Transcript
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103 The MJ-6103 Hole Punch Unit can be installed in the MJ-1101/1106 Finisher. The set-up procedures vary slightly depending on the Finisher in which the Hole Punch Unit is installed. Refer to the unpacking or set-up procedure for the corresponding model. MJ-1101
MJ-6103
Menu
Main Menu
MJ-1106
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
1
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
OFF
Be sure to shut down the equipment and unplug the power cable before any option is installed. The procedure for the shutdown is as follows: - Press the [ON/OFF] button until you hear a sound. - Confirm that the ON/OFF lamp is out. - Turn the power OFF with the main power switch. Be sure to install the equipment near an electric outlet so that it is easily accessible. * For Japan, remove the ground wire after the power cable is unplugged. When the option is installed, be sure to install the ground wire first and then plug in the power cable. © TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
2
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
PRECAUTIONS ■ When installing in MJ-1101
■ When installing in MJ-1106
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
3
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
■ INSTALLATION IN MJ-1101 Sub Menu
The installation procedure for MJ-1101 and MJ-6103 in the e-STUDIO2040C/2540C/3040C/3540C/4540C is the same as that for MJ-1101 and MJ-6101 in the 2820C/2830C/3520C/3530C/4520C. See the attached Web STEP “II-9. HOLE PUNCH UNIT MJ-6101” for the e-STUDIO2820C/2830C/3520C/3530C/4520C for further explanation.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
4
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
■ INSTALLATION IN MJ-1101
II-9. HOLE PUNCH UNIT MJ-6101
Sub Menu
PRECAUTIONS UNPACKING ACCESSORIES SETUP OPERATION CHECK
MJ-1101
MJ-6101
If you install the MJ-6101 Hole Punch Unit together with the MJ-1101 Finisher, you do not have to follow the procedures written in the blue boxes below.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
5
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
■ INSTALLATION IN MJ-1101
II-9. HOLE PUNCH UNIT MJ-6101
OFF
Be sure to shut down the equipment and unplug the power cable before any option is installed. The procedure for the shutdown is as follows: - Press the [ON/OFF] button until you hear a sound. - Confirm that the ON/OFF lamp is out. - Turn the power OFF with the main power switch. Be sure to install the equipment near an electric outlet so that it is easily accessible. * For Japan, remove the ground wire after the power cable is unplugged. When the option is installed, be sure to install the ground wire first and then plug in the power cable. © TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
6
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
II-9. HOLE PUNCH UNIT MJ-6101
■ INSTALLATION IN MJ-1101
UNPACKING
Sub Menu
Open the packing carton. Take out the unpacking instructions.
Take out the accessories.
Remove the packing material. Take out the Hole Punch Unit.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
7
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
II-9. HOLE PUNCH UNIT MJ-6101
■ INSTALLATION IN MJ-1101
UNPACKING
Sub Menu
Remove the 2 pieces of packing material by pulling them out.
* Be sure not to pull them out in opposite directions.
Remove other adhesive tape and packing material. © TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
8
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
II-9. HOLE PUNCH UNIT MJ-6101
■ INSTALLATION IN MJ-1101
UNPACKING
Sub Menu
Remove the screw at the front. Take off the bracket while pushing it to the left.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
9
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
II-9. HOLE PUNCH UNIT MJ-6101 HINGE BRACKET FOR BLIND COVER & SCREW (REAR)
■ INSTALLATION IN MJ-1101
ACCESSORIES
BLIND COVER (REAR)
Sub Menu
HINGE BRACKET FOR BLIND COVER & SCREW (FRONT)
BLIND COVER (FRONT)
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
10
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
II-9. HOLE PUNCH UNIT MJ-6101
■ INSTALLATION IN MJ-1101
SETUP
Sub Menu
Firstly, the procedure for when the MJ-1101 Finisher is installed is explained.
Open the front cover of the Finisher.
Take off 1 screw and then remove the lever locking bracket.
