Transcript
Rev 0 – March 2013
Key Digital®, led by digital video pioneer Mike Tsinberg, develops and manufactures high quality, cutting-edge technology solutions for virtually all applications where high quality video imaging is important. Key Digital® is at the forefront of the video industry for Home Theater Retailers, Custom Installers, System Integrators, Broadcasters, Manufacturers, and Consumers.
Key Digital® Systems :: 521 East 3rd Street :: Mount Vernon, NY 10553 Phone : 914.667.9700
Fax : 914.668.8666
Web : www.keydigital.com
Phantom Series™ HDMI Switchers with Audio De-Embedder, Coaxial Audio, Optical Digital Audio & Analog L/R
Operating Instructions KD-HDSW2x1Pro
KD-HDSW3x1Pro
KD-HDSW4x1Pro
The Experts in Digital Video Technology and Solutions™
4
Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick Setup Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 DVI Applications for KD-HDSW Pro Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 IR Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Serial IR & IR Emitter Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 EDID Control Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 External Audio Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 RS-232 Commands and Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Using iAS Intelligent Auto Sense™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Important Product Warnings & Safety Instructions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 How to Contact Key Digital® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Always follow the instructions provided in this Operating Manual. © 2013 Key Digital, Inc. All rights reserved.
1
Introduction Key Digital® Phantom Series™ HDMI/DVI switchers are designed and engineered to offer the best in quality, performance, and reliability while providing a cost effective HDMI/DVI switching solution. Phantom Series™ HDMI switchers are a transparent solution for all digital video/audio switching applications and support all HD and SD video standards, including 1080p/60. In addition, the KD-HDSW line has complete support for the latest 3D technology. KD-HDSWPro switchers feature iAS™ Intelligent Auto Sense signal detection and switching, pushbutton control, IR, RS-232, status-monitoring LEDs, and support for HDMI CEC. The Phantom Series™ switchers support multiple unit expandability, and are individually addressable. About the KD-HDSW2x1Pro; KD-HDSW3x1Pro; KD-HDSW4x1Pro ›› Digital switching of multiple (2, 3, or 4) HDMI inputs to one (1) HDMI output ›› Supports all SD, HD, and VESA (VGA, SVGA, XGA, WXGA, SXGA, UXGA) resolutions up to
›› ›› ›› ›› ›› ›› ›› ›› ›› ››
1080p (60Hz & 50Hz) »» SD & HD: 480i, 480p, 720p, 1080i, 1080p »» VESA: From 640x480p up to 1920x1200p EDID Control featuring 12 internal library settings or auto EDID detection from display EDID and HDCP Transparency between sources and display Can de-embed audio from the HDMI input and send it to external digital or analog audio outputs Supports signal rates up to 10.2 Gb per second Supports HDMI and DVI-D Supports CEC Compliant with all HDMI® versions and HDCP copyright protection Input and Output status indicated by LED lights Firmware upgradable Rack mountable
Advanced HDMI® Features ›› 3D – Capability to pass 3D stereoscopic signal formats
Accessories ›› ›› ›› ›› ››
External power supply: 5V 2A HDMI Lacing Clips Rack Ears Operating Instructions Warranty Card
HDMI/DVI*
Satellite Box
2
KD-HDSW4x1Pro
Serial IR
HDMI/DVI*
HD
Optical IR
Cable Box
Quick Setup Guide
RS-232
IR ›› Step 1: Find a safe and convenient location toOptical mount or place your KD-HDSW unit HDMI/DVI ›› Step 2: Begin with the KD-HDSW unit and all input/output devices turned off with power cables *
DVD Player
›› ›› ›› Blu-Ray ›› ›› ››
Step 3: Step 4: Step 5: Step 6: Step 7: Step 8:
removed EDID Control Connect your HDMI or DVI-D source devices to the input ports of your KD-HDSW unit Audio Rcvr. Connect your HDMI or DVI-D display to the output port of your KD-HDSW unit Audio HDMI/DVI Connect the desired IR or RS-232 control inputs to your HDMI/DVI KD-HDSW unit Audio Be sure the Operation Mode Switch is set to the “Normal” position *To connect DVI, use HDMI to DVI adapters Connect power to the KD-HDSW unit Power on input/output devices *
