.
M-Roll Santoprene surround w/ VASTTM
TM
Increased cone area. Lower profile.
Hard Anodized Aluminum Cone & Dust Cap
SHALLOW
Premium sound quality. Reduces piston flex. Eliminates cone distortion.
150-400
RMS POWER RANGE
Tall Profile, Santoprene™ w/ VAST™
M-Roll, Santoprene™ w/ VAST™
Kevlar Fiber Paper
Hard Anodized Aluminum
Dual Mirror Imaged w/ Stitched Lead Wire and Cooling Vents
Dual Laminated w/ Embedded Lead Wire and Cooling Vents
2.25” 4-Layer High Temp. Aluminum w/ NomexTM collar
2.50” 4-Layer High Temp. Aluminum w/ NomexTM collar
StampCastTM w/ FlexFitTM
StampCastTM w/ FlexFitTM
Double Stack Ferrite Magnet
Single Ferrite Magnet
*P2D4-12 MODEL SHOWN
45
Rigid basket.
Proprietary vents work in conjunction with the vented pole piece and vented back plate for maximum cooling & increased power handling.
WATTS
Double Stack Ferrite Magnet
StampCastTM w/ FlexFitTM
StampCastTM frame with Flex FitTM
2015 BUYER’S GUIDE
*P3SD4-12 MODEL SHOWN
Assists in linear cone travel.
WATTS
250
Half-Roll, Sealed Polyether – Ester Foam Surround
RMS POWER RANGE
Improved excursion capabilities.
DUAL 2Ω DUAL 4Ω
Polypropylene Cone Rigid cone reduces piston flex. Reduces cone distortion.
Monolithic Injection Molded Polypropylene Cone Rigid cone design. Reduces cone distortion.
SHALLOW
200-250
WATTS
DUAL 2Ω DUAL 4Ω
Half-Roll, Sealed Polyether-ester Foam
Half-Roll, Sealed Polyether-ester Foam
Polypropylene
Injection Molded Polypropylene
Single w/ Stitched Lead Wire and Cooling Vents
Single w/ Stitched Lead Wire and Cooling Vents
2” 4-Layer High Temp. Aluminum w/ NomexTM collar
2” 4-Layer High Temp. Aluminum w/ NomexTM collar
Stamped Steel
Stamped Steel Frame
Stamped Steel
Design reduces frame flex. Improves performance.
Single Ferrite Magnet *R2D4-12 MODEL SHOWN
WATTS
200
Single Ferrite Magnet *R2SD4-12 MODEL SHOWN
SINGLE 4Ω
RMS POWER RANGE
Half-Roll, Sealed Polyether-ester Foam Polypropylene Single w/ Stitched Lead Wire and Cooling Vents 2” 4-Layer High Temp. Aluminum w/ NomexTM collar Stamped Steel Single Ferrite Magnet *R1S4-12 MODEL SHOWN
47
RMS POWER RANGE
2015 BUYER’S GUIDE
High durability compressed foam surround
Fiber Reinforced Painted Paper-Pulp Cone w/ Aluminum Dustcap
Tear & fatigue resistant.
Rigid & lightweight.
Designed for long life use.
Improves thermal performance for higher power handling.
Mounting Diameter
Mounting Depth
Speaker
Sealed Enclosure (cu. ft.)
Ported Enclosure
Surround Material
Dustcap Material
Cone Material
Voice Coil
3000
6000
17.54"
15.62
0.34
N/A
8 cu. ft. Port: (1) 23"h x 3"w x 30"d
Injection Molded Foam Surround with VAST™
Aluminum Dustcap
Three Layer Glass Fiber/ Aramid Honeycomb/ Glass Fiber
Dual Separated Single Layer Edge Wound Aluminum 5" Voice Coils
T2S1-13/ T2S2-13
13"
Single 1Ω or 2Ω
34
87 dB
2000
4000
12.28"
9.7"
0.34
1.85
4.0 cu. ft. Port: (1) 14"h x 3"w x 20.5"d
T2S1-16/ T2S2-16
16"
Single 1Ω or 2Ω
34
90 dB
2500
5000
15.04"
10.47"
0.49
2.4
5.5 cu. ft. Port: (1) 18"h x 3"w x 23"d
T1D210/T1D410
10”
Dual 2 Ω or 4 Ω
16.4
83 dB
600
1200
9.13"
6.5"
0.203
0.75
1.50 cu ft. Port: (1) 4”x11”
T1D212/T1D412
12”
Dual 2 Ω or 4 Ω
16.4
86 dB
800
1600
11.25"
6.9"
0.308
1.25
1.75 cu ft. Port: (1) 4”x9”
T1D215/T1D415
15”
Dual 2 Ω or 4 Ω
16.4
88 dB
1000
2000
13.94"
8.4"
0.547
2.25
2.66 cu ft. Port: (1) 4”x10”
T1S1-10T1S2-10 SLIM
10”
Single 1 Ω or 2 Ω
15
85 dB
600
1200
11.22"
3.0"
0.05
0.8
1.5 cu. ft. Port: (1) 4"x13
T1S1-12/T1S2-12 SLIM
12”
Single 1 Ω or 2 Ω
15
83 dB
500
1000
9.13"
3.0"
0.03
1.5
2 cu. ft. Port: (1) 4"x14.25"
T0D210/T0D410
10”
Dual 2 Ω or 4 Ω
14.8
81 dB
550
1100
9.13"
6.5"
0.203
0.75
1.50 cu ft. Port: (1) 4”x11”
T0D212/T0D412
12”
Dual 2 Ω or 4 Ω
14.8
84 dB
700
1400
11.25"
6.9"
0.308
1.25
1.75 cu ft. Port: (1) 4”x9”
T0D215/T0D415
15”
Dual 2 Ω or 4 Ω
14.8
87 dB
800
1600
13.94"
8.4"
0.547
2.25
2.66 cu ft. Port: (1) 4”x10”
P3D2-10/P3D4-10
10”
Dual 2 Ω or 4 Ω
13.9
82 dB
500
1000
9.13"
6.2"
0.127
0.59
1.40 cu ft. Port: (1) 4”x14”
P3D2-12/P3D4-12
12”
Dual 2 Ω or 4 Ω
13.9
85 dB
600
1200
11.25"
6.7"
0.194
1.02
1.79 cu ft. Port: (1) 4”x10”
P3D2-15/P3D4-15
15”
Dual 2 Ω or 4 Ω
13.9
86 dB
600
1200
13.94"
7.6"
0.247
1.58
2.66 cu ft. Port: (1) 4”x10”
P3SD2-8/P3SD4-8 SHALLOW
8”
Dual 2 Ω or 4 Ω
8.4
82 dB
150
300
7.13”
2.7”
0.040
0.25
0.75 cu ft. Port: (1) 3”x9”
P3SD2-10/P3SD4-10 SHALLOW
10”
Dual 2 Ω or 4 Ω
8.4
83 dB
300
600
9.13”
3.5”
0.074
0.50
1.00 cu ft. Port: (1) 4”x12”
P3SD2-12/P3SD4-12 SHALLOW
12”
Dual 2 Ω or 4 Ω
8.4
85 dB
400
800
11.25”
3.7”
0.086
1.00
1.25 cu ft. Port: (1) 4”x12”
P2D2-8/P2D4-8
8”
Dual 2 Ω or 4 Ω
7.8
83 dB
250
500
7.13"
4.8"
0.071
0.23
0.65 cu ft. Port: (1) 2”x8”
P2D2-10/P2D4-10
10”
Dual 2 Ω or 4 Ω
11
84 dB
300
600
9.13"
5.9"
0.088
0.59
1.40 cu ft. Port: (1) 4”x14”
P2D2-12/P2D4-12
12”
Dual 2 Ω or 4 Ω
13.3
86 dB
400
800
11.25"
6.4"
0.170
1.02
1.79 cu ft. Port: (1) 4”x10”
P2D2-15/P2D4-15
15”
Dual 2 Ω or 4 Ω
13.3
86 dB
400
800
13.94"
7.3"
0.219
1.58
2.66 cu ft. Port: (1) 4”x10”
8”
Single 2 Ω or 4 Ω
7.6
83.5 dB
200
400
7.13"
4.4"
0.053
0.23
0.65 cu ft. Port: (1) 2”x6”
P1S2-10/P1S4-10
10”
Single 2 Ω or 4 Ω
9.4
85 dB
250
500
9.13"
5.3"
0.085
0.59
1.40 cu ft. Port: (1) 3”x8”
P1S2-12/P1S4-12
12”
Single 2 Ω or 4 Ω
9.4
86 dB
250
500
11.25"
6.0"
0.113
1.02
1.79 cu ft. Port: (1) 3”x6”
P1S2-15/P1S4-15
15”
Single 2 Ω or 4 Ω
9.4
87.5 dB
250
500
13.94"
7.0"
0.191
1.58
2.66 cu ft. Port: (1) 4”x8”
R2D2-10/R2D4-10
10”
Dual 2 Ω or 4 Ω
6.5
89 dB
250
500
9.13"
4.3"
0.101
0.59
1.40 cu ft. Port: (1) 4”x13”
R2D2-12/R2D4-12
12”
Dual 2 Ω or 4 Ω
6.5
87 dB
250
500
11.25"
5.1"
0.150
1.02
1.79 cu ft. Port: (1) 4”x9.3”
R2SD2-10/R2SD4-10 SHALLOW
10”
Dual 2 Ω or 4 Ω
8
83 dB
200
400
9.13"
3.4"
0.037
0.70
1.40 cu ft. Port: (1) 4”x13.7”
R2SD2-12/R2SD4-12 SHALLOW
12”
Dual 2 Ω or 4 Ω
10
85 dB
250
500
11.25"
3.6"
0.039
0.90
1.79 cu ft. Port: (1) 4”x11.8”
R1S4-10
10”
Single 4 Ω
7.0
87 dB
200
400
9.13"
4.4"
0.06
0.75
1.4 cu ft. Port: (1) 3”x8”
R1S4-12
12”
Single 4 Ω
7.0
90 dB
200
400
11.25"
4.94"
0.10
1.02
1.79 cu ft. Port: (1) 3”x6”
P1S2-8/P1S4-8
Aluminum Dia Cast Frame with Integrated Heat Sink Fins and Venting
Dual Gap Multi‐Pole Neodymium Push/Pull Motor Structure
Custom Push Spring Insulated 4 AWG Terminals
Integrated Die Cast Aluminum Trim Ring
Triple Stack Segmented Ferrite Motor Structure
Custom Push Spring Insulated 8 AWG Terminals
Detachable Die Cast Aluminum Trim Ring
Dual Nomex Progressive Spiders
Single Layer Edge Wound Aluminum 4" Voice Coil
Tall profile, Santoprene™ with VAST™
Injection Molded Foam Surround with VAST™
Aluminum Dustcap
Tall profile, Santoprene™ with VAST™
Trim Ring
Peak Power Handling (watts)
90 dB
Terminal Connectors
RMS Power Handling (watts)
34
Motor Structure
Sensitivity
Single 1Ω or 2Ω
Frame Structure
Xmax (mm)
19"
Spider
Nominal Impedance
T3S1-19/ T3S2-19
(cu. ft.)
Speaker Size
Displacement
[ SUBWOOFER SPECIFICATIONS [
Kevlar® fiber reinforced semi-pressed paper
3" 4-layer ultra-high temp. aluminum voice coil with spun-laced Nomex™ insulating reinforcement collar
Dual mirror imaged, progressive roll tear & fatigue resistant poly-cotton spider with multipoint stitched lead wire technique and proprietary spider cooling vents
Die-cast aluminum with FlexFit™
Double stack ferrite magnet with extended vented pole and bumped vented backplate with IDHS™
Dual 10 Ga. proprietary SWIFT™ terminal
Reversible die-cast aluminum w/ Soft Touch paint and integrated/ removable grille
Three Layer Carbon Fiber/Rohacell/ Glass Fiber
Dual Wound Single 3" Voice Coil with Interior and Exterior Windings
Dual Nomex Progressive Spiders
Aluminum Dia Cast Frame with Integrated Heat Sink Fins
High Temp High Energy Neodymium Motor Structure
Custom Push Spring Insulated 10 AWG Terminals
Detachable Die Cast Aluminum Trim Ring
Kevlar® fiber reinforced semi-pressed paper
3” 4-layer ultra-high temp. aluminum voice coil with spun-laced Nomex™ insulating reinforcement collar
Dual mirror imaged, progressive roll tear & fatigue resistant poly-cotton spider with multipoint stitched lead wire technique and proprietary spider cooling vents
Die-cast aluminum with FlexFit™
Double stack ferrite magnet with extended vented pole and bumped vented backplate with IDHS™
Dual 10 Ga. proprietary SWIFT™ terminal
Reversible die-cast aluminum w/ Soft Touch paint and integrated/ removable grille
Hard anodized aluminium
Tall profile, Santoprene™ with VAST™
Hard anodized aluminum
Hard anodized aluminum
2.5" 4-layer ultra-high temp. aluminum voice coil with spun-laced Nomex™ insulating reinforcement collar
Dual mirror imaged, progressive roll tear & fatigue resistant poly-cotton spider with multipoint stitched lead wire technique and proprietary spider cooling vents
StampCast™ with FlexFit™
Double stack ferrite magnet with extended vented pole and bumped vented backplate
8 Ga. custom insulated/isolated compression style
Reversible die-cast aluminum w/ Soft Touch paint and optional integrated grille
M-roll, Santoprene™ with VAST™
Hard anodized aluminum
Hard anodized aluminum
2.5” 4-layer ultra-high temp. aluminum voice coil with spun-laced Nomex™ insulating reinforcement collar
Dual laminated, progressive roll tear & fatigue resistant poly-cotton spiders with embedded lead wire technique and proprietary spider cooling vents
StampCast™ with FlexFit™
Ferrite magnet structure with extended vented pole and bumped vented backplate
8 Ga. custom insulated/isolated compression style
Reversible die-cast aluminum w/ Soft Touch paint and optional grille
Tall profile, Santoprene™ with VAST™
Kevlar fiber reinforced semi-pressed paper
Kevlar® fiber reinforced semi-pressed paper
2.25" 4-layer high temp. aluminum voice coil with spun-laced Nomex™ insulating reinforcement collar
Dual mirror imaged, progressive roll tear & fatigue resistant poly-cotton spider with multipoint stitched lead wire technique and proprietary spider cooling vents
StampCast™ with FlexFit™
Double stack ferrite magnet structure with extended vented pole and bumped backplate
8 Ga. custom insulated/isolated compression style
Reversible die-cast aluminum w/ Soft Touch paint and optional integrated grille
Half-roll, high density Nitrile Butadiene Rubber
Kevlar fiber reinforced semi-pressed paper
Kevlar® fiber reinforced semi-pressed paper
2" 4-layer high temp. aluminum voice coil with spun-laced Nomex™ insulating reinforcement collar
Tear & fatigue resistant polycotton spider with multipoint stitched lead wire technique and proprietary spider cooling vents
StampCast™ with FlexFit™
Ferrite magnet structure with extended vented pole and bumped backplate
8 Ga. custom insulated/isolated compression style
Reversible Acrylonitrile Butadiene Styrene with optional integrated grille
Half-roll, Sealed Polyether-ester foam
Polypropylene
Polypropylene
2" 4-layer high temp. aluminum voice coil with spun-laced Nomex™ insulating reinforcement collar
Tear & fatigue resistant polycotton spider with multipoint stitched lead wire technique and spider cooling vents
Stamped steel
Ferrite magnet structure with extended vented pole and bumped backplate
Standard 10 Ga.
