Lunenburg High School Performing Arts Center - Renkus

Transcript

Loudspeaker System Recommendation Lunenburg High School Performing Arts Center Prepared for: Norris Inc. Application Engineering Renkus-Heinz, Inc. 6/27/2014 Contents Recommendation ------------------------------------------------------------------------------------------------------------ 2-3 Equipment List ------------------------------------------------------------------------------------------------------------------ 4 Array Configuration ------------------------------------------------------------------------------------------------------------- 5 EASE mappings -------------------------------------------------------------------------------------------------------------- 6-7 Product Datasheets ----------------------------------------------------------------------------------------------- Following 8 Design Goals Renkus-Heinz has been asked to recommend a sound reinforcement system for the Lunenburg High School Performing Arts Center. Our design goals were to provide a highly versatile system for a high school PAC. The system was designed to be musical, with enough SPL to handle a broad range of program material. Natural sounding, intelligible speech was another large design consideration due to the wide range of use the room will see. Of course this performance must be delivered evenly to all seats in the house. Room Details The room is about 60 feet deep by about 106 feet wide with ceilings about 32 feet high. The stage extends another 21 feet back from the front wall of the room, and thrusts 3 feet inward from the front wall. The main floor sinks 3 feet below the actual floor level, then rises in the middle, and then seating extends upwards about 10 feet toward the back wall. Recommended Loudspeaker System The recommended loudspeaker system is a pair of IC16-R-II for the mains, complimented by 5 CFX42 lip fill speakers in the stage. Low frequency energy can be handled by 2 PN212-SUBR flown above the stage. Loudspeaker mounting location The IC16-R-II are mounted flush with the proscenium wall flanking the stage about 31 feet away from center of the room, 6 feet above the stage floor toed inward 10 degrees. The CFX42 speakers are all installed into the lip at the top of the stage starting directly on the center line, then spaced apart 16.33 feet between each box. Understanding EASE Mappings in Appendix The system has been designed with the aid of EASE, Enhanced Acoustic Simulator for Engineers, a product of the Ahnert-Feistel Media Group, GmbH, Berlin, Germany. EASE is the international standard for sound-system design and prediction and has been proven accurate in thousands of successful sound system installations world-wide. For more on EASE and sound system prediction, please see AFMG’s website: http://ease.afmg.eu/ “System Coverage” maps show system coverage averaged over two octaves, at the frequency range indicated, of the seating areas at ear height. The mapping is predicted Direct Sound Pressure Level in dB. No room effects are included. These maps do not represent how loud the system will get, but rather consistency of coverage. The “Maximum SPL, A-Weighted” map shows the approximate maximum level the system would reach as shown on an SPL meter set to read broad band, A-weighted, fast. Important Disclaimer: All simulations have been done with industry standard techniques and software using information supplied by others. They are believed to be accurate within normal tolerances for such simulations providing the data supplied was accurate. Renkus-Heinz makes no guarantee that the final system will perform as simulated. Renkus-Heinz guaran2 tees only that any Renkus-Heinz equipment will perform to its published specifications within normal industry tolerances. The above is a recommendation only and is not to be considered or represented as a design by RenkusHeinz. WARNING! Hanging loudspeakers is a serious undertaking that should be done only by qualified and experienced personnel. Check with an Architect or Structural Engineer to verify any building attachment points. Renkus-Heinz is not responsible for any non-Renkus-Heinz products or for any misuse of Renkus-Heinz products. Thank you for the opportunity of making this recommendation. 