Manual 20129182

Transcript

4.LED indicators, Wires, Auxiliary Input and Output Four-door Installation Guide Vision: 1 . 0 . 1 Notes: Date: Oct. 2010 1.Cautions Please note the following cautions.Mis-operation may lead to personal injury or equipment failure: 1） Do not energize the system before installation is complete; never carry out installation activities when the system is energized. 1)Meaning of LED indicators: LINK indicator(green): always(green) indicates TCP/IP communication is proper; ACT indicator(yellow):its flashing indicates data is in transmitting through TCP/IP communication. TX indicator(yellow):its flashing indicates it is sending data through RS485 communication. RX indicator(green):its flashing indicates it is receiving data through RS485 communication. Auxiliary output indicator(green):always(green) indicates it is in use. Lock indicator(green):always(green) indicates lock is open. POWER indicator(red):always(red) indicates control panel is power on. RUN indicator(green):its flashing indicates the system works normally. CARD indicator(yellow):its flashing indicates card is punched on reader. 2)Recommended use of wires： A Use 2-conducotor power cord B Use 6-conductor wire between wiegand reader and control panal (RVVP 6*0.5mm) (To choose the proper cord according to the interface you connect, such as 6,8,10 cord.) C Use 4-conducotor lock power cord (RVV 4*0.75mm) D Use 2-conducotor switch power cord（RVV 2*0.5mm) 3)The auxiliary input may be connnected to infrared body detectors, alam switches,etc. 4)The auxiliary output may be connected to door bells,alarms,etc. 2） All peripheral devices must be grounded. SD Card Ethernet interface GND 485485+ IN BUTTON1 TX RX +12V EXT PC PC RS485 interface (green) flashes. 485+ 485GND IN GND AUX4 Advanced Access Control Connect the system to the power supply.If the system works properly,the POWER indicator(red) is lit constantly and the RUN indicator GND AUX3 Description of normal working state: IN ACT 5 6 7 8 Dip switch ON 6） It is recommended to use the power supply in case for control panel, and external power supply for each lock. 1 2 3 4 5） It is recommended that card readers and buttons should be installed at height of 1.4m-1.5m above ground. AUX2 IN GND D Auxiliary input1 D Auxiliary input2 D Auxiliary input3 D Auxiliary input4 { LAN clamping tools may be used to avoid unintentional contact of exposed wires to avoid short-circuit or communication failure. AUX1 IN GND 4） It is strongly recommended that the length of exposed part of any connection cable should not be longer than 4 mm. Professional { { { { LINK 3） It is preferred that all wires run through PVC or galvanized pipes. Extended RS485 output TX RX GND RUN CARD D 2# Door Button B 2# Door wiegand reader D 3# Door Button B 3# Door wiegand reader { +12V B 1# Door wiegand reader { POWER +12V D 1# Door Button { Power of control panel WD1 WD0 GND READER4 Fixed case A IN GND BUTTON4 Get through the thread hole 2 V+ V- READER3 1 