Integrated Polyvinyl Chloride trim ring
Injection molded Polypropylene
Injection molded Polypropylene
Laser-etched aluminum
Fiber re-inforced paper pulp
2" 4-layer high temp. copper voice coil with aluminum former
Integrated ABS
[ SUBWOOFER ENCLOSURE SPECIFICATIONS [ Speaker Model
Nominal Impedance
RMS Power Handling
Peak Power Handling
Dimensions (HxWxD)
P3-2X10
(2) P3D4-10
1Ω
1000 Watts
2000 Watts
13.125” x 31.125” x 15.125”
P3-1X10
(1) P3D2-10
1Ω
500 Watts
1000 Watts
P3-2X12
(2) P3D4-12
1Ω
1200 Watts
2400 Watts
P3-1X12
(1) P3D2-12
1Ω
600 Watts
1200 Watts
P2-2X10
(2) P2D4-10
1Ω
600 Watts
P2-1X10
(1) P2D2-10
1Ω
P2-2X12
(2) P2D4-12
1Ω
P2-1X12
49
(1) P2D2-12
1Ω
2015 BUYER’S GUIDE
Speaker Model
Nominal Impedance
RMS Power Handling
Peak Power Handling
Dimensions (HxWxD)
P1-2X10
(2) P1S4-10
2Ω
500 Watts
1000 Watts
13.125” x 31.125” x 15.125”
13.125” x 17.0” x 15.125”
P1-1X10
(1) P1S4-10
4Ω
250 Watts
500 Watts
13.125” x 17.0” x 15.125”
15.125” x 33.875” x 15.75”
P1-2X12
(2) P1S4-12
2Ω
500 Watts
1000 Watts
15.125” x 33.875” x 15.75”
15.125” x 19.125” x 15.75”
P1-1X12
(1) P1S4-12
4Ω
250 Watts
500 Watts
15.125” x 19.125” x 15.75”
1200 Watts
13.125” x 31.125” x 15.125”
R1-1X10
(1) R1S4-10
4Ω
200 Watts
400 Watts
12.0” x 15.825” x 12.25”
300 Watts
600 Watts
13.125” x 17.0” x 15.125”
R1-2X10
(2) R1S4-10
2Ω
400 Watts
800 Watts
12.0” x 30.0” x 12.25”
800 Watts
1600 Watts
15.125” x 33.875” x 15.75”
R1-1X12
(1) R1S4-12
4Ω
200 Watts
400 Watts
14.0” x 17.5” x 12.25”
15.125” x 19.125” x 15.75”
R1-2X12
(2) R1S4-12
2Ω
400 Watts
800 Watts
14.0” x 33.75” x 12.25”
400 Watts
800 Watts
Speaker Model
Nominal Impedance
RMS Power Handling
Peak Power Handling
Dimensions (HxWxD)
P3S-1X10
(1) P3SD2-10
1Ω
300 Watts
600 Watts
13.5" x 19.0" x 5.3"/3.3"
P3S-1X12
(1) P3SD2-12
1Ω
400 Watts
800 Watts
13.5" x 27.4" x 5.3"/3.3"
Speaker Model
Nominal Impedance
RMS Power Handling
Peak Power Handling
Dimensions (HxWxD)
R2S-1X10
(1) R2SD4-10
2Ω
200 Watts
400 Watts
13.5” x 19.0” x 5.3”/3.3”
R2S-1X12
(1) R2SD4-12
2Ω
250 Watts
500 Watts
13.5” x 27.4” x 5.3”/3.3”
ROCKFORDFOSGATE.COM Don’t forget to use our Woofer Wiring Wizard to properly wire woofers to your amplifier or our Woofer Box Advisor for optimized enclosure bass performance.
150 1
WATTS
UNPRECEDENTED POWER AND CONTROL
UP TO RMS POWER HANDLING
YEAR
LIMITED WARRANTY
40 - 30 Hz
kHz
FREQUENCY RESPONSE
HISTORY OF PERFORMANCE
WATTS
75 1
UP TO RMS POWER HANDLING
YEAR
LIMITED WARRANTY
43 - 22 Hz
kHz
FREQUENCY RESPONSE
THE PERFECT FIRST STEP
SPEAKERS SPEAKERS
YEAR
WATTS
65 1
UP TO RMS POWER HANDLING
LIMITED WARRANTY
47 - 20 Hz
kHz
FREQUENCY RESPONSE
OUTPUT YOU EXPECT, SOUND QUALITY YOU NEVER IMAGINED If you’re truly serious about high quality sound, our Power family of speakers are what you need. Built on years of knowledge in acoustic engineering, Rockford Fosgate delivers a family of speakers that is industry leading. From our class leading T5 series of audiophile components down to our T1 coaxial speakers, the Power family focuses on providing you the best musical experience you’ve ever had. MODELS SHOWN | T5652-S
MODELS SHOWN | T4652-S
MODELS SHOWN | T3652-S
MODELS SHOWN | T2652-S
53
2015 BUYER’S GUIDE
MODELS SHOWN | T1693, T1650-S, T1650, T142
Plus, by incorporating design features such as VAST technology for up to a 25% increase in cone area, which means not only more output for you but a better overall frequency response to our Flex Fit baskets for improved mounting fitment and shorter installation times. The Power family of speakers takes top honors among even the most discerning music aficionados.
WHEN LOUD JUST ISN’T LOUD ENOUGH If you’re someone that really wants to pump up the level of your music to the extreme, then the Punch Pro series of speakers are for you. Rockford Engineers have found that there is a growing community of people who design their audio systems not so much towards sound quality, but more towards sound “QUANTITY”. It’s with this group in mind that led to the development of the Punch Pro speaker family. Designed with high efficiency and high power handling, these speakers are meant to take the power and play loud.
FOR THOSE WHO LIKE IT RAW AND LOUD Are you someone who really likes to “feel” your music? If so then check out the Punch family of speakers. When you’re ready to upgrade and you really want something that can deliver crisp, clear vocals and have the low end response to back them up, then you’ve found them. Using the same VAST technology found on our Power line of speakers, the Punch line is able to produce deeper bass and more volume output than the competition.
With a variety of coaxial and component model speakers ranging in size from 3.5 inches to 6x9 inches, the Punch series is ideal for the customer wanting to roll the windows down, crank the music up and cruise the streets with their buddies.
MODELS SHOWN | PPS4-10, PPS4-6, PP4-NT, PP4-T
HIGH OUTPUT EXTREME LEVELS OF MID TO HIGH RANGE WILL BE EXPERIENCED
SCENARIOS TO CONSIDER WHEN USING THIS PRODUCT: A superior sensitivity yields low power (Watts) requirements. Their unique structure gives opportunity to an equally unique fitment.
MODELS SHOWN | P1694, P1650, P165-SE, P142
55
2015 BUYER’S GUIDE
Available in a variety of tweeter and midrange sizes along with passive crossovers to compliment, Rockford has created a family of products that truly put the phrase “If it’s too loud, then you’re too old” to the test. So, if you want your audio system to not just be at the party, but “BE” the party, then you need to check them out.
It is HIGHLY encouraged to incorporate a generous quantity of this product in one application for a preferred outcome.
To all the Rockford Fosgate Fanatics we would like to introduce the speakers to accompany your two strapped T2500-1bdCP pushing (2) T2 16’s… the PUNCH PRO speakers are guaranteed to provide HIGH OUTPUT full range for extreme SQL (Sound Quantity Level) systems.
AUTHENTIC SOUND AT A PRIME PRICE POINT Are you tired of listening to your factory speakers rattling away inside your doors? Do you want to turn up your factory radio and just get ”more” out of it than you have now? Then you need to check out the Prime family of speakers. Our Prime full range loudspeakers and components are a no-compromise design for that drop-in fit for your factory speaker location. Designed with an ultra-lightweight poly cone and dome tweeter, our Prime drivers are efficient enough to hook up directly to your factory head-unit for instant improvement. If you really want to improve the sound, connect them to an amplifier to increase the speaker’s output and overall performance.
MODELS SHOWN | R`169X3, R165X3, R14X2, R165-S
57
2015 BUYER’S GUIDE
DISCREET DUAL CLAMP Rockford’s proprietary tweeter mounting design provides concentric clamping pressure around the perimeter of the mounting hole, utilizing a single center screw. This applies balanced pressure to both faces of the mounting surface. From there, the tweeter simply snaps into place and is finished with a snap on trim ring. Products Featuring: DDC
When you make a product purchase that bears the Rockford Fosgate name, you are receiving the technology, engineering, and innovation that has taken over three decades to hone. Our constant desire to push the performance envelope has led us to develop proprietary amplifier topologies and acoustic/electrical technologies that put a spin on the normal and make it Rockford.
INDUCTIVE DAMPING HEAT SINK Secures directly to the top of magnet structure to improve system efficiency by reducing both distortion and back EMF (Electo-magnetic force). Also radiates heat to reduce voice coil temperature. Products Featuring: IDHS
VERTICAL ATTACH SURROUND TECHNIQUE Rockford’s proprietary surround technique, VAST, provides up to a 25% increase in the speakers effective radiating cone area without complicated installation issues. This design alters the typical design and manufacturing technique by eliminating the large flat glue surface area (the landing) which allows the surround to be shifted for increased cone area. In turn, both nominal efficiency and maximum output capabilities are dramatically improved. Products Featuring: VAST
RF LINK Rockford’s proprietary RF Link is a bus-power component connection system enabling integration and control of all RF Link equipped products. The use of this systems allows for the expansion of auxiliary controls and managed system turn on. Products Featuring: RFLINK
INTEGRATED CONCEALED CROSSOVER The Integrated Concealed Crossover hides the crossover inside the basket, creating a cleaner look and easier installation. Products Featuring: ICC
FLEX FIT The slot mounted frame pattern of the Flex Fit basket utilizes slots (where feasible) instead of single screw sized holes. This allows for a slight adjustment of the speaker when mounted. Products Featuring: FLEX FIT
CEA-2031 Power handling on Rockford Fosgate speakers conform to CEA-2031 industry standards. This means your speaker has the capacity to handle power under continuous demand, not instantaneous power handling that over time can damage voice coils. Products Compliant with CEA-2031
FLEX FIT 2 AND CAR MOUNTING SPEAKER LOCATION
FELX FIT 2
VERIFIED WITH KLIPPEL
The slot mounted frame pattern allows for variable adjustments to the mounting position, especially for Euro-Fit installations.
To adorn the ‘Verified with Klippel’ mark, the qualifying company’s loudspeaker engineering personnel must be trained and certified by Klippel prior to using the three separate Klippel systems to design, develop and test.
Products Featuring: FLEX FIT 2
YOUTUBE.COM/ROCKFORDFOSGATE WATCH DETAILED VIDEOS ON OUR SPEAKER TECHNOLOGIES.
59
2015 BUYER’S GUIDE
• • •
Klippel DA-2 (Designed) Klippel PM-8 (Developed) Klippel QC (Tested)
Products Verified with KLIPPEL
SPEAKER PERFORMANCE LINEUP Accuracy Score - Is derived from calculating the magnitude deviations from the speaker’s frequency response against a reference flat magnitude response.
ACCURACY SCORE FREQ. RESPONSE RANGE PEAK POWER
Frequency Response Range - The frequency response range or width tells you how high or low the speaker plays. BASS
=
MID
HIGH
Peak Power - The maximum amount of amplifier power that can be applied to a speaker prior to entering into an unsafe operating scenario.
62
f r a m e wo r k
2WAY 6.5” COMPONENTS
OF A SPEAKER
1”(25mm) Liquid Crystal Polymer Fiber Ring Radiator Dome, Dual Neodymium Magnets w/ IDHS™, Low Resonant Chamber and DDC™
Modifications to the framework of a speaker significantly impact its sonic signature. Combining various materials will strengthen, add volume and resonate the music to a desired sound. By intertwining superior speaker designs with Rockford’s proprietary acoustic technologies in our speaker lineup, we are sure to bring your music to life.
RFLink™ Equipped External Component Crossover w/ 1% Mil-Spec Parts and I elligent Protection w/ Integrated/Remote Tuning Module Butyl Rubber w/ VAST™
SURROUND
Tri-laminate Liquid Crystal Polymer Fiber w/ Machined Copper Phase Plug
CONE • Designed and engineered to produce the highest level of sound quality for the most discerning audiophile. • Our custom passive/ active crossover allows you to fine tune the system to suit your taste using the integrated remote control. • The solid copper heat sink and phase plug draw heat away from the voice coil improving sound quality and increasing power handling.
TWEETER
Die-Cast Aluminum w/ FlexFitTM Multi-Pole™ Dual Neodymium Magnet w/ IDHS™ *T5652-S MODEL SHOWN
BASKET CROSSOVEr
2WAY 6.5”
MAGNET COMPONENTS
MATERIAL HIErARCHY
BESt
GOOD
63
2015 BUYER’S GUIDE
Tweeter - Composed of the same parts as an speaker, surround, cone, voice coil, basket and magnet. Just on a smaller scale.
Cone - A.K.A the diaphragm, this is the voice of the speaker. Shape and material dramatically change tonality.
Crossover - Works like a switch board, directing the audio signal through caps, filters and switches to the appropriate speaker.
Basket - Also referred to as the frame or chassis, this is the skeletal system of the speaker. Here to keep everything in their place.
Surround - Works in harmony with the spider, attached to the cone to maintain the centering of the voice coil in the magnetic gap.
