Transcript
Model: LPTR4-series
Lowell Pull & Turn Rack – 19"D
(up to 250 lbs. load)
Description: The LPTR4 with 19” depth is a knockdown rack made for built-in installations, such as inside cabinetry, to provide convenient slide-out access to rackmounted equipment. The removable base can be mounted flush or recessed up to 1.75 inches to allow room for equipment protrusions. The rack secures to its base with front and rear screws. When equipment is mounted and wired, secure the assembly with screws through the front security panel. To service equipment, remove the security panel and slide the rack fully forward, then push the button (in center of base front) to release the lock and rotate the rack until it locks securely at 60 or 90 degrees. Note: When installing rack inside cabinetry, allow sufficient space at sides for rack rotation. Recessed installations may not allow enough room to rotate rack 90 degrees. Features: • Rack with two side stiffeners. • Base includes integral turntable with push button release and four bottom rails to support the slide-out rack. • Accommodates a load up to 250 lbs. • Six (11-ga. steel) corner-post rails tapped 10-32 • Six cable lacing bars • Front security panel (perforated) • Made in the U.S.A. with 100% certified U.S. steel • Black powder epoxy finish • Ships in 2 cartons for efficiency: CARTON ONE includes base with integral turntable, 2 rear corner-post rails, 3 cable lacing bars. CARTON TWO contains rack bottom, 4 corner-post rails, 2 side stiffeners, front security panel, 3 lacing bars. A & E Specifications: The rack shall be Lowell Model ________. It shall be formed from certified U.S. steel and have a smooth black powder epoxy finish. It shall measure 19.13"W x 19.22"D and have 19" useable depth. Panel space shall be _______. The rack shall include a base with two bottom rails and an integral turntable to allow the rack to slide forward, rotate and lock at 60 or 90 degrees. It shall also include six cable lacing bars and be capable of supporting a load up to 250 lbs.
Six rear cable lacing bars. Height of front rails varies by model. Height of rear rails is 7U on all models.
Ships unassembled in two cartons.
Rack slides forward from base, rotates and locks at 60 or 90 degrees.
Optional steel top with black finish (LPTR-TC).
Optional: (order separately) • Steel Top (LPTR-TC): black steel top or shelf. To Service an Installed Rack: 1. Remove the security panel (2 screws). If panel is not used, lock the rack by replacing the screws without the panel. 2. Pull the rack forward to clear the opening. 3. Push the button in the center front of the base to release the turntable and rotate the rack 60 or 90 degrees (right or left). Note: rotate the rack 90 degrees before tying cables to rear lacing panels to ensure adequate length at maximum turn radius.
Model No.
Description Rack Units* Overall D Useable D Panel Space Overall H Overall W
LPTR4-1019 LPTR4-1219 LPTR4-1419 LPTR4-1619 LPTR4-2119 LPTR4-2419 LPTR4-2819 LPTR4-3019 LPTR-TC
Lowell Pull & Turn Rack – 4 slides Lowell Pull & Turn Rack – 4 slides Lowell Pull & Turn Rack – 4 slides Lowell Pull & Turn Rack – 4 slides Lowell Pull & Turn Rack – 4 slides Lowell Pull & Turn Rack – 4 slides Lowell Pull & Turn Rack – 4 slides Lowell Pull & Turn Rack – 4 slides Steel Top Cover
10 12 14 16 21 24 28 30
19.22" 19.22" 19.22" 19.22" 19.22" 19.22" 19.22" 19.22"
19.00" 19.00" 19.00" 19.00" 19.00" 19.00" 19.00" 19.00"
17.50" 21.00" 24.50" 28.00" 36.75" 42.00" 49.00" 52.50"
20.08" 23.58" 27.08" 30.58" 39.33" 44.58" 51.58" 55.08"
*One rack unit = 1.75"
Spec. No. 1036 (rev. 09.16.13) pg. 1 of 2
©2013 Lowell Manufacturing Company, 100 Integram Dr., Pacific MO 63069. Phone–800.325.9660 Fax—636.257.6606. Lowell makes every effort to provide accurate information while reserving the right to change specifications and/or improve manufacturing methods without notification. (lowellmfg.com)
19.13" 19.13" 19.13" 19.13" 19.13" 19.13" 19.13" 19.13"
Assemble the rack and base, then dock the rack into position
Rack turned 90 degrees for cabling tie-off.
Rack and base assembled with corner post rails and lacing panels.
Six lacing bars. Perform wire tie off when rack is rotated 90 degrees to ensure adequate slack.
Height of front rails varies by model. Height of rear rails is 7U on all models.
When equipment is mounted and wired, secure rack with two screws through front security panel.
Dock rack to base and secure with front/rear screws. Then secure in position with 2 screws through front security panel.
Rack slid out from base
Rack turned 60 degrees
Rack turned 90 degrees
Base installation
1.41 1.41
16.00 16.00
18.13 18.13 12.13 12.13
6.0 6.0 11.0 11.0 3.0 3.0
0.261 hole 0.261 holeif if mounting tot stud mounting 0.281 holes 0.281 h for mounting mo
13.97 13.97
19.22 19.22
19.
13
19.13 19.13
.22
19
19.
00
All measurements are inches.
Spec. No. 1036 (rev. 09.16.13) pg. 2 of 2
©2013 Lowell Manufacturing Company, 100 Integram Dr., Pacific MO 63069. Phone–800.325.9660 Fax—636.257.6606. Lowell makes every effort to provide accurate information while reserving the right to change specifications and/or improve manufacturing methods without notification. (lowellmfg.com)