3 Appendix 1, Equipment List Item RH Part Number Qty. Main IC16-R-II 2 CFX42 5 PN212-SUBR 2 4 Appendix 2, Array configuration 5 Appendix 3, EASE Mappings System Coverage at low frequencies, 100-400 Hz. Average System Coverage at mid frequencies, 500-2000 Hz. average 6 System Coverage at high frequencies, 2,500-10,000 Hz. average System Coverage, maximum SPL A-weighted 7 End of Recommendation Product datasheets on following pages 8 Digitally Steerable Loudspeaker Array System Musical Sound For Imposing Spaces Iconyx arrays are the first solution to combine digital control and steering with exceptional audio fidelity. They integrate high-performance acoustical components, advanced audiophile-quality digital electronics and powerful software in practical, modular systems that virtually disappear in most applications. Hundreds of installations around the world have proven that Iconyx digitally steerable arrays enable both effective communication and expressive musical artistry, even in highly reverberant acoustical environments. Third generation Iconyx IC-R-II series arrays feature further refined signal processing algorithms and purpose-designed coaxial transducers with three HF dome tweeters and provide even more clarity, musicality and intelligibility. Configuration presets and many other user requested features add to their versatility and ease of use. Transparent Solutions • Houses of Worship: traditional & modern • Transportation terminals: train stations, airports, etc. • Stadiums & arenas: lobbies & fore courts • Convention centers, warehouses, etc. • Museums: lobbies, galleries, etc. • Performing arts centers: vocal/orchestral “lift,” lobbies, etc. • Any highly reverberant environment where enjoyable music and/or intelligible speech are as important as the architectural design MUSICAL • INTELLIGIBLE • PRACTICAL “Array Within An Array” Triple Tweeter Design Iconyx IC-R-II arrays use multichannel high-current digital amplifiers to power advanced, purpose-designed coaxial transducers, each one with its own triple tweeter high frequency array. The triple tweeter “array within an array” design reduces the distance between high frequency sources for greatly improved high frequency performance with consistent broad horizontal dispersion. RHAON Audio Operations Network RHAON brings a new level of control and flexibility to Iconyx installations. Straightforward network connections empower multi-channel digital audio distribution, user-controlled DSP, user-selectable presets and comprehensive remote system management and control – all using standard Ethernet hardware and cabling. Configuration Presets Iconyx IC-R-II series arrays can store up to 10 different setup configuration presets in their digital memory and easily recall them from either the amplifier control panel, the controlling computer or from a third party controller. Flexibility & Power Iconyx technology gives sound system designers the power to cover almost any audience area perfectly. Multiple sonic beams can be individually shaped and aimed from a single Iconyx array using the software-controlled DSP: up to 8 beams on an IC16-R-II. The acoustic center of the array can also be raised or lowered electronically, because all array elements are identical and equidistant. © 2011 Renkus-Heinz Inc. reserves the right to change any product specification without prior notification. IC16-R-II IC16/8-R-II • Proven Performance • Coaxial Transducers with Triple HF Tweeters in an “Array Within an Array” Design • Multiple Configuration Presets • Slim, Architecturally Pleasing Design musical & Natural Clearly Intelligible The graphic below shows that the tight beam control continues as the frequency increases. Natural Speech, Enjoyable Music Communication is about more than consonants – meaning is conveyed by the tone of voice as well as the text. We also believe that beautiful spaces deserve beautiful music. That’s why Iconyx IC-R-II arrays use an audiophile-quality multi-channel amplifier to drive purpose-designed coaxial transducers with triple HF tweeters. The three tweeters are aligned vertically and act as an “array within an array” to better control vertical directivity at higher frequencies. Coaxial transducer with triple tweeters developed specifically for Iconyx BeamWare display of an Iconyx array at 4 kHz illustrating the reduced grating offered by Iconyx IC-R-II series arrays with their improved algorithms and evenly spaced triple dome HF tweeters. Iconyx IC-R-II arrays are also capable of producing and controlling multiple acoustic beams. The vertical alignment maintains consistently broad horizontal dispersion, allowing each Iconyx array to cover a wider section of the audience. BeamWare display showing the multi-beam capabilities of Iconyx arrays Conventional Transducer Coaxial Transducer Coaxial transducers with triple tweeters provide more consistent horizontal coverage, broader HF beamwidth The digital steering used in Iconyx IC-R-II arrays produces an “umbrella” polar pattern: the steering works in all directions, not just along the lobe’s axis. This reduces the amount of energy bouncing off the side walls. The end result is more direct sound and less reflected energy; the classic recipe for superior intelligibility. The three tweeter “array within an array” design also produces a more coherent high frequency output with greatly reduced grating lobes. Notice the tight vertical control and minimal grating lobes in the graphic shown below. Compared to passive column arrays (left) Iconyx arrays (right) deliver an “Umbrella” of  sound Expandable Modular Systems BeamWare display of an Iconyx array at 2 kHz illustrating the reduced grating offered by Iconyx IC-R-II arrays with their improved algorithms and evenly spaced triple dome HF tweeters. Page 2 To suit different needs, Iconyx systems are available in four sizes: all are constructed from the basic eight-channel IC8-R-II module to simplify shipping and transportation. The modules are easily transported and quickly joined together in the field. A single module forms the IC8-R-II, two modules form the IC16-R-II, three the IC24-R-II and four the IC32-R-II. All bring high output, crisply articulated, naturally balanced sound to every listener. maximum control prEsets RHAON is the first practical system to combine individual loudspeaker control and supervision of self-powered loudspeaker systems with digital audio distribution. RHAON makes it easy to connect, control and monitor multiple Iconyx IC-R-II series arrays and a mixture of other Renkus-Heinz powered loudspeakers using standard Ethernet cabling and switches - all over a single Cat 5 cable. Powerful Algorithms, Intuitive Interface The software algorithms that shape and aim the output of an Iconyx array, control iand supervise it are complex, but the user interface is intuitively simple. Large, easy-to-understand windows guide users through the process of Connecting, Controlling and Supervising the system. Multiple Input Options Iconyx IC-R-II arrays equipped with RHAON offer a variety of input options. Dual analog inputs are standard along with a serial AES/EBU digital input and multi-channel digital audio via CobraNet. Priority override allows any input to be given override capabilities over other inputs. Selection is accomplished quickly and easily from a centrally located computer Connect Setup Window Advanced Digital Signal Processing A powerful DSP inside each Iconyx IC-R-II array on the network is controlled by RHAON. It provides eight