Pull the lock lever of the Finisher.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
11
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
II-9. HOLE PUNCH UNIT MJ-6101
■ INSTALLATION IN MJ-1101
SETUP
Sub Menu
Take off the connector cover. Disconnect the connector of the Finisher.
Loosen the screw. Take off the ground wire.
Separate the MJ-1101 Finisher from the e-STUDIO.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
12
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
II-9. HOLE PUNCH UNIT MJ-6101
■ INSTALLATION IN MJ-1101
SETUP
Sub Menu
Remove the screw. Take off the front feed cover from the Finisher. * The removed screw will be used again after the Hole Punch Unit is installed.
Take off 3 screws and remove the discharge brush. * 3 screws and the discharge brush that have been removed will be used again after installing the hole punch unit. © TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
13
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
II-9. HOLE PUNCH UNIT MJ-6101
■ INSTALLATION IN MJ-1101
SETUP
Sub Menu
Remove the 6 screws. * 4 of the removed screws will be used to install the Hole Punch Unit.
Lift up the lower bracket of the entrance guide to release it from the hook. Remove the lower bracket by pulling it toward you.
** The lower bracket that has been removed will be used to install the hole punch unit. © TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
14
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
II-9. HOLE PUNCH UNIT MJ-6101
■ INSTALLATION IN MJ-1101
SETUP
Sub Menu
Remove the spring from the locking lever.
Take off 2 screws and then remove the locking lever.
* The screws and the locking lever that have been removed will be used again after installing the hole punch unit.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
15
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
II-9. HOLE PUNCH UNIT MJ-6101
■ INSTALLATION IN MJ-1101
SETUP
Sub Menu
Take off 2 screws and then remove the hook bracket for the spring. Tighten the screws that have been unscrewed.
Hang the lower bracket of the entrance guide to the hook. * Use the lower bracket that has been removed in the previous step. Install the entrance guide with screws. * Use the lower bracket and 3 screws that have been removed in the previous step. © TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
16
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
II-9. HOLE PUNCH UNIT MJ-6101
■ INSTALLATION IN MJ-1101
SETUP
Sub Menu
Close the front cover. Hook the Hole Punch Unit in 2 places on the Finisher
Secure it with the 2 screws. * Use the 2 screws which were removed in the previous step.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
17
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
II-9. HOLE PUNCH UNIT MJ-6101
■ INSTALLATION IN MJ-1101
SETUP
Sub Sub Menu Menu
Secure the hook bracket for the spring with 2 screws.
Install the locking lever with 2 screws. * Use the locking lever and 2 screws that have been removed in the previous step. Mount the spring. * Use the spring that has been removed in the previous step.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
18
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
II-9. HOLE PUNCH UNIT MJ-6101
■ INSTALLATION IN MJ-1101
SETUP
Sub Menu
Secure the front feed cover at the paper feed side with the screw.
Secure the hinge bracket for the blind cover at the paper feed side at the rear of the Finisher with the screw.
Hook the blind cover in 2 places to install it.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
19
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
II-9. HOLE PUNCH UNIT MJ-6101
■ INSTALLATION IN MJ-1101
SETUP
Sub Menu
Remove the screw to take off the blind cover.
Cut out a part of the blind cover.
Connect the connector of the Hole Punch Unit to the FIN board.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
20
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
II-9. HOLE PUNCH UNIT MJ-6101
■ INSTALLATION IN MJ-1101
SETUP
Sub Menu
Secure the blind cover with the screw.
Tighten the screw together with the ground wire.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
21
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
II-9. HOLE PUNCH UNIT MJ-6101
■ INSTALLATION IN MJ-1101
SETUP
Sub Menu
Secure the hinge bracket for the blind cover at the paper feed side at the front of the Finisher with the screw.
Install the Finisher in the e-STUDIO so that the lock lever of the Hole Punch Unit fits into the hook of the finisher connecting bracket smoothly.
○
×
×
If the height of the Finisher is not aligned with that of the e-STUDIO, adjust the height of the Finisher.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
22
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
II-9. HOLE PUNCH UNIT MJ-6101
■ INSTALLATION IN MJ-1101
SETUP
Sub Menu
Lock the lever of the Finisher, and then secure it with the screw.
