Transcript
DVD PLAYER DVD-909 DVD-709
SERVICE MANUAL
SERVICE
Manual
DVD-909/709
DVD PLAYER
CONTENTS 1. Precautions 2. Reference Information
ELECTRONICS
3. Product Specification 4. Operating Instructions 5. Disassembly and Reassembly
SKIP
STANDBY
PHONE
DVD/VIDEO-CD/CD PLAYER DVD-909
LEVEL
OPEN/ OPEN/ OPEN/ CLOSE CLOSE CLOSE
POWER MIN
MAX
ADVANCED DOLBY DIGITAL DECORDER BUILT-IN
SPATIALIZER N-2-2 DIGITAL VIDEO
DVD-909
6. Circuit Descriptions 7. Troubleshooting 8. Exploded Views and Parts List 9. Electrical Parts List 10. Block Diagrams
SKIP
STANDBY
11. PCB Diagrams
DVD/VIDEO-CD/CD PLAYER DVD-709 OPEN/ OPEN/ CLOSE CLOSE
POWER
24bit 96kHz AUDIO D/A CONVERTER
SPATIALIZER N-2-2 DIGITAL VIDEO
DVD-709
© Samsung Electronics Co., Ltd. NOV. 1999 Printed in Korea AH68-00137A REV.-2
12. Wiring Diagram 13. Schematic Diagrams
1. Precautions 1-1 Safety Precautions 1) Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following items: (1) Be sure that no built-in protective devices are defective or have been defeated during servicing. (1)Protective shields are provided to protect both the technician and the customer. Correctly replace all missing protective shields, including any remove for servicing convenience. (2)When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including, but not limited to, nonmetallic control knobs, insulating fish papers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. (2) Be sure that there are no cabinet openings through which adults or children might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, excessively wide cabinet ventilation slots, and an improperly fitted and/or incorrectly secured cabinet back cover. (3) Leakage Current Hot Check-With the instrument completely reassembled, plug the AC line cord directly into a 120V AC outlet. (Do not use a isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1270 (40.7). With the instrumentÕs AC switch first in the ON position and then in the OFF position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinets, screwheads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5mA. Reverse the instrument power cord plug in the outlet and repeat the test. See Fig. 1-1.
Any measurements not within the limits specified herein indicate a potential shock hazard that must be eliminated before returning the instrument to the customer. (READING SHOULD NOT BE ABOVE 0.5mA) LEAKAGE CURRENT TESTER
DEVICE UNDER TEST TEST ALL EXPOSED METER SURFACES 2-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)
EARTH GROUND
Fig. 1-1 AC Leakage Test (4) Insulation Resistance Test Cold Check-(1) Unplug the power supply cord and connect a jumper wire between the two prongs of the plug. (2) Turn on the power switch of the instrument. (3) Measure the resistance with an ohmmeter between the jumpered AC plug and all exposed metallic cabinet parts on the instrument, such as screwheads, antenna, control shafts, handle brackets, etc. When an exposed metallic part has a return path to the chassis, the reading should be between 1 and 5.2 megohm. When there is no return path to the chassis, the reading must be infinite. If the reading is not within the limits specified, there is the possibility of a shock hazard, and the instrument must be re-pared and rechecked before it is returned to the customer. See Fig. 1-2. Antenna Terminal
Exposed Melal Part
ohm
ohmmeter
Fig. 1-2 Insulation Resistance Test Samsung Electronics
1-1
Precautions
2) Read and comply with all caution and safety related notes non or inside the cabinet, or on the chassis. 3) Design Alteration Warning-Do not alter of add to the mechanical or electrical design of this instrument. Design alterations and additions, including but not limited to, circuit modifications and the addition of items such as auxiliary audio output connections, might alter the safety characteristics of this instrument and create a hazard to the user. Any design alterations or additions will make you, the service, responsible for personal injury or property damage resulting therefrom. 4) Observe original lead dress. Take extra care to assure correct lead dress in the following areas: (1) near sharp edges, (2) near thermally hot parts (be sure that leads and components do not touch thermally hot parts), (3) the AC supply, (4) high voltage, and (5) antenna wiring. Always inspect in all areas for pinched, out-of-place, or frayed wiring, Do not change spacing between a component and the printed-circuit board. Check the AC power cord for damage.
1-2
5) Components, parts, and/or wiring that appear to have overheated or that are otherwise damaged should be replaced with components, parts and/ or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard. 6) Product Safety Notice-Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by shading, an ( )or a ( )on schematics and parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might created shock, fire and/or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate.