bands of parametric EQ plus high and low frequency shelving filters, input level control, muting, up to 340 ms of delay, compression and beam steering.. Our BeamWare software, an integral part of RHAON, lets you model the audience area, then drag and drop beams until coverage is optimized. BeamWare then calculates a set of FIR (Finite Infinite Response) filters that control the array ‘s beams. At installation time, simply download the full set of FIR filters from your computer to the Iconyx IC-R-II series modules over the Ethernet network. The beams can be easily adjusted from your computer after the Iconyx array is installed. If the array was hung too low, simply raise the array’s acoustical center using software instead of re-hanging the array. Control Window Setup Window Multiple Presets, Easy Selection RHAON’s comprehensive network capabilities make it easy to add one-touch presets and Iconyx R-II series arrays can store up to 10 different configurations in the their DSP memory. For example, you might optimize one configuration for small events on the main audience area, and another for larger occasions with listeners in the balcony. Once the configurations are stored, it’s easy to switch from one to another. Up/Down buttons and a readout on the rear panel of the array allow an operator to scroll through the available presets. This function can also be performed remotely from the central control computer, by means of a remote control panel if a central computer is not being used or from third party controllers such as those made by Creatron. Beam Control & Preset Window Continuous Supervision RHAON tracks critical operating parameters such as signal clipping, amplifier output voltage and current and temperature with automatic alert functions. Whenever a failure occurs, the icon representing that loudspeaker will turn from green to red to alert you to the problem. The associated Supervisory window provides more details. RHAON is not pre-certified as a life-safety system, but it has been designed to meet the requirement of most local authorities. Redundant signal paths and programmable priority override functions are built in. Continual monitoring of each networked loudspeaker, with automatic operator alert and logging functions, help you make sure the system is available when it’s most urgently needed. Supervisory Window Page 3 Sensitivity: 1.0 V (for rated power output) IC16-R-II & IC16/8-R-II Specifications Freq. Range: 120 Hz to 18 kHz Max SPL: IC16-R-II: 99 dB peak,@ 100 Ft. (30.5 meters); IC16/8-R-II: 96 dB peak,@ 100 Ft. (30.5 meters); (3-octave bandwidth centered at 2 kHz) Horiz. Dispersion: 150° up to 3 kHz; 120° above 3 kHz 6 1/4" 15.6 cm 6 7/8" 17.5 cm 6 1/8" 15.5 cm Vert. Opening Angles: 20°, 25° and 30° Vert. Aiming Angle: IC16-R-II: adjustable from -30° to +30° IC16/8-R-II: adjustable from -10° to +10° Typical Throw: 135 Ft. (40 meters) Beam Control: Effective down to 400 Hz №. Transducers: 16 coaxial transducers, each having triple tweeters №. Amp. Channels: 16 in IC16-R-II; 8 in IC16/8-R-II Dimen. (W/mtg Hinges): 74 3/4” H x 6 1/8” W x 6 7/8 D (190 cm x 15.5 cm x 17.5 cm) Weight: IC16-R-II; 72 Lbs (32.7 Kg). IC16/8-R-II: 62 Lbs (28.1 Kg) Hanging Method: 2-point hinges or Metric M6 thread eye-bolts. Enclosure: Extruded Aluminum with perforated steel grille; Transducers: Coaxial with a 4” woofer and triple 1” tweeters, RH model SSL4-7; 25 W RMS, 50 W pgm 74 3/4" 190 cm 65 13/16" 167.2 cm Inputs: Analog Audio:2 inputs (primary & secondary), Phoenix 6-pin connectors (looping 3-in, 3-out) CobraNet: Dual RJ45 connectors (for CAT 5 cable) Fiber Optic input for primary CobraNet input available as an option. AES/EBU: Phoenix connector Power: IEC power connector Surge Protector available as an option Controls (Rear Mounted): Mute button, Up & Down Output Level buttons, 10 dB pad (on Analog 1 input) Push-To-Reset circuit breaker Preset Configuration Selector (10 