Transcript
QUICKSTART “BASIC” GUIDELINES FOR MODEL 9000 - FRONT INSTALLATION MOUNTED ON A CONCRETE PAD “FULL OPEN” ON
Adjust the 2 limit nuts by depressing the lock plate and spin nuts to desired open and closed gate positions. After adjusting, make sure the lock-plate is engaged in the slots on the limit-nuts to prevent them from rotating.
3
7
e ir W 3-
Ra
Note: Partial Open Feature is optional and not used for a fully opening gate, see manual for more information.
dio
Re
#
8
cei
*
ver
ain
kP
9
5 4
Ch
Loc
6
2 1
Par
0
tial
1 2 3 4 5 6 7 8
Adjustment of Limit Switches Bra
SW
cke
late
1 itch Sw FF in Oition. s po
ng eni Op ction e Dir
1
t
Op
en
C
Model 9000 is intended for installation only on sliding gates used for vehicles.
120 Glasgow Avenue Inglewood, California 90301
Pedestrians must be supplied with a separate access opening. For complete safety, installation and adjustment of operator instructions, please refer to the Series 9000 Installation/Owner’s manual.
U.S.A.
High Voltage Connection GATE OPERATOR MUST BE PROPERLY GROUNDED!! Tip: It is recommended that a surge suppressor be installed on the input high voltage power line.
Chain Adjustment M CO it m Li
Adjust the chain nuts to tighten the chain. The chain should sag no more than one (1) inch per 10 feet of chain travel. Do not over tighten the chain.
Typical Single Operator Settings
B
D
SW 1
Po
ON 1 2 3 4 5 6 7 8
itc Sw N O in ition. pos
E AT ly ER on OP use TO an SH nici PU tech
Ma
t Cenition s o P
Reset
nu al
Re
1. OFF 2. OFF 3. ON 4. OFF
1 23 Adjust 1 to 23 sec.
HIGH VOLTAGE
208/230/460 VAC Single Phase
Chain, Conduit Area and Concrete
lea
se
A
it
du
n co ch in s. 4- p 3/ ee se sw U ith w
p Loonduit o C
r
we Po it C A ndu Co
Two 115 VAC Convenience Outlets For access control and safety device AC power.
L2
24”
m tto Bo ition s Po
Co n MU crete ST pa be d lev el!
L1
DANGER
HIGH VOLTAGE
1
ng eni n Op ectio Dir
Input Power Line: White - Neutral Black - 115 VAC Hot Green - Chassis Ground
Chassis Ground
SW 2
ors
nch
eA
Co nc ret Pae d
um v im und. lee n S i m ro 2” 4”ove g ”x 8 / . 3 d) is ng ab 4) e ( plie pad uildi Us t sup e t re al b (No onc d loc ded). c the an en of tions omm h t i c dep cond te re d l e n i r u o c gro by s con ow ined rced l e B rm nfo i e det es (re d co Copyright 2010 DoorKing, Inc. All rights reserved.
4” minimum space between the gate and operator chassis.
4”
Chassis Ground
Operator Chassis
3.5” Gate
SW
eel Whition r e Idl Pos Top er
h1
1 2 3 4
operator until the “DIP-Switches” and the “Limit Switches” have been adjusted. Damage could occur to the gate and operator.
r we
ON
DO NOT power up and cycle the
DANGER
1. Opening Direction (See Illustration) 2. OFF 3. ON Auto-Close Timer 4. ON TIME 5. OFF DELAY 6. OFF E 7. OFF 8. OFF
Hot
A
r Idleeel h W
ON
E
B
1 2 3 4 5 6 7 8
Chain brackets MUST be mounted so the chain remains the same height as it is on the idler wheels!
A
Hot
N or ot M
D
Hot
e ar it m Li C VA 24
tr eu
al
DIP-Switches
or ot M
1
Sp
5 4 3 2
Neutral
115 VAC 8 7 6
13.5” Center of concrete pad
4.5” Conduit Area
Concrete Pad Operator and chain MUST be parallel to gate!
24”
Use two legs of incoming 3-phase input power line.
Loop Detectors B Not included - Refer to the Installation/Owner’s manual for more information about DoorKing’s Plug-In loop detectors. DoorKing highly recommends that loops and loop detectors are installed with this slide gate operator. DoorKing offers a free “Loop and Loop-Detectors Information Manual” PDF located at DoorKing’s web site for more information. www.dkaccess.com
Radio Receiver C Not included - Refer to a specific Radio Receiver
Chain bracket MUST line up with chain idler wheels!
Manual (available from www.dkaccess.com) for more information on radio receivers and antenna installation. 9000-066-D-1-10