Samsung Electronics
Precautions
1-2 Servicing Precautions CAUTION : Before servicing Instruments covered by this service manual and its supplements, read and follow the Safety Precautions section of this manual. Note : If unforseen circument create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions. Remember: Safety First.
1-2-1 General Servicing Precautions (1) a. Always unplug the instrumentÕs AC power cord from the AC power source before (1) re-moving or reinstalling any component, circuit board, module or any other instrument assembly, (2) disconnecting any instrument electrical plug or other electrical connection, (3) connecting a test substitute in parallel with an electrolytic capacitor in the instrument. b. Do not defeat any plug/socket B+ voltage interlocks with which instruments covered by this service manual might be equipped. c. Do not apply AC power to this instrument and /or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed. d. Always connect a test instrumentÕs ground lead to the instrument chassis ground before connecting the test instrument positive lead. Always remove the test instrument ground lead last.
(4) An insulation tube or tape is sometimes used and some components are raised above the printed wiring board for safety. The internal wiring is sometimes clamped to prevent contact with heating components. Install such elements as they were. (5) After servicing, always check that the removed screws, components, and wiring have been installed correctly and that the portion around the serviced part has not been damaged and so on. Further, check the insulation between the blades of the attachment plug and accessible conductive parts.
1-2-2 Insulation Checking Procedure Disconnect the attachment plug from the AC outlet and turn the power ON. Connect the insulation resistance meter (500V) to the blades of the attachment plug. The insulation resistance between each blade of the attachment plug and accessible conductive parts(see note) should be more than 1 Megohm. Note : Accessible conductive parts include metal panels, input terminals, earphone jacks, etc.
Note : Refer to the Safety Precautions section ground lead last. (2) The service precautions are indicated or printed on the cabinet, chassis or components. When servicing, follow the printed or indicated service precautions and service materials. (3) The components used in the unit have a specified flame resistance and dielectric strength. When replacing components, use components which have the same ratings. Components i-entified by shading, by( ) or by ( ) in the circuit diagram are important for safety or for the characteristics of the unit. Always replace them with the exact replacement components.
Samsung Electronics
1-3
Precautions
1-3 ESD Precautions Electrostatically Sensitive Devices (ESD) Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive Devices(ESD). Examples of typical ESD devices are integrated circuits and some field-effect transistors and semiconductor chip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. (1) Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test.
(7) Immediately before removing the protective materials from the leads of a replacement ESD device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION : Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. (8) Minimize bodily motions when handling unpackaged replacement ESD devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ESD device).
(2) After removing an electrical assembly equipped with ESD devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. (3) Use only a grounded-tip soldering iron to solder or unsolder ESD devices. (4) Use only an anti-static solder removal devices. Some solder removal devices not classified as Òanti-staticÓ can generate electrical charges sufficient to damage ESD devices. (5) Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESD devices. (6) Do not remove a replacement ESD device from its protective package until immediately before your are ready to install it.(Most replacement ESD devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive materials).
1-4
Samsung Electronics
Precautions
1-4 Handling the optical pick-up The laser diode in the optical pick up may suffer electrostatic breakdown because of potential static electricity from clothing and your body.
WRIST-STRAP FOR GROUNDING
1M
The following method is recommended. (1) Place a conductive sheet on the work bench (The black sheet used for wrapping repair parts.) (2) Place the set on the conductive sheet so that the chassis is grounded to the sheet. (3) Place your hands on the conductive sheet(This gives them the same ground as the sheet.) (4) Remove the optical pick up block (5) Perform work on top of the conductive sheet. Be careful not to let your clothes or any other static sources to touch the unit.
THE UNIT
1M
CONDUCTIVE SHEET
Fig.1-3 (6) Short the short terminal on the PCB, which is inside the Pick-Up ASSÕY, before replacing the PickUp. (The short terminal is shorted when the PickUp AssÕy is being lifted or moved.) (7) After replacing the Pick-up, open the short terminal on the PCB.
3 Be sure to put on a wrist strap grounded to the sheet. 3 Be sure to lay a conductive sheet made of copper etc. Which is grounded to the table.
Samsung Electronics
1-5
Precautions
1-5 Pick-up disassembly and reassembly 1-5-1 Disassembly 1-5-2 Assembly 1) Remove the power cable. 2) Switch SW3 on deck PCB to ÒOFFÓ before removing the FPC. ( Inserted into Main PCB CN6. See Fig. 1-4) 3) Disassemble the deck. 4) Disassemble the deck PCB.
