Transcript
CONTENTS FEATURES: ............................................................................................................................................... 2 SPECIFICATIONS:.................................................................................................................................... 2 DSCRIPTIONS OF MONITOR: (Power voltage:AC 100-240V) ............................................................. 3 DSCRIPTIONS OF MONITOR: (7/10.2 inch TFT 、Power voltage:DC 13.8V)................................. 4 DESCRIPTIONS OF MONITOR - REAR: (Power voltage:AC 100-240V) ............................................. 5 DESCRIPTIONS OF INDOOR -REARR: (10 inch TFT Power voltage:DC 13.8V)................................ 6 DESCRIPTIONS OF INDOOR -REAR: (7 inch TFT Power voltage:DC 13.8V)..................................... 7 DESCRIPTIONS OF MONITOR-CONNECTIONS: (10 inch TFT Power voltage:AC 110-240V)......... 8 DESCRIPTIONS OF MONITOR-CONNECTIONS: (10 inch TF Power voltage:DC 13.8V) ................. 9 DESCRIPTIONS OF MONITOR-CONNECTIONS: (7 inch TF Power voltage:DC 13.8V) ................. 10 SYSTEM DIAGRAM: ............................................................................................................................. 11 INSTALLATION GUIDE ........................................................................................................................ 12
DIAGRAM 1-1 MONITOR,1 DOOR BELL : ..............................................................13 DIAGRAM 2-1 MONITOR,2 DOOR BELLS:.............................................................14 WIRE DIAGRAM (2 MONITORS, 2 DOORBELLS) SYSTEM: ............................16 MONITOR INSTALLATION GUIDE: .........................................................................19 DOOR BELL INSTALLATION GUIDE: .....................................................................20 OPERATION GUIDE .............................................................................................................................. 21
How to answer the call from the doorbell and release the door lock? ..........................22 How to make visitor’s call transfer between indoor monitors? …………………………………22 How to enter supervision mode ? ………………………………………………………………….22 How to make intercom between indoor monitors?...........................................................................22 How to adjust Brightness/Contrast/Color? ……………………………………………………….23 How to setup CCTV1、CCTV2、door chime volume?..................................................................23 How to activate/cancel “Do Not Disturb” function? ……………………………………………...24
1
FEATURES: ¾ ¾ ¾ ¾ ¾ ¾ ¾
Surface-mounted, 7 / 10.2 inch color TFT screen with sensor buttons Support 2 indoor monitors and 2 doorbells Support 2-channel CCTV and 2 doorbells for security survelliance Outdoor station call, internal communication, visitor’s call transfer between monitors Connect TV., DVD and MP3 to watch TV and listen to music Color / contrast / brightness / ring volume adjustable Chime sound with 12 melodies selection
SPECIFICATIONS:
Display screen Horizontal resolution Power voltage Video input Video channel quantity Additional monitors quantity Power consumption Wiring mode Applicable temperature Dimension
7 / 10.2 inch TFT 420TVL AC 100~240V or DC 13.8V 75Ω 1Vp-p 4 2 1.5w ～16 w 4 wires，polar -10°C ~ 65°C 10.2 inch: 334（W）× 210（H）×25（D） 7 inch: 265（W）× 170（H）×25（D）
2
DSCRIPTIONS OF MONITOR:
3
(10.2 inch TFT ,Power voltage:AC 100-240V)
DSCRIPTIONS OF MONITOR:
4
(7/10.2 inch TFT, Power voltage:DC 13.8V)
DESCRIPTIONS OF MONITOR-REAR: (10.2 inch TFT, Power voltage:AC 100-240V)
DIMENSION:
5
DESCRIPTIONS OF MONITOR-REAR: (10.2 inch TFT Power voltage:DC 13.8V)
DIMENSION:
6
DESCRIPTIONS OF MONITOR-REAR: (7 inch TFT Power voltage:DC 13.8V)
DIMENSION:
7
DESCRIPTIONS OF MONITOR CONNECTIONS: (10.2 inch TFT, Power voltage:AC 110-240V)
8
DESCRIPTIONS OF MONITOR CONNECTIONS:
9
(10.2 inch TFF, Power voltage:DC 13.8V)
DESCRIPTIONS OF MONITOR CONNECTIONS:
10
(7 inch TFT, Power voltage:DC 13.8V)
SYSTEM DIAGRAM:
(Power voltage:AC 100-240V)
(Power voltage:DC 13.8V)
(Power voltage:DC 13.8V)
11
INSTALLATION
GUIDE
12
DIAGRAM 1-1 MONITOR, 1 DOOR BELL : 10.2 inch TFT, Power voltage:AC 100-240V
Notes: 1. The indoor monitor provides power directly to electric lock . 2. One extra 2-wire cable is needed to connect the electric lock to the indoor monitor. This method eliminates the need to provide a dedicated power supply to the electric lock, for high security. 10.2 inch TFT, Power voltage:DC 13.8V
13
Notes: 1. The electric lock is unlocked by the non-source contact signal from the door bell key. 2. An individual power supply is needed for the electric lock. This is a lower security method. If unauthorized persons understand the setup, they could dismantle the outdoor bell and short-circuit the 2-wired KEY cable, which would unlock the electric lock. 7 inch TFT, Power voltage:DC 13.8V
DIAGRAM 2-1 MONITOR, 2 DOOR BELLS : 10.2 inch TFT
Power voltage:AC 100-240V
14
10.2 inch TFT
7
inch TFT
Power voltage:DC 13.8V
Power voltage:DC 13.8V
15
WIRE DIAGRAM 10 .2 inch TFT
(2 MONITORS, 2 DOORBELLS) SYSTEM:
Power voltage:AC 100-240V
16
10.2 inch TFT
Power voltage:DC 13.8V
Notes: 1. When you operate the status switch, pls turn off the power. 2. when two MC-528F69-10 monitors are connected in a system, if the distance between the main monitor and the sub monitor is over 30 meters, stir the left statuse switch of the sub monitor upward. 3. When two MC-528F69-7 montiors are connected in a system, if the distance between the main montior and the sub monitor is over 30 meters, stir the sub monitor’s status switch on the second row upward.