Satellite Box HDMI/DVI*
Cable Box
KD-HDSW4x1Pro
HDMI/DVI*
Serial IR Optical IR RS-232
DVD Player
Optical IR HDMI/DVI*
EDID Control
Blu-Ray HDMI/DVI*
Audio Rcvr. Plasma TV
Audio HDMI/DVI*
Audio
Audio
Audio
HDMI/DVI Audio
*To connect DVI, use HDMI to DVI adapters
Speakers
Sub-Woofer
Speakers
Note: N o signal conversion is done on the KD-HDSW2x1Pro; KD-HDSW3x1Pro; KD-HDSW4x1Pro. If input Desktop PC signal is HDMI output signal will be HDMI. If input signal is DVI output signal will be DVI. DVI Video*
KD-HDSW4x1Pro Laptop
DVI Video*
Serial IR Optical IR RS-232
HDMI/DVI*
DVD Player
EDID Control
3 Audio
Audio Rcvr. Audio
HDMI/DVI
HDMI/DVI
*
Speakers Audio
Audio
Blu-Ray
*To connect DVI, use HDMI to DVI adapters
Installation and Operation Before permanently securing the unit for final installation of cabling behind walls or ceilings, test for Satellite Box proper operation of the unit and the cables in your system. It is recommended that you leave enough ventilation space to provide sufficient airflow and cooling, especially if leaving the unit powered at all times. HDMI/DVI*
Box AnCable optional HDMI cable clip (included) allows for a secure HDMI cable connection to be made to KD-HDSW4x1Pro the rear of the unit and helps defeat intermittent or completeSerialsignal loss due to poor connection. IR HDMI/DVI*
Optical IR
Active Input / Output LED Indicators
RS-232
DVD Player
Opticalvia IR Your KD-HDSW unit may be controlled the pushbutton on the front of the unit. Select your desired input by depressing the “Input Select” button. The front LED indicators (1, 2, 3, 4) correspond to the selected input. EDID Control HDMI/DVI*
Blu-Ray HDMI/DVI*
Audio Rcvr. Plasma TV
Audio HDMI/DVI*
Audio
HDMI/DVI
Audio
Audio
DVI Applications for KD-HDSW Pro Series Audio
KD-HDSW Pro Distribution Amplifiers can also be used with DVI-D sources and displays. For *To connect DVI, use HDMI to DVI adapters these applications, use DVI to HDMI adapters. Note that while HDMI supports both video and audio over an HDMI cable, DVI-D supports only video. Speakers
Sub-Woofer
Speakers
Desktop PC DVI Video*
KD-HDSW4x1Pro Laptop
DVI Video*
Serial IR
Plasma TV
Optical IR RS-232 DVI Video*
Optical IR
Desktop PC
DVI Video*
EDID Control DVI
Laptop
DVI Video*
*To connect DVI, use HDMI to DVI adapters
Sub-Woofer
4
IR Remote Control The KD-HDSW can also be operated using the IR remote control provided with your unit. The KD-HDSW switcher features IR sensors on the front and rear of the unit for reception of the IR signals. Power On
Power Off Power On
Power Off
Input Select www.keydigital.com
Input
Auto Input Select
1
Input Select Scroll Down
3
4
Auto
Input Select Scroll Up R1, R2, R3
Numeric Keypad Used in addressable mode for specifying unit’s address
2
Reserved for future use
Device Select
1
2
3
R1
4
5
6
R2
7
8
9
R3
0
Serial IR & IR Emitter Control ›› The “Serial IR” port requires the use of a Male 3.5mm Mono cable (not included) with the IR
command signal being carried on the “Tip” of the input inserted into the KD-HDSW unit. The location of the IR signal may vary by control system used. Please verify the location of the IR signal with your control system. Ground
Signal
›› When using the IR Emitter / IR Extender (sold separately), the
IR Emitter must be mounted over the IR Sensor on the KDHDSW unit. It is recommended that the rear IR sensor of the KD-HDSW unit be utilized for these applications. One end of the cable is connected to the IR Receiver / Master Controller / IR Extender / IR Connecting Block, while the other end is mounted over the IR Sensor of the KD-HDSW unit.
5
EDID Control Settings At times, your HDMI sources and display may not synchronize properly. This is when EDID* control should be utilized. KD-HDSW Pro Switchers feature an internal library of EDID settings to ensure your HDMI source’s output is compatible with the display devices. Please reset the unit by either unplugging and plugging the HDMI connections, or via a power cycle for the new settings to take effect.