1) Replace the Pick-up. 2) Assemble the deck PCB. 3) Reassemble the deck. 4) Insert FPC into Main PCB CN6 and switch SW3 on deck PCB to ÒONÓ. (See Fig 1-4)
Note : If the assembly and disassembly are not done in correct sequence, the Pick-up may be damaged.
FPC
SW3 OFF
TO MAIN PCB (CN6)
ON
Fig. 1-4
1-6
Samsung Electronics
2. Reference Information 2-1 IC Dsecriptions 2-1-1 AIC1 (AK4324 ; Digital-to-Analog Converter) DIF0
LRCK BICK SDATA
DIF1
DIF2
DEM0
AVDD
AVSS
De-emphasis Control
Serial Input Interface
PD
DEM1
DZFL
AOUTL+
8X Interpolator
∆∑ Modulator
SCF
8X Interpolator
∆∑ Modulator
SCF
AOUTL-
SMUTE DFS
AOUTR+ AOUTR-
Clock Divider DZFR
MCLK
PIN I / O NAME
CKS
DVDD
FUNCTION
DVSS
VREF
PIN I / O NAME
FUNCTION
13
I
DIF0
Digital input format pin
1
-
DVSS
Digital ground pin
2
I
DVDD
Digital power supply
14
I
DIF1
Digital input format pin
3
I
CKS
Master clock select pin (Internal pull-down pin) Nomal speed "L":MCLK = 256fs, "H":MCLK = 384fs Double speed "L":MCLK = 128fs, "H":MCLK = 192fs
15
I
DIF2
Digital input format pin
4
I
MCLK
Master clock input pin
16
0
AOUTR-
Rch negative analog output pin
5
I
PD
Power-Down mode pin. When at "L", the AK4324 is in power-down and is held in rest. The AK4324 should always be reset upon power-pin
17
O
AOUTR+
Rch positive analog output pin
6
I
BICK
Audio serial data input pin 64fs clock is recommended to be input on this pin
18
O
AOUTL-
Lch negative analog output pin
7
I
SDATA
Audio serial data input pin 2's complement MSB-first data is input on this pin.
19
O
AOUTL+
Lch positive analog output pin
8
I
LRCK
L/R clock pin.
20
-
AVSS
Analog ground pin
9
I
SMUTE
Soft mute pin When this pin goes "H", soft mute cycle is initiated When returning "L", the output mute releases.
21
O
VREF
Voltage reference input pin
10
I
DFS
Double speed sampling mode pin (Internal pull-down pin) "L":normal speed, "H":double speed
22
O
AVDD
Analog power supply pin.
11
I
DEM0
De-emphasis frequency select pin
23
O
DZFR
Rch zero input detect pin
12
I
DEM1
De-emphasis frequency select pin
24
O
DZFL
Lch zero input detect pin
Note : Allinput pins except internal pull-down pins should not be left floating.
Samsung Electronics
2-1
Reference Information
2-1-2 RIC1 (KS1461 ; RF)
83 82 81 80 79 78 77 76
AGC-HOLD(OOH)
ADVD
5
AGC_DET
RF MUX
BCA BLOCK 74 BCAI
RF Equalizer
RF SLM & AGC
C D
BCA
RFRP
GAIN_EQ(02H)
CDRSEL(00H)
TE1RES DELAY_SEL(OOH) PLLCTL TBAL(O1H)
RREFEQ 10
VREF GENERATOR
DELAY
D GCA
RREF 11
CD1 S12 DVD1 DVD2 LDONB FLT_CTL CDRSEL TESEL AGC-HOLD TBAL GAIN_TE3 ENV_SEL DVCTL_SEL DPD_MUTE GAIN_EQ GAIN_FE GAIN_ABCD TE_OFST FE_OFST ABCD_OFST DELAY_CD DELAY_AB PDLIMIT ga_RFSUM HOLD_CTL ga_PLLDP ga_PLLDN
HOLD_CTL(O8H) DPDMUTE DPD_MUTE(O2H) SEOFHOLD FLT_CTL(OOH) CAL_ENDB(O2H)
DPDEQ1
9
PD,LPF
COM
EQ
D
TEOPST(04H) MUX3
PDLIMITRES
TE1_LIMIT
D GCA
COM
EQ
D
DPDEQ2 FAULTOUT
VREFEQ 12
EQ VC AMP
GAIN_TE3(02H)
E 13
DELAY_SEL(00H) PLLCTL
TE38
F 14
AUTO OFSTCTL
RFCT & MIRR
CD1 S12 DVD1.2
RREFBF
CB 2
84
RFCT
85
CP 2
86
RFRP
87
RFRPN
88
CB 1
B
8
89
MROFST
A
4
DDVD
CP 1
3
DCD
7
MIRRI
2
6
90
75 BCAO
BCD
BDVD
91
MUX
CCD
CDVD
EQVCC
1
RFEQO
ACD
BCATH
EQGND
to RF EQ TUNING BLOCK
EQIN