Magnet - The heart of speaker, creating the force to push and pull cone assembly. Size, material, and design may differ, depending on performance goals.
1”(25mm) Liquid Crystal Polymer Fiber Ring Radiator Dome, Dual Neodymium Magnets w/ IDHS™, Low Resonant Chamber and DDC™ External Audiophile Grade ComponentCrossover w/ 5% (Tol) Parts Butyl Rubber w/ VAST™ Tri-laminate Liquid Crystal Polymer Fiber
• The T4 components are highly accurate in their frequency reproduction by utilizing the same tweeter, basket and motor structure from the T5. components combined with the cone and crossover from the T3 components. • The multi-pole Neodymium motor structure maximizes excursion capability and control under extreme output conditions. • The Liquid Crystal polymer Fiber cone is lightweight and rigid which improves sound quality and output without distorting cone flex.
Die-Cast Aluminum w/ FlexFitTM Multi-Pole™ Dual Neodymium Magnet w/ IDHS™ *T4652-S MODEL SHOWN
2WAY 6.5”
2WAY 6.75” 6.5” COMPONENTS 6.0” 5.25” Tweeter Kit
COMPONENTS
1”(25mm) Liquid Crystal Polymer Fiber Dome w/ Neodymium Magnet and DDC™
1”(25mm) Treated Fabric Dome w/ Neodymium Motor and DDC™
External Audiophile Grade Component Crossover w/ 5% (Tol) Parts
External Audiophile Grade Component Crossover w/ 5% (Tol) Parts
Butyl Rubber w/ VAST™
Butyl Rubber w/ VAST™
Woven Liquid Crystal Polymer Fiber
Injection Molded Polypropylene-Carbon Fiber Blend
Die-Cast Aluminum w/ FlexFitTM
StampCastTM w/ FlexFitTM and FlexFit2TM
Neodymium Magnet w/ IDHS™ *T3652-S MODEL SHOWN
COMPONENTS
• Our LCP tweeter with silk surround provides clean, crisp high frequency reproduction without worrying about distortion at higher volumes. • Our components feature our discrete Dual Clamping system for the tweeters which provides for a more secure installation than other clamping designs. • The crossover network features bi-amp capabilities if your system calls for amplifying the tweeter separate from the midrange speaker.
• Our FlexFitTM and FlexFit 2TM mounting hole patterns improve the fitment of our speakers as well as expand the number of vehicles the speakers will fit in. (Also found on T1650 Coax). • The 1” fabric dome tweeter provides natural sounding high frequencies while the midrange delivers the lows with precision.
2WAY 6.5” 5.25” Tweeter Kit
Blutyle Rubber w/ VAST™
Injection Molded Polypropylene-Carbon Fiber Blend w/ Machined Aluminum Phase Plug
Injection Molded Mineral Filled Polypropylene w/ Carbon Fiber Blend
StampCastTM w/ FlexFitTM
2015 BUYER’S GUIDE
2WAY 6x9” 6x8” 5x7” 4x6”
ICC™ Component Crossover w/ 5% (Tol) Parts
Butyl Rubber w/ VAST™
65
2WAY 6.75” 6.5” 6.0” 5.25” 4.0”
1”(25mm) Aluminum Dome w/ Neodymium Motor
External Audiophile Grade Component Crossover w/ 5% (Tol) Parts
*T2652-S MODEL SHOWN
*T1675-S MODEL SHOWN
COAXIALS
1”(25mm) Aluminum Dome w/ Neodymium Motor and DDC™
Neodymium Magnet w/ IDHS™
Single Ferrite Magnet
StampCastTM w/ FlexFitTM and FlexFit2TM • Our injection molded, carbon fiber reinforced cone assembly reduces cone flex while maintaining sound quality. • Our midrange speakers utilize our VASTTM technology, which can provide for up to 25% more cone area meaning better frequency response and increased output. • Our StampCastTM aluminum basket design provides a rigid framework and eliminates frame flex under high power applications.
• Our offset cantilever mounted tweeter (select models) eliminates damaging acoustic reflections between the midrange and the rear of the tweeter. • A perfect choice to replace your factory speaker and attain high quality sound output without needing extensive modification to the vehicle.
Single Ferrite Magnet *T1650 MODEL SHOWN
3WAY 6x9”
COMPONENTS
TWEETER 1.0” 4Ω 8Ω
2WAY 6.75” 6.5” 6.0” 5.25” Tweeter Kit
1”(25mm) Horn Design w/ Machined Aluminum Phase Plug
1”(25mm) Plated Polyether Imide (PEI) Dome w/ Neodymium Motor and DDC™
Integrated High-Pass Crossover
ICC™ Component Crossover w/ 10% (Tol) Parts
N/A
Nitrile Butadiene Rubber w/ VAST™
N/A
Injection Molded Mineral Filled Polypropylene StampCastTM w/ FlexFitTM and FlexFit2TM
Die-Cast Aluminum • Punch components feature both FlexFitTM and FlexFit 2TM basket designs for improved factory mounting compatibility (Also found on P1650 Coax). • Most models feature an integrated concealed crossover system so there is no additional crossover box to install.
Single Ferrite Magnet
• Our 1 inch horn loaded tweeter is designed for high SPL applications. • The Neodymium motor structure and cast aluminum housing allows for a compact design for tight spaces.
*PP4-NT MODEL SHOWN
*P1675-S MODEL SHOWN
COAXIALS
Neodymium Magnet w/ IDHSTM
2WAY 6.5” 6x9” 6.0” 5x7” 5.25” 4x6” 4.0” 3.5”
TWEETER 1.5” 4Ω 8Ω
3WAY 6.75” 6x9” 6x8” 4WAY 6x9”
1.5”(38mm) Horn Design w/ Machined Aluminum Phase Plug 1”(25mm) Plated Polyether Imide (PEI) Dome w/ Neodymium Motor and DDC™
Integrated High-Pass Crossover N/A
ICC™ w/ 10% (Tol) Parts
N/A
Nitrile Butadiene Rubber w/ VAST™
Die-Cast Aluminum w/ FlexFitTM
Injection Molded Mineral Filled Polyprpylene StampCastTM w/ FlexFitTM and FlexFit2TM Single Ferrite Magnet *P1650 MODEL SHOWN
67
2015 BUYER’S GUIDE
• Punch coax speakers are ideal for the customer who likes to really “feel” their music. • A perfect “step-up’’ choice when looking to design an amplified speaker system to replace your worn out factory speakers.
• With its oversized motor structure and high temperature voice coil our 1.5 inch Pro tweeter is designed for high SPL systems.
Single Ferrite Magnet *PP4-T MODEL SHOWN
MIDRANGE 6.0” 4Ω 8.0” 8Ω 10.0”
COMPONENTS
N/A
1”(25mm) Mylar Balanced Dome
N/A
Integrated High-Pass Crossover
W-Style, Treated Cloth
SPE Foam
Fiber Reinforced Paper w/ Machined Aluminum Phase Plug
Vacuum Formed Polypropylene
StampCastTM w/ FlexFitTM
Stamped Steel • High efficiency driver designed for extreme output capabilities. • The fiber reinforced cone with machined aluminum phase plug creates a highly sensitive speaker that can handle plenty of power.
Single Ferrite Magnet *PPS4-6 MODEL SHOWN
• A dedicated 2-way component system utilizing a Mica injected polypropylene cone for extended frequency response and accommodates direct OEM installation. • The Mylar balanced dome tweeter recreates crystal clear highs and comes with an in-line crossover for simplified installation.
Single Ferrite Magnet *R165-S MODEL SHOWN
CROSSOVER 4Ω 8Ω
COAXIALS
2WAY 6.75” 5.25” 4.0” 6x9” 6x8”
3WAY 6.5” 6x9”
N/A
1/2”(13mm) Embedded Phase Coherent Mylar Balanced Dome
External Audiophile Grade Component Crossover w/ 5% (Tol) Parts
Integrated High-Pass Crossover
N/A
Nitrile Butadiene Rubber
N/A
Vacuum Formed Polypropylene
N/A
Stamped Steel
N/A *PP4-X MODEL SHOWN
69
2WAY 6.75” 6.5” 6.0” 5.25” Tweeter Kit
2015 BUYER’S GUIDE
Single Ferrite Magnet • Punch Pro crossover is designed to work with our Pro tweeters and midrange speakers. • Available in a 4 or 8 ohm model. • Allows connection of multiple midrange speakers to a single crossover.
• The basket design allows for that perfect factory replacement fit. • Their high efficiency design works great with radio or amplifier power.
*R1675X2 MODEL SHOWN
71
2015 BUYER’S GUIDE
2.48”
T4652-S
6.5”
1”
150 watts
300 watts
40Hz-30kHz
89dB
92dB
2.79”
T3652-S
6.5”
1”
125 watts
250 watts
48Hz-24kHz
87dB
90dB
2.48”
T252-S
5.25”
1”
75 watts
150 watts
65Hz-22kHz
87dB
90dB
1.97”
T2652-S
6.5”
1”
100 watts
200 watts
50Hz-22kHz
88dB
91dB
2.48”
T2T-S
N/A
1”
100 watts
200 watts
3kHz-22kHz
90dB
93dB
*0.91”
T152-S
5.25”
1”
75 watts
150 watts
65Hz-22kHz
87dB
90dB
1.99”
T16-S
6.0”
1”
80 watts
160 watts
60Hz-22kHz
86dB
89dB
1.93”
T1650-S
6.5"
1"
80 watts
160 watts
47Hz - 20kHz
88 dB
91 dB
2.52"
T1675-S
6.75”
1”
100 watts
200 watts
55Hz-22kHz
89dB
92dB
2.51”
T1T-S
N/A
1”
100 watts
200 watts
3kHz-22kHz
90dB
93dB
*0.91”
T142
4”
0.75”
40 watts
80 watts
85Hz-22kHz
86dB
89dB
1.79”
T152
5.25”
1”
60 watts
120 watts
65Hz-22kHz
86.5dB
89.5dB
1.99”
T16
6.0”
1”
70 watts
140 watts
65Hz-22kHz
88dB
91dB
1.93”
T1650
6.5"
1"
75 watts
150 watts
44Hz - 20kHz
88 dB
91 dB
2.52"
T1675
6.75”
1”
75 watts
150 watts
50Hz-22kHz
89dB
92dB
2.51”
T1462
4”x6”
0.75”
45 watts
90 watts
75Hz-22kHz
85.5dB
88.5dB
2.00”
T1572
5”x7”
1”
70 watts
140 watts
60Hz-22kHz
87dB
90dB
2.35”
T1682
6”x8”
1”
80 watts
160 watts
55Hz-22kHz
88dB
91dB
2.60”
T1692
6”x9”
1”
100 watts
200 watts
50Hz-22kHz
90dB
93dB
3.39”
T1693
6”x9”
1”
100 watts
200 watts
50Hz-22kHz
91dB
94dB
3.39”
P152-S
5.25”
1”
50 watts
100 watts
70Hz-22kHz
87dB
90dB
1.91”
P16-S
6.0”
1”
60 watts
120 watts
60Hz-22kHz
87.2dB
90.2dB
1.93”
P165-SE
6.5"
1"
60 watts
120 watts
43Hz - 20kHz
88 dB
91 dB
2.24"
P165-SI
6.5"
1"
60 watts
120 watts
44Hz - 20kHz
88 dB
91 dB
2.24"
P1675-S
6.75”
1”
60 watts
120 watts
55Hz-22kHz
89dB
92dB
2.24”
P1T-S
N/A
1”
60 watts
120 watts
3.5kHz-22kHz
90dB
93dB
*0.91”
P132
3.5”
0.5”
20 watts
40 watts
120Hz-22kHz
85dB
88dB
1.46”
P142
4”
0.75”
30 watts
60 watts
100Hz-22kHz
86.5dB
89.5dB
1.75”
P152
5.25”
0.75”
40 watts
80 watts
70Hz-22kHz
87dB
90dB
1.91”
P16
6.0”
0.75”
55 watts
110 watts
65Hz-22kHz
88dB
91dB
1.93”
P1650
6.5"
0.75"
55 watts
110 watts
45Hz - 20kHz
88 dB
91 dB
2.24"
P1675
6.75”
0.75”
60 watts
120 watts
60Hz-24kHz
89dB
92dB
2.24”
P1462
4”x6”
0.75”
35 watts
70 watts
90Hz-22kHz
87.5dB
90.5dB
1.89”
P1572
5”x7”
0.75”
60 watts
120 watts
75Hz-22kHz
89dB
92dB
2.30”
P1683
6”x8”
0.75”
65 watts
130 watts
65Hz-24kHz
90dB
93dB
2.32”
P1692
6”x9”
0.75”
75 watts
150 watts
60Hz-22kHz
91dB
94dB
3.07”
Butyl rubber with VAST™
Tri-laminate Liquid Crystal Polymer Fiber w/ machined copper phase plug
Nomex™ w/ balanced stitched woven embedded fiber/flat lead wires
Die-cast aluminum with FlexFit™
Multi-pole™ dual neodymium magnet w/ IDHS™
1"(25mm) Liquid Crystal Polymer Fiber ring radiator dome, dual neodymium magnets w/ IDHS™, low resonant chamber and DDC™
Single chassis stereo w/ audiophile 1% mil-spec components and dual micro-controller for intelligent protection w/ integrated/remote tuning module and RFLink™ equipped
3-way connection terminal
Cat 5 remote extension cable, grilles and mounting hardware
Tri-laminate Liquid Crystal Polymer Fiber™
Nomex™ w/ balanced stitched woven embedded fiber/flat lead wires
Die-cast aluminum with FlexFit™
Multi-pole™ dual neodymium magnet w/ IDHS™
1”(25mm) Liquid Crystal Polymer Fiber ring radiator dome, dual neodymium magnets w/ IDHS™, low resonant chamber and DDC™
External audiophile grade component crossover w/ 5% (Tol) parts
3-way connection terminal
Grilles and mounting hardware
Woven Liquid Crystal Polymer Fiber™
Nomex™ w/ balanced stitched woven embedded fiber/flat lead wires
Die-cast aluminum with FlexFit™
Neodymium magnet w/ IDHS™
1"(25mm) Liquid Crystal Polymer Fiber™ dome w/ neodymium magnet and DDC™
External audiophile grade component crossover w/ 5% (Tol) parts
3-way connection terminal
Grilles and mounting hardware
Injection molded Polypropylene-carbon fiber blend w/ machined aluminum phase plug
Fatigue resistant polycotton linear spider w/ woven fiber reinforced lead wire
StampCast™ with Flex-fit™
Ferrite magnet structure
1”(25mm) aluminum dome w/ neodymium motor and DDC™
External audiophile grade component crossover w/ 5% (Tol) parts
Unified tab
Multi-OEM™ adaptor plates, grilles and mounting hardware
18 Ga. Pigtail
Flush w/ DDC™, surface and angle mounting hardware
External audiophile grade component crossover w/ 5% (Tol) parts
Unified tab