While fitting the positioning pin of the blind cover into the slot of the hinge bracket for the blind cover and fitting to the 2 dowels, install the blind cover in the e-STUDIO.
Connect the connector of the Finisher. Install the connector cover.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
23
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
II-9. HOLE PUNCH UNIT MJ-6101
■ INSTALLATION IN MJ-1101
OPERATION CHECK
Sub Menu
Confirm that punching is properly performed.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
24
II. UNPACKING & SET-UP
II-10. HOLE PUNCH UNIT MJ-6103
■ INSTALLATION IN MJ-1101
II-9. HOLE PUNCH UNIT MJ-6101
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
Sub Menu
25
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
Sub Menu
■ INSTALLATION IN MJ-1106
PRECAUTIONS UNPACKING ACCESSORIES SETUP OPERATION CHECK
MJ-1106
MJ-6103
If you install the MJ-6103 Hole Punch Unit together with the MJ-1106 Finisher, you do not have to follow the procedures written in the blue boxes below. © TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
26
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103 ■ INSTALLATION IN MJ-1106
OFF
Be sure to shut down the equipment and unplug the power cable before any option is installed. The procedure for the shutdown is as follows: - Press the [ON/OFF] button until you hear a sound. - Confirm that the ON/OFF lamp is out. - Turn the power OFF with the main power switch. Be sure to install the equipment near an electric outlet so that it is easily accessible. * For Japan, remove the ground wire after the power cable is unplugged. When the option is installed, be sure to install the ground wire first and then plug in the power cable.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
27
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
UNPACKING
Sub Menu
■ INSTALLATION IN MJ-1106
Open the packing carton.
Take out the accessories .
Take out the unpacking instructions.
Remove the packing material. Take out the Hole Punch Unit.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
28
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
UNPACKING
Sub Menu
■ INSTALLATION IN MJ-1106
Peel off the adhesive tape. Remove the 2 pieces of packing material by pulling them out. * Be sure not to pull them out in opposite directions.
Remove the screw at the rear. Take off the bracket.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
29
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
UNPACKING
Sub Menu
■ INSTALLATION IN MJ-1106
Remove the screw at the front. Take off the bracket while pushing it to the left.
Remove the core from the interface cable of the Hole Punch Unit.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
30
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
UNPACKING
Sub Menu
■ INSTALLATION IN MJ-1106
Remove the core from the interface cable of the Hole Punch Unit.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
31
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
ACCESSORIES
Sub Menu
■ INSTALLATION IN MJ-1106 HINGE BRACKET FOR HOLE PUNCH UNIT FRONT COVER
HINGE BRACKET FOR HOLE PUNCH UNIT REAR COVER
PUNCH PAPER GUIDE & 2 FIXING SCREWS
* Do not use the ones co-packed with MJ-6103, but those with MJ-1106.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
32
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
ACCESSORIES
Sub Menu
■ INSTALLATION IN MJ-1106
HOLE PUNCH UNIT FRONT COVER
HOLE PUNCH UNIT REAR COVER
2 BRACKET FIXING SCREWS
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
33
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
The procedure for when the MJ-1106 Finisher is installed is explained. Take off the connector cover. Disconnect the interface cable of the Finisher.
Open the front cover of the Finisher.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
34
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Remove the screw of the lock bracket to unlock it.
Separate the MJ-1106 Finisher from the e-STUDIO.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
35
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Remove the 2 temporary fixing screws from the Finisher. Reinstall the Finisher in the e-STUDIO. Lock the Finisher.
Pull out the Saddle Stitch Unit.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
36
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Secure the caster for the front side with the 2 temporary fixing screws.
Close the Saddle Stitch Unit.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
37
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Pull the lock bracket to unlock it.
Separate the MJ-1106 Finisher from the e-STUDIO.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
38
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Remove the screw. Take off the front feed cover from the Finisher.