LOCK POWER A Power of lock BEEP GLED WD1 WD0 GND +12V BEEP GLED 1 C Door4 SEN GND NO COM NC 1 C Door3 SEN GND NO COM NC LOCK4 Thread hole IN GND BUTTON3 3.Get through the thread hole GND +12V 1 C Door2 SEN GND NO COM NC LOCK3 { { { { BEEP GLED WD1 WD0 READER2 C Door1 SEN GND NO COM NC 1 Appearance of case IN GND { { { { Thread hole NO COM NC BUTTON2 Auxiliary output4 BEEP GLED WD1 WD0 GND +12V { D Heat dissipation hole GND READER1 Auxiliary output3 NO COM NC LOCK2 D LOCK1 Auxiliary output2 Key hole NO COM NC AUXOUT4 D AUXOUT3 Auxiliary output1 Backup battery Power supply Control panel NO COM NC AUXOUT2 { { { { D AUXOUT1 2.Components D 4# Door Button B 4# Door wiegand reader 5.RS485 address setting, Restore factory setting, Terminal resistance setting 7.Equipment communication Set RS485 address through DIP switch: The background PC software is able to communicate with the system according to two protocols(RS485 and TCP/IP) for data exchange and remote management. The communication cable should be away from high-voltage lines as far as possible. Do not keep the communication cable in parallel with power cords or bind them together. 1) Place 1-6 on DIP switch are for setting the number of control panel when communicating through RS485, it is adopted for binary coding, and little endian, the address represented by place 1-6 are shown as figurue(5-1). 2) Before setting the address, please keep the system is power off, Jump place 1-6 to desired status, and the address number shall not be the same as another one in the network. For example: to set the device number as 39 (39=1+2+4+32), the corresponding RS485 code is 111001, then Jump place 1,2,3 and 6 at “ON” status. ON 1 2 3 4 5 6 7 1.TCP/IP Communication 8 PC 3) Place 7 is for restoring factory default settings, Jump it for three times within 10 seconds and restart the system, then all information in RAM of control panel will be cleared and the system restores factory default settings. Switch 4) Place 8 is for setting terminal resistance when communicating through RS485. Jump it at “ON” status, then it is equivalent to have a terminal resistance of 120 ohm between 485+ and 485-. 1# control panel Diagram of places of DIP switch. LINK AUX3 AUX4 +12V GND 485485+ EXT IN BUTTON1 BUTTON2 READER2 IN GND BUTTON3 BEEP GLED WD1 WD0 GND +12V READER3 IN GND BUTTON4 WD1 WD0 GND V+ V- POWER READER4 BEEP GLED 1 LOCK POWER +12V GND +12V 1 LOCK4 SEN GND NO COM NC BEEP GLED WD1 WD0 1 SEN GND NO COM NC IN GND 1 SEN GND NO COM NC LOCK3 READER4 LOCK2 BUTTON4 LOCK1 READER3 NO COM NC SEN GND NO COM NC GND BEEP GLED WD1 WD0 GND +12V READER1 NO COM NC AUXOUT4 BUTTON3 +12V POWER NO COM NC AUXOUT3 READER2 WD1 WD0 GND V+ V- NO COM NC AUXOUT2 BUTTON2 IN GND AUXOUT1 READER1 BEEP GLED WD1 WD0 GND +12V BEEP GLED AUX2 PC BUTTON1 IN GND TX RX GND IN GND TX RX GND +12V 1 LOCK POWER RUN CARD BEEP GLED WD1 WD0 1 LOCK4 SEN GND NO COM NC IN GND 1 SEN GND NO COM NC IN GND 485+ 485GND AUX1 LAN 5 6 7 8 EXT GND 485485+ IN ACT Advanced