configurations) Computer Controls: Gain, Mute, On/Standby, Input Selection; Compression, 8-Band Parametric EQ, Shelving & Rolloff Filters, Delay, Preset Configuration Selection Status Indicators: Power, Signal, Overdrive, Thermal, Mute, Input Pad, Preset Configuration Selection Readout Finish: White paint standard; optional finishes, black and custom color paint; weather resistant DSP/AMPLIFIER Type: 8-channel, Class D amplifier/DSP processor One used in IC16/8-R-II; two used in IC16-R-II Input Impedance: >20K Ohm balanced differential Max Input: +24 dBu (Pad in);+14 dBu @ 1V sensitivity (Pad out) Power Rating: 50 Watts RMS per channel Freq. Range: + 3, - 3 dB, 100 Hz to 20 kHz THD Distortion: < 0.05% typical Hum & Noise: <100 dB (A weighted) Power Required- Universal 90/260 V AC, 50/60 Hz for each Amp Module 24 VA Idle; 325 VA @ rated output 200 ma Idle; 2.7 Amps at RPO (@ 120 V) Note: All analog inputs and outputs comply with AES Standard 48-2005 on interconnecting, grounding and shielding. Renkus-Heinz, Inc., 19201 Cook Street, Foothill Ranch, CA 92610-3501, USA Tel: 949-588-9997 • [email protected] • www.renkus-heinz.com RH 739 December 2011 CF/CFX Series Commanding Performance, Compelling Value Soundthatmakesperformancesandaudiencestrulycomealive doesn’tcomeeasy.ButCF/CFXSeriesloudspeakersputthepower ofuniqueRenkus-HeinzdevelopmentslikeComplexConichornsto workforyou.Versatileenclosuredesigns,go-anywherehardware andruggedconstructionhelpsolveyoursoundreinforcementchallengeseasilyandquickly.Advancedoptionslikeintelligentonboard amplificationandRHAON—theRenkus-HeinzAudioOperations Network—helpyoubuildsophisticatedsoundsystemsthatareeasy touse. CFX42 Non-Powered Dual 4” + 1” HF 2-way Stairstep Loudspeakers EveryCF/CFXSeriesloudspeakerisengineeredbyRenkus-Heinzto unrivaledstandardsofqualityandinnovation.Beforewe’llshipthem, yourloudspeakershavetomeetourexactingrequirementsfor performancethatwillmakeyouproudanddurabilitythatwillkeep yousoundinggreat. Applications •Developedspecificallyforin-wallmountinginstairrisersand stagelips. •Idealformanysideandfrontfillapplications;mounts inconspicuouslyinwallsorceilings,underandoverbalconies,etc. •Foregroundmusicsystemsinshoppingmalls,retailstores, offices,Etc. • High Volume Output, Small Enclosure High Performance, High Output, In-Wall Design Outstanding,full-range300Hzto20kHzperformanceina spacesaving‘in-wall”design. TheCFX42wasdevelopedspecificallyforthemultitudeofapplicationsneedingfull-sizeperformancefromacompactloudspeakerthat couldbeeasilymountedinstairtreads,wallsandceilings. • Wide-Angle 150° by 60° Coverage Itfeaturesa1"highfrequencycompressiondriverwitha1"throat coupledtoadiffractionslotanddual4"woofers.Thediffractionslot eliminateshighfrequencybeamingandprovideswideanglecoverageoutto20kHzandbeyond.Thedualhigh-efficiency4"woofers produceastronglowend.Together,the1"HFdriveranddual4" woofersdeliverasurprisinglyhigh122dBpeakoutputlevelfrom 300Hzto20kHz. • 1" Extended Range Titanium HF Driver ThecompactCFX42mountseasilybetween16"studs(it'sonly14 3/8"wideby53/8"high)instairtreads,stagelips,wallsandceilings.Protectionagainstdamageisprovidedbyaheavygaugesteel grille. Anoptionalheavygaugemetalbackboxisavailableforapplications wherebuildingcodesrequireametalenclosureortheloudspeaker willbeinstalledinconcrete. Highfrequencydiffractionslotprovidessmooth150°by60° coverage. Providessmooth,lowdistortionhighfrequencyperformanceto 20kHzandbeyond. • Dual Heavy-Duty 4" Woofers Easilyhandle240Wattsofprogrampower. • Heavy 18 Gauge Metal Back Box Optional18gaugemetalbackboxis“concretepour”ready. • Built-in Crossover Eliminatesneedforaseparateelectroniccrossoverand bi-amplification. ©2011Renkus-HeinzInc.reservestherighttochangeanyproductspecificationwithoutpriornotification. TECHNICAL INFORMATION Sensitivity CFX42: 95dB(1W/1m) Power­­ 240Wattsprogramat16Ohms Connectors Screwterminals&looping4-pinNeutrik Speakonstyleconnectors Maximum­SPL: 122dBpeak Dispersion: 150°Hby60°V Finish: Blackorwhitepaint Freq.