Multi-OEM™ adaptor plates, grilles and mounting hardware
External audiophile grade component crossover w/ 5% (Tol) parts
18 Ga. Pigtail
Flush w/ DDC™, surface and angle mounting hardware
Aluminum dome w/ integral suspension & tuned chamber Injection molded Polypropylene-carbon fiber blend
Neodymium
Fatigue resistant polycotton linear spider w/ woven fiber reinforced lead wire
StampCast™ with Flex-fit™
Treated fabric dome w/ integral suspension & tuned chamber
Ferrite magnet structure
1”(25mm) treated fabric dome w/ neodymium motor and DDC™
Neodymium
Accessories
91.5dB
Terminal Connectors
Mounting Depth
88.5dB
Crossover
Sensitivity (2.83V/1M)
45Hz-40kHz
Tweeter
Sensitivity (1W/1M)
300 watts
Motor Structure
Frequency Response
150 watts
Frame Structure
Peak Power Handling (watts)
1”
Spider
RMS Power Handling (watts)
6.5”
Cone Material
Tweeter Size
T5652-S
Surround Material
Speaker Size
[ SPEAKER SPECIFICATIONS [
Butyl rubber with VAST™
Injection molded Polypropylene-carbon fiber blend
Fatigue resistant polycotton linear spider w/ woven fiber reinforced lead wire
StampCast™ with Flex-fit™
Ferrite magnet structure
1”(25mm) aluminum dome w/ neodymium motor and DDC™
ICC™ component crossover with 5% (Tol) parts
Unified tab
Multi-OEM™ adaptor plates, grilles and mounting hardware
Nitrile Butadiene Rubber with VAST™
Injection molded mineral filled Polypropylene
Fatigue resistant polycotton linear spider w/ woven fiber reinforced lead wire
StampCast™ with Flex-fit™
Ferrite magnet structure
1”(25mm) plated Polyether Imide (PEI) dome w/ neodymium motor and DDC™
ICC™ component crossover with 10% (Tol) parts
Unified tab
Multi-OEM™ adaptor plates, grilles and mounting hardware
External component crossover w/ 10% (Tol) parts
18 Ga. Pigtail
Flush w/ DDC™, surface and angle mounting hardware
ICC™ with 10% (Tol) parts
Unified tab
Multi-OEM™ adaptor plates, grilles and mounting hardware
Plated Polyether Imide (PEI) dome Nitrile Butadiene Rubber with VAST™
Injection molded mineral filled Polypropylene
Neodymium Fatigue resistant polycotton linear spider w/ woven fiber reinforced lead wire
StampCast™ with Flex-fit™
Ferrite magnet structure
3/4”(20mm) pole mounted plated Polyether Imide (PEI) dome w/ neodymium motor
3.07”
PPS4-6
6.5”
N/A
100 watts
200 watts
85Hz-5kHz
92.5dB
95.5dB
2.24”
PPS8-6
6.5”
N/A
100 watts
200 watts
87Hz-5kHz
91.5dB
94.5dB
2.24”
PPS4-8
8.0”
N/A
125 watts
250 watts
80Hz-5kHz
94.5dB
97.5dB
2.91”
PPS8-8
8.0”
N/A
125 watts
250 watts
82Hz-5kHz
93dB
96dB
2.91”
PPS4-10
10.0”
N/A
350 watts
700watts
40Hz-3kHz
95dB
98dB
4.17”
PPS8-10
10.0”
N/A
350 watts
700watts
40Hz-3kHz
95dB
98dB
4.17”
PP4-NT
N/A
1"
50 watts
100 watts
4kHz 20kHz
107 dB
110 dB
2.57"
PP8-NT
N/A
1"
50 watts
100 watts
4kHz 20kHz
107 dB
110 dB
2.57"
PP4-T
N/A
1.5”
50 watts
100 watts
3kHz-20kHz
103dB
106dB
2.59”
PP8-T
N/A
1.5”
50 watts
100 watts
3kHz-20kHz
103dB
106dB
2.59”
R152-S
5.25”
1”
40 watts
80 watts
58Hz-20kHz
85dB
88dB
1.91”
R16-S
6.0”
1”
40 watts
80 watts
60Hz-20kHz
89dB
92dB
1.97”
R165-S
6.5”
1”
40 watts
80 watts
60Hz-20kHz
89dB
92dB
1.97”
R1675-S
6.75”
1”
40 watts
80 watts
55Hz-20kHz
89dB
92dB
2.00”
R1T-S
N/A
1”
40 watts
80 watts
2.5kHz-22kHz
72.5dB
75.5dB
*0.76”
R14X2
4”
0.5”
30 watts
60 watts
100Hz-20kHz
85dB
88dB
1.72”
R1525X2
5.25”
0.5”
40 watts
80 watts
62Hz-20kHz
88dB
91dB
1.93”
R165X3
6.5”
0.5”
45 watts
90 watts
52Hz-20kHz
91dB
94dB
2.15”
R1675X2
6.75”
0.5”
45 watts
90 watts
52Hz-20kHz
91dB
94dB
2.19”
R168X2
6”x8”
0.5”
55 watts
110 watts
51Hz-20kHz
87dB
91dB
2.54”
R169X2
6”x9”
0.5”
65 watts
130 watts
48Hz-20kHz
90dB
93dB
2.85”
R169X3
6”x9”
0.5”
65 watts
130 watts
47Hz-20kHz
90dB
93dB
2.85”
Accessories
94dB
Terminal Connectors
Mounting Depth
91dB
Crossover
Sensitivity (2.83V/1M)
60Hz-24kHz
Nitrile Butadiene Rubber with VAST™
Injection molded mineral filled Polypropylene
Fatigue resistant polycotton linear spider w/ woven fiber reinforced lead wire
StampCast™ with Flex-fit™
Ferrite magnet structure
3/4”(20mm) pole mounted plated Polyether Imide (PEI) dome w/ neodymium motor
ICC™ with 10% (Tol) parts
Unified tab
Multi-OEM™ adaptor plates, grilles and mounting hardware
W-Style, Treated Cloth
Fiber reinforced paper w/ machined aluminum phase plug
Fatigue resistant polycotton linear spider w/ woven lead wire
StampCast™ with Flex-fit™
Ferrite magnet structure
N/A
ICC™ with 10% (Tol) parts
12 Ga. compression style
Grilles and mounting hardware
N/A
N/A
N/A
Die-cast aluminum with FlexFit™
Neodymium magnet structure
1.0” (25mm) horn design
ICC™ with 10% (Tol) parts
12 Ga. compression style
Mounting hardware
Ferrite magnet structure
1.5”(38mm) horn design
Ferrite magnet structure
1”(25mm) mylar balanced dome
Integrated high-pass crossover
Standard spade connector
Grilles and mounting hardware
18 Ga. Pigtail
Flush, surface and angle mounting hardware
Standard spade connector
Grilles and mounting hardware
SPE Foam
Vacuum formed PP
Fatigue resistant spider
Stamped steel
Tweeter
Sensitivity (1W/1M)
150 watts
Motor Structure
Frequency Response
75 watts
Frame Structure
Peak Power Handling (watts)
0.75”
Spider
RMS Power Handling (watts)
6”x9”
Cone Material
Tweeter Size
P1694
Surround Material
Speaker Size
[ SPEAKER SPECIFICATIONS [
Mylar balanced dome Nitrile Butadiene Rubber
Vacuum formed Polypropylene
Fatigue resistant spider
Stamped steel
Ferrite magnet structure
1/2”(13mm) Embedded Phase Coherent mylar balanced dome
Integrated high-pass crossover
1/2”(13mm) pole mounted mylar balanced dome
ROCKFORDFOSGATE.COM Don’t forget to use our Woofer Wiring Wizard to properly wire woofers to your amplifier or our Woofer Box Advisor for optimized enclosure bass performance. 73
2015 BUYER’S GUIDE
DIGITAL PROCESSORS SIGNAL CONVERTERS POWERED LOADED DIRECT FIT SPEAKERS
ACCESSORIES
VEHICLE INTEGRATION
DIGITAL PROCESSORS / LINE DRIVER PROPRIETARY 3SIXTY TECHNOLOGY
INTERACTIVE SIGNAL PROCESSOR
When you make a product purchase that bears the Rockford Fosgate name, you are receiving the technology, engineering and innovation that has taken over three decades to hone. Our constant desire to push the performance envelope has lead us to develop proprietary amplifier topologies and acoustic/electrical technologies that put a spin on the normal and make it Rockford.
®
3SIXTY.3
BLUETOOTH
The 3sixty.3 interactive signal processor is the perfect solution for those customers who want to add aftermarket equipment to their factory source unit, integrate their mobile devices, or have complete control over their audio signal. With features like Bluetooth streaming, selectable crossover types and a USB interface, the versatility is endless.
®
A2DP wireless audio streaming via the included dongle allows you to listen to audio from any BLUETOOTH enabled device.
BALANCED LINE DRIVER Rockford’s 2 channel Balanced Line Driver improves the performance of any aftermarket or factory radio. Designed to eliminate system noise and compatible with high level (speaker) inputs or low level (RCA) inputs.
RF LINK
Rockford’s proprietary RF Link is a bus-power component connection system enabling integration and control of all RF Link equipped products. The use of this system allows for the expansion of auxiliary controls and managed system turn on. RF-BLD
FREQUENCY NORMALIZATION OF AUDIO SIGNALS
U.S. Patent (7,778,718,B2)
UNIVERSAL PUNCH EQ Looking to add Rockford’s patented Punch EQ to any aftermarket audio system? Plus in need of features like high to low signal conversion, a line driver and auto turn-on.
Frequency normalization is achieved by characterizing the frequency response of the audio source based on a reference input signal. This reference input signal is used to establish a reference frequency response, which is stored in memory and used to select equalizer settings. The system restores missing spectral content by summing multiple input signals from the audio source. The system then normalizes the frequency response based on characterizations of the signal by utilizing equalizer settings from memory. RFPEQU
3SIXTY GRAPHIC USER INTERFACE (GUI)
INPUT CHANNEL CONFIGURATOR
HIGH TO LOW CONVERTER
OUTPUT CHANNEL CONFIGURATOR
What happens when your radio isn’t equipped with RCA inputs? Rockford offers high (speaker) to low (RCA) level converters in 2 or 4 channel versions.
RF-HLC4
CHANNEL SUMMING CONFIGURATOR
Input/Output
AUX Inputs
Input Voltage Output Voltage
Auto Turn-On
8 Speaker/RCA Balanced/Unbalanced
Stereo/Digital (SPDIF)
2V-24V
8V RMS Unbalanced/Balanced
RF-BLD
2 Speaker/RCA Balanced/Unbalanced
N/A
650mV-10.5V
RFPEQU
2 Speaker/RCA Balanced
N/A
RF-HLC4
4 Speaker/4 RCA
RF-HLC
2 Speaker/4 RCA
ADJUSTING INPUT GAIN 3SIXTY.3
3Sixty interactive graphic user interface allows for control of the crossover type, slope, high/low pass filter, the 248 band parametric eq, phase and time delay. 77
2015 BUYER’S GUIDE
Remote
Dimensions
6V DC Offset
Master or Sub Level/PEQ/ EQ Presets/Input
H 1.75” x W 5.125” x L 9.25”
11V RMS Unbalanced 22V RMS Balanced
6V DC Offset
N/A
H 1.32” x W 5.90” x L 4.09”
600mV-10V
10V RMS Unbalanced
6V DC Offset
PEQ
H 1.1” x W 3.15” x L 4.72”
N/A
Up To 10.5v
Up To 3v
N/A
N/A
H 1” x W 1.56” x L 3.5”
N/A
Up To 10.5v
Up To 3v
N/A
N/A
H 1” x W 3” x L 3.5”
BLUETOOTH / POWERED LOADED PUNCH POWERED LOADED
UNIVERSAL STREAMING TO RCA
The PUNCH PS-8 amplified subwoofer enclosure is designed for those tight spaces where most woofer enclosures won’t fit. With its low profile design and integration capabilities, this powered woofer system provides all the bass without taking up all the space, Mounting height is only 3.3” and comes with its own wiring kit!
The RFBTRCA universal Bluetooth™ adapter allows you to wirelessly stream media (music library, Pandora, Rhapsody, etc) from a Bluetooth™ enabled device directly to an RCA input and is powered by a direct 12v power connection.
RFBTRCA
UNIVERSAL STREAMING TO AUXILLIARY
RFBTAUX
If your vehicle didn’t come with built-in Bluetooth, now you can easily stream music from your smart phone, tablet, or laptop directly to the vehicle’s AUX input, using our RFBTAUX Universal Bluetooth Adapter. Cable Length
AUX Output
Input Signal
USB Charging Voltage
RFBTAUX
5 ft.
1/8” Stereo Jack
BLUETOOTH V3.0+EDR
5V/1A
RFBTRCA
3 ft.
1/8” Stereo Jack
BLUETOOTH V3.0+EDR
N/A
PS-8
AVAILABLE IN 10” AND 12” POWERED LOADED SOLUTIONS
Punch Powered Loaded enclosures are the quick and easy to install bass solution to upgrade your factory or aftermarket stereo system.
POWERALL MOBILE DEVICE CHARGER
The Rockford Fosgate RFC-350 is the personal charging device everyone needs. Featuring a rechargeable 9000mAh battery pack, this device charger has all the needed power for the person on the go who often finds themselves without access to a charger or wall outlet. Able to charge mobile devices via a 5V micro USB connection up to 2.1 Amps, this compact unit has all the juice you need to keep your devices running. And speaking of running, this handy unit can help you even when your vehicle no longer does because of a dead or drained battery. It stores enough power to jump start a vehicle with up to 350 amps of output capability to get you back on the road. Additionally, it also features an LED flashlight with 3 modes of operation: Solid ON, Strobe and S.O.S.
RFC-350
Input Voltage
Output Voltage
5v/1A (USB)
5v /2.1A (USB) 12v/350A
USB Charging Voltage
Dimensions
5V/1A
5.4”x3.3”x1”
RFC-350
P300-12
Integrated grille included.