Remove the 3 screws. * The removed screws will be used again when the plate under the entrance guide and the Hole Punch Unit paper guide are installed.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
39
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Lift up the plate under the entrance guide. Unhook the plate. Remove the plate while pulling it toward you.
* When removing the plate, do not allow its burr to be caught. * The removed screws and plate will be reinstalled in a later step. © TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
40
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Move the lock guide to the locking position. Remove the 2 screws. Take off the lock bracket.
* The removed screws and lock bracket will be used again to install the Hole Punch Unit.
Remove the screw. Take off the rear positioning guide.
* The removed screw and guide will be used to install the Hole Punch Unit. © TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
41
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Remove the 2 screws. Take off the front positioning guide.
* The removed screws and guide will be used to install the Hole Punch Unit. Hook the plate under the entrance guide in 2 places. Secure the plate with the screw.
* Use the screw which was removed in the previous step. © TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
42
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Install the punch paper guide with the 2 screws.
* Use the 2 screws (M3 x 8) co-packed with MJ-1106. * Install the paper guide by inserting it to the paper feed inlet of the Finisher slantwise from the front. © TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
43
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Close the front cover.
Install the Hole Punch Unit by hooking it to the Finisher in 2 places.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
44
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Secure the unit with the 2 screws.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
45
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
nstall the rear positioning guide with the screw.
* Use the screw and the rear positioning guide which were removed in the previous step.
Install the front positioning guide with the 2 screws.
* Use the screws and the front positioning guide which were removed in the previous step. © TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
46
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Install the lock bracket with the 2 screws.
* Use the screws and the lock bracket which were removed in the previous step. * Be careful not to tighten the screws too much, otherwise the lock bracket will not be able to move.
Install the Finisher front feed cover with the screw.
* Use the screw and the cover which were © TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
47
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Open the front cover. Pull out the Saddle Stitch Unit.
Remove the screw. Take off the blind cover on the lower side of the Finisher at the rear.
Install the hinge bracket for the Hole Punch Unit rear cover with the screw.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
48
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Install the Hole Punch Unit rear cover by hooking the 2 lower hooks and setting the 2 upper hooks.
Install the blind cover on the lower side of the Finisher at the rear with the screw.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
49
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Install the hinge bracket for the Hole Punch Unit front cover with the screw.
Remove the 2 temporary fixing screws for the casters on the Finisher front feed side.
Temporarily tighten the removed screws.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
50
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Close the Saddle Stitch Unit and then the front cover.
Remove the 2 screws. Take off the blind cover on the upper side of the Finisher at the rear.
Cut out a part of the blind cover.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
51
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Connect the connector of the Hole Punch Unit to the FIN board.
Install the blind cover with the 2 screws.
* When installing the cover, make sure not to allow the harness to be caught. © TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
52
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Pull out the lock bracket.
Move the Finisher closer to the e-STUDIO carefully until the guide pin of the Finisher connecting bracket of the e-STUDIO and the positioning hole of the Hole Punch Unit are aligned. Set the Finisher to the e-STUDIO.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
53
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Push the lock bracket in and then secure it with the screw.
Make sure that the gap between the Hole Punch Unit and the e-STUDIO front side is in the range of 0 to 10 mm. 10mm
0～10mm
If the gap exceeds 10 mm, perform gap adjustment for the Finisher. (Refer to “II-9. UNPACKING AND SETUP FOR FINISHER MJ-1106”.)
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
54
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
SETUP
Sub Menu
■ INSTALLATION IN MJ-1106
Hang the hook on the hinge bracket for the Hole Punch Unit front cover in one place to install the cover.
Connect the interface cable of the Finisher to the e-STUDIO.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
55
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
OPERATION CHECK
Sub Menu
■ INSTALLATION IN MJ-1106
Confirm that punching is properly performed.
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
56
II. UNPACKING & SET-UP II-10. HOLE PUNCH UNIT MJ-6103
Sub Menu
■ INSTALLATION IN MJ-1106
Main Menu
Menu
Next Chapter
© TOSHIBA TEC CORPORATION 2011 All Rights Reserved.
57
