Transcript
Spec No. 1566 | Rev. 07.30.15 | pg. 1/3 Heard Everywhere Since 1947
Model No.
LPTR2-1019 • 10U x 19.22"D x 19.13"W • Load capacity 125 lbs.
Pull out rack is designed to allow easier access to equipment stored in cabinetry. The removable base can be mounted flush or recessed up to 1.75" (to allow room for equipment protrusions). The rack secures to its base with front and rear screws.
Features • Base with integral turntable has a push button release and two bottom rails to support the slide-out rack. • Corner post rails are 11 gauge steel tapped 10-32 • Six cable lacing bars • Front security panel (perforated) attaches with screws • 1U vented panel • Black powder epoxy finish • Made in the U.S.A. with 100% certified U.S. steel • EIA compliant • Ships unassembled in two cartons • Includes assembly and mounting hardware
A & E Specifications The rack for built-in applications shall be Lowell Model No. LPTR2-1019 which shall be certified U.S. steel with a smooth black powder epoxy finish. Overall measurements shall be 20.08"H x 19.13"W x 19.22"D with 10U panel space. The base shall feature two bottom rails and integral turntable to allow the rack to slide forward, rotate and lock at 60 or 90 degrees. The rack shall include six cable lacing bars, 1U vented panel, perforated security panel and side supports with obround openings. Load capacity shall be 125 lbs. The rack shall ship unassembled in two cartons. Installation Notes
• When installing, make sure to allow sufficient space at the sides for rotation. Note that some recessed installations may not have sufficient room to rotate a full 90 degrees.
• To ensure adequate cable length at the rack's maxi-
mum turn radius, rotate the rack fully before tying cables to rear lacing panels (see pg. 3).
To Service Equipment in an Installed Rack 1) Remove the security panel (attached with 2 screws). 2) Pull rack forward to clear the opening. 3) Push button on base front to release the turntable and rotate until it locks at 60 or 90 degrees (right or left) to work on equipment. Optional (order separately) • LPTR-TC: Steel top. Black finish.
• LPTR-NS: Zero space shelf for oversized (wide) equipment mounts to rack's side rails. 18.79"W x 16.38"D x 1.75"H. Bottom vents; side obrounds.
Lowell makes every effort to provide accurate information while reserving the right to change specifications and/or improve manufacturing methods without notification. ©2015 Lowell Manufacturing Company, 100 Integram Dr., Pacific MO 63069 | 800.325.9660 | www.lowellmfg.com
Spec No. 1566 | Rev. 07.30.15 | pg.2/3 Heard Everywhere Since 1947
Model No. Summary Model No.
LPTR2-1019 LPTR-TC LPTR-NS
Description
Racking Space
Pull & Turn Rack Optional steel top Optional zero space shelf
Technical Drawings
10U
Overall Depth
Useable Depth
19.22 in / 488 mm
Overall Height
19.00 in / 483 mm
20.08 in / 510 mm
(Model No. LPTR2-1019)
Overall Width
19.13 in / 486 mm
Measurements are inches.
19.125
16.75
17.50 18.312 CL TO CL
20.08
17.50 10U
17.812
19.34 FRT COVER TO REAR FLANGE
Lowell makes every effort to provide accurate information while reserving the right to change specifications and/or improve manufacturing methods without notification. ©2015 Lowell Manufacturing Company, 100 Integram Dr., Pacific MO 63069 | 800.325.9660 | www.lowellmfg.com
Spec No. 1566 | Rev. 07.30.15 | pg. 3/3 Heard Everywhere Since 1947
Installation Drawings (sample shown may differ from spec model) Base
Dock Rack to Base
Secure with front and rear screws.
1.41
16.00 18.13 12.13
6.0 11.0 3.0
Measurements are inches.
0.261 hole if mounting to stud 0.281 holes for mounting
13.97 19.22
19.13
Rack Pulled Out From Base
Rack Rotated 60 Degrees
Rack Rotated 90 Degrees
NOTE: To ensure adequate slack, perform wire tie off when rack is fully rotated.
Wire tie-off
Attach Front Security Panel
When equipment is mounted and wired, slide rack back into position and attach the front security panel with screws. (Note: use the screws to secure the rack even if the security panel is not used.)
Lowell makes every effort to provide accurate information while reserving the right to change specifications and/or improve manufacturing methods without notification. ©2015 Lowell Manufacturing Company, 100 Integram Dr., Pacific MO 63069 | 800.325.9660 | www.lowellmfg.com