Speaker Size
2015 BUYER’S GUIDE
Rated Power
Signal Input
Auto Turn-On
Remote
Dimensions
P300-10
10”
300 watts RMS/ 600 watts PEAK
Low-Level (RCA) or High-Level (Speaker)
12v REM, 6V DC Offset, Audio Signal
Included Punch Level Control (PLC)
H 13.3” x W 18.38” x L 9.37”
P300-12
12”
300 watts RMS/ 600 watts PEAK
Low-Level (RCA) or High-Level (Speaker)
12v REM, 6V DC Offset, Audio Signal
Included Punch Level Control (PLC)
H 14.96” x W 20.35” x L 11.5”
8"
150 watts RMS/ 300 watts Peak
Low-Level (RCA) or High-Level (Speaker)
12v REM, 6v DC Offset, Audio Signal
Included Punch LevelControl (PLC)
H 3.3" x W 13.9" x D 9.4"
PS-8 79
Three different automatic turn-on modes; REM (+12V), DC Offset, and Audio Signal.
T3 BMW DIRECT FIT SPEAKERS BMW DIRECT FIT SPEAKERS
FLEXIBLE FITMENT SYSTEM
INCLUDED Optional Mounting Bezel
Utilizing three unique OEM frame styles creates a TRUE direct fit solution for 2004 and newer BMW vehicles.
EXAMPLE 6-SERIES
This system upgrade requires using all three frame styles to be able to replace all the factory speakers.
FRAME STYLE ONE
FRAME STYLE TWO The included in-line crossover is equipped with OEM connectors and either a 0dB (reference) or +3dB amplitude increase to the tweeter.
T3-BMW1
FRAME STYLE THREE Multi-purpose connector; direct fit OEM connector or aftermarket spade terminal.
T3-BMW2
VISIT ROCKFORDFOSGATE.COM/PRODUCTS/FITMENTGUIDE FOR:
81
Speaker Size
Tweeter Size
RMS Power Handling
Peak Power Handling
Frequency Response
Sensitivity (1W/1M)
Sensitivity (2.83V/1M)
Mounting Depth
T3-BMW1
4”
1”
50 watts
100 watts
75Hz - 20kHz
90dB
93dB
1.14”
T3-BMW2
4”
1”
50 watts
100 watts
75Hz - 20kHz
90dB
93dB
1.25”
T3-BMW3
4”
1”
50 watts
100 watts
75Hz - 20kHz
90dB
93dB
1.66”
2015 BUYER’S GUIDE
Vehicle Fitment Guide
Installation Videos
Make Model Chassis
Year
T3-BMW3
The American Wire Gauge standard was developed to rationalize selecting wire for a particular purpose. In an electronic environment, wire size can have a significant impact on performance. Rockford Fosgate products are designed and engineered to perform at a superior level. It is only fitting that the accessories linking them together perform with the same expectation.
4 AWG
8 AWG
10 AWG
RFK1D
RFK4I
RFK8I
RFK1D - Dual Amp Kit RFK1 - Power Only Kit
RFK4D - Dual Amp Kit RFK4X - Complete Kit RFK4i - Power w/ Interconnect Kit RFK4 - Power Only Kit
RFK8X - Complete Kit RFK8i - Power w/ Interconnect Kit RFK8 - Power Only Kit
Dual Twisted Pair
Twisted Pair
Coupler
POWER KITS
RF ACCESSORIES EXCEEDING THE STANDARD
1/0 AWG
RFK10I
RFK10i - Power w/ Interconnect Kit RFK10 - Power Only Kit
INTERCONNECTS
THE AMERICAN WIRE GAUGE STANDARD The American Wire Gauge standard specifies the exact amount of copper needed to indicate a specific wire diameter or gauge. Rockford Fosgate accessories are all designed and engineered in accordance with the AWG specification.
RFIT-20
RFI-20
RFIS
• Available 3ft - 20ft Length • Y-Adapters
• Couplers
Battery Clamps
Fuses
Terminals
Battery Post Adapters
Fuse Holders
ANATOMY OF WIRE The construction of wire is broken out into three elements, strands, clusters and bundles. Varying these combinations will directly change the wire gauge and significantly effect the flexibility of the wire.
RFDB1
RFT1
RFDGM
RFFANL
• ANL Style 500-100A • MAXI Style 100-50A • AGU Style 60-30A
• Set Screw - 1/0 AWG & 4 AWG • Crimp - 1/0 AWG, 4AWG & 8 AWG • Barrier Spades - 4 AWG & 8 AWG
RFDGM - GM Battery Post Adapter RFDGML - GM Battery Post Adapter for Double Stacked Terminals
1/0 AWG
4 AWG
8 AWG
Speaker Wire
RFFANL - Inline ANL or MAXI Fuse Holder RFFAGU - Inline AGU Fuse Holder RFFMAXI - Inline MAXI Fuse Holder RFFDAGU - Fused AGU Distribution Block RFD1 - 1/0 AWG Distribution Block RFD4 - 4 AWG Distribution Block
RFW4R
WIRE SIZE IMPACTS SYSTEM PERFORMANCE The smaller the wire gauge (copper content) the greater the resistance which results in a loss in power to your amplifier(s) and speaker(s), thus creating a poor performing audio system!
RFW1R-51
RFW4B
• Red or Black • 100ft Spool
Hybrid
Electrolytic
RFWP12
• 12 AWG, 16 AWG, 18 AWG • 250/1000 ft Spool or Packaged
• Red or Black • 250ft Spool Deadskin
Powerall
RFC10HB
ROCKFORDFOSGATE.COM Don’t forget to use our Amp Wire Calculator to optimize output with properly sized wire. 83
2015 BUYER’S GUIDE
RFC10HB - 10 Farad Hybrid Digital Capacitor RFC2D - 2 Farad Hybrid Digital Capacitor
RFC1
RFC1D - 1 Farad Digital Capacitor RFC1 - 1 Farad Capacitor
RFDS
RFDS - Sound Damping Material 20’ square feet
RFC350
POWERALL RFC-350 - Portable Charger/Car Jumper Cables
FOR ADDITIONAL INFORMATION ON ACCESSORIES, PLEASE VISIT ROCKFORDFOSGATE.COM
CAPACITORS / DEADSKIN
• Red or Black • 51ft Spool
RFW8B
POWER WIRE
RFFU30
RFDB1 - 1/0 AWG +/Battery Clamp
DISTRIBUTION
• Available 3ft - 20ft Length • Y-Adapters
AMPLIFIERS SUBWOOFERS SPEAKERS SOURCE UNITS
AMPLIFIERS SUBWOOFERS SPEAKERS SOURCE UNITS
SOURCE UNITS Rockford’s PMX series of source units and remotes are fully tested against UV radiation degradation as well as tested to IPX water intrusion standards. We also fully test the units for ever changing environmental conditions such as temperature extremes, as well as vibration testing to make sure they can take a bump and keep performing like a Rockord product should.
SOURCE UNITS
Rockford’s element ready product line takes into account the effects of the environment and takes measures to ensure lasting performance.
Alternate
UV Inhibitor Materials – Centrex and ASA plastic materials are used for their UV radiation resistance and components are tested in accordance with ASTM D4329 testing and certification procedures.
Corrosion Protection (Speakers) – Components are tested for salt spray corrosion resistance and conform to ASTM B117 certification.
Thermal Shock Tested – Products are tested for extreme temperature operation as well as severe fluctuations in ambient temperature. Components are taken to both low and high temperature extremes and then tested to ensure operational capabilities.
Corrosion Protection (Electronics) – Two part epoxy coated PCB boards prevent corrosion of critical components due to exposure in moisture rich environments.
Stainless Hardware – Stainless hardware is used due to its natural resistance to corrosion and rusting. This ensures that electrical connections will not degrade over time due to exposure to the elements.
Vibration – Knowing our equipment will not be sitting still, we subject it to full vibration and shock testing to ensure that it will take abuse and keep performing to our stringent standards.
SUBWOOFERS/SPEAKERS Rockford knows that when you shop for speakers for your boat, UTV or motorcycle, you are looking for something that is not only going to sound amazing but stand up to the elements. We specify high grade UV resistant materials for our speaker housings and grilles and make sure that they meet ASTM testing standards. We also subject them to salt spray (fog) testing to make sure that exposure to the environment will not cause issues with corrosion, both from a hardware or electrical connection standpoint.
SUBWOOFERS/SPEAKERS
2015 BUYER’S GUIDE
Water Tested – IPX5 and IPX6 Ratings allow for the components to be directly sprayed with water without water incursion.
AMPLIFIERS
87
Dust – We make sure that displays and motor structures are sealed up tight so they look as clear as possible and perform day in and day out no matter how many times you hit the trails.
AMPLIFIERS Our Moto-marine amplifiers have not only the capabilities you expect a Rockford amp to have, but we have designed them to stand up to the environmental conditions you are likely to subject them to. With corrosion resistant stainless steel hardware and two-part epoxy coated circuit boards, these units are designed with you in mind. Whether on the lake, on the road or in the back woods these amplifiers are ready for an adventure.
UNPRECEDENTED POWER AND CONTROL
12
dB/OCT
CROSSOVER SLOPE
YEAR
OHMS
YEAR
2 1 2/1 LIMITED WARRANTY
FREE* EXTENDED WARRANTY
IMPEDANCE STABILITY
HISTORY OF PERFORMANCE
dB/OCT
12
CROSSOVER SLOPE
YEAR
OHMS
YEAR
1 1 4/2 LIMITED WARRANTY
FREE* EXTENDED WARRANTY
IMPEDANCE STABILITY
THE PERFECT FIRST STEP
LIMITED WARRANTY
OHMS
AMPLIFIERS AMPLIFIERS
YEAR
dB/OCT
12 1 4/2
CROSSOVER SLOPE
IMPEDANCE STABILITY
*WITH QUALIFYING ROCKFORD FOSGATE INSTALLATION KIT PURCHASE
SAME GREAT PUNCH AMPLIFIERS IN AN ELEMENT READY PACKAGE Punch is a name that has been synonymous with car audio for over 35 years. The mobile audio enthusiast in most cases is well versed in the quality and history of the Punch family of products. When we redesigned the mobile amplifier line in 2013 we knew that this new breed of Punch products would far surpass anything we had built previously. By integrating new circuit designs and developing our C.L.E.A.N. setup technology our engineers have created an amplifier family with capabilities not seen before. With the expansion of our Moto/Marine category this year, we wanted to offer that same amplifier offering, but in an
WHEN SIZE, POWER AND THE ELEMENTS ARE A CONCERN THESE AMPLIFIERS HAVE YOU COVERED Knowing your life isn’t restricted to just the highways and byways, Rockford Fosgate introduces their new series of Element Ready small chassis Power amplifiers. Building on the successful launch of the Mobile audio version of these amplifiers last year and seeing how many of our customers were also using them in their motorcycles, UTVs and boat systems, the Rockford Engineers wanted to create a version that was geared more toward a life in the elements.
MODELS SHOWN | TM500X1br, TM400X2ad
91
2015 BUYER’S GUIDE
Our new Element Ready series of Power amplifiers have all the same benefits and features of their Mobile counterparts, but we’ve also added additional protective components knowing these are not likely to be safe in the trunk of your car. With features like a brushed aluminum chassis with UV inhibitors added to the finish to a Marine grade two-part epoxy coating on the circuit boards, these small chassis powerhouses will let you continue enjoying your tunes while hitting the trails or cruising the lake with friends. MODELS SHOWN | PM1000X1bd, PM400X4, PM300X2, PM1000X5
Element Ready chassis. This new breed of Punch amplifier has all the amazing features as the mobile version but also now incorporates some of the necessary elements to help it withstand the off-road and on the water conditions. Featuring a brushed aluminum finish with UV inhibitors, a two-part epoxy coated circuit board and marine grade stainless steel hardware, these amplifiers are designed to give you all the performance you expect with the peace of mind that they will stand the test of time.
PRIMED TO HIT THE ROAD, TRAILS OR LAKE AND DELIVER THE TUNES Incorporating many of the technology elements that Rockford is known for, our Prime series of Element Ready amplifiers are an ideal choice if you are trying to build a system on a budget. With our high efficiency circuit design, these amplifiers are ideal for vehicles with limited electrical systems. They can easily exceed their power ratings giving you every watt you deserve and then some.
Built with a powder coated cast aluminum heat sink with integrated UV inhibitors and two part epoxy coated circuit boards, these amplifiers have been fully tested for all kinds of environmental conditions. Along with incorporating features such as variable crossovers and our famous Punch EQ circuit further completes the package making the Prime amplifiers a perfect choice for your system.
TH E G UT S OF AN AMPLIFIER
Organizing the combination of parts that make up the guts of an amplifier tremendously impacts its performance capabilities. A change in topology type matched with a variation of power supply components deliver a higher power output and enhanced audio quality. Rockford’s proprietary amplifier topologies and electrical technologies in our amplifier lineup will drive your system to new heights.
HEAT SINK MOSFETS
CONFORMAL COATED CIRCUIT BOARD
MARINE GRADE STAINLESS STEEL TERMINALS
93
2015 BUYER’S GUIDE
RCA
Heat Sink - This heavy outer shell protects the parts inside by transferring away the heat made reproducing an audio signal (music).
MOSFETs - A type of transistor used to amplify audio signal (music). You’ll see more of these guys lined up as wattage demands increase.
Conformal Coated Circuit Board Sometimes referred to as the PCB, is used to connect this-to-that through tiny lines of copper across multiple layers of pathways.
Power Supply - A.K.A. the transformer, as the name suggest it takes the incoming voltage and converts it to a useable voltage for speakers.
Marine Grade Nickel Plated Terminals These are the connection points for the speakers or subwoofers and the power source (battery) for the amplifier.
RCA - These are the connection points for the audio signal (music) coming from the audio source (radio). RCA connectors are most commonly used.
BESt
GOOD
MATERIAL HIErARCHY
MODELS SHOWN | M1200-1D, M400-4D, M600X5
POWER SUPPLY
500WATTS
400WATTS
750WATTS 1200WATTS
400WATTS 4.3”
6.8”
Extruded Aluminum w/ UV Inhibitors
Die-Cast Aluminum w/DTM™ and UV Inhibitors
Molex; Marine Grade Nickel Plated Set-Screw or Pigtail
Marine Grade Nickel Plated Set-Screw
8.3”
Balanced Differential; High-Level Capable with Auto Turn -On
1.6”
Balanced Differential; High-Level Capable
2”
TO-220 MOSFETs w/MEHSA™
TO-220 Bipolar Transistors 9.1”
Ferrite Core Coated/Booted Transformer • Our small footprint design makes these an ideal choice when space is a concern such as on a motorcycle or UTV. • Active heat management and forced air cooling ensures these amplifiers will deliver the power all day long.