­Resp: 300Hzto20kHz Dimensions Enclosure: 53/8”"Hx165/8"Wx95/8"D (13.7cmx42.2cmx24.4cm) HF­Driver: 1"Titaniumdriver,modelSDA105-8; 15WRMS,30Wprogram Grille: 53/4”Hx17”Wx1/4”D 14.6cmx43.2cmx.64cm LF­Drivers:­ Dual4",modelSSL4-6;4"Woofers; 60WRMS,120Wprogrameach. Back­Box: 55/8”H,x167/8”Wx133/16”D (14.2cmx43cmx33.5cm) Enclosure:­­ Hardwoodwithperforatedmetalgrille Back­Box: 18ga.CRSw/blackpowdercoat. Weight 16.8Lbs(7.7Kg)net Note:AllanaloginputsandoutputscomplywithAESStandard48-2005oninterconnecting,groundingandshielding. DIMENSIONAL INFORMATION Amplifier 16 5/8” 14 3/8” 9 5/8” 5 3/8” 5 3/4” Grille 17” 1/4” Back Box 16 7/8” 16 7/8” 13 3/16” 5 5/8” 5 5/8” Renkus-Heinz,Inc.,19201CookStreet,FoothillRanch,CA92610-3501,USA Tel:+1949-588-9997•Fax:+1949-588-9514•[email protected]• www.renkus-heinz.com RH736September2011 PN/PNX Series Uncompromising Performance, Unequalled Versatility Self-powered PowerNet PN and non-powered PNX Series loudspeakers unite advanced technology and application-driven engineering to bring live sound closer to the ultimate reference point: reality. Cutting edge driver technology and unique innovations such as our Complex Conic horns deliver natural sounding music and intelligible speech. Advanced options like intelligent onboard amplification and RHAON - the RenkusHeinz Audio Operations Network - help you build sophisticated sound systems that are easy to use. Wherever audiences and operators demand superior performance and ease of use, PN/PNX loudspeakers are the choice for transparent, reference quality performance. PN112 PN212 Single & Dual 12” PowerNet Subwoofers PNX112 PNX212 Single & Dual 12” Externally-Powered Subwoofers ACTIVE • POWERED • NETWORKED MAXIMUM CONTROL • MAXIMUM CHOICE All PN and PNX series loudspeakers are handcrafted especially for you in our Foothill Ranch, California facility. Numerous custom options are available. Applications • Virtually any application where the visceral impact obtainable only from high power subwoofers is required. Permanent Installations • Ideal for live music and speech reinforcement, club/disco systems and high power distributed systems. • Churches, schools, performing art centers, night clubs, stadiums and arenas. Portable Applications • Ideal for live music and speech reinforcement, portable DJ systems and high output distributed systems. • Rental A/V, DJ systems, churches, schools, etc. PN-1/PN-1R PowerNet Amplifiers The PN-1, the heart of PowerNet performance, is a new kind of intelligent electronics system. It combines low feedback Class A/B amplification and comprehensive signal processing into a single compact unit. Crossovers and parametric EQ are integrated into the signal path. Loudspeaker specific processing senses when output levels are about to damage the system and limits them to safe levels. • Powerful Single and Dual 12-inch Subwoofers Provide high-impact sub-bass performance (128 dB peak SPL on the PNX112-SUB & 134 dB peak SPL on the PN212-SUB). • RHAON Renkus-Heinz Audio Operations Network Self-powered PN112-SUBR and PN212-SUBR models include RHAON for flexible digital signal distribution, loudspeaker manage ment & control. • PN112-SUB & PN212-SUB PowerNet Subwoofers The PN-1R adds RHAON, the Renkus-Heinz Audio Operations Network. RHAON empowers you with full control over digital audio distribution, loudspeaker specific DSP and remote control/ monitoring -- all using standard Ethernet hardware and cable. The PN-1R has dual analog inputs, dual CobraNet inputs and an AES3 serial input. The onboard DSP is easily configured using RHAON software; it includes eight bands of parametric EQ, high and low shelving filters, delay and input level control. Critical operating parameters such as signal clipping, amplifier output voltage and current, and temperature are continually monitored with automatic alert functions. Include the PN-1 Class A/B