Transcript
PIPE & WALL VIDEO INSPECTION SYSTEMS
USER MANUAL For
3688 SERIES ASSEMBLING AND OPERATING INSTRUCTIONS
1
Read instructions carefully before operating this system WARNING 1.
Never use this device in an environment with explosive materials such as GAS, OIL, ETC. 2. Avoid using the device in extremely cold, hot or humid environment; otherwise it may damage the device. Do not drop or press hard on the device. 3. Avoid using the parts / components from other manufacturers to this system, which may damage the equipment due to the uncompatibility. 4. Warranty invalidation if the device is disassembled by users or if there are any physical damages. 5. Always back up your data before connecting your USB stick / Micro SD Card to this system. The manufacturer is not responsible for any data damage or loss on your USB stick / Micro SD Card for any reason. 6. Do not disconnect the unit while recording or playing. It may damage the unit and/or the USB stick / Micro SD Card. 7. Don’t misuse the Battery Charger Cable and Power Cord, otherwise the battery pack may be damaged or the system cannot work properly. 8. The system’s PUSH CABLE made of fiberglass is very rigid and not flexible. It CAN NOT be bent sharply or pushed too hard; otherwise it will be broken. 9. If you have an extra portable cable reel, and try to put it in the case after use, you must put it in the right position; otherwise, LCD monitor may be broken by the part on the reel when you close the case. 10. Waterproof camera head should NOT be used under the water of over 100FT. 11. We reserve the right to make any change about our products without any notice in advance. 12. We assume no liability for damage and/or injury resulting from use of equipment supplied by our company.
2
CONTENTS Assembly Drawing and Parts List..........................................................4 Specifications..............................................................................5 User Manual..........................................................................................6 Display Device…………………………………………………………….7 Counter....................................................................................................8 Control box………………………………………………………………….9 Pan-Tilt Camera Head.....................................................................11 Cable Reel............................................................................................13 Remote Control ………………………….......................................14 LED brightness......................................................................................15 Video recording and snap shooting............................................... 15 Recharging the Battery.........................................................17 Trouble Shooting ……........................................................................19 Daily Maintenance………………………………………..……………........19 System Connection Diagram……………………………………………19
3
Assembly Drawing and Parts List Part No.
Description
1
ROTATE CAMERA
2
_7 INCH _10 INCH MONITOR
3
_60M(200FT) _90M(300FT) _120M(400FT) CABLE
4
CFIBERGLASS CABLE BATTERY CHARGER
5
BATTERY CASE
6
FUSE BAG
7
POWER ADAPTER
8
CAMERA SKIDS
9
3M&5M VIDEO CABLE
10
REMOTE CONTROL
11
DISC
12
SKIDS SCREW (12 PCS)
13
Control box
13
2
1
1
4
Specifications Item Power adapter Battery Case Length of Cable
Description 110VAC~240VAC 12VDC LI-ION battery
Camera Light Source Camera Angle-of-View
Built-in White LED lights (14PCS) Camera swing angle: 180°
_60M(200FT) _90M(300FT) _120M(400 FT)
Camera Inclination Detection: 1. Measuring range: -90°~ +90° 2. Camera Rotating Angle Camera Image Monitor Screen Size Monitor Picture Resolution Monitor Input Voltage System Operating Temperature
Resolution: 1°
360° about 0.44Mpixel_ P A L _ o r 0.38Mpixel_NTSC_ 7”OR10” TFT LCD Color Monitor 1024_768 pixel (for 10”LCD) 800_480pixel(for 7”LCD) 12 Volts DC -28°C to 50°C
5
User Manual Application 1. 2. 3. 4. 5. 6. 7.
WATER SUPPLY WASTE WATER ELECTRICAL AIR CONDITIONER CABLE DUCTING DUCTED VACCUM SYSTEMS PLUMBING BUILDINGS
WARNING: NEVER USE THIS DEVICE IN AN ENVIRONMENT WITH EXPLOSIVE MATERIALS SUCH AS GAS, OIL, ETC.
Before use 1.1 Please connect the camera head with the cable & reel. 1.2 Please connect the cable reel with the CAM port on the front panel with the black soft cable and screw it tightly 1.3 Please insert USB/SD in the port 1.4 Please insert the DC power in the socket of DC on the front panel; then the power indicator light will be on and the system will start to work automatically after about 7 seconds
6
Display Device
1. 12V DC 2. UP 3. DOWN 4. DVR POWER 5. RETURN 6. RECORDING 7. LEFT 8. SD 9. RIGHT 10. USB
11. 12. 13. 14. 15. 16. 17. 18. 19. 20.
PLAY/ENT IR REM POWER CAM MIC MIC POWER ON/OFF MIC LED USB PORT TF
7
Counter: Cable with optoelectronic meter counter 1.Reset 2.Metric & Imperial conversion 3.Display of Metric or Imperial
8
Control box:
Item Switch Socket K1 K2 K3 K4 K5 K6 K7 K8 K9 Power
feature Power switch POWER &AVR Socket UP DOWN TURN RIGHT TURN LEFT HOME LED UP LED DOWN FOCUS UP FOCUS DOWN Power LED
9
Connection diagram for controller & Peripheral Unit_ _DISPLAY_ _DVR_ _DC POWER_
DVR DISPLAY
To control panel: 1_ POWRE 2_ DVR DATA.
