Transcript
If you require any advice or assistance regarding your Sharp product, please visit our web-site www.sharp.co.uk/support Customers without internet access may telephone 0845 880 0512 during office hours (or (01) 676 0648 if telephoning from Ireland).
MODEL
HT-SB35D SOUND BAR HOME THEATRE SYSTEM
This Quick Start Guide will help you to correctly install and operate your system.
Accessories Accessories ON/ -BY STAND NEWS DE D MO SOUNMUSIC INPUT A OUND SURR SS TV BYPA
MUTE
Before using remote control System connection Beforesure usingto remote control, remove plastic Make unplug the please AC power lead before shield at battery holder. making any connections.
CINEM
CH
VOL
VOL
AWSA
GA369
RRMC
Remote control x 1× 1 Remote control (RRMCGA369AW01)
AC/DC RCAadaptor cable x 2 (RADPAA100AWZZ) (2 pins - 2 pins) × 1
1 Plug the AC power lead into the AC/DC adaptor. shield 2 Plug the AC/DC adaptor cable Plastic into the DC INPUT socket on the sound bar. Remote control 3 Plug the AC power lead into a wall socket. The Subwoofer Pairing indicator turns blue.
Optical cable x 1
Battery holder
Pattern paper x 1
AC power lead × 1
Foot cushion × 4
AC/DC Adaptor Cable
2
Turn on your system
Velcro tape (hook type) x 1
AC/DC adaptor × 1
Velcro tape (loop type) x 2
Wall mount angle × 2
Nut AC power lead x 2
HT-SB35D
NFC tag x 1
(Spike + Nut) × 4 (Length: 25 mm)
Pattern paper × 1
DC IN socket (DC 19V) 1 Press the ON/STAND-BY button. The sound mode indicator and display light up. If the power does not turn on, check whether the power AC powerinlead Wall socket cord is plugged properly. 1 2 To set the unit to stand-by mode: AC/DC Adaptoragain. Press the ON/STAND-BY button (AC 100 - 240red. V The STAND-BY indicator turns ~ 50/60 Hz)
Spike leg x 2
Remote control battery installation using remote control codesoft Before
Before using the remote control, remove the /www.barcodesoft.com 1 Insertshield pin intofrom the hole shownholder. and pull to open the plastic theas battery battery holder.
Remote control
Plastic shield
ode Symbology: Code 93; Font Facename: Code93M Pin To Encode: TINSEA494AWZZ Back of remote control
Size 8 :
Battery holder
*TINSEA494AWZZUT*|
Size 10 :
*TINSEA494AWZZUT*|
HTSB35D_A4_QG.indd 1
2 Remove the old battery from the 2battery holder,
insert the new battery and then slide the battery thelead remote control. power Wallholder socket backACinto Battery holder AC/DC Adaptor 1 Positive (+) side up Cable Battery type AC/DC Adaptor (AC 100 - 240 V Locking tab ~ 50/60 Hz) Polarity (+) symbol
Printed in Malaysia 1 14M11A R RKIAS1
TINSEA348AWZZ TINSEA494AWZZ
Size 12 : HT-SB250W250BK (QG).indd
DC IN socket (DC 19V)
1
12/29/2010 5:07:22 PM 2014-11-28 08:20:24
Sound bar connections to TVs Caution: Turn off all other equipment before making any connections. Notes: ●● To connect to TV/player, use AUDIO IN or OPTICAL IN terminals located at the rear of the sound bar. ●● Refer the operation manual of the equipment to be connected. ●● Fully insert the plugs to avoid fuzzy pictures or noises. ●● If the TV volume is continuously at low level, the sound bar will automatically power off. Increase the TV output volume to enjoy the sound from the speaker. ●● To avoid desynchronized audio and video when using an external player, connect the output signal from the player to TV and the audio output (from TV) to the sound bar.
■■ Connecting a TV, or DVD player, etc. If the TV/monitor has an audio or optical output, connect it to the AUDIO IN socket or OPTICAL IN socket on the rear of the sound bar. Press the INPUT button repeatedly to select: Function OPTICAL IN AUDIO IN Bluetooth TV
On/Standby/Input/Bluetooth Pairing Indicator Turns green Turns cyan Turns blue To audio output terminals Audio cable
Blu-Ray/DVD player/Digital Tuner
Audio signal
or
To optical digital audio output terminal
Optical digital audio cable (supplied)
Optical digital audio cable
Sound bar
To OPTICAL IN (optical) input terminal
To AUDIO IN input terminal Audio cable (commercially available)
Connecting the wireless Subwoofer
Turn on your system
The sound bar and subwoofer will link automatically (wirelessly) when turned on as it is already pre-linked at the factory. If the link cannot be established, please set the connection by the following method. ●● During pairing process: Subwoofer Pairing indicator will blink. ●● When pairing is successful: Subwoofer Pairing indicator lights up. During sound bar standby and subwoofer power off mode (AC power lead unplugged): 1. Press and hold the PAIRING button on the sound bar or SW LINK button on the remote control for more than 3 seconds. Subwoofer Pairing indicator will blink. 2. Within 3 minutes, plug in the AC power lead of the subwoofer and turn it on. Subwoofer pairing indicator will light up. ●● In case the link is still not established (Subwoofer Pairing indicator blinks), press and hold the SW LINK button at the back of the subwoofer until Subwoofer Pairing indicator lights up.
Press the ON/STANDBY button. The On/Standby/Input/Bluetooth Pairing indicator lights up according to input source: Input source Indicator OPTICAL IN
Turns green
AUDIO IN
Turns cyan
Bluetooth Turns blue Note: If the power does not turn on, check whether the power lead is plugged in properly. To set the sound bar to standby mode: Press the ON/STANDBY button again. The Subwoofer Pairing indicator lights up.
SW LINK
Sound bar
HTSB35D_A4_QG.indd 2
Remote control
Subwoofer
2014-11-28 08:20:25