AGCLEVEL
92
RFAGCO
AGCB
93
AGCI
AGCP
94
AGCC
RDPF
95
EQF
PLLGF
99 98 97 96
EQG
VZOCTL 100
72 OSC
71 STB S/IF BLOCK
70 CLOCK 69 DATA
68 RREFDLY DPD BLOCK
67 VREFDPD
66 DPDGND
65 TE1RES
GCA
64 PLLCTL
OFSTHOLD TBAL(01H)
TEOFST(04H)
63 DPDMUTE
to DPD BLOCK
62 FAUL TOUT
CDRSEL(OOH) GAIN_ABCD(OOH)
ADVD1 15
61 DPDEQ2 60 DPDEQ1
BDVD1 16 CDVD1 17 DDVD1 18
SUB RF MUX
ACD1 19 BCD1 20
D1 B1 C1 A1
ABCD SUM
EQIN
59 TE30FST
ENV_SEL(02H)
GAIN_FE(03H)
58 BCA 57 MIRR
OFSTHOLD MUX
CCD1 21
ABCD_OFST(O6H)
FE
56 DPDVCC
FE_0FST(05H)
DCD1 22
OFSTHOLD
AVCC 23 VREFA 24
73 RESET
CDRSEL(00H) LDONB(00H)
ANALOG VC AMP
55 DFCT2
MUX
54 DFCT1
TESEL(OOH) ENVELOPE
FOK
53 DFCTTH1
DEFECT
52 DFCTTH2
ALPC
FOFST 25 FOFST
35
36
37 38
39
40
41 42 43
44
45
46
47
48
49
50
VREFLP_BGI
LDODVD
AGND
FE
FEN
TEN
TE
PDLIMITRES
ABCD
ABCDI
ENVP
DGND
FOKTH
FOKB
DFCT_CP1
DFCT_CP2
CC1
CC2
ENV
34
ENVB
33
ABCDN
32
PDCD
28 29 30 31 LDOCD
27
PDVD
26 OFSTHOLD
2-2
51 DVCC
Samsung Electronics
Samsung Electronics
CD optical main beam F input port for SERVO
CD optical main beam F input port for SERVO
Power voltage input port for analog part
CD optical laser monitor diode voltage input port
Power GND port for analog part
FE AMP output port
I
I
P
-/O
O
I
I
O
I
O
I
P
O
CCD1
DCD1
AVCC
VREFA
FOFST
OFSTHOLD
VREFLP_BGI
LDODVD
PDDVD
LDOCD
PDCD
AGND
FE
21
22
23
24
25
26
27
28
29
30
31
32
33
FEN
FOKTH FOKB
45 46
DVCC DVCTTH2
51 52
BCA TE3OFST DPDEQ1 DPDEQ2
58 59 60 61
CD optical laser diode driving voltage output port
DVD optical laser monitor diode voltage input port
DVD optical laser diode driving voltage output port
BANDGAP voltage input port for ALPC
64
63 PLLCTL
DPDMUTE
FAULTOUT
MIRR
57
ON/OFF connection port for auto offset block (L : auto offset adjustment H : serial offset adjustment)
62
DPDVCC
56
center voltage, Use at other block
CAP connection port for focus auto offset (OPEN)
DFCT1 DFCT2
54
DFCTTH1
CC2
50
53
CC1
DFCT_CP2
49
48
DFCT_CP1
DGND
44
47
ENV
ENVB
ENVP
ABCDI
ABCD
ABCDN
PDLIMTRES
TE
TEN
43
42
41
40
39
38
37
36
35
34
PIN NAME
55
CAP connection port for analog part
CD optical main beam F input port for SERVO
I
DVD optical main beam C input port for SERVO
I
BCD1
DVD optical main beam B input port for SERVO
I
20
DVD optical main beam A input port for SERVO
I
CD optical main beam F input port for SERVO
CD optical sub beam F input port for SERVO
I
I
CD optical sub beam E input port for SERVO
I
ACD1
CAP connection port for RF EQ center voltage
O
19
Analog block bias resistance connection port
-
DVD optical main beam D input port for SERVO
RF EQ bias resistance connection port
-
I
RF AMP I/O buffer bias resistance connection port
-
DDVD1
DVD optical main beam D AC coupling input port for RF
I
18
DVD optical main beam C AC coupling input port for RF
I
CDVD1
DVD optical main beam B AC coupling input port for RF
I
17
DVD optical main beam A AC coupling input port for RF
I
BDVD1
CD optical main beam D AC coupling input port for RF
I
16
E
13
CD optical main beam C AC coupling input port for RF
I
F
VREFEQ
12
CD optical main beam B AC coupling input port for RF
I
ADVD1
RREF
11
CD optical main beam A AC coupling input port for RF
