Transcript
R
SHS AUDIO
SPMU- 1060 CABINET POWERED MIXING CONSOLE
USER'S MANUAL
SAFETY INSTRUCTIONS WARNING - TO REDUCETHE RISK OF FIRE OR ELECTRICSHOCK, DO NOT EXPOSETHIS UNIT TO RAIN OR MOISTURE.
SPECIFICATIONS Inputs
Input modes
Input Impedance
Rated Input level
Connector
MONO MIC
Balanced
3Kohm
-60dB
Mono LINE IN
Balanced
47Kohm
-40dB
XLR 3-poles TRS
Stereo LINE IN
Unbalanced
10Kohm
-10dB
2 TRS
Stereo PLAY IN
Unbalanced
10Kohm
-10dB
2 RCA
Outputs Impedance
Rated Output Level and Power 2X200W 2X300W 800W
Connector
Outputs
Outputs modes
This triangle on your component alerts you
This triangle on your component alerts you
to the presence of uninsulated
to important operating and maintenance in-
L/R Power OUT
Unbalanced
structions in this accompanying literature.
BRIDGE OUT
Unbalanced
8ohm 4ohm 8ohm
L/R LINE OUT
Unbalanced
600ohm
0dB
TRS
Monitor OUT
Unbalanced
600ohm
0dB
TRS
Stereo REC OUT
Unbalanced
10Kohm
-10dB
Stereo Effect OUT
Unbalanced
600ohm
0dB
voltage
dangerous
inside the enclosure that may be
sufficient to constitute a risk of shock.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVERS (OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER ALL SERVICING TO A QUALIFIED SERVICE PERSONNEL.
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink, in a wet base --ment, or near a swimming pool, or the like. The products should be located so that its location or position does not interfere with its proper ventilation. The product should be located away from heat sources such as radiators, heat resistors or other products that produce heat. The product should be connected to a power supply only of the type described in the operating instructions or as marked on the rear panel of the product. The power supply cord of the products should be unplugged from the outlet when left unused for a long period of time. Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. The product should be serviced by qualified service personnel when: 1. The power supply cord or the plug has been damaged; or 2. Objects have fallen, or liquid has been spilled into the product; or 3. The product has been exposed to rain; or 4. The product does not appear to operate normally or exhibits a marked change in performance; or 5. The product has been dropped, or the enclosure damaged Do not attempt to service the product beyond that described in the user-maintenance instructions. All other servicing should be referred to quality service personnel. CAUTION Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly. Material damage refers to damage or other adverse effects caused with respect to the home and all its furnishings, as well to domestic animals or pets.
1
TRS
Output
Max gain
MONO MIC IN
L/R POWER OUT
88dB
MONO MIC IN
L/R LINE OUT
66dB
MONO MIC IN
MONITOR OUT
66dB
MONO MIC IN
REC OUT
56dB
MONO MIC IN
EFFECT OUT
70dB
MONO LINE IN
L/R LINE OUT
46dB
STEREO LINE IN
L/R LINE OUT
20dB
≤0.5%
DSP
20Hz ~ 20KHz
+1dB, -2dB 20Hz ~ 20KHz
Microphone preamp E.I.N Channel EQ Graphic EQ Power supply
TRS
2 RCA
Input
Total harmonic distortion Frequency response
TRS
-120dB
@ 150ohm , at max gain
HI 15KHz MID 2.5KHz LOW 80Hz max equalizing value +/-15dB 63Hz, 125Hz, 250Hz, 500Hz, 1KHz, 2KHz, 4KHz, 8KHz, 16KHz +/-12dB AC110V/220V; 120V; 220V; 230V Refer to the nameplate on the rear panel. 8 kinds effects status, 24bit DSP, 48KHz sample rate
Power consumption
1000VA MAX
Weight
21Kg
Dimension
480X308X290mm
10
CONNECTION EXAMPLE
BRIEF INSTRUCTION Thank you for purchasing SPMU-1060 cabinet powered mixing console.