Rotary EDID Settings (Default EDID: 0): KD-HDSW2x1Pro EDID Settings
KD-HDSW3x1Pro EDID Settings
Rotary EDID Control Switch
KD-HDSW4x1Pro EDID Settings
0
Copy EDID from HDMI Output
0
Copy EDID from HDMI Output
0
Copy EDID from HDMI Output
1
1080i, 2Ch Audio
1
1080i, 2Ch Audio
1
1080i, 2Ch Audio
2
1080i, Dolby/DTS 5.1
2
1080i, Dolby/DTS 5.1
2
1080i, Dolby/DTS 5.1
3
1080i, HD Audio
3
1080i, HD Audio
3
1080i, HD Audio
4
1080p, 2ch Audio
4
1080p, 2ch Audio
4
1080p, 2ch Audio
5
1080p, Dolby/DTS 5.1
5
1080p, Dolby/DTS 5.1
5
1080p, Dolby/DTS 5.1
6
1080p, HD Audio
6
1080p, HD Audio
6
1080p, HD Audio
7
3D, 2ch Audio
7
3D, 2ch Audio
7
3D, 2ch Audio
8
3D, Dolby/DTS 5.1
8
3D, Dolby/DTS 5.1
8
3D, Dolby/DTS 5.1
9
3D, HD Audio
9
3D, HD Audio
9
3D, HD Audio
A
1280x1024 DVI
A
1280x1024 DVI
A
1280x1024 DVI
B
1920x1080 DVI
B
1920x1080 DVI
B
1920x1080 DVI
C
1920x1200 DVI
C
1920x1200 DVI
C
1920x1200 DVI
D
1080p, 2Ch Audio
D
1080p, 2Ch Audio
D
1080p, 2Ch Audio
E
1080p, 2Ch Audio
E
1080p, 2Ch Audio
E
1080p, 2Ch Audio
F
1080p, 2Ch Audio
F
1080p, 2Ch Audio
F
1080p, 2Ch Audio
Example of EDID Auto Select: If one of your system’s displays supports 1080p and the second display only supports up to 1080i (does not support 1080p), then the highest common EDID format supported is 1080i. By choosing the Auto Select EDID Setting, your KD-HDSW Pro unit will inform your source device to output 1080i in order to ensure all displays receive a supported signal.
*EDID (Extended display identification data) is a data structure provided by a display to describe its capabilities to a source device.
6
External Audio Outputs Analog audio output via 3.5mm stereo phone jack ›› 2 channel analog audio output from the selected HDMI
input source ›› Converts only 2 ch. PCM audio from the HDMI input to
2 channel analog audio output ›› Only supports 2 ch. PCM audio, not multi-channel PCM,
Dolby, DTS, HD audio Digital audio output via Coax/RCA ›› Digital audio output from the selected HDMI input source ›› Uses SPDIF format ›› Supports 2 ch. PCM, Dolby, DTS; does not support multi-channel PCM or HD audio Digital audio output via Optical ›› Digital optical audio output from the HDMI input ›› Uses SPDIF format ›› Supports 2 ch. PCM, Dolby, DTS; does not support multi-channel PCM or HD audio
RS-232 Commands and Protocol ›› KD-HDSW Pro units are compatible with all Control Systems, such as Compass Control®, AMX®,
Control4®, Crestron®, RTI®, Universal® ›› Connect your Control System’s Master Controller to the KD-HDSW Pro unit using the RS-232 port. Follow all instructions provided with your control system. ›› RS-232 Protocol: ›› All RS-232 commands must be in »» Baud Rate = 57600 bits per second lower case letters »» Data Bits = 8 / Stop Bits = 1 ›› Command must be terminated with »» Parity = None a carriage return »» Flow Control = None RS-232 Command
Description
Azz
All Commands may have Prefix System Address zz=[01-99]
H
Help
PF
Power Off
PN
Power ON
STA
Show Global System Status
Video Output Setup Commands: yy = [01-04] (A=All) SPO SIyy
Set Output to Video Input yy
SPO ON/OFF
Set Output ON/OFF
Audio Output Setup Commands: [E=Enable, D=Disable] SPO AA E/D
Enable/Disable External Analog Audio Output
SPO DA E/D
Enable/Disable External Digital Audio Output
7
System Address Setup Command: xx = [00-99], 00 = Single SPC Axx
Set System Address to xx
System Control Setup Commands: SPC AS ON/OFF
Set Auto Sensing Mode ON/OFF
SPC FB E/D
Enable/Disable Front Panel Buttons
SPC DF
Reset to Factory Defaults
Using iAS Intelligent Auto Sense™ Intelligent Auto Sense (iAS™) automatically switch inputs when Hot Plug Detect signal becomes active on an input. iAS™ can be enabled and disabled via IR or RS-232 control. Please note that many common HDMI sources, such as a cable or satellite boxes, will emit Hot Plug Detect signals when in stand-by mode and may prevent full functionality of iAS™. When the blue “Auto” button on the IR remote is pressed or the ‘SPC AS ON’ RS-232 command is sent, iAS will be activated on the KD-HDSW Pro unit.
