Transcript
Specifications English
Metric
Size
6.1 x 5.0 x 1.4”
155 x 127 x 35 mm
Weight
7 oz
200 g
Temperature range Non-contact (IR) -4 to +1,832° F Contact (K) -148 to +2,192° F
-20 to +1,000° C -100 to +1,200° C
Accuracy Non-contact (IR) <32° F: ±5° F / >32° F: ±3.5° F Contact (K) ±2% or ±2° F whichever is greater
<0° C: ±3° C / >0° C: ±2° C ±2% or ±2° C whichever is greater
Temperature Operating +32 to +120° F Storage -13 to +158° F (without battery)
0 to +50° C -25 to +70° C (without battery)
Power supply Response time Spectral response Emissivity, fixed
TempMate handheld IR thermometer Quickstart guide
Laser sighting
Easy to read backlit display
1 9V battery (alkaline or NiCd) 500 milliseconds 7 ~ 14 μm
CE certified
0.95
About us Meggitt Sensing Systems is a leading innovator and manufacturer of vibration sensing products and systems. Our reputation for industry-leading product quality and reliability is backed by more than 60 years of innovation and experience.
Trigger button
Single battery operation
Monitoring changes in vibration and temperature can be critical in preventing damage to equipment and costly delays. The quality and performance of our products ensure accurate and continuous monitoring of machinery health, enabling condition based maintenance of both critical and balance of plant assets. Sensors for every application >> Hazardous area certified >> 4-20 mA output >> Low/high frequency >> Dual output >> High temperature >> 4-20 mA output >> Triaxial >> Radiation resistant
Meggitt Sensing Systems 20511 Seneca Meadows Parkway Germantown MD 20876 USA
Accessories >> Transmitters and alarms >> Cable assemblies >> Mounting hardware >> Handheld meters >> Enclosures
[email protected] www.wilcoxon.com www.meggitt.com
Contact and non-contact readings
Tel: +1 (301) 330 8811 Fax: +1 (301) 330 8873
Applications HVAC/R Oil & gas Food and beverage Manufacturing processes
Easily monitor Steam traps Bearing housings Transformer oil Circuit breakers
TempMate IR thermometer
Taking a reading
The handheld MAC050 meter assists in temperature readings of hard-to-reach or moving industrial machinery.
Press and hold the trigger. The thermometer will power up and the laser will be visible (unless in contact mode). After releasing the trigger, the MAC050 will display the last reading and automatically turn off after 10 seconds. For extended measurement time simply hold down the trigger and the unit will stay in scan mode.
Using laser sighting, MAC050 enables users to safely take readings from critical machinery like pumps, motors, fans and bearings. A K-type thermocouple probe is supplied for applications where emissivity is unknown.
Safety considerations Never point the laser beam at someone’s eyes or look directly into the beam. Use caution when measuring a shiny surface so the laser does not reflect back into your or someone else’s eyes. Do not touch the lens to foreign objects. Do not expose the unit to damp environments for extended periods of time.
Maintenance and care The MAC050 is powered by a 9 volt alkaline battery (included). Replace the battery when the low battery indicator appears on the LCD by removing the battery compartment cover. Clean the surface and optical lens with a damp cloth.
Service and warranty The MAC050 is covered by a 3 year warranty, in the unlikely case of malfunction, please email
[email protected] for an RMA number.
Troubleshooting Temperature seems inaccurate • • • • •
Dirty optical lens Low battery Unit is too far from target Poor emissivity qualities of surface Laser out of alignment
Unit/laser does not power on • • •
Dead or low battery Defective power on switch Broken battery/laser connector
Email
[email protected] for more information Full product manual available at www.wilcoxon.com
Measurement modes The selector switch is located inside the battery compartment in the handle. Position the switch to the left for non-contact measurements (IR) or to the right for contact measurements (K). Infrared (IR) mode
1. Set the IR/K switch to IR (left). 2. Hold down the trigger to turn the unit on. 3. Align the laser with the target, holding the front of the meter at least 9 inches from the target (spot size will be 1 inch when 9 inches away). 4. Read the temperature on the LCD.
Thermocouple (K) mode
A K-type probe must be connected to the K-type connector or the thermometer will display OPEN when the trigger is pulled. 1. 2. 3. 4. 5.
Set the IR/K switch to K (right). Connect the thermocouple probe to the input jack on the bottom of the handle. Hold down the trigger to turn the unit on. Touch the thermocouple to the item under test. Read the temperature on the LCD screen. K °C
Selecting F or C
IR
°F
Acces the selector switch located above the battery compartment in the handle. Position the switch to the left for Celsius or to the right for Fahrenheit.
Recall last reading To recall the last reading before the unit powered off, quickly press and release the trigger. The last reading will be displayed for an additional 10 seconds.
MAC050 handheld thermometer Instant readings for machinery health and diagnostics