I
15
RREFEQ
10
FUNCTION
I/O
14
RREFBF
BDVD
6
9
ADVD
5
CDVD
DCD
4
DDVD
CCD
3
8
BCD
7
ACD
1
2
PIN NAME
BCA output port Resistance connection port for 3BTE offset DPD EQ (A+C) output port DPD EQ (B+D) output port
O O O
I
I
DPD TE PLL variable input port
DPD TE MUTE control port (H : MUTE)
DPD defect waveform output port (MONITOR)
Mirror output port
O
Power voltage input port for DPD TE
P
Defect output port for SERVO
parating level setting
ing level setting Resistance connection port for SERVO defect com-
Resistance connection port for PLL defect comparat-
Power voltage input port for digital circuit
AC coupling input port for defect
Output port of peak detector for defect
min. time setting
(L: FOCUS OK) Peak hold time constant connection port SERVO defect max. time setting Peak hold time constant connection port PLL defect
Focus OK comparator output port
Focus OK comparing level input port
Power GND input port for digital circuit
RF envelope detect output port
95
94
93
92
91
90
AGCP
AGCB
AGCLEVEL
EQGND
AGCI
AGCC
RFAGCO
EQIN
88 89
BCATH
RFEQO
EQVCC
MIRRI
CP1
CB1
MROFST
RFRPN
RFRP
CP2
CB2
RFCT
BCAO
BCAI
87
86
85
84
83
82
81
80
79
78
77
76
75
74
RESET
73
connection port for RF envelope detect
OSC
72
STB
CLOCK
DATA
RREFDLY
VREFDPD
71
Defect output port for PLL
O
TE1RES DPDGND
ABCD AC coupling input port for SERVO monitor
70
69
68
67
66
65
PIN NAME
Peak hold time constant setting RC connection port for RF envelope detect Bottom hold time constant setting RC
ABCD AMP output port
Input port for ABCD AMP GAIN setting
Bias resistance port for PDLIMIT
TE AMP output port
Input port for TE AMP GAIN setting
FE Input port for AMP GAIN setting
FUNCTION
O
O
-
-
P
I
O
-
-
O
I
P
O
-
-
I
O
I
-
O
I
I
I/O
-
-
I
P
I
-
RF peak hold time constant RC connection port for RF AGC
RF bottom hold time constant RC connection port for RF AGC
AGC level control voltage input port
Power GND input port for RF EQ
When AGC is “HOLD”, AGC voltage input port
AGC time constant CAP connection port
RF AGC AMP output port
RFAGCO input port for RF EQ O
BCA comparating level control port I
RF EQ output port
Power voltage input port for RF EQ
Input port for MIRR signal generation
RFCT generation
Peak hold time constant RC connection port for
RFCT generation
Bottom hold time constant RC connection port for
RF ripple offset control port for mirror
RF ripple AMP GAIN input port for mirror
RF ripple AMP output port for mirror
Bottom hold time constant RC connection port for RFCT generation Peak hold time constant RC connection port for RFCT generation
RF ripple center voltage output port for mirror
BCA FILTER2
BCA FILTER1
Reset input port for auto offset block (L : RESET)
OSC time constant input port for auto offset block
Data enable input port
Clock input port
Data input port
Bias resistance connection port for delta block
CAP connection port for DPD TE center
Power GND input port for DPD TE
DPD TE PLL variable bias resistance
FUNCTION
I
O
P
I
-
-
I
I
O
-
-
O
O
I
I
I
I
I
-
O
P
I
I/O
100 VZOCTL
PLLGF
EQF
98 99
EQG
RDPF
97
96
PIN NAME
RF EQ control port (When No. PLLG isn’t adjusted, apply DC CTL voltage.)