LEFT
SPMU-1060 has seven mono input channels, two stereo line input channels and a stereo playback input channel. The output power of mixer is 2X300W@4ohms or 2X200W@8ohms, bridge mode.
RIGHT
For the variety level signal input and the convenience of usage, the MONO input channel has a MIC input socket, a LINE input socket and a input level attenuation switch, the stereo input channel also has a MIC input socket and a LINE input socket. Every channel has HI, MID, LOW equalization circuit, monitor output and effect output. The independent playback channel has HI, LOW equalization circuit and monitor output. There are 7-band graphic equalizer for the LEFT & RIGHT outputs and the monitor output to embellish the timbre. And the built-in digital effects processor provides 16 different kinds sound field effects.
POWER AMP
EFFECT PROCESSOR
LINE OUT
EFF SEND
OUTPUT
EFX RET CH A
CH B
Besides stereo PA output, this series mixer also has stereo LINE outputs, independent monitor outputs and record outputs. Furthermore, the effect signal send-return sockets have been used for the external effects processor.
REC OUT L/R
TAPE IN L/R
CASSETE PLAYER
FT SW
MIC IN
MIC IN
LINE IN L/R
LINE IN L/R
9
The built-in power amplifier has manifold protectors and uses air cooling for heat emission. By using the working mode selector, you can choose to output stereo signals or mixing signals and monitor signals. Also the unit can working at BTL bridge mode. This mixer has consummate functions and perfect shape. And two kinds of exterior you can choose, the wooden case with handles or the 19 inches cabinet with handles, so that you can install it everywhere you want.
2
Safety Instructions
1
Brief Instruction
2
Mono Input Section
3
Stereo Input Section
4
Playback Input Section
5
Master Control Section
6
Rear Panel Section
8
Connection Example
9
Specifications
10
1
2 MID: Controls the midrange content of the input signal, the maximum adjustment region is 2.5KHz ±15dB.
2
3 LOW: Controls the bass content of the input signal, the maximum adjustment region is 80Hz ±15dB.
3
4
4 EFF: Controls the signals' level which are sent to the effect bus. The effect signals are sampled after the channel level controller and controlled by channel level controller. Adjust this knob to control the signal level when connecting a effects processor, otherwise rotate the knob to zero position.
5
5 MON: Controls the signals' level which are sent to the monitor bus. The monitor signals, which can be used as monitor output or AUX output, are sampled before the channel level controller and cannot be controlled by the channel level controller.
6
6 PAN: Controls the signal level ratio between left channel and right channel. Turn the knob to the middle position to make the signal level of left channel and right channel equal.
7 8 9 10
11
1
AC~
2
3
POWER VOLTAGE SELECTOR
1 HI: Controls the treble content of the input signal, the maximum adjustment region is 15KHz ±15dB.
REAR PANEL SECTION
USE ONLY WITH 250V FUSE
MONO INPUT SECTION
220
FUSE
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE WITH SAME TYPE AND VALUE FUSE INDICATED. WARNING: TO REDUCE THE RISK OF FIRE OF ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
FOR PROTECTION AGAINST DAMAGE OF YOUR POWER AMPLIFIER, PLEASE DO NOT CONNECT THE RIGHT/MON OR THE LEFT/MAIN SOCKET AND THE BTL SOCKET WITH LOAD SIMULTANEOUSLY.
RIGHT/MON
BTL
LEFT/MAIN
TOTAL LOAD ≥ 4ohm
TOTAL LOAD ≥ 8ohm
TOTAL LOAD ≥ 4ohm
5
6
7 LEVEL: Controls the channel's output level. Please rotate the knob to zero position when the channel is not used. 8 PFL: Press this button to monitor the input signals of the channel by headphone. The monitor signals are sampled before the channel level controller, cannot be controlled by the channel level controller. 9 PAD: Pushbutton to reduce 25dB incoming signal level to avoid overload. 10 LINE: 1/4 inch balanced jack connector for balanced line level inputs, rated input level is -40dB ~ -15dB. 11 MIC: XLR electronically balanced input for microphones, rated input level is -60 ~ -35dB. +48V DC supply to all capacitor microphones when the phantom power switch is turned on.
3
4 1 AC & FUSE: Connects the AC power and holds the fuse. 2 POWER SWITCH: Turn on&off the AC mains power.
3 VOLTAGE SELECTOR: Selects the right voltage of your country. After you selected the right voltage, please fix the organic glass panel for preventing the damage caused by mis-operation. 4 RIGHT/MON: Three parallel-connected sockets. Outputs the PA signals of right channel or monitor channel, total load impedance should large than 4ohms. 5 BTL: Two parallel-connected sockets. When the power amplifier is working at bridge mode, these two sockets outputs PA signals, total load impedance should large than 8ohms. 6 LEFT/MAIN: Three parallel-connected sockets. Outputs the PA signals of left channel or the mixing PA signals of mixer's left&right channels, total load impedance should large than 4ohms. CAUTION: FOR PROTECTION AGAINST DAMAGE OF YOUR POWER AMPLIFIER, PLEASE DO NOT CONNECT THE RIGHT/MON OR THE LEFT/MAIN SOCKET AND THE BTL SOCKET WITH LOAD SIMULTANEOUSLY.
8
MASTER CONTROL SECTION
STEREO INPUT SECTION
1
1 HI: Controls the treble content of the input signal, the maximum adjustment region is 15KHz ±15dB. 2 MID: Controls the midrange content of the input signal, the maximum adjustment region is 2.5KHz ±15dB.
2 8
9
10
11
12
13
14
8 REC OUT: Two RCA pin jacks for stereo record signal output.
3
9 LEFT: Left channel volume controller for controlling the mixer's left channel volume. 10 RIGHT: Right channel volume controller for controlling the mixer's right channel volume. 11 MODE SWITCH: Power amplifier working mode selector. There are three mode for choosing. L/R mode: Two power amplifier's channels amplify mixer's left&right channel signals separately. MAIN/MON mode: One of the power amplifier's channel amplify the mixing signals of mixer's left&right channels. Another power amplifier's channel amplify the mixer's monitor signals. BTL mode: Two power amplifier's channels working at the bridge mode, amplify mixer's mixing signals of left&right channels. 12 MAIN: Master output level controller for controlling the mixing signal level of left&right channels.
4
5
6
6 BAL: Controls the signal level ratio between left channel and right channel. Adjusting the balance of stereo sound image.
7 8 9
15
16
17
18
19
20
7 LEVEL: Controls the channel's output level. Please rotate the knob to zero position when the channel is not used. 8 PFL: Press this button to monitor the input signals of the channel by headphone. The monitor signals are sampled before the channel level controller, cannot be controlled by the channel level controller. 9 L/MONO & R: Two 1/4 inch unbalanced jacks for stereo line input, rated input level is -10dB. If the incoming signal is MONO signal, please just use the L/MONO jack.
21
15 PHANTOM: Phantom power switch and indicator. Press the button to supply +48V DC to all microphone. Notice: Before turn on or turn off this switch, you must turn off the level controller of all channels. Do not unplug the MIC when this switch is turned on. Do not turn on this switch when you using an electrodynamic microphone.
4 EFF: Controls the signals' level which are sent to the effect bus. The effect signals are sampled after the channel level controller and controlled by channel level controller. Adjust this knob to control the signal level when connecting a effects processor, otherwise rotate the knob to zero position. 5 MON: Controls the signals' level which are sent to the monitor bus. The monitor signals, which can be used as monitor output or AUX output, are sampled before the channel level controller and cannot be controlled by the channel level controller.
13 MON LEVEL: Monitor output level controller for controlling the signal level of monitor output. 14 HEADPHONE: Headphone socket and volume controller for connecting the headphone and controlling its volume.
3 LOW: Controls the bass content of the input signal, the maximum adjustment region is 80Hz ±15dB.
10
10 MIC: XLR electronically balanced input for microphones, rated input level is -60 ~ -35dB. +48V DC supply to all capacitor microphones when the phantom power switch is turned on.
16 MON OUT: 1/4 inch unbalanced jack for monitor signal output, rated output level is 0dB. This socket also can be used for other AUX output and connect external monitoring amplifier. 17 LINE OUT: Two 1/4 inch unbalanced jacks for LEFT and RIGHT line output, rated output level is 0dB. 18 POWER AMP IN: Two 1/4 inch unbalanced jacks for signal insert. When signals are inserted from these two sockets, the connection between mixing console and power amplifier will be cut off automatically, and the power amplifier will amplify the signals come from these two sockets directly. 19 EFF SEND: 1/4 inch jack for LEFT & RIGHT effect signals output. The signal can be use as input signal for external effects processor. 20 EFF RET: 1/4 inch jack for the LEFT & RIGHT effect signals of external effects processor input. If you connect the external effects processor, the signal of built-in effects processor will be cut off automatically. 21 FT SW: 1/4 inch jack for exclusive use pedal switch. It can control the connection of effect signal.
7
4
PLAYBACK INPUT SECTION 1
2
1
TAPE IN: Two RCA pin jacks for stereo playback input, rated input level is -10dB.
2
HI: Controls the treble content of the input signal, the maximum adjustment region is 15KHz ±15dB.
3
LOW: Controls the bass content of the input signal, the maximum adjustment region is 80Hz ±15dB.
4
MON: Controls the signals' level which are sent to the monitor bus. The monitor signals, which can be used as monitor output or AUX output, are sampled before the channel level controller and cannot be controlled by the channel level controller.
3
5
BAL: Controls the signal level ratio between left channel and right channel. Adjusting the balance of stereo sound image.
6
LEVEL: Controls the channel's output level. Please rotate the knob to zero position when the channel is not used.
4
5
MASTER CONTROL SECTION 1
EFF SELECT: Effects selector for selecting the effect you want to play (refer to the effects table below the selector).
2
EFF SEND: Effect output level controller for controlling the effect signal level that is sent to the built-in effect processor or output from EFF SEND socket.
3
EFF TO MON: Monitor effect output level controller for controlling the effect signal level of monitor output.
4
EFF TO MAIN: Main effect output level controller for controlling the effect signal level of main output.
5
USB PORT: This unit built-in a music player, An U disk which loaded many songs easily can be a good quality line signal source via this port.
6
Controls for built-in MP3 player: These keys allows you operate the built-in music player.
7
Display for built-in MP3 player: This LCD display shows all kinds of status of the built-in music player.
8
SD Card: A SD Card which loaded many songs easily can be a good quality line signal source via this port.
6
11 10 9 8 7
1
12 13 14
6 5 4
15 16 1 2 3
5
11
10
11
2
EFF SELECT CHORUS FLANGE DELAY 1 DELAY 2 CHORUS/ROOM 1 14 CHORUS/ROOM 2 15 VOCAL CANCEL 16 ROTARY SPEAKER
1 HALL 1 2 HALL 2 3 ROOM 1 4 ROOM 2 5 ROOM 3 6 PLATE 1 7 PLATE 2 8 PLATE 3
9
9 10 11 12 13
USB/SD
VOL+
VOL-
8
9
MAIN EQ: 7-band stereo graphic equalizer for equalizing the frequency of the main channel's left & right outputs.
EFF SEND EFF TO MON EFF TO MAIN
10 MON EQ: 7-band stereo graphic equalizer for equalizing the frequency of the monitor output. 0
10
2
0
10
3
0
10
4
7
6
5
11 L/MAIN & R/MON: Two groups of indicators indicate the level of stereo line output and the output power of power amplifier. When the red indicator is lighten, the output power of power amplifier reach a maximum.
6