4 Layer 2oz. Copper Circuit Board w/2-Part Epoxy Coating *TM400X4ad MODEL SHOWN
300WATTS 500WATTS 1000WATTS
300WATTS 400WATTS 500WATTS
400WATTS 600WATTS
600WATTS
• Designed with efficiency in mind, the Element Ready Prime amplifier family produces high output power without excessively taxing your electrical system. • With a powder coated cast aluminum heat sink, epoxy coated circuit boards and stainless steel hardware these amplifiers are ready to hit the trails or the lake any time.
Ferrite Core Transformer 2 Layer 2oz. Copper Circuit Board w/2-Part Epoxy Coating *M750-1D MODEL SHOWN
400WATTS 600WATTS
1000WATTS 6.8” 7.8”
Die-Cast Aluminum w/DTM™ and UV Inhibitors
Die-Cast Aluminum w/DTM™ and UV Inhibitors
Marine Grade Nickel Plated C-Clamp compression
Marine Grade Nickel Plated Set-Screw 2.4”
Balanced Differential; High-Level Capable with Auto Turn-On TO-220 MOSFETs w/MEHSA™ Ferrite Core Coated/Booted Transformer 4 Layer 2oz. Copper Circuit Board w/2-Part Epoxy Coating *PM1000X1bd MODEL SHOWN
13.3”
2”
Balanced Differential
11.1”
TO-220 MOSFETs Ferrite CoreTransformer
• Using a marine grade two part epoxy coating on the circuit boards, we ensure that these amplifiers will continue to function without concern of corrosion or rust buildup. • Marine grade stainless steel hardware is used for all electrical connections making sure that they remain corrosion free so your music will sound good no matter what environment your in.
• Our ultra-efficient 4-channel amplifier design uses the latest full range Class D technology to provide crisp clear sounds without taxing the electrical system. • Amplifiers are optimized for multi-channel systems layouts from simple to complex and are stable to 2 ohms per channel.
2 Layer 2oz. Copper Circuit Board w/2-Part Epoxy Coating *M600-4D MODEL SHOWN
96
1 ohm mono rated
>50dB
H 2.4” x W 7.8” x L 9.9” (Mini chassis)
TRANS•ana
4 layer 2 oz. copper circuit board
12 dB/oct - variable High or Low Pass and All Pass
2 ohm stereo / 4 ohm mono rated
>105dB
>50dB
H 2.4” x W 7.8” x L 9.9” (Mini chassis)
150mV - 12V
>105dB
>50dB
H 2.4” x W 7.8” x L 9.9” (Mini chassis)
<1.0%
150mV - 12V
>105dB
>50dB
H 2.4” x W 7.8” x L 9.9” (Mini chassis)
High level capable with auto turn-on balanced differential RCA inputs
20Hz - 20kHz
<1.0%
150mV - 12V
>105dB
>50dB
H 2.4” x W 7.8” x L 9.9” (Mini chassis)
High level capable with auto turn-on balanced differential RCA inputs and RCA pass thru
75x4 + 200x1 @ 4 ohms 125x4 + 400x1 @ 2 ohms N/A + 500x1 @ 1 ohm
20Hz - 20kHz
<1.0%
150mV - 12V
>105dB
>50dB
H 2.4” x W 7.8” x L 9.9” (Mini chassis)
TRANS•ana & Class bd
PM300X1
200x1 @ 4 ohms 300x1 @ 2 ohms
20Hz - 20kHz
<1.0%
150mV - 12V
>105dB
N/A
H 2.4” x W 7.8” x L 9.9” (Mini chassis)
TRANS•ana
PM500X1bd
150x1 @ 4 ohms 300x1 @ 2 ohms 500x1 @ 1 ohm
20Hz - 250Hz
<1.0%
150mV - 12V
>100dB
N/A
H 2.4” x W 7.8” x L 9.9” (Mini chassis)
Class bd
PM1000X1bd
250x1 @ 4 ohms 500x1 @ 2 ohms 1000x1 @ 1 ohm
20Hz - 250Hz
<1.0%
150mV - 12V
>100dB
N/A
H 2.4” x W 7.8” x L 9.9” (Mini chassis)
M400-4D
75x4 @ 4 ohms 100x4 @ 2 ohms 200x2 @ 4 ohms bridged
20Hz - 20kHz
<0.1%
150mV - 4V
>90dB
>50dB
H 2.0” x W 6.8” x L 9.1”
M600-4D
100x4 @ 4 ohms 150x4 @ 2 ohms 300x2 @ 4 ohms bridged
20Hz - 20kHz
<0.1%
150mV - 4V
>90dB
>50dB
H 2.0” x W 6.8” x L 11.1”
50x4 + 200x1 @ 4 ohms 75x4 + 300x1 @ 2 ohms 150x2 + N/A @ 4 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 12V
>100dB
>50dB
250x1 @ 4 ohms 500x1 @ 2 ohms 750x1 @ 1 ohm
20Hz - 250Hz
<1.0%
150mV - 4V
>100dB
M750-1D
400x1 @ 4 ohms 800x1 @ 2 ohms 1200x1 @ 1 ohm
20Hz - 250Hz
<1.0%
150mV - 4V
>100dB
M1200-1D
150mV - 12V
>110dB
>60dB
TM400X4ad
100x4 @ 4 ohms 100x4 @ 2 ohms 200x2 @ 4 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 12V
>110dB
>60dB
H 1.6” x W 4.3” x L8.3” (Compact chassis)
TM500X1br
175x1 @ 4 ohms 300x1 @ 2 ohms 500x1 @ 1 ohm
20Hz - 20kHz
<1.0%
150mV - 12V
>110dB
N/A
PM300X2
100x2 @ 4 ohms 150x2 @ 2 ohms 300x1 @ 4 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 12V
>105dB
PM400X2
125x2 @ 4 ohms 200x2 @ 2 ohms 400x1 @ 4 ohms bridged
20Hz - 20kHz
<1.0%
150mV - 12V
PM500X2
150x2 @ 4 ohms 250x2 @ 2 ohms 500x1 @ 4 ohms bridged
20Hz - 20kHz
<1.0%
PM400X4
50x4 @ 4 ohms 100x4 @ 2 ohms 200x2 @ 4 ohms bridged
20Hz - 20kHz
PM600X4
75 x 4 @ 4 ohms 150 x 4 @ 2 ohms 300 x 2 @ 4-Ohm Bridged
PM1000x5
M600X5
12 dB/oct - variable High or Low Pass and All Pass
NOMAD circuit • Reverse Polarity • Short Circuit • Thermal • Low Impedance • Under/Over Voltage
Dual fan forced induction cooling
Focused mass die-cast heatsink / DTM™- Dynamic Thermal Management / MEHSA™- Maximum Efficiency HeatSink Application
Additional Features
Protection
12 dB/oct - variable Low Pass
<1.0%
Speaker Terminals
Impedance Stability
4 layer 2 oz. copper circuit board
20Hz - 20kHz
Power Terminals
Variable Crossover
Class br
200x2 @ 4 ohms 200x2 @ 2 ohms 400x1 @ 4 ohms bridged
RCA Inputs
Circuit Board
H 1.6” x W 4.3” x L8.3” (Compact chassis)
TM400X2ad
Heatsink Design
Topology
NOMAD circuit • Reverse Polarity • Short Circuit • Thermal • Low Impedance • Under/Over Voltage
Channel Separation
2 ohm stereo / 4 ohm mono rated
S/N Ratio
12 dB/oct - variable High or Low Pass and All Pass
Input Sensitivity
4 layer 2 oz. copper circuit board
THD+N @ Rated Power
Class ad w/ Constant Power
Frequency Response
H 1.6” x W 4.3” x L7” (Compact chassis)
Rated Power
Dimensions
[ AMPLIFIER SPECIFICATIONS [
High level capable with auto turn-on balanced differential RCA inputs
8 Ga. Quick Connect terminal
16 Ga. 4-pin Molex connector
Punch EQ variable from 0dB to +18dB @ 45Hz and/or 0dB to +14dB @ 12.5KHz with optional Punch Level Control(PLC2)
High level capable with auto turn-on balanced differential RCA inputs and RCA pass thru
2 ohm stereo / 1 ohm mono rated
High level capable with auto turn-on balanced differential RCA inputs
2 ohm mono rated
High level capable with auto turn-on balanced differential RCA inputs and RCA pass thru
12 dB/oct - variable Low Pass
1 ohm mono rated
4 Ga. c-clamp compression connector
8 Ga. c-clamp compression connector
Punch EQ variable from 0dB to +18dB @ 45Hz and/or 0dB to +14dB @ 12.5KHz with optional Punch Level Control(PLC2)
Full Range Class d
4 layer 2 oz. copper circuit board
12 dB/oct - variable High or Low Pass and All Pass
2 ohm stereo / 4 ohm mono rated
• Short Circuit • Thermal
Focused mass die-cast heatsink
RCA input and RCA pass thru
4 Ga. set-screw connector
10 Ga. set-screw connector
Punch EQ variable from 0dB to +18dB @ 45Hz
H 2.0” x W 6.8” x L 13.2”
Class ab & Class d
Single layer 2 oz. copper circuit board
12 dB/oct - variable High or Low Pass and All Pass
2 ohm stereo / 4 ohm mono rated(Front/Rear) and 2 ohm mono rated(Sub)
• Short Circuit • Thermal
Focused mass die-cast heatsink
RCA input or speaker level pigtailed Molex connector input
4 Ga. set-screw connector
10 Ga. set-screw connector
Punch EQ selectable from 0dB/+6dB/+12dB @ 45Hz(Front/Rear) and Variable from 0dB to +12dB @ 45Hz(Sub)
N/A
H 2.0” x W 6.8” x L 9.1”
Class d
4 layer 2 oz. copper circuit board
12 dB/oct - variable Low Pass 12 dB/oct - variable infrasonic
1 ohm mono rated
• Short Circuit • Thermal
Focused mass die-cast heatsink
RCA input and RCA pass thru
4 Ga. set-screw connector
N/A
H 2.0” x W 6.8” x L 11.1”
10 Ga. set-screw connector
Punch EQ variable from 0dB to +18dB @ 45Hz and included Punch Level Control(PLC)
Don’t forget to use our Woofer Wiring Wizard to properly wire woofers to your amplifier or our Woofer Box Advisor for optimized enclosure bass performance. 2015 BUYER’S GUIDE
Punch EQ variable from 0dB to +18dB @ 45Hz with optional Punch Level Control(PLC2)
Punch EQ variable from 0dB to +18dB @ 45Hz with optional Punch Level Control(PLC2)
ROCKFORDFOSGATE.COM
97
10 Ga. nickel plated Quick Connect
HISTORY OF PERFORMANCE
YEAR
WATTS
300 ” 1 2 24
UP TO RMS POWER HANDLING
LIMITED WARRANTY
M M
VOICE COIL
XMAX PEAK TO PEAK
THE PERFECT FIRST STEP
SUBWOOFERS
SUBWOOFERS
YEAR
WATTS
200 ” 1 2 14 LIMITED WARRANTY
M M
UP TO RMS POWER HANDLING
VOICE COIL
XMAX PEAK TO PEAK
TURN YOUR BOAT INTO A “BOOMER” WITH THESE PUNCH ELEMENT READY WOOFERS
WHETHER OFF-ROAD OR ON THE WATER, PRIME ELEMENT READY WOOFERS HAVE YOUR BOTTOM LINE COVERED
Music without the low end is like eating a PB & J without the J. It’s just not the same and doesn’t feel complete. If you enjoy the full, rich sound of your audio system in your car, then why would you accept less in your boat or UTV system? This is where the Punch Family of Moto/Marine subwoofers come in. If you’ve had or heard our mobile line of Punch subs then you know that they have the capabilities of laying down the bass line and shaking the rust loose from any ride.
Always looking to offer our customers choices, we introduced our Prime series of Element Ready woofers. These woofers are built using many of the same technologies as our Punch woofers but with the customer who may not be looking the Punch level sound in mind. If you want the Rockford experience without breaking the bank then these woofers will deliver.
without again. These versatile woofers are designed to work in sealed, ported and infinite baffle applications and are built to withstand the environment. Using UV resistant materials in the cone, surround and basket assemblies ensure that they will stand up under the summer sun and our sealed motor structure with stainless steel hardware prevent any moisture intrusion or corrosion from occurring making sure the bass hits hard every time. We even offer them in a Sport or Luxury grill version to better fit the aesthetics of any boat or UTV design.
101
2015 BUYER’S GUIDE
S P ORT GRILLE
MODELS SHOWN | PM212S4X, PM212S4B, PM210S4
LUXURY GRILLE
With our Element Ready versions you are now able to take that bass with you on the lake or on the trail and never go
OPTIONAL COLOR
MODELS SHOWN | RM110D4B, RM112D4, RM18D4
Using ASA injection molded plastics for the baskets and grills, polypropylene cones and SantopreneTM surrounds all with integrated UV inhibitors ensures that these woofers will not break down over time due to exposure to the elements. Available in a variety of sizes and voice coil configurations, you’re sure to find one that will fit the application you need.
a n ato m y
SINGLE 4Ω
Mineral Filled Polypropylene Cone with UV inhibitors
High resistance to environmental conditions.
OF A SUBWOOFER
250-300
WATTS
Increased stiffness reduces distortion.
RMS POWER RANGE
Tall Profile, Santoprene™ w/ VAST™ Injection Molded Polypropylene w/ UV Inhibitors
Variations in the anatomy of a subwoofer dramatically changes its performance characteristics. An increase in voicecoil size coupled with a stronger cone material yields a higher power handling and increased output. By combining quality materials with Rockford’s proprietary acoustic technologies, our subwoofer lineup is sure to meet your system’s demands.
Single Nomex Blend w/ Multipoint Stitched Lead Wire 2” 4-Layer High Temp. KaptonTM w/ NomexTM collar 100% UV Stable Centrex Injection Molded Plastic Shielded Ferrite Magnet Structure
SURROUND
*PM212S4 MODEL SHOWN
UV Stable Centrex Injection Molded Parts
BASKET
CONE
High Rigidity. Outstanding UV and weather resistance.
