Transcript
Quick Installation Guide
SL-204-DDL
2 Port Dual-Link Quad Monitor KVM Switch – Dual Link DVI/USB & Audio
The SL-204-DDL features Active Sync Replication™ (A.S.R.) technology that offers full-time DDC (Display Data Channel) emulation for 100% video compatibility with all types of Operating Systems including Windows 7 and Windows 8 that require more critical DDC communication.
INSTALLATION
SL-204-DDL 2 Port Dual Link DVI Quad Monitor KVM Switch – Dual Link DVI-I/USB & Audio
Quick Installation Guide
1. Power up your KVM Switch by connecting the external power adapter to it. 2. Connect the shared USB keyboard, USB mouse, dual monitors, speaker/headphone and microphone to corresponding ports on the console section of the KVM Switch.
OPERATION You can select which computer to connect to via either the front panel push buttons or keyboard hotkeys. (1) Front Panel Push Buttons The front panel push buttons allow you direct control over the KVM switching operation. Simply press the button to switch to the either corresponding PC port. (2) Keyboard Hotkeys For keyboard hotkey commands, please refer to the “Quick Reference Sheet”.
Note: The lower two USB ports are for keyboard and mouse and the upper two USB hub ports are for connected optional USB devices
SL-204-DDL – Rear View
INTRODUCTION The SL-204-DDL Dual Link Quad Monitor DVI USB KVM switch features not only 3D display support but digital video (2560 x 1600) and analog video (2048 x 1536) support for your maximum convenience in adapting to your display requirements as well.
3. Connect each KVM PC port to a computer, using two DVI video cables (male to male), one USB cable (type A to type B) and one audio & mic combo cable (male to male). 4. Connect up to two optional USB devices (USB flash drive, HDD or CD/DVD/Blu-ray) to the USB hub ports to share between connected computers. You can now begin to use the KVM switch.
With the TTU (True Transparent USB) Emulation Technology, the SL-204-DDL Quad monitor DVI USB KVM switch offers 100% compatibility with all and any types of advanced USB keyboards and mice. It features 2 channel stereo sound for theater audio experience and its audio & mic switching function offers you uninterrupted multimedia experience while performing KVM switching. It also offers multi-platform support for PC and Macs.
Rev. 1.0
Copyright© All rights reserved
Quick Reference Sheet
SL-204-DDL
Quick Command Select PC Port (Jointly select PC port/ hub port control/ audio & mic, if binding is enabled) Select Hub Port Control (Jointly select PC and hub port control, if binding is enabled) Select Audio & mic Port (Jointly select PC port and audio & mic, if binding is enabled) Bind PC and Hub Port Control Switching Unbind PC and Hub Port Control Switching Bind PC and Audio & mic Switching Unbind PC and Audio & mic Switching Previous PC port (Jointly select PC/ hub port control, if binding is enabled) Next PC port (Jointly select PC/ hub port control, if binding is enabled) Previous PC port Beeper Define Hotkey Preceding Sequence1
Reference
Hotkeys ScrLk + ScrLk + (1~2) ScrLk + ScrLk + [Fn(1~4)] ScrLk + ScrLk + [Fn(5~8)] ScrLk + ScrLk + Z
2 Port Dual-Link Quad Monitor KVM Switch – Dual Link DVI/USB & Audio
Sheet
Front Panel Push Buttons Press the corresponding button to select the active PC port. Press the button to toggle the specific PC+USB hub port control. (It works only if PC port/ hub port control binding is enabled.) --
Description Select the PC port
Move Hub Port (1~4) Move audio & mic port
--
Bind PC Port with Device Hub Port
ScrLk + ScrLk + X
--
Unbind PC Port with Device Hub Port
ScrLk + ScrLk + Q
--
Bind PC Port with audio & mic Port
ScrLk + ScrLk + W
--
Unbind PC port with audio & mic Port
ScrLk + ScrLk + Up Arrow
--
Next lower PC Port
ScrLk + ScrLk + Down Arrow
--
Next higher PC Port
ScrLk + ScrLk + [Backspace] ScrLk + ScrLk + B ScrLk + ScrLk + H+ [ScrLK/CAPS/ ESC/F12/
---
Previous PC Port Toggle Beeper On/Off
--
Select Hotkey Header [ScrLK/CAPS/ESC/F12/NUM LOCK]
--
Start Autoscan
--
Autoscan duration adjust to (10~60 seconds)
NUM LOCK]
Autoscan
ScrLk + ScrLk + S
Autoscan with Programmable Delay Time
1 10” ; 2 20” ; 3 30” ; 4 40” ; 5 50” 6 60” ;
Stop Autoscan
[Any key]
ScrLk + ScrLk + S + (1~6)
Press any button
Stop Autoscan during scan mode
Notes: 1. Hotkey sequence = [ScrLk] + [ScrLk] + Command key(s). User-definable Preceding sequence = ScrLK, CAPS, ESC, F12 or NUM LOCK.
Rev. 1.0
Copyright© All rights reserved
