Transcript
LWL and LWR
MODELS LWR24 LWL48, LWR48 LWL511, LWR511 LIFT TYPE HAY RAKES
Published 04/11
MATERIAL HANDLING PARTS MANUAL
PARTS MANUAL SECTION 18
PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. For maximum safety and to guarantee optimum product reliability, always use genuine BUSH HOG Parts. The use of inferior replacement parts may causepremature or catastrophic failure which could result in serious injury or death.Direct any questions regarding parts to:
BUSH HOG 2501 Griffin Ave. Selma, AL 36703 www.bushhog.com Contact Us 800-304-2836
©2009 Alamo Group Inc.
To the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense!
WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty RegistrationForm in full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on theWarranty Card and on the Warranty Form that you retain.
LIMITED WARRANTY Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state and municipalities’ use and ninety (90) days for commercial use from date of retail sale. The obligation of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defective parts. Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety (90) days from the date of purchase of such part or to the expiration of the applicable new equipment warranty period, whichever occurs later. Warranted parts shall be provided at no cost to the user at an authorized Bush Hog dealer during regular working hours. Bush Hog reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship.
DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES Bush Hog’s obligation under this limited warranty, to the extent allowed by law, is in lieu of all warranties, implied or expressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE and any liability for incidental and consequential damages with respect to the sale or use of the items warranted. Such incidental and consequential damages shall include but not be limited to: transportation charges other than normal freight charges; cost of installation other than cost approved by Bush Hog; duty; taxes; charges for normal service or adjustment; loss of crops or any other loss of income; rental of substitute equipment, expenses due to loss, damage, detention or delay in the delivery of equipment or parts resulting from acts beyond the control of Bush Hog.
THIS LIMITED WARRANTY SHALL NOT APPLY: 1. To vendor items which carry their own warranties, such as engines, tires, and tubes. 2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident. 3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judgement of Bush Hog such use affects its performance, stability or reliability. 4. If the unit has been altered or repaired outside of an authorized Bush Hog dealership in a manner which, in the sole judgement of Bush Hog, affects its performance, stability or reliability. 5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid, worn blades, or to normal deterioration of such things as belts and exterior finish due to use or exposure. 6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in the company’s sole judgement is a wear item. NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIMITED WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE IN WRITING AND SIGNED BY BUSH HOG’S SERVICE MANAGER, 2501 GRIFFIN AVE., SELMA, ALABAMA 36703.
Record the model number, serial number and date purchased. This information will be helpful to your
MODEL NUMBER ________________________________ SERIAL NUMBER ________________________________
dealer if parts or service are required. DATE OF RETAIL SALE ___________________________ MAKE CERTAIN THE WARRANTY HAS BEEN FILED WITH BUSH HOG SELMA, ALABAMA
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
APRIL, 2011
ALPHABETICAL TABLE OF CONTENT SECTION 18 MODELS LWL24, LWL48, LWR48, LWL511, LWR511 ITEM
PAGE
LWL & LWR DECALS ....................................................................................18-1-5 LWL48 & LWR48 PARTS...............................................................................18-1-2 LWL511 & LWR511 PARTS ...........................................................................18-1-4 LWR24 REPAIR PARTS ................................................................................18-1-1
NOTES:
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
APRIL, 2011
LWR24 PARTS
REF. NO.
PART NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
3630213 3630214 N/A 3630101 70631C4 3637508 3737507 3637506 3637505 00755949 3637509 N/A N/A 3637504 N/A 700728C N/A N/A 3630100 61368C8 00755954 00755949 3637502 3638601 3637503 3638602 3638400 3638402
DESCRIPTION 3-Point Frame Sliding Arm Wheel Arm, Rh Wheel Assembly, Rh Carriage Bolt M10-1.25 X25 Tine Plate Tine Rim Flange Hex Nut M10-1.5 Weld On Spindle Seal Inner Bearing Wheel Hub Outer Bearing Castle Nut Cotter Pin M3.2 X 32 Hub Cap Hub And Spindle Assy. Capscrew M10-1.25 X 25 Lockwasher M10 Hex Nut M10-1.5 Lever Plate Lever Pin Pin Frame Pin Hair Pin Retaining Ring 18-1-1
QTY. NO. 1 1 1 2 40 20 80 2 2 40 2 2 2 2 2 2 2 2 2 12 12 12 1 1 1 1 2 2
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
APRIL, 2011
LWL48 &LWR48 PARTS
18-1-2
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
APRIL, 2011
LWL48 &LWR48 PARTS REF. NO.
