Transcript
Connectivity & Drop Components
F-001
Series
PermaSeal-II™ F Series Compression Connectors
Single-piece elegant design simplifies installation and reduces assembly time
A Steren Registered Trademark
Triple environment seal protection prevents (cable-to-connector interface) water migration providing failsafe protection
COMPLIANT
Ridge-patterned internal sleeve
Internal Neoprene O-Ring and UVstabilized external ring prevents water migration through the connector collar ensuring reliability and high performance Unique ridge-patterned internal sleeve presses connector securely against cable jacket providing positive mechanical restraint and permanent moisture migration seal
UV-stabilized external ring
Internal Neoprene O-Ring
Precision Machined High-Grade CDA360 Brass
Triple Environmental Seal Protection
Precision machined high-grade CDA360 brass construction, nickel or cadmium plated for maximum corrosion resistance 70-lbs pull-out strength exceeds SCTE cable retention standard IPS-SP-405 Impressive –30dB return loss typical up to 3GHz and less than –0.20dB insertion loss typical to 3GHz provides unsurpassed performance Higher than 96dB RFI shielding provided through true 360° internal radial compression Color-coded collar rings allow easy cable size identification Oversize easy-grip 7mm wide 7/16˝ hex free-spinning nut allows easy installation Quick 1/4˝-1/4˝ standard cable preparation allows use with TruSpec™ PFC-001 or most other manufacturer’s compression tools
www.picomacom.com
Oversize Easy-Grip 7mm Nut
F-001
Series
PermaSeal-II™ F Series Compression Connectors The PermaSeal-II™ F-001 Series is Pico Macom’s high-grade compression connector designed for use with standard, tri-shield, or quad-shield SCTE specification 59, 6, and 11 series cable. The patented true 360° internal compression design allows excellent RFI shielding properties while maintaining an impressive –30dB return loss to 3GHz. The PermaSeal-II™ provides triple protection against moisture migration ensuring high reliability and consistent performance. The internal O-Ring and UVstabilized external ring fully seal the connector collar while a unique ridge-patterned internal sleeve presses firmly against the cable jacket sealing the connector against moisture at the back end. This same internal sleeve also provides over 70-lbs pulling strength, exceeding SCTE’s cable retention standards without damage to the cable’s outer jacket. PermaSeal-II™’s connector body is constructed of precision machined brass and nickel or cadmium coated providing superior resistance to corrosion. Its industry standard length allows use with TruSpec™ PFC-001 compression tool or most commercially available tools, making installation fast and reliable. Each connector is easily color-identified for cable size.
355 Parkside Drive San Fernando, CA 91340 Ph: 818-493-4300 Toll Free: 800-421-6511 Fax: 818-493-4433
D-1 Rev. 12/02
Product Specifications
F-001
Series
PermaSeal-II ™ F Series Compression Connectors
33/8" /8˝ 32UNF 32UNF
5.5 4.8
8.0
11.0
Figure A
C
BA
Figure B
7.5
16.1 29.75
Specifications Nut: Internal O-Ring: External O-Ring: Color Band: Body: Center Ring: Compression Ring: Outer Body: Frequency range: Impedance: Return Loss: Insertion Loss: Crimp Tool:
CDA360 Brass Rubber Neoprene Nylon UV-Stabilized PVC CDA360 Brass CDA360 Brass Nylon CDA360 Brass 0-3 GHz 75 Ohms >-30 dB @ 1 GHz 0.1 dB @ 1 GHz 0.3 dB @ 3 GHz TruSpec™ PFC-001
RETURN LOSS Typical 1:Off 2:Reflection
Log Mag
10.0 db/ RF
db 10
Meas2:
0.00
db
C
Mkr8 3000.000 Mhz -37.150 db
2: -10 -20 -30 -40 -50 -60 -70 Start 0.300 Mhz
Stop 3000.000 Mhz
Ordering Information F56-001
RG6 PermaSeal-II ™ Yellow Band A
F56Q-001
RG6-Quad PermaSeal-II ™ Blue Band
F59-001 F11-001
D-2
Figure
4.8
5.5
8.0
RG59 PermaSeal-II ™ Red Band
4.8
5.5
8.5
A
8.2
7.3
11.3
B
RG11 PermaSeal-II ™
3.9
4.6
7.0
A
Specifications Subject to Change
Rev. 12/02
Dimensions (mm) B C
A
© Copyright 2003 Pico Macom, Inc.
355 Parkside Drive San Fernando, CA 91340 Ph: 818-493-4300 Toll Free: 800-421-6511 Fax: 818-493-4433
www.picomacom.com