RF EQ peak frequency control voltage input port
I
I
RF EQ boost gain control voltage input port
I
RF EQ boost, peak frequency gain control port corresponding to wideband PLL (PLLG. PLLF resistance internal design)
Bias resistance connection port for RF EQ frequency setting
-
I
FUNCTION
I/O
Reference Information
2-3
2-4
EFMOA
EFM
ASYCD
ASYDVD
RFI
EFMI
DVCTL
TBAL
FBAL
SPD
SLD
TRD
FOD
RSTB
COUT
TILTO
FE
EFM ASYMETRY
D/A CONVERTER BLOCK
TRACK COUNTER
ROM
DSP CORE FOR DIGITAL SERVO
PS1
WIDE CAPTURE RANGE PLL
SYSCON INTERFACE BLOCK
SUB CODE READ BLOCK
SSTOP /PSO
TE
TEST
SME
XI
A/D CONVERTER BLOCK
XO
TZCO
XOUT
I/O INTERFACE BLOCK
LOCK
TIMING GENERATOR
SMON
ENV
VREF
PLLHD
INTO_224
FDCTL
MAGICO
EQCTL
VCTRL
RVCO
PLCK
EFMRTD
RPD
PLLLOCK RFD
MDOUT[3:0]
PSB
SENSE
MDATA[7:0]
MRDB
MWRB
CSB
DAB
SCOR
SQSI
SQCK
LDONB
TLKB
FLKB
Reference Information
2-1-3 SIC1 (KS1452 ; Digital Servo)
DIRC
DFCT
FOKB
MIRR
TZCA
PHI1
TILTI
Samsung Electronics
Samsung Electronics
Micom data pin 2
Micom data pin 3
Micom data pin 4
Micom data pin 5
Micom data pin 6
Micom data pin 7
Internal status monitor pin
Servo logic & ROM VDD power supply pin
System clock signal input pin
System clock signal output pin
Clock out (33.9688MHz) to DSP
Servo logic & ROM VSS power supply pin
Clock output pin for subcode data read
Subcode data input pin
Timing detection input pin for subcode data read
Motor ON signal input pin
Lock signal input pin
Direct jump control (for 1 track jump)
I/O
I/O
I/O
I/O
I/O
I/O
O
P
I
O
O
P
O
I
I
I
I
I
XOUT
DVSS
SQCK
SQSI
25
26
27
28
29
DIRC
XO
24
33
XI
23
LOCK
DVDD
22
32
SENSE
21
SCOR
MDATA7
20
SMON
MDATA6
19
31
MDATA5
18
30
MDATA3
MDATA4
17
MDATA2
16
Micom data pin 1
I/O
MDATA1
Micom data pin 0
15
Micom read clock signal input pin
I
I/O
MRDB
Micom write clock signal input pin
I
MWRB
12
MDATA0
Micom data/address select pin
I
DAB
11
14
Micom chip select pin
I
CSB
13
System reset signal input pin
I
RSTB
9
10
1 : 8BIT
0 : 1BIT
I
PSB
8
Tracking servo lock signal output pin
O
TLKB
Focus servo lock signal output pin
O
7
Counter clock
FLKB
Test pin (L : normal H : test)
I
O
6
Sled motor position sensor input pin 1
I
TEST
Limit switch/sled position sensor input pin0
I
COUT
3
Mode data3 out controlled by micom
O
FUNCTION
5
PS1
2
I/O
4
MDOUT3
SSTOP/PSO
1
PIN NAME
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
TE
VREF
SME
AVSS
SVSS
RFI
LPFCD
LPFDVD
EFMO
EFMI
EQCTL
SVDD
TZCO
EFMOA
MAGICO
VCTL
RPD
RFD
RVCO
PVSS
EFMRTD
PLLLOCK
PLCK
PVDD
INTO_224
PLLHD
MIRR
DFCT
LDONB
FDCTL
FOKB
PIN NAME
I
I
I
P
P
I
I
I
O
I
O
P
O
I
I
I
I
I
I
P
O
O
O
P
O
I
I
I
O
I
I
I/O
Tracking error signal input pin
Reference voltage input pin
Spindle error input pin
Analog block VSS power supply pin
Servo CPU VSS power supply pin
RF input signal
Asymmetric input signal for CD
Asymmetric input signal for DVD
EFM signal
EFM signal for test
EQ control signal
Servo CPU VDD power supply pin
Tracking zero cross output pin
EFM offset adjustment pin