To Cable: 1_ DC POWER; 2_ RS485 DATA; 3 _ VIDEO SIGNAL.
6
10
Pan-Tilt Camera Head
I_Working environment_ 1_ Temperature: -28__+50_ 2_ Humidity_90%RH (non-condensation) II_Storage environment_ 1_ Temperature: -20__+60_ 2_ Humidity: 90%RH(non-condensation) III. Main Technical Indicators: 1. Power source input: DC 12~18V,8W_maximum_ 2. Camera module: 1) Image sensor:1/3 Sony Super HAD _ 2) Total pixels: about 0.44Mpixel_PAL_or 0.38Mpixel_NTSC_ 3) Horizontal resolution: 600 TVL 4) Minimum illumination: 0.05LUX/F1.2 5) Camera swing angle: 180° 6) LED quantity: 14pcs 7) Light Cup Angle: 45° 11
3. Camera Inclination Detection: 1) Measuring range: -90°~ +90° 2) Resolution: 1°
12
Cable reel
1. Meter Counter Box 2. Reset Button 3. Display 4. Meter& imperial Button 5. Female Plug 6. Cable Wheel
13
Remote Control Remote control has the same basic functions with the buttons on the front panel.
14
LED brightness During the status of monitoring images or video recording, press LEFT/RIGHT button and a pop up will be displayed, then press LEFT/RIGHT to adjust the LED brightness; press RETURN to confirm and exit the pop up. Video recording and snap shooting 1.1.Recording Press RETURN button and main menu Pops up (Picture 1), then press RIGHT Button to select the icon , then Picture1 Press PLAY/ENT to start recording the Videos. At This time, RECORDIN and LED lights Will be on and press PLAY/ENT button again to snap shooting; Press RETURN button to exit recording and save. You can only take pictures or monitor the pipeline when selecting the icon
in Picture 1. 9
2.1_Playing Press RIGHT button to select , then press Picture 2 PLAY/ENT, a pop-up (Picture 2) will display on the screen and you can select the videos or files to play the recorded; Press UP/DOWN button to enter/exit.; Press PLAY/ENT to pause Playing. 2.2_Deleting Press LEFT/RIGHT during the monitoring images or videos playing to display the pop-up (Picture 3); Press UP/DOWN to select your choice: select Picture3 to give up and exit deleting; select to confirm deleting. 3.1.System Setting Select the setting icon in the main menu to change the setting and then the main menu for Setting will display (Picture 4). Picture 4 3.2.Playing setting Select player icon to change the setting 15
No Single Rotating Single Rotating Multiple Rotating 3.3. Storage and Formatting Select storing option icon to know the current storage and formatting. Left is the TF card volume; Right is the USB volume. Total Storage Files Volume Formatting 10
3.4. Time and Date Setting Select Clock setting icon
t to set the time_Press UP/DOWN
to select the target and LEFT/RIGHT to adjust the numbers. PLAY Button for Time Zone Change Date Setting Time Setting
3.5. Version Information Select version icon to know the current software.
16
Recharging the Battery 1) Plug the charger into the AC socket on the wall and insert the other end into the DC jack of battery box (See Figure2- A). Note : Don’t misuse the battery charger cable and power code, otherwise the battery pack may be damaged, or the system cannot work properly. 2) Press the charge button (See Figure2-B) while the Battery Box is turned off. The battery can be charged while the battery box is on and the device is being used. However, once the power in the battery runs completely out, it can only be charged when the Battery Box is turned off. 3) The charge LED will be red during charging and will turn green when charging is over (Normal charging time: 5 - 6 hours).
Figure 2
IMPORTANT MESSAGE: Do not overcharge the battery! Overcharging can result in acid leaking from or damage to the battery.
17
Battery specifications: 1. 2. 3. 4. 5. 6. 7. 8.
TOTAL POWER 12W LI-ION BATTERY 12VDC MAX._ 40Wh CHARGER 13.5V 800mA CHARGE TIME 6 HOURS WORKING TIME ≥120 MINUTES PROTECTIVE VOLTAGE 8.1V THE VOLTAGE BEFOR DISCHARGING 12.6V LOAD CURRENT 1100mA(INPUT 12.2V HOUR)
18
TROUBLE SHOOTING Trouble
Reason/Solution
Black Screen
Abnormal power supply/Check if the power is connected well to ensure the sufficient power. No signal transfer/Check if the connection is good and reconnect all parts referring to the connection diagram. Not inserting the USB/SD or the USB/SD has no spare space/Insert the USB/SD with enough space. Camera head is not on the right position/Screw off the camera head and on the cable connector again. Battery not fully recharged/ Fully charge the battery and then use. Poor contact of the power adapter or damaged battery/ Ensure the good contact with the charger or change the battery.
No signal No recording Lights off Not enough power Battery not charging
Daily maintenance 1.1. Keep the product clean. Clean the camera head and cable & reel before disconnecting to avoid the water splashed on the PCB board on the camera head or gold pins. Once there are splashed water drops, please clean the parts with the dry cloth immediately. Disconnect the parts after the product is dry. Put the cover on the camera head connector and CAM connector on the front panel. Put it away in the same way as when the package is received. 1.2. Put it away in the dry environment and keep it out of reach of children. System Connection Diagram Control Box (Option)
Display Screen
Soft -----Cable
Pan -----180º/360º Tilt Camera 2.4G Wireless Text Writer
Cable & Reel
Camera Head
19