Specifications Inputs
4/3/2 HDMI Connectors
Outputs
1 HDMI Connector
Bandwidth
TMDS bandwidth 10.2 Gb/s
HDMI Compliance
All HDMI Versions and HDCP.
Link
Single Link: 1080p/60, 12 bit color depth, 1920x1200 max.
Deep Color Support
Digital video formats in Deep Color Mode at up to 12 bits/color
Lossless Compressed Digital Audio
Dolby® TrueHD, Dolby® Digital Plus and DTS™-HD Master Audio
DDC Signal (Data)
Input DDC Signal: 5 Volts p-p (TTL)
HDMI Video/Audio Signal
Input Video Signal: 1.2 Volts p-p
HDMI Connector
HDMI Connector: Type A, 19 Pin Female
I2C Communication
EDID and HDCP Bi-Directional Transparency from Display to Source
EDID Control
Active outputs connected via HDMI, or from internal library of default 12 EDID settings
Control
For RS-232 Db9 Female connector for Tx, Rx and ground. For IR two optical windows and wired 3.5 mm female mini-stereo connector. Push button and top LED’s.
®
Power Source
5 Volt DC @ 2 Amp, 100-240 VAC, 50-60 Hz
Dimensions
W=8.5”, H=1.75”, D=4”
Weight
2 Lbs
8
Important Product Warnings: 1. Connect all cables before providing power to the unit. 2. Test for proper operation before securing unit behind walls or in hard to access spaces. 3. If installing the unit into wall or mounting bracket into sheet-rock, provide proper screw support with bolts or sheet-rock anchors.
Safety Instructions: Please be sure to follow these instructions for safe operation of your unit. 1. Read and follow all instructions. 2. Heed all warnings. 3. Do not use this device near water. 4. Clean only with dry cloth. 5. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 7. Only use attachments/accessories specified by the manufacturer. 8. Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged in any way including: »» Damage to the power supply or power plug »» Exposure to rain or moisture
Power Supply Use: You MUST use the Power Supply provided with your unit or you VOID the Key Digital® Warranty and risk damage to your unit and associated equipment.
9
How to Contact Key Digital® System Design Group (SDG) For system design questions please contact us at: ›› Phone: 914-667-9700 ›› E-mail:
[email protected]
Key Digital Trainings For questions about Key Digital® Trainings please contact us at: ›› Phone: 914-667-9700 ›› E-mail:
[email protected]
Customer Support For customer support questions please contact us at: ›› Phone: 914-667-9700 ›› E-mail:
[email protected]
Technical Support For technical questions about using Key Digital® products, please contact us at: ›› Phone: 914-667-9700 ›› E-mail:
[email protected]
Marketing and Public Relations: For marketing and public relations information, please contact us at: ›› Phone: 914-667-9700 ›› E-mail:
[email protected]
Repairs and Warranty Service Should your product require warranty service or repair, please obtain a Key Digital® Return Material Authorization (RMA) number by contacting us at: ›› Phone: 914-667-9700 ›› E-mail:
[email protected]
Feedback Please email any comments/questions about the manual to: ›› E-mail:
[email protected]
Warranty Information All Key Digital® products are built to high manufacturing standards and should provide years of trouble-free operation. They are backed by a limited three-year parts and labor warranty.