amplifier with loudspeaker specific signal processing and protection. • PNX112-SUB & PNX212-SUB Non-Powered Subwoofers Same high performance as the self-powered PN series subs only externally powered. Weather resistant models are available. • High Power, High Performance 12-inch woofers With long throw magnetic structures and dual channel air cooling. • Great Versatility All PN series subwoofers are available in either portable or fixed installation versions in a wide choice of finishes. If you need Ethernet-based audio operations networking, order the single 12” RHAON empowered PN112-SUBR or the dual 12” PN212-SUBR. © 2009 Renkus-Heinz Inc. reserves the right to change any product specification without prior notification. TECHNICAL INFORMATION Sensitivity PN112 & PN212: PN112R & PN212R: PNX112SUB: PNX212SUB: Max SPL PN112SUB & PN112SUBR: PNX112SUB: PN212SUB & PN212SUBR: PNX212SUB: Freq. Response: LF Drivers PN112SUB: Power – All PN Series: PNX112SUB: PNX212SUB: Connectors–PNX Series: 115 V AC or 230 V AC, 50/60 Hz 800 Watts program at 4 Ohms 1600 Watts program at 4 Ohms Screw terminals & looping Neutrik 4-pin SpeakOn style connectors Finish: Black, white or custom color paint Natural (unfinished), Weather Resistant Hardware Options: 16-point univ. mtg. hdw.; tripod socket PN Weather Resistant Kit Dimensions: PN112 Series: 20 1/2" H x 15 1/2" W x 22 1/2" D (52.1 cm x 39.4 cm x 57.2 cm) PN212 Series: 14 1/2" H x 32" W x 23 1/4" D (36.8 cm x 81.3 cm x 59.1 cm) Weight: PN112SUB & PN112SUBR: 82 Lbs (37.2 Kg) net PNX112-SUB: 72 Lbs (32.7 Kg) net PN212SUB & PN212SUBR: 113 Lbs (51.3 Kg) net PNX212SUB: 103 Lbs (45.7 Kg) net 1.4 V for RPO 1.0 V for RPO 96 dB (1W/1m) 99 dB )1W/1m) 123 dB peak 128 dB peak 129 dB peak 134 dB peak 40 Hz to 120 Hz Model SSL12-10, 12” woofer; 800 W pgm @ 4 Ohms PNX 212SUB: Dual model SSL12-11, 12” woofer; 800 W pgm @ 8 Ohms (each) Enclosure: Multi-ply hardwood, perforated metal grille PN-1 AMPLIFIER Power Rating: Freq. Response: THD Distortion: Hum & Noise: Damping: Input: Sensitivity: CMR Controls: 300 W RMS @ 8 Ohms +0.0, -.5 dB, 20 Hz to 20 kHz < 0.02% typical <100 dB (A weighted) >100 10K Ohm balanced differential 1.0 V for RPO 74 dB Gain (screwdriver adjustable) Connectors Input: Looping XLR; female in, male out (pin 1 chassis, pin 2 +, pin 3 -) Power: IEC Power connector Power: 90-136 VAC or 180-260 VAC 50/60Hz. 4 A @ 120 V, 2 A @ 240 V Idle current: 300 ma @ 120 V; 150 ma @ 240 V Max inrush current: 10 A PN-1R RHAON EMPOWERED AMPLIFIER The PN-1R amplifier is identical to the PN-1 except for the addition of the RHAON Network Interface; additional capabilities include: Inputs: CobraNet; dual RJ45 connectors;accept CAT 5 copper cable. AES/EBU Phoenix connectors; Analog Phoenix connectors Digital Format: 16, 20 or 24 bit PCM; 48 or 96 kHz sample rate; selectable Network Latency. Protection: Soft & Peak Limiting, Excursion Control & Thermal Regulation For additional details on the RHAON Audio Operations Network, refer to www.renkus-heinz.com/Rhaon/Index.html Note: All analog inputs and outputs comply with AES Standard 48-2005 on interconnecting, grounding and shielding. DIMENSIONAL INFORMATION PN/PNX112SUB PN/PNX212SUB Metric M10 UMH (Universal Mounting Hardware) attachment points are standard on all fixed installation models. They are positioned 1 3/4" from the edges unless otherwise indicated. Portable models are normally supplied with a tripod socket and no attachment points. The rear views of PN series models are shown. The enclosure is shown without its metal grille. For more detailed dimensional information, please refer to the 2D and 3D drawing files on our website, www.renkus-heinz.com Renkus-Heinz, Inc., 19201 Cook Street, Foothill Ranch, CA 92610-3501, USA Tel: +1 949-588-9997 • Fax: +1 949-588-9514 • [email protected] • www.renkus-heinz.com RH490 Rev F April 2011 LIMITED WARRANTY LIMITED WARRANTY Renkus-Heinz warrants its products to be free from