Access Control +12V BEEP GLED WD1 WD0 GND +12V 1 SEN GND NO COM NC LOCK3 +12V GND SEN GND NO COM NC LOCK2 +12V NO COM NC LOCK1 READER4 POWER NO COM NC AUXOUT4 BUTTON4 LOCK POWER BUTTON4 WD1 WD0 GND NO COM NC AUXOUT3 READER3 BEEP GLED V+ V- BUTTON3 IN GND AUXOUT2 READER2 BEEP GLED WD1 WD0 GND +12V AUXOUT1 BUTTON2 IN GND NO COM NC ON 1 2 3 4 AUX4 TX RX AUX3 PC READER1 GND +12V 1 LOCK4 SEN GND NO COM NC BEEP GLED WD1 WD0 1 LOCK3 SEN GND NO COM NC IN GND BUTTON1 LOCK2 SEN GND NO COM NC IN GND BEEP GLED WD1 WD0 GND +12V 1 SEN GND NO COM NC 485+ 485GND GND IN GND IN GND AUX2 ON 5 6 7 8 Advanced Access Control EXT GND 485485+ IN GND AUX1 LAN 1 2 3 4 AUX4 +12V IN ACT TX RX 1 NO COM NC LOCK1 READER3 IN GND READER4 LOCK POWER WD1 WD0 GND POWER AUXOUT4 BEEP GLED WD1 WD0 GND +12V BEEP GLED V+ V- NO COM NC BUTTON3 IN GND NO COM NC AUXOUT3 READER2 GND +12V 1 LOCK4 SEN GND NO COM NC BEEP GLED WD1 WD0 1 LOCK3 figure(5-1) SEN GND NO COM NC GND BUTTON2 LOCK2 SEN GND NO COM NC IN READER1 LOCK1 SEN GND NO COM NC GND BEEP GLED WD1 WD0 GND +12V BUTTON1 AUXOUT4 NO COM NC 1 NO COM NC NO COM NC AUXOUT2 GND 485485+ IN 1 NO COM NC AUXOUT3 Restore factory setting AUXOUT2 RS485 terminal resistance NO COM NC AUXOUT1 TX RX TX RX AUXOUT1 32 16 8 4 2 1 485+ 485GND AUX3 PC 8 +12V EXT 7 IN GND AUX4 6 PC 5 GND AUX3 5 6 7 8 4 Advanced Access Control TX RX IN GND IN GND TX RX AUX2 ON 1 2 3 4 3 IN ACT 485+ 485GND GND SD Card SD Card IN GND AUX2 5 6 7 8 LAN IN GND 2 Advanced Access Control AUX1 IN GND 1 ON 1 2 3 4 SD Card IN ACT LINK AUX1 LAN IN GND LINK n# control panel LINK IN GND ON 2# control panel SD Card +12V +12V RUN CARD GND RUN CARD GND 2.RS485 Communication +12V +12V RUN CARD GND GND 485- 6.Connection of lock 5、门锁连接 485+ 485 serial line Converter 1) Control panel provides lock control output interfaces. For NO lock ,it is open when power is on, and closed when power is off, so COM and NO interfaces should be used; For NC lock, it is open when power is off, and closed when power is on, so COM and NC interfaces should be 485+ 485+ 485+ used. 485- 485- 485- GND GND GND PC 2 3 4 5 1 2) Control panel supports “dry mode” and “wet mode” by setting the jumper, it is “wet mode” when connecting “V+ V-” Input interfaces to supply power for locks, please shorten 2-3 and 4-5 +12V GND 485485+ EXT IN BUTTON1 AUXOUT3 NO COM NC IN GND BUTTON4 WD1 WD0 GND POWER DIP switch READER4 BEEP GLED 7 8 BEEP GLED WD1 WD0 GND +12V READER3 LOCK POWER V+ V- BUTTON3 READER4 +12V RUN CARD READER2 BUTTON4 WD1 WD0 GND POWER BUTTON2 LOCK4 SEN GND NO COM NC IN GND 1 LOCK3 READER3 IN GND GND +12V 1 LOCK2 SEN GND NO COM NC BEEP GLED WD1 WD0 1 LOCK1 SEN GND NO COM NC IN GND 1 AUXOUT4 NO COM NC SEN GND NO COM NC GND BEEP GLED WD1 WD0 GND +12V READER1 NO COM NC ON AUX4 AUXOUT2 BUTTON3 BEEP GLED WD1 WD0 GND +12V +12V GND AUXOUT1 READER2 LOCK POWER V+ V- IN GND BEEP GLED 1 LOCK4 +12V RUN CARD NO COM NC GND +12V 1 LOCK3 READER4 SEN GND NO COM NC BUTTON2 LOCK2 BUTTON4 1 WD1 WD0 GND SEN GND NO COM NC BEEP GLED WD1 WD0 1 