PART NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
3630232 N/A 3630200 3638401 610611C8 N/A N/A 3630233 3638400 3638606 N/A N/A 2438312 70503 3637500 3637502 3630203 N/A 3638601 3630204 3637420 61377C8 3630205 00755954 700219C 3630234 3637501 3638402 3637503 3630102 3630101 15B1400 3630235 N/A N/A N/A 3637504 N/A 700728C 70477 N/A 3637506 3637505 61368C8 3737507 70631C4 3637508 N/A 3637509 3630100
DESCRIPTION
QTY. REQ’D.
3-Point Frame 1 Klick Pin 2 Stand 1 Hair Pin 2 Capscrew 1 Hex Nut M14-2 1 Hex Nut M10-1.5 105 Sector Support 1 Hair Pin 4 3-Point Pin 1 See Decal Page 2 Capscrew M14-2 X 10 Gr 8.8 1 Decal, Caution 1 Cotter Pin 2 Sector Support Pin 1 Lever Plate 3 3-Point Cap 1 3-Point Pin 1 Lever Pin 3 Upper Spring Mount 1 Extension Spring 2 Capscrew 1 Lower Spring Mount 1 Lockwasher 30 Hex Nut 1 Floating Arm 1 Lock Plate 1 Retaining Ring 6 Pin 3 Wheel Assy. L.H. 4 Wheel Assy.R.H. 4 Flatwasher 7/8" 2 Frame, 4wheel Models 1 Wheel Arm, L.H. 2 Seal 4 Inner Bearing 4 Hub 4 Outer Bearing 4 Castle Nut 4 Cotter Pin 4 Hub Cap 4 Rim 4 Flange 4 Capscrew M10-1.5 X 25 24 Tine - 7mm 160 Carriage Bolt 80 Tine Clamp 40 Wheel Arm, R.H. 5 Spindle, Weld On 1 Hub And Spindle Assy. 1 (Includes Spindle And Items 35-41) 18-1-3
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
APRIL, 2011
LWL511 & LWR511 PARTS
18-1-4
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
APRIL, 2011
LWL511 & LWR511 PARTS REF. NO.
PART NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53
3630200 3638401 3630232 3630233 3637500 15B1400 70503 3638606 3638400 N/A N/A 610611C8 3630203 61377C8 700219C 3630204 3637420 3630234 3630205 3637501 3637502 3638402 3637503 3638601 N/A N/A N/A N/A 3630238 3637509 3736800 3736000 3637504 3736001 700728C 70477 N/A 3630100 61368C8 00755954 00755949 70631C4 3637508 3637505 N/A 3637506 3737507 3630101 3630102 N/A N/A 61387C8 70096C
DESCRIPTION Parking Stand Cotter Pin 3-Point Frame Sector Support Sector Support Pin Flatwasher Cotter Pin M6.3 X 40 3-Point Pin Cotter Pin Capscrew M14-2 X 40 Hex Nut M14-2 Capscrew M10-1.5 X 85 Gr 8.8 3-Point Cap Capscrew M12 -1.75 X 30 Gr 8.8 Hex Nut M12-1.75 Upper Spring Mount Extension Spring Floating Arm Lower Spring Mount Lock Plate Lever Plate Retaining Ring Pin Lever Pin Rear Frame, 5 Wheel Model Wheel Arm, R.H. (Not Shown) Wheel Arm, L.H. Arm, Front, R.H. W/Hub Arm, Front, L.H. W/Hub Weld On Spindle Dust Cover Inner Bearing Wheel Hub Outer Bearing Castle Nut M18-1.5 Cotter Pin M3.2 X 32 Hub Cap Hub And Spindle Assy. Capscrew M10-1.5 X 25 Lockwasher M10 Hex Nut M10-1.5 Carriage Bolt M10-1.5 X 25 Tine Clamp Flange 3-Point Pin Rim Tine 3-Point Wheel Assy.,R.H. 3-Point Wheel Assy.,L.H. Klick Pin Front Frame, 5 Wheel Bolt Locknut, Toplock M14-2 18-1-5
QTY. REQ’D. 1 2 1 1 1 2 2 1 6 1 1 1 1 1 1 1 2 1 1 1 3 6 3 3 1 2 2 1 1 1 5 5 5 5 5 5 5 1 30 30 131 100 50 5 1 5 200 5 5 2 1 3 3
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
APRIL, 2011
DECALS
REF. NO.
PART NO.
1 2 3 4
50058089 999001 50068830 50068898 50068897 3200347 00776031 2738333 2738332
5 6 7 8
DESCRIPTION Bush Hog Logo Decal Warning Decal Important Decal Genuine Parts Decal, Model LWR Decal, Model LWL Smv Sign Canister, Owners Manual Amber Reflector Red Reflector
18-1-6
QTY. REQ’D. 2 1 1 1 1 1 1 2
2
2501 Griffin Ave.• Selma, AL 36703 (334) 872-6261 • (334) 874-2700 Parts Ordering 1-800-304-2836 Fax 1-800-572-1784 www.bushhog.com