defects in material and workmanship for a period of six ( 6 ) years from the date of original purchase from Renkus-Heinz, except for the “WR” ( Weather Resistant ) models. “WR” models because of their exposure to the elements carry a 3-year Limited Warranty. This warranty is extended to the original purchaser and all subsequent owners, provided a copy of the original dated bill of sale is presented when service is requested under warranty. How to obtain service under this warranty If your Renkus-Heinz product should require service, write, phone, fax or email us. See info on the rear page. We will either direct you to a local service agency or provide you with a Return Authorization ( RA ) number so that you can ship the product to our factory. Do not ship WKHSURGXFWWRXVZLWKRXW¿UVWREWDLQLQJD5$QXPEHU3ODFHWKH5$QXPEHURQDOOER[HVUHWXUQHG to the factory. Merchandise returned to us for service under warranty must be accompanied by a copy of the original bill of sale, and shipped prepaid. You are responsible for transporting your product to our factory. We will pay the return shipping charges on all products repaired under warranty. Failures not covered by this warranty This warranty covers defects in manufacture only. It does not cover:  GDPDJHFDXVHGE\DFFLGHQWPLVXVHDEXVHSURGXFWPRGL¿FDWLRQRUQHJOHFW 2) damage incurred during shipment ( you must claim these damages from the carrier ). 3) damage resulting from failure to operate the product in accordance with the instruction manual; 4) damage resulting from attempted repairs by unauthorized personnel; 5) claims based on misrepresentations made by a sales agent of Renkus-Heinz. Page 2 1RJXDUDQWHHRIÀWQHVVIRUDSDUWLFXODUSXUSRVH 5HQNXV+HLQ]PDNHVQRFODLPVIRULWVSURGXFWVDVWR¿WQHVVIRUDSDUWLFXODUSXUSRVHDQG therefore does not guarantee the performance of any Renkus-Heinz equipment in a particular application ( such a guarantee is the dealer’s responsibility ). Renkus-Heinz guarantees that SURGXFWVZLOOSHUIRUPWRSXEOLVKHGVSHFL¿FDWLRQVZLWKLQWKHFRPPHUFLDOWROHUDQFHVDFFHSWHG in the industry ( errors and omissions are excluded from this guarantee ). /LPLWDWLRQRILPSOLHGZDUUDQWLHV All implied warranties, including warranties of merchantability, are limited in duration to a period of six ( 6 ) years from the date of original purchase from Renkus-Heinz, except for the “WR” ( Weather Resistant ) models. “WR” models because of their exposure to the elements carry a 3-year Limited Warranty. Refer to rear page for details. Exclusion of certain damages Renkus-Heinz’ liability is limited to the repair or replacement, at our option, of any defective product, and shall in no event include incidentally or consequential commercial damages of any kind. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the preceding limitation or exclusion may not apply to you. Enhanced Warranty on Reference Point Arrays and other integrated systems 2QLQWHJUDWHGLQVWDOOHGV\VWHPVLQZKLFKDOOFOXVWHUVRUORXGVSHDNHUV6\VWHP6SHFL¿F$PSOL¿HUV DQG/RXGVSHDNHU6SHFL¿F&RQWUROOHUVDUHGHVLJQHGDQGPDQXIDFWXUHGE\5HQNXV+HLQ]WKH six ( 6 ) year limited warranty described above is enhanced to include the replacement or reconing of diaphragms and woofers damaged by the malfunction of any Renkus-Heinz product in the system. Failures caused by errors in the initial wiring, or start-up accidents during system VHWXSLQLWLDOWHVWLQJDUHVSHFL¿FDOO\H[FOXGHG Page 3 WR ( Weather Resistant ) Models 1) Should be given preventive maintenance on a regular ( at least yearly) schedule; any exterior damage repaired, woofer cones retreated with moisture retardant, etc. 2) Should be given additional protection (rain hoods, for example) in areas where extreme weather conditions are common. 3) Self-Powered models should be left on continually in high-humidity applications. 19201 Cook Street, Foothill Ranch, CA 92610-3501 USA Phone: +1 949 588 9997, Fax: +1 949 588 9514 [email protected] www.renkus-heinz.com Page 4 RH352 July 2011 Rev. E