LOCK1 SEN GND NO COM NC IN GND 1 AUXOUT4 READER3 IN GND BEEP GLED POWER BUTTON3 BEEP GLED WD1 WD0 GND +12V TX RX AUX3 PC AUXOUT3 READER2 NO COM NC SEN GND NO COM NC IN GND BEEP GLED WD1 WD0 GND +12V READER1 AUXOUT2 NO COM NC 485+ 485GND AUX2 5 6 7 8 Advanced Access Control GND IN GND TX RX BUTTON1 AUXOUT1 NO COM NC IN ACT AUX1 ON GND 485485+ IN GND 1 2 3 4 TX RX +12V EXT PC BUTTON2 IN GND +12V +12V GND RUN CARD LED 1 2 3 4 5 Jumper terminal Notes： 1) Internationally accepted RVSP(shielded twisted-pair) wires should be used for communication to effectively avoid interference. RS485 communication wires should be connected by means of bus cascade connection. 2)Considering stability of communication, it is recommended the length of RS485 bus is less than 600m 3) One RS485 BUS may hold 63 units of control panel, but it is not recommended to connect with more than 32 units access control panels.. 4)When the bus is longer than 300m, to enhance the stability of communication, it is necessary to keep place 8 of DIP switches of the first and the last control panel at “ON” status. As shown in the figure above, place 8 of the DIP switches of units 1# and 8# + - ON is placed at "ON “Wet mode” wiring diagram of lock connecting with external power supply. NO COM NC GND +12V +12V GND 485+ 485GND IN GND LAN Advanced Access Control AUX4 IN GND AUX3 GND 5 6 7 8 READER1 BEEP GLED WD1 WD0 1 LOCK POWER +12V RUN CARD LOCK4 READER4 WD1 WD0 GND LOCK3 BUTTON4 BEEP GLED V+ V- IN GND BUTTON1 LOCK2 READER3 IN GND SEN GND NO COM NC IN GND BEEP GLED WD1 WD0 GND +12V 1 LOCK1 BUTTON3 BEEP GLED WD1 WD0 GND +12V SEN GND NO COM NC ACT SD Card AUX2 ON 1 2 3 4 GND 485485+ IN TX RX 1 AUXOUT4 AUXOUT3 READER2 IN GND +12V GND AUXOUT2 BUTTON2 GND +12V POWER AUXOUT1 READER1 BEEP GLED WD1 WD0 BUTTON1 V+ V- TX RX +12V EXT PC EXT + - LOCK POWER Lock power input IN GND 1 SEN GND NO COM NC GND 1 NC Lock GND 485485+ BEEP GLED WD1 WD0 GND +12V 1 SEN GND NO COM NC LOCK4 FR107 SEN GND NO COM NC +12V IN 1 SEN GND NO COM NC LOCK3 NC SEN GND NO COM NC LOCK2 + Diode NO COM NC LOCK1 - NO COM NC AUXOUT4 COM AUXOUT3 GND AUXOUT2 + NO COM NC NO COM NC NO COM NC TX RX AUXOUT1 SEN NO COM NC SEN GND NO COM NC AUX4 PC - - TX RX NO COM NC AUX3 Advanced Access Control 485+ 485GND NO COM NC 485+ 485GND AUX4 Advanced Access Control AUX3 5 6 7 8 IN GND AUX2 ON 1 2 3 4 GND AUX2 GND IN GND 5 6 7 8 + Diode NO LOCK ON 1 2 3 4 LOCK Enlarged diagram of lock ports IN ACT AUX1 LAN IN GND FR107 ACT IN GND TX RX SD Card IN GND NO Lock IN IN GND LAN LAN LINK IN GND 8# control panel LINK SD Card AUX1 IN GND AUX1 “wet mode”, please refer to <>. LINK SD Card 1 2 3 4 5 6 LINK 3) When the Electrical Lock is connected to the Access Control System, you need to parallel one FR107 diode (equipped in the package) to prevent the self-inductance EMF affecting the system, do not reverse the polarities. 2# control panel 1# control panel . Equipment factory default setting is dry mode. For setting “dry mode” and 1 2 3 4 5 6 7 8 " status.