Input for hysteresis control of FD output (for test)
Control voltage for VCO
Gain adjust resister for phase detector
Gain adjust resister for frequence detector
Resistor pin for VCO GAIN
PLL logic block VSS power supply pin
Latched EFM output signal
(H : Lock L : Unlock)
Frequency lock detect output
PLCK
PLL logic block VDD power supply pin
Servo interrupt monitor pin
PLL hold signal from micom
Mirror signal input pin
Defect Detection signal input pin
Laser diode ON signal output pin
PLL frequency detect control input pin
Focus OK signal input pin
FUNCTION
72
71
70
69
68
67
66
65
FBAL
TBAL
DVCTL
TILTO
AVDD
TILTI
ENV
FE
PIN NAME
O
O
O
O
P
I
I
I
I/O
Focus balance signal output pin
Tracking balance signal output pin
Depth variation control signal output pin
Tilt out (reserved)
Analog block VDD power supply pin
Tilt in (reserved)
RF envelope input pin
Focus error signal input pin
FUNCTION
TRD TZCA MDOUT0 MDOUT1 MDOUT2
78 79 80
75
77
FOD
74
76
SLD SPD
73
PIN NAME
Mode data 1 out controlled by micom Mode data 2 out controlled by micom
O O
Tracking actuator drive signal output pin
O
TE signal for tracking zero cross input pin
Focus actuator drive signal output pin
O
Mode data 0 out controlled by micom
Spindle motor drive signal output pin
O
O
Sled motor drive signal output pin
O
I
FUNCTION
I/O
Reference Information
2-5
2-6
FG MON MDP MDS FSW PLL_LOCK CLV_LOCK SERVO_LOCK
XTI1 XTO1 CK33MI CK33MO
TO (12)
EFMI PLCK BCARZ
FROM R/F, PLL(3)
CD CLV/CAV
WFCK 17.58/7.35KHz
M
SUBCODE I/F
23BIT SR
CD-G
M
SQ-VCD
DVDP,
MICOM I/F
M
TEST0, TEST1, TEST2
V-CD, CD-DA
DEINTERLEAVE & RAM CONTROL
(6, 4, 3) trans ID ECC
EDC
DESCRAMBLER
TO MICOM (15) MDAT(7:0), MRZA, ZCS, MWR, MRD, ZIRQZD, ZWAIT, ZRST
Power(34)=VDD(11)+GND(23) Test Pin(3)
EFM DEMOD
(32, 28, 5) (28, 24, 5) CIRC
75Hz
676.08Hz
(208, 192, 17) (182, 172, 11) ECC
(6, 4, 3) efmwr ID ECC
16-8 DEMOD
FRAME SYNC DET/PROT/INS (7.35KHz)
VCO TIMING GENERATOR
7.35KHz = 4.3218M/588
17.58KHz = 26.16M/1488
ECSY
Monitor(8) GFS, FRSYZ, TX, EFMO, WFCK, RFCK, CK 16M, DEMPHA
M
DVD CLV/CAV
RFCK 17.58/7.35KHz
X'TAL & TIMING GEN
VCO TIMING GENERATOR
26.16MHz
FRAME SYNC DET/PROT/INS (17.57KHz)
32BIT SR
PWMO(7:0)
TO D-EQ (8)
SDATA[0] / CDATA SDATA[1] / LRCK SDATA[2] / BCLK SDATA[3] / C2PO SDATA[4] / SQDT SDATA[5] / WFSY SDATA[6] / SOS1 SDATA[7] / SQCK DATREQ CSTROBE DTER DATACK TOS
TO AV (13)
DD(15:0) DADR(8:0) ZRAS ZUCAS ZLCAS ZOE(1:0) ZWE(1:0)
TO DRAM 256K*16 (32)
Reference Information
2-1-4 DIC1 (KS1453 ; DVD Data Processor)
Samsung Electronics
Samsung Electronics
DD5_BI
DVSS
DD9_BI
31
32
20
DD10_BI
DD1_BI
19
30
DD14_BI
18
29
DD0_BI
17
DD4_BI
DD15_BI
16
28
DVSS
15
DD11_BI
XTO_OUT
14
27
XTI_IN
13
DVDD
DVDD
12
DD3_BI
MDAT0_BI
11
26
MDAT1_BI
10
25
MDAT2_BI
9
DD12_BI
MDAT3_BI
8
24
MDAT4_BI
7
DD2_BI
MDAT5_BI
6
23
MDAT6_BI
5
DVSS
MDAT7_BI
4
DD13_BI
DVSS
3
21
MRZA_IN
2
22
DVSS
ZCS_IN
1
NAME
PIN
DRAM data bus
Digital GND (0V)
DRAM data bus
DRAM data bus
DRAM data bus
DRAM data bus