17
7
inch TFT
Power voltage:DC 13.8V
Notes: when 2 monitors are connected in the system, pls set the status switch at the rear panel as follows;
18
MONITOR INSTALLATION GUIDE: Installation Instructions:
Please select relevant wire diagram in page 9 and 10 for your chosen system Make sure you use correct cable for system required.
Single Monitor Installations: Select correct height of indoor monitor ， usually installation height is between 150~160CM（See below Figure 1） After determine the monitor bracket position and run cable through the bracket， fix locating screws in bracket.
Finally, install the indoor monitor on the wall as below Figure 2.
19
DOOR BELL INSTALLATION GUIDE: Doorbell Installation: ¾ ¾ ¾ ¾
Please take some time to select the most suitable position for doorbell. Please consider the factors of day time, night time and likely weather condition impact. Direct sunlight on the camera and direct contact with rain should be avoided. Determine Camera Position: we recommend the door bell and the camera should be at the same height ( Average Height from 1.5 to 1.6 meters )
20
OPERATION
GUIDE
21
Operation Instruction How to answer the doorbell and release the door lock? When a visitor press the doorbell, the two indoor monitors will chime.You will see the visitor and know this call is from door 1 or door 2. Press “ ” button to answer, now you will have 60 seconds to talk with the visitor, or you can Press“ ” button to hang up. Press “ ” button , the door will be released within 2 seconds.
How to make visitor’s call transfer between indoor monitors? When a visitor calls from a doorbell, you wish to transfer this call to the other monitor , press the“ ” button again. Once the other indoor monitor receives the call, your monitor will hang up automatically. The conversation time will be 60 seconds.
How to monitor video and Audio input ? There are 4 Audio/Video channels that can be viewed individually at any indoor monitor.. The first two channels are Door-1 and Door-2 and provide both video and audio signals from each of the doorbell units. The next two channels are CCTV-1 and CCTV-2 which include inputs for both audio and video and can be used for television, background music or cameras equipped with microphones. You can supervise 4 channels from 2 indoor monitors and 2 door stations. channel 1 & 2 is for Door1 & Door2 video. Channel 3~4 is for 2 channel CCTV extension video. There are special audio input ports from CCTV1 & CCTV2 for watching TV and listening to music. More detailed information as belows: 1）Firstly, press“ ” button, to see image from door 1.. 2）Secondly, press“ ”button, to see image from door 2. 3）Thirdly, press “ ” button, to see image and hear sound from CCTV1. 4）Fourthly, press “ ” button, to see image and hear sound from CCTV2. When Door-1 or Door-2 is being monitored, the image will remain active at the monitor unit for 30 seconds and then reset. When CCTV 1 or 2 are being monitored, the image and sound (if applicable) will 22
remain
active until the function is turned off.
Note: If the chime is activated at one of the door units, while monitoring any of the other Audio/Video channels, the screen will automatically change to the visitor’s door stationl channel. The call can be answered as normal and when the call is terminated, the system will automatically return to the previous channel being monitored
How to make intercom between indoor monitors? When calling monitor at standby mode, press “ press“ ” button to answer.
” button, the other monitors will chime,
How to adjust Brightness/Contrast/Color? In intercom or surveillance mode, with an image on the screen, press “ ” button, the screen will display “brightness”level, use “ or ” button to adjust brightness to the desired level. With the Brightness level displayed, press the “ “ to diplay the “Contrast” level , use “ or ” button to adjust Contract to the desired level. With the Contrast level displayed, press the “ “ to diplay the “Colour” level , use “ or ” button to adjust Colour to the desired level Press “ ” button to save and return to the main menu interface，press “ again to turn off the screen and exit.
23
” button
How to choose chord ring ? There are 12 chords ring available. Set as follows: Press the doorbell, the monitor chime and display the pictures, press “ chord. Every time press the button, it will change to another chord, press“ will be off. The chord chosen will chime next time when there is a call.
” button to change the ” to save and the screen
How to setup CCTV1、CCTV2、door chime volume? When you are watching TV or listenning to music through CCTV1 or CCTV 2 channel, Press “
“
“ or
” to adjust the volume to the desired level.
When the outdoor station calls the indoor monitor, press “
” or “
” to adjust the door chime
volume.
How to activate/cancel “Do Not Disturb” function? When you don’t want to be disturbed by the chime from an indoor monitor, you can activate the “Do Not Disturb function.” There will be no sound from the monitor when the doorbell is activated or when the other monitor call is initiated. The chime will only sound when the monitor call the other monitor.
Activation procedure: In standby mode, press the “ ” button for 2 seconds at any indoor monitor, the “ “ will turn red and enter into “Do Not Disturb” mode. In Do Not Disturb mode, the monitor can still see the image from the front door and can still answer the call. ” button for 2 Do Not Disturb mode can be deactivated by once again pressing the “ “ seconds while in standby mode, the “ ” will turn from red to normal to exit “Do not Disturb Mode.”
24
25