SPIDER VOICE COIL MAGNET
DUAL 2Ω DUAL 4Ω
UV/ Salt Fog Resistant SantopreneTM Surround Ideal For changing environmental conditions.
MATERIAL HIErARCHY
BESt
Basket - Also referred to as the frame or chassis, this is the skeletal system of the speaker. Here to keep everything in its place.
150-200
WATTS
Long Life Span.
RMS POWER RANGE
UV and Salt/Fog Resistant, Santoprene™ w/ VAST™
Spider - Second part of the speakers suspension, connects the cone and voice coil to the basket and controls the travel of the cone assembly.
Injection Molded Carbon Fiber Filled Polypropylene w/ UV Inhibitors Single Aramid Fiber w/ Multipoint Stitched Lead Wire
GOOD
103
2015 BUYER’S GUIDE
Spider - Second part of the speakers suspension, connects the cone and voice coil to the basket and controls the travel of the cone assembly.
Cone - A.K.A. the diaphragm, this is the voice of the speaker. Shape and material dramatically change tonality.
Voice Coil - The brains of the operation, directing the force from the magnet to push or pull based on the applied electrical signal.
Magnet - The heart of speaker, creating the force to push and pull cone assembly. Size, material, and design may differ, depending on performance goals.
1.5/2.0” 4-Layer High Temp. Aluminum w/ NomexTM collar 100% UV Stable ASA Injection Molded Plastic Moisture, Tear and Fatigue Resistant Aramid Fiber Spider High strength. Maintains flexibility w/ changing temperatures.
Ferrite Magnet Structure *RM112D4 MODEL SHOWN
0.154
0.75
1.25 cu. Ft. Port: (1) 4" x 8.52" Infinite Baffle Compatible
PM212S4/ PM212S4B/ PM212S4X
12"
Single 4 Ω
12
87 db
300
600
11.25"
6.58"
0.258
1
1.5 cu. Ft. Port: (1)3" x 5.74" Infinite Baffle Compatible
8"
Dual 2 Ω or 4 Ω
7
85 dB
150
400
9.13"
4.4"
0.06
0.75
1.4 cu ft. Port: (1) 3”x8”
RM110D2/ RM110D2B/ RM110D4/ RM110D4B
10"
Dual 2 Ω or 4 Ω
7
89 dB
200
500
11.25"
5.1"
0.150
1.02
1.79 cu ft. Port: (1) 4”x9.3”
RM112D2/ RM112D2B/ RM112D4/ RM112D4B
12"
Dual 2 Ω or 4 Ω
7
89 dB
200
500
9.13"
4.3"
0.101
0.59
1.40 cu ft. Port: (1) 4”x13”
RM18D2/ RM18D2B/ RM18D4/ RM18D4B
Tall Profile, Santoprene with VAST
Injection Molded Polypropylene
Injection Molded Polypropylene
2” 4-layer high temp, aluminum voice coil with Kapton former and spun-laced Nomex insulating reinforcement collar
Tear & fatigue resistant Nomex blend spider with multipoint stitched lead wire technique
Centrex
Shielded ferrite magnet structure with extended vented pole and bumped backplate
Proprietary gold plated compression terminal. 8 Ga.
Water draining Centrex trim ring with integrated stainless steel grill or luxury grill option
UV and Salt Fog Resistant Co-Molded Santoprene Surround
Injection Molded Polypropylene
Injection Molded Carbon Fiber Filled Polypropylene Cone Body with UV Inhibitors
1.5" 4-layer high temp. copper voice coil with aluminum former
Tear & fatigue resistant poly-cotton spider with multipoint stitched lead wire technique and spider cooling vents
100% UV Stable ASA Injection Molded Plastic
Ferrite magnet structure with extended pole piece, vented aluminum voice coil former and bumped backplate
Proprietary Corrosion Resistant Spring Loaded Push Terminals. 12 Ga.
Water draining ASA trim ring with integrated grill
2" 4-layer high temp. aluminum voice coil with spun-laced Nomex™ insulating reinforcement collar
ROCKFORDFOSGATE.COM Don’t forget to use our Woofer Wiring Wizard to properly wire woofers to your amplifier or our Woofer Box Advisor for optimized enclosure bass performance. 105
2015 BUYER’S GUIDE
Trim Ring
Sealed Enclosure (cu. ft.)
5.54"
Terminal Connectors
Speaker Displacement (cu. ft.)
9.13"
Motor Structure
Mounting Depth
500
Frame Structure
Mounting Diameter
250
Spider
Peak Power Handling (watts)
86 dB
Voice Coil
RMS Power Handling (watts)
10
Cone Material
Sensitivity
Single 4 Ω
Dustcap Material
Xmax (mm)
10"
Surround Material
Nominal Impedance
PM210S4/ PM210S4B/ PM210S4X
Ported Enclosure
Speaker Size
[ SUBWOOFER SPECIFICATIONS [
150 1
WATTS
HISTORY OF PERFORMANCE
UP TO RMS POWER HANDLING
YEAR
LIMITED WARRANTY
40 - 22 Hz
kHz
FREQUENCY RESPONSE
THE PERFECT FIRST STEP
SPEAKERS
SPEAKERS
YEAR
WATTS
75 1
UP TO RMS POWER HANDLING
LIMITED WARRANTY
49 - 20 Hz
kHz
FREQUENCY RESPONSE
BE THE ENVY OF THE CAMPSITE OR THE SANDBAR WITH OUR PUNCH ELEMENT READY SPEAKERS If you want to really crank up the party then our wake tower speaker enclosures are just the thing you need. Available with our new horn loaded or coaxially mounted component design, these cans will make you the envy of the lake or campsite.
109
2015 BUYER’S GUIDE
OPTIONAL COLOR
OPTIONAL COLOR
RM0652
DOME TWEETER
OPTIONAL COLOR
MODELS SHOWN | RM1652B, RM0652
S PORT GRILLE
HORN TWEETER
OPTIONAL COLOR
S PORT GRILLE
LUXURY GRILLE
S PORT GRILLE
MODELS SHOWN | PM282W, M262-WAKE, PM282HW, PM282B, PM262, PM282X
Our new Element Ready Prime series of speakers shows that you don’t have to blow your yearly budget just to get good sound out of your audio system especially when it has to live in an environment such as your boat, UTV or even your motorcycle. We’ve designed these speakers with efficiency and output in mind. Available with two different tweeter sizes and power handlings, these speakers can belt out the tunes without needing an amplifier the size of a nuclear power plant.
RM1652
If you’re someone who truly enjoys their music one way and that way is all the way up then you need to look at the Punch family of Moto/Marine speaker and wake tower cans. These Element Ready speakers are designed to hold up under the harshest conditions and still belt out your music just the way you like. Using many of the same construction materials found on our Marine woofers you can rest assured they will keep on rocking regardless of a little mud or water getting on them.
BIG THINGS TRULY DO COME IN SMALL PACKAGES.
OPTIONAL COLOR
Using UV inhibitor based materials and corrosion resistant hardware these speakers are designed with the person who lives for the outdoors in mind. So if you’re looking for a speaker that is built with the quality and to the standards the Rockford expects of all its products and will stand up to your active lifestyle then these are the speakers for you.
f r a m e wo r k
2WAY 8.0”
HORN WAKE
OF A SPEAKER
Modifications to the framework of a speaker significantly impact its sonic signature. Combining various materials will strengthen, add volume and resonate the music to a desired sound. By intertwining superior speaker designs with Rockford’s proprietary acoustic technologies in our speaker lineup we are sure to bring your music to life.
Coaxially mounted horn loaded tweeter w/ Neodymium motor structure High Quality 6dB High pass crossovers using Metalized Polyester Film Capacitors UV & Salt-Fog resistant TPE (Thermo Plastic Elastomer) surround w/ VAST™ Injection molded mineral filled polypropylene with UV inhibitors
SURROUND
CONE
TWEETER
• Our high output horn tweeter and midrange speaker assembly with their Neodymium motor structures are designed for high volume applications. • Enclosures are constructed of high density poly-ethylene, have a paint and clear coat finish with integrated UV inhibitors and are available in black or white colors (Same as PM282W wake speakers).
High Density Poly-ethylene Enclosure with UV Inhibitors Hi power Neodymium magnet structure *PM282HW MODEL SHOWN
BASKET CROSSOVEr 2WAY 8.0”
MAGNET
WAKE
MATERIAL HIErARCHY
BESt
GOOD
111
2015 BUYER’S GUIDE
Tweeter - Composed of the same parts as an speaker, surround, cone, voice coil, basket and magnet. Just on a smaller scale.
Cone - A.K.A the diaphragm, this is the voice of the speaker. Shape and material dramatically change tonality.
Crossover - Works like a switch board, directing the audio signal through caps, filters and switches to the appropriate speaker.
Basket - Also referred to as the frame or chassis, this is the skeletal system of the speaker. Here to keep everything in their place.
UV & Salt-Fog resistant TPE (ThermoPlastic Elastomer) surround w/ VAST™
Surround - Works in harmony with the spider, attached to the cone to maintain the centering of the voice coil in the magnetic gap.
Magnet - The heart of speaker, creating the force to push and pull cone assembly. Size, material, and design may differ, depending on performance goals.
High Density Poly-ethylene Enclosure with UV Inhibitors
Bridge mounted component grade coated aluminum alloy tweeter Integrated 6/12 dB per octave sealed crossover.
Injection molded mineral filled polypro pylene with UV inhibitors
• Our 8 inch full range cans come loaded with our PM282 speakers and produce crisp and clear full range sound for those not only in the boat but out as well. • Our 8 inch cans ship with a surface mount bracket included and an optional tubular clamp is also available for wake tower mounting. • Mounting assemblies feature security Torx hardware, safety lanyards and 359 degree rotation capabilities for directional adjustments.
Hi power Ferrite magnet structure *PM282W MODEL SHOWN
2WAY 6.0”
2WAY 6.5”
WAKE
Bridge mounted component grade coated aluminum alloy tweeter
Grill Integrated Proprietary LCP Dome Tweeter
Integrated 6/12 dB per octave sealed crossover.
High Quality 6dB High pass crossovers using Metalized Polyester Film Capacitors
UV & Salt-Fog resistant TPE (ThermoPlastic Elastomer) surround w/ VAST™
UV and Salt Fog Resistant Co-Molded Santoprene Surround w/ VAST™
Injection molded mineral filled polypropylene with UV inhibitors High Density Poly-ethylene enclosure with UV Inhibitors Hi power Ferrite magnet structure
Injection molded Carbon Fiber filled polypropylene with UV inhibitors • Our 6 inch full range wake cans use our PM262 full range speaker and are available in black or white finishes. • The 6 inch can assemblies are shipped with both a surface mount and tubular clamp assembly for versatile mounting options.
• Our Marine RM1 full-range speakers are perfect for anyone looking to add some FANATIC sound to their vessel or side-by-side. • With our specially designed volcano dome LCP tweeter the RM1 speakers produce crystal clear highs even when rocketing across the lake or racing up the sand dunes.
*PM262-WAKE MODEL SHOWN
100% UV stable ASA injection molded plastic Linear, high excursion matched motor magnetics and suspension design *RM1652 MODEL SHOWN
2WAY 6.5”
2WAY 6.0” 8.0”
Grill Integrated LCP Dome Tweeter
Bridge mounted component grade coated aluminum alloy tweeter
High Quality 6dB High pass crossovers using Metalized Polyester Film Capacitors
Integrated 6/12 dB per octave sealed crossover.
UV and Salt Fog Resistant Co-Molded Santoprene Surround w/ VAST™
UV & Salt-Fog resistant TPE (ThermoPlastic Elastomer) surround w/ VAST™ Injection molded mineral filled polypropylene with UV inhibitors
Injection molded Carbon Fiber filled polypropylene with UV inhibitors
100% UV stable Centrex™ injection molded plastic
100% UV stable ASA injection molded plastic
Linear, high excursion matched motor magnetics and suspension design *PM262 MODEL SHOWN
113
2015 BUYER’S GUIDE
• The PM2 full range speakers incorporate a 1 inch aluminum alloy component tweeter, coaxially mounted over the midrange, to produce crisp and clear full range sound for you to enjoy while relaxing on the water. • To compliment your vehicle’s interior the PM2 full range speakers are available in both a black and white sport grill and a white luxury grill option.
• Our 2-way component system with a coaxially integrated tweeter is built using stringent marine grade weather proofing technologies to ensure the speakers will perform under the harshest conditions. • Using high grade internal crossover components ensures that both the tweeter and midrange produce high quality sound and play the frequencies they are supposed to..
Linear, high excursion matched motor magnetics and suspension design *RM0652 MODEL SHOWN
91 dB
2.8"
PM282/ PM282B/ PM282X
8"
1.0"
100 watts
200 watts
48Hz - 22kHz
90 dB
93 dB
3.4"
RM0652/ RM0652B
6.5"
.5"
50 watts
100 watts
52Hz - 20kHZ
88 dB
91 dB
2.5"
RM1652/ RM1652B
6.5"
1.0"
75 watts
150 watts
49Hz - 20kHz
89 dB
92dB
2.5"
Terminal Connectors
Mounting Depth
88 dB
Crossover
Sensitivity (2.83V/1M)
53Hz - 22kHz
UV & Salt-Fog resistant TPE (Thermo-Plastic Elastomer) Santoprene surround
Injection molded mineral filled polypropylene cone body with UV inhibitors
Moisture, tear and fatigue resistant aramid fiber spider
UV stable Centrex™ 814 injection molded plastic parts
Linear, high excursion matched motor magnetics and suspension design
1” (25mm) bridge mounted component grade coated aluminum alloy tweeter
Integrated 6/12 dB per octave sealed crossover.
Corrosion resistant gold plated polarized input terminals
UV and Salt Fog Resistant Santoprene Surround
Injection molded mineral filled polypropylene cone body with UV inhibitors
Moisture, Tear and Fatigue Resistant Aramid Fiber Spider
100% UV Stable ASA Injection Molded Plastic Parts
Linear, high excursion matched motor magnetics and suspension design
Grill Integrated 1" Proprietary LCP Dome Tweeter
High Quality 6dB High pass crossovers using Metalized Polyester Film Capacitors
Proprietary Corrossion Resistant Spring Loaded Push Terminals
Tweeter
Sensitivity (1W/1M)
150 watts
Motor Structure
Frequency Response
75 watts
Frame Structure
Peak Power Handling (watts)
1.0"
Spider
RMS Power Handling (watts)
6"
Cone Material
Tweeter Size
PM262/ PM262B/ PM262X
Surround Material
Speaker Size
[ SPEAKER SPECIFICATIONS [
Grill Integrated 0.5” LCP Dome Tweeter
Dimensions (HxWxD)
WAKE CANS
Peak Power Handling (watts)
M262-WAKE/ M262B-WAKE
RMS Power Handling (watts)
PM282HW/ PM282HW-B HORN WAKE CANS
Nominal Impedance
PM282W/ PM282W-B WAKE CANS
Speaker Size
[ WAKE SPEAKER SPECIFICATIONS [
8" woofer/ 1" Aluminum Tweeter
4Ω
100 watts
200 watts
14.2" x 9.1" x 10.09"
8" woofer/ 1" Horn Tweeter
4Ω
150 watts
300 watts
14.2" x 9.1" x 10.09"
6" woofer/ 1" Aluminum Tweeter
4Ω
75 watts
150 watts
10.96" x 7.03" x 11.26"
ROCKFORDFOSGATE.COM Don’t forget to use our Woofer Wiring Wizard to properly wire woofers to your amplifier or our Woofer Box Advisor for optimized enclosure bass performance. 115
2015 BUYER’S GUIDE
SOURCE UNITS
DESIGNED AND ENGINEERED WITH A PURPOSE AND YOU IN MIND Rockford has long recognized a person’s desire to easily connect with their music. With that in mind we set out to create a purpose built line of Moto/ Marine source units equipped with all the latest technology and features. In looking at the market, we saw that many of the source units being used in Moto/Marine applications were simply repurposed mobile audio units and know that they were not originally designed to be in a boat, UTV or motorcycle environment. This is why Rockford decided to take the ground up approach in designing this new source unit line.
MODELS SHOWN | PMX-1R, PMX-5, PMX-2, PMX-8DH, PMX-0R
119
2015 BUYER’S GUIDE
From a hardware standpoint we talked to both industry professionals and the consumers who use these products to determine what worked and more importantly what didn’t. From this we designed several units with varying capabilities to suit the needs of our customers from a simple streaming receiver to a hide-away control box with remote display. We also designed the software and menu system from the ground up making the menus easy to use and access. The last thing you want is to be shooting down the trail fumbling through a complex menu system. If you are looking for a high quality source unit with a purpose specific design to be the heart of your system then look no further.
DNA
Full Function Wired Display Head 5"
5” Ultrabright Color TFT Display, IPX6 Certified Faceplate, Optical Wet Bonded N/A
OF A SOURCE UNIT
N/A N/A
A source unit is the heart of any good sound system and flexibility, features and ease of operation of are often at the top of the list of any customer when it comes time to decide on which one to use. Rockford has designed their new Marine grade source units from the ground up with user friendly menu designs, input and output flexibility as well as multi-zone/ multi-source controllability.
N/A Thru-hole surface mount, Rear bolt thru mounting plate/ .625” mounting depth *PMX-8DH MODEL SHOWN
EQUALIZATION
ZONE/SOURCE CONTROL
DISPLAY
5"
• This full function display head is specifically designed for use with our PMX-8BB and allows total access to all its functions and features. • Its large 5 inch display makes it easy to see what’s on as well as navigate the custom menus.
MEMORY
INPUT SIGNAL
Hide-Away Digital Media Receiver
MOUNTING SYSTEM DEPTH
5"
N/A Bluetooth, SiriusXM, Pandora, iPod iPhone, Dual USB, Aux, A/V, AM/FM/WB
MATERIAL HIErARCHY
BESt
5"
GOOD
121
2015 BUYER’S GUIDE
DISPLAY - The display is how you receive information from the unit and see the settings for the internal menus. It can also display signal and song information if available.
ZONE/ SOURCE CONTROL - A unit with multi-Zone/ Source control provides for more flexibility in system designs by creating different zones of the system and allowing different sources to be played in them.
INPUT SIGNAL - The number and types of input signals a source unit can accept help determine its flexibility in a system design and help you determine if it will fit your needs.
EQUALIZATION - The equalizer allows you to tune the system to your taste via a multi-band EQ or our own proprietary Punch EQ circuit.
MEMORY - The internal circuit that retains all settings and stations when power is no longer applied to the unit.
MOUNTING SYSTEM - The system by which the unit mounts into the vehicle and depth of the chassis helps to determine where you can mount the unit.
EEprom memory with zero current draw on power down Nitrile Rubber 4-Zone/ 2-Source 7 Band Equalization + PEQ2 Surface mount/ Hideaway Black Box w/2.2” height PMX-8BB MODEL SHOWN
• When joined with the PMX-8DH this hide-away black box unit is a feature rich command center for your entire audio system. • Whether installing a small system or a complex multi zone system, this unit has the features and functionality you’re looking for.
5"
2.7” Full Color TFT Display IPX6 Certified Faceplate, Optical Wet Bonded
Digital Media Receiver With Oversized Display
Ultra Compact Digital Media Receiver 5"
Bluetooth, SiriusXM, Pandora, iPod iPhone, Dual USB, Aux, A/V, AM/FM/WB
Bluetooth, USB, Aux N/A
EEprom memory with zero current draw on power down
2-Zone/ 1-Source
2-Zone/ 2-Source
N/A
7 Band Equalization + PEQ2
Thru-hole surface mount, Rear bolt thru mounting plate, Gauge style C-Clamp/ 3” mounting depth
Thru-hole surface mount, Rear bolt thru mounting plate/ 7.25” mounting depth
*PMX-0 MODEL SHOWN
*PMX-5 MODEL SHOWN
• With its oversized display and single DIN chassis this multimedia receiver is designed for ease of use with a built from the ground up GUI and menu system. • If a true multi zone/ multi source capable source unit is what you’re looking for then this unit has you covered.
Compact Digital Media Receiver 5"
• This compact streaming audio receiver is ideal if you typically play music via your Bluetooth enabled device. • Its small size and mounting footprint make it ideal when real estate is tight.
Full Function Wired Remote
2.7” Full Color TFT Display IPX6 Certified Faceplate, Optical Wet Bonded
5"
2.7” Full Color TFT Display IPX6 Certified Faceplate, Optical Wet Bonded
Bluetooth, Pandora, iPod/iPhone, USB, Aux, AM/FM/WB
N/A
EEprom memory with zero current draw on power down
N/A
2-Zone/ 1-Source
Multi-Zone/Source control via source unit
7 Band Equalization + PEQ2
N/A
Thru-hole surface mount, Rear bolt thru mounting plate, Gauge style C-Clamp/ 3” mounting depth
Thru-hole surface mount, Rear bolt thru mounting plate, Gauge style C-Clamp/ 3” mounting depth *PMX-1R MODEL SHOWN
*PMX-2 MODEL SHOWN
• This compact receiver is perfect when you need the functionality of a multimedia unit without the size typically associated with them. • Its multiple mounting options allow for versatility wherever you need to install it.
123
N/A
2015 BUYER’S GUIDE
• This full function remote control is designed to give you access to all the same controls and settings you get on the primary receiver units. • Up to three remote units can be connected to and are designed to work with the PMX-8BB, PMX-5 and PMX-2 units.
Wired Remote 5"
N/A N/A N/A N/A N/A Thru-hole surface mount, Rear bolt thru mounting plate/ 7.25” mounting depth
*PMX-0R MODEL SHOWN
• When a compact remote unit is needed for simple control of your multimedia receiver units, the PMX-0R is ideal. • Up to three remote units can be connected to and are designed to work with the PMX-8BB, PMX-5 and PMX-2 units.
125
2015 BUYER’S GUIDE
SOURCE UNIT SPECIFICATIONS
Description
Features
Dimensions
Full Function Wired Display Head w/ 5” Hi-Res Color Display
Illuminated Waterproof Rotary Encoder Volume Control, Front Panel Sub Control, Front Panel Illumination Control, Ultra Slim Design, Tactile Inverted and Extraverted Buttons for Easy Identification, IPX6 Certification, Back Lit LED Button Illumination
H 4.63” x W 8.00”
Hide-away box Digital Media Receiver for PMX-8DH 50 watts x 4
Global AM/FM/WB Tuner, SiriusXM Ready, Full iOS/Andriod, Made for iPod, Dual USB Input w/ Video Playback, BLUETOOTH avrcp 1.5, 2-Source Zone Control, 4-Zone Volume Control, 6 Channel F/R/S 4V Zone 1&2 Preouts, 2 Channel Zone 3&4 4V Preouts, 7-Band Graphic Equalizer, Punch EQ, A/V Input, Video Output, CAN Ready, Remote Control Ready, EEPROM NonVolatile Memory,Wired Illumination Control, Steering Wheel Control Ready
H 2.20” x W 8.24” x D 6.86”
Digital Media Receiver w/ 2.7” Full-color Display 50 watts x 4
Global AM/FM/WB Tuner, SiriusXM Ready, Full iOS/Andriod, Made for iPod, USB Input, BLUETOOTH avrcp 1.4, 2-Source Zone Control, 6 Channel F/R/S 2V Zone 1 Preouts, 2 Channel Zone 2V Preouts, 7-Band Graphic Equalizer, Punch EQ, CAN Ready, Remote Control Ready, EEPROM Non-Volatile Memory, Front Panel Sub Control, Front Panel & Wired Illumination Control, Illuminated Waterproof Rotary Encoder Volume Control, IPX6 Front Panel Certification, Back Lit LED Button Illumination, Steering Wheel Control Ready
DIN size chassis w/ 1.75 DIN face H 3.50” x W 8.00”
Compact Digital Media Receiver w/ 2.7” Full-color Display 50 watts x 4
Global AM/FM/WB Tuner, Full iOS/Andriod, Made for iPod, USB Input, BLUETOOTH avrcp 1.4, 4 Channel (Front and selectable Rear/Sub Channel) 2V Preouts, 7-Band Graphic Equalizer, Punch EQ, CAN Ready, Remote Control Ready, EEPROM NonVolatile Memory, Front Panel Sub Control, Front Panel & Wired Illumination Control, Waterproof Rotary Encoder Volume Control, IPX6 Front Panel Certification, Back Lit LED Button Illumination
H 3.95” x W 4.33”
Ultra Compact Digital Media Receiver
AUX Input, BLUETOOTH avrcp 1.4, 4 Channel (Front and selectable Rear/Sub Channel) 2V Preouts, Front Panel Sub Control, Front Panel Illumination Control, Waterproof Rotary Encoder Volume Control, IPX6 Front Panel Certification, Back Lit LED Button Illumination
H 2.25” x W 4.00”
PMX-1R
Full Function Wired Remote w/ 2.7” Full-color Display for PMX-8BB, PMX-5, PMX-2
Multi Zone Control (PMX-5 & PMX8), Front Panel Sub Control, Waterproof Rotary Encoder Volume Control, Front Panel Illumination Control, IPX6 Front Panel Certification, Back Lit LED Button Illumination
H 3.95” x W 4.33”
PMX-0R
Wired Remote for PMX-8BB, PMX-5, PMX-2
Front Panel Sub Control, Waterproof Rotary Encoder Volume Control, Front Panel Illumination Control, IPX6 Front Panel Certification, Back lit LED Button Illumination
H 2.25” x W 4.00”
PMX-8DH
PMX-8BB
PMX-5
PMX-2
PMX-0
COMPLETE AUDIO KITS INSTALLATION KITS SPEAKER ADAPTERS
140 2-CH SYSTEM
[ R1-HD2-9813 ]
RF ACCESSORIES RFKHD9813
(1) 140 Watt 2-Channel Amplifier
MOUNTING PLATE AND WIRING HARNESS
COMPLETE AUDIO KIT
• The RFKHD9813 amplifier installation kit works with both the Power small chassis and PUNCH PBR series amplifiers. • The aluminum mounting plate adds additional thermal mass to the amplifier’s heat sink to improve performance and power output. • This complete installation kit includes an amplifier mounting plate and hardware, pre-terminated power and ground wires and pre-terminated speaker wires.
160 4-CH SYSTEM
[ R1-HD4-9813 ]
(1) 160 Watt 4-Channel Amplifier
COMPLETE AUDIO KIT
With 4 speakers, mounting plate and wiring harness
*TM400X4ad Shown
*PBR300X4 Shown
FITS HARLEY - DAVIDSON® MODELS Ultra Classic® Electa Glide®
129
2015 BUYER’S GUIDE
Street Glide®
1998 Tri Glide®
2013 Road Glide®
Road Glide Ultra®
AMPLIFIER/SPEAKER INSTALLATION KIT
With 2 speakers, mounting plate and wiring harness.
3
3 RECOMENDED 4-CH SYSTEM
Speaker Adapter Rings
(1) 300 Watt 4-Channel Amplifier PBR300X4
• Our PMSA Haley Davidson speaker adapter rings allow you to easily upgrade your factory speaker. • Designed for a direct fit application they perfectly align with the factory speaker mounting holes. • They allow you to install a variety of Rockford Power, Punch and Prime speaker from 6.0 to 6.75 inches.
(4) Speakers P1675
(1) Amplifier Mounting Plate With Wiring Kit RFKHD9813
(4) Direct Fit Front Speaker Adapters PMSA675
RECOMENDED 2-CH SYSTEM (1) 300 Watt 2-Channel Amplifier PBR300X2
(2) Speakers
PMSA675
INTEGRATE
RFKHD9813
PMSA675
P MSA6 5
FITMENT GUIDE
P1675
(1) Amplifier Mounting Plate With Wiring Kit RFKHD9813 (2) Direct Fit Front Speaker Adapters
MOUNTING KIT
SUGGESTED AUDIO SYSTEMS
RF ACCESSORIES
T16
P16
T165
P165
N/A
RECOMENDED 4-CH SYSTEM (1) 400 Watt 4-Channel Amplifier T400X4ad or TM400X4ad
(4) Speakers
P M S A6 7 5
T1675
FITMENT GUIDE
(1) Amplifier Mounting Plate With Wiring Kit RFKHD9813
(4) Direct Fit Front Speaker Adapters PMSA675
T1650*
P1650
T1675*
P1675
R165X3
*T1650 and T1675 Will not fit the Road Glide ® models
MOUNTING KIT
INTEGRATE
131
2015 BUYER’S GUIDE
FITS HARLEY - DAVIDSON® MODELS Ultra Classic® Electa Glide® RFKHD9813
PMSA675
Street Glide®
1998 Tri Glide®
2013 Road Glide®
Road Glide Ultra®