Digital power (+5V)
DRAM data bus
DRAM data bus
DRAM data bus
DRAM data bus
Digital GND (0V)
DRAM data bus
DRAM data bus
DRAM data bus
DRAM data bus
Digital GND (0V)
System clock output for 26.16 MHz
System clock input for 26.16 MHz
Digital power (+5V)
Micom data bus
Micom data bus
Micom data bus
Micom data bus
Micom data bus
Micom data bus
Micom data bus
Micom data bus
Digital GND (0V)
(L -> Register H -> Data)
Micom register select
Chip select (Active Low)
Digital GND (0V)
FUNCTION
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
SDATA5_OUT
SDATA4_OUT
SDATA3_OUT
SDATA2_OUT
SDATA1_OUT
SDATA0_OUT
DVDD
DATACK_OUT
TOS_OUT
DVSS
DVSS
DADR3_OUT
DADR4_OUT
DADR2_OUT
DADR5_OUT
DADR1_OUT
DADR6_OUT
DADR0_OUT
DVSS
DADR7_OUT
DADR8_OUT
ZRAS_OUT
ZOEO_OUT
DVDD
ZOE1_OUT
ZWE0_OUT
ZWE1_OUT
ZUCAS_OUT
ZLCAS_OUT
DVSS
DD7_BI
35 36
DD8_BI
DD6_BI
NAME
34
33
PIN
DVD data/Sub code frame sink (WFSY)
DVD data/Sub code serial data (SQDT)
DVD data/CD data error flag (C2P0)
DVD data/CD data bit clock (BLCK)
DVD data/CD data L/R clock (LRCK)
DVD data/CD data bitstream output
Digital power (+5V)
Data acknowledge signal output
Top of sector
Digital GND (0V)
Digital GND (0V)
DRAM address bus
DRAM address bus
DRAM address bus
DRAM address bus
DRAM address bus
DRAM address bus
DRAM address bus
Digital GND (0V)
DRAM address bus
DRAM address bus
DRAM row address strobe
DRAM output enable 0
Digital power (+5V)
DRAM output enable 1 (16M, --------, 16M)
DRAM write enable 0 (4M, 8M, 16M)
DRAM write enable 1 (8M ONLY)
DRAM upper column address strobe
DRAM row column address strobe
Digital GND (0V)
DRAM data bus
DRAM data bus
DRAM data bus
FUNCTION
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
PIN
DVSS
CK33MO_OUT
CK33MI_IN
DVSS
GFS_OUT
TX_OUT
FRSYZ_OUT
DVSS
DVSS
DVSS
DVSS
DVDD
DVDD
DVSS
DVSS
DVSS
PWM00_OUT
PWM01_OUT
PWM02_OUT
PWM03_OUT
DVDD
PWM04_OUT
PWM05_OUT
PWM06_OUT
PWM07_OUT
DVSS
DTER_OUT
DATREQ_IN
CSTROBE_OUT
DVSS
SDATA7_BI
SDATA6_OUT
NAME
Digital GND (+5V)
System clock output for 33.8688MHz
System clock input for 33.8688MHz
Digital GND (0V)
active)
Good frame sync detection result output (“H”
Digital out
Frame sync out
Digital GND (0V)
Digital GND (0V)
Digital GND (0V)
Digital GND (0V)
Digital power (+5V)
Digital power (+5V)
Digital GND (0V)
Digital GND (0V)
Digital GND (0V)
PWM output signal
PWM output signal
PWM output signal
PWM output signal
Digital power (+5V)
PWM output signal
PWM output signal
PWM output signal
PWM output signal
Digital GND (0V)
DVD data error output
Data request from A/V decoder or ROM decoder
Data strobe (clock) output
Digital GND (0V)
DVD data/Sub code serial clock (SQCK)
DVD data/Sub code block sink (S0S1)
FUNCTION
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
PIN
MWR_IN
MRD_IN
ZIRQZD_OUT
ZWAIT_OUT
ZRST_IN
DVSS
BCARZ_IN
DEMPHA_OUT
CK16M_OUT
DVDD
DVDD
DVDD
EFMI_IN
FSW_OUT
FG_IN
MON_OUT
DVSS
DVSS
MDS_OUT
MDP_OUT
SERLOCK_OUT
CLVLOCK_OUT
PLLLOCK_OUT
DVSS
PLCK_IN
RFCK_OUT
WFