Transcript
Quick Guide 2in1 Alert/Alarm System Protect your Home the Smart Way!
Model: M9
1. Safety Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interferences that may cause undesired operation.
3. Setup the Main Console
4. Insert Batteries in the Sensors
5. Testing the Door/Window Sensor
NOTE: 9 x AAA and 2 x AA-Batteries are required to setup the Alert/Alarm System. (AA/AAA Batteries are not included.)
1. Plug in the power adapter to the Main Console and rotate the antenna to the upright position for the best signal reception.
1. Push the both sides in and open the cover of the Door/Window Sensor to insert an AAA Battery.
NOTE: The Door/Window Sensors are factory preset in Zone 1.
Warning:
3. The Main Console will continue beeping and the Zone LED will flash if the door is open.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2. Use a coin to open the Motion Sensor and insert an AA Battery.
Main Console
CE Declaration of Conformity This equipment complies with the requirements relating to electromagnetic compatibility, EN 301489-1, EN301489-3, EN300220-1, EN300220-2 and EN60950-1. This equipment conforms to the essential requirement of the 1999/5/EC R&TTE Directive.
4 x Door/ Window Sensor
2 x Motion Sensor
www.skylinkhome.com
6. Testing Motion Sensor
Power LED Steady green is normal and flashing green indicates low backup battery status.
LED Zone Indication Shows the status of the sensors in that zone or the status when programming.
Antenna
9. Security Keypad Overview
10. Change passcode and install the Keypad
NOTE: The backlight will turn on when pressing the buttons. The factory default Pin is 0,0,0,0.
NOTE: The factory default passcode is 0,0,0,0. The passcode can be 2-8 digits long and with a combination of buttons from 0-6.
Disarm
Enter PIN number and tap the Button to disarm the alarm system.
Select “Arm Away” to protect your home when you’re away. This mode gives you 45 seconds exit delay to leave the house. It will also give you 30 seconds entry delay to disarm the system when you are back.
Arm Home
Enter PIN number and press “Arm Home” to protect while you’re at home. This mode deactivates motion sensors but leaves other sensors activated.
Select “Arm Home” to protect while you’re at home. This mode deactivates motion sensors but leaves other sensors activated with instant alarm.
AC Adapter Input Jack Mute Button To disable the beep sound temporary.
Enter PIN number and press the “Arm Away” to protect your home when you’re away. This mode activates or triggers the alarm after a default set of time, giving you enough time to get in and out of your house to arm/disarm the alarm system.
Tap the Button to disarm the alarm system.
LED
Alert Notification Switch Select the type of audio alert signal. OFF | CHIME | ALERT Learn Button To program and erase sensors.
Panic Button
Press and hold the Panic Button for 3 sec. to activate the alarm.
1. Input current PIN [factory default 0 0 0 0] and press 2. Input the new PIN number followed by 3. Input the new PIN again and press
3. The main console will beep continuously and flash the Zone 1 LED if the door is open.
4. Move the magnetic contact back to the sensor and the alert sound will stop.
Panic Button
Press the Panic Button to activate the alarm.
11. Install the Door/Window Sensor Place the sensor in the appropriate location:
button.
button.
button.
If the Keypad emits 2 beep, your pin has been successfully changed. If it emits a long error beep, start from step 1 again.
Arm Away / Exit Away
Disarm
(BACK)
* As an energy saving feature, the motion sensor will not be triggered again unless there is no motion detected for 15 seconds. In this case, the red LED will only flash once indicating the motion is detected, but no signal is sent to the Internet Hub.
Mounting Accessories
Arm Home (FRONT)
2. Activate the Sensor by separating the magnetic contact of the sensor.
3. Undo the screw on the bottom side of the Security Keypad to remove the back plate and insert an AAA Battery.
Arm Away / Exit Away
1. Slide the switch at the back of 2. Move in front of the motion the Main Console to alert mode. sensor to trigger the sensor. The red LED on the sensor will flash multiple times.
4. The Main Console will stop beeping and flashing the LED after 15 seconds.
Power Adapter
Security Keypad
1. Slide the switch at the back of the Main Console to alert mode.
2. Insert 4 x AAA-Batteries in the Main Console for backup power in case of power outage. (Optional)
LED
LED Armed Indication Shows if the Alarm System is armed or disarmed.
LED
Security Keychain Remote
8. Keychain Remote Overview
7. Main Console Overview
NOTE: The Motion Sensors are factory preset in Zone 2.
3. The Main Console will continue beeping and the Zone 2 LED will flash if a motion is detected.
2. Package Content
Back Plate
Screw
1. Undo the screw on the bottom of the Keypad and remove the back plate. 2. Mount the back plate with the included Screws. 3. Attach the Keypad on the back plate and tighten the screw on the bottom of the Keypad.
Mount the Door/Window Sensor on your door or window with double sided tape.
12. Install the Motion Sensor
13. Operation of Alarm System
Place the sensor in the appropriate location: Arm Away Arm Home
Arm Home Arm Away
14. Enable Chime or Alert Mode
1. Arm your alarm system by pressing the “Arm Away” or “Arm Home” button on the Security Keychain Remote or by entering your PIN number followed by the “Arm Home” or “Arm Away” button on the Security Keypad Console.
1. Slide the switch at the back of the Main Console to enable Chime or Alert Mode.
15. Alert Notification
16. Program Security Remote/Keypad Console
17. Program W/D Sensor to Main Console
When the Alert Mode is activated, you can identify the zone number by the number of beeps.
NOTE: The Keychain Remote must be programmed in Zone 1. You can program up to 4 Remotes or Keypads with the Main Console.
NOTE: You can program up to 4 sensors in each Zone.
ZONE 1 SENSORS - 1 Beep , Pause , 1 Beep , Pause ... etc. ZONE 2 SENSORS - 2 Beep , Pause , 2 Beep , Pause ... etc. ZONE 3 SENSORS - 3 Beep , Pause , 3 Beep , Pause ... etc.
1. Press and hold the “Learn” button for 3 seconds, until the Zone 1 LED is flash.
ZONE 4 SENSORS - 4 Beep , Pause , 4 Beep , Pause ... etc.
2. When a sensor get triggered, the main console will sound a siren and the corresponding zone LED will flash for 3 minutes.
Disarm
The motion sensor can be mounted with a double sided tape or screws in a corner, straight wall, ceiling or stand freely by itself.
3. Press the “Disarm Button” on your Keychain Remote or enter the PIN number and press the “Disarm Button on the Keypad Console to deactivate the alarm system.
The beeping will continue until the sensor is deactivated. When the Main Console receives a signal from the motion sensor, the Main Console will beep and the LED will flash on the corresponding zone for 15 seconds.
Chime Mode
Alert Mode
When chime mode is enabled
When alert mode is enabled
and your Skylink Alarm System
and your Skylink Alarm System
is disarmed, the Main Console will
is disarmed, the Main Console will
beep every time a sensor gets
beep continously when a window/
triggered.
door is opened or motion is detected
Press the MUTE button if you want to temporarily disable the beeping sound.
2. Press any button to program the Security Keychain Remote or enter the PIN number followed by the “Disarm Button” to program the Security Keypad Console.
3. Once the Security Keychain Remote or Keypad Console is programmed, the Main Console will beep once and the corresponding zone LED will be off.
until the sensor is deactivated.
1. Press and hold the “Learn” button for 3 seconds, until the Zone 1 red LED flash.
2. Zone 1 is selected. Press the learn button to select the Zone you want to program the sensor.
3. Activate the Sensor by separating the magnetic contact of the sensor.
4. Once the sensor is programmed, the Main Console will beep once and the corresponding zone red LED will be off.
Disarm
18. Program Motion Sensor to Main Console NOTE: You can program up to 4 sensors in each Zone.
19. Zone Settings Refer to the chart below for the 2 zone operation modes. The unit is currently set at Default Zone Setting Mode.
Zone Setting
1. Press and hold the “Learn” button for 3 seconds, until the Zone 1 red LED flash.
2. Zone 1 is selected. Press the learn button to select the Zone you want to program the sensor.
Zone
Default Zone Setting
Special Zone Setting
Suggestion Application
Zone 1&2
Alert when disarmed, Alarm when armed.
Alert when disarmed, Alarm when armed.
Most sensor, except for sensors in outdoor or high traffic area.
Zone 3
Zone 4
No alert when disarmed, but will alarm when armed.
Alert Only, No Alarm.
Alert when disarmed, Alarm when armed.
Indoor motion sensor in a high traffice area.
Alert when disarmed, Alarm when armed.
For outdoor sensor.
Change between Default Zone and All Alert Zone Mode:
3. Open the Motion Sensor cover with a coin and press the learn button.
4. Once the sensor is programmed, the Main Console will beep once and the corresponding zone red LED will be off.
1. Power up the Main Console. 2. Press and hold the “Learn” and “Mute” button simultaneously for 5 seconds, until you hear the beep. 3. If you hear one beep, you are in “All Alert Zone Setting” and if you hear 2 beeps, you are in “Default Zone Setting”. 4. Release both button.
20. Sensor Failure/Battery Indication
21. FAQ
If the signal is lost between the sensor and the Main Console, or if the battery in the sensor is low, the zone LED light will start blinking fast.
The Main Console does not respond to the sensor, keychain remote or Keypad Control? - You must program the sensor or keypad to zone 1 of the main unit before they can work together. - Ensure to input the correct password on the Keypad. - Ensure to input the correct password if enable the password feature in keychain remote.
Take the following steps to troubleshoot the problem: 1. Check if the sensor is located where it should be, and whether there is any physical damage to the sensor. 2. If the failed sensor is not physically damaged, try to activate the sensor and see if the Main Console reacts to the activation. 3. If not, try to remove the sensor from its location, and bring it closer to Main Console and then activate the sensor. It is possible that the sensor is installed too far from the Main Console and it cannot establish a steady communication with the Main Console. If this is the case, please install the sensor closer to the Main Console. 4. Replace the battery of the sensor in that zone if the Main Console does not respond even when the sensor is near the Main Console. NOTE: If you have multiple sensors in a zone, you may test the function of each sensor to identify which sensor is having a problem.
Can I erase just one sensor or remote from a zone? - You must erase all the sensors/remotes in that zone and then program the remote you want to keep. I have multiple remotes in a zone and the zone LED keep flashing that is a remote failure, how do I know which sensor/remote is having the problem? - You need to test each remote/keypad/sensor individually. Can I only use battery to power up the Control Panel? - It is recommended to power up the control panel with AC adapter. Install batteries to the Control Panel so it can continue to operate during power failure.
22. Erasing the Sensors/Remote from the Main Console NOTE: To erase any sensors or remote from the Main Console, you need reset the Main Console and learn the sensors/remotes you wish to keep.
1. Remove the power adapter from the Main Console.
23. Warranty / Customer Service This product is guaranteed to be free of defects in materials and workmanship for 1 year from the date of purchase. If this product is defective, call 1-800-304-1187 for repair or replacement parts. Guarantee does not include normal wear and tear or batteries.
2. Press and hold the Learn Button and plug in the power adapter back in the Main Console. 3. Release the learn button when the red LED are flashing on the Main Console. 4. You have successfully erased all sensors and remotes from the Main Console.
If you have any questions, problems or missing parts, please call:
Skylink Customer Support
Learn Button AC Adapter
1-800-304-1187
LED
9:00am – 5:00pm EST, Monday-Friday. Or e-mail us at
[email protected] www.skylinkhome.com
Repeat the above steps to change between 2 operation modes.
P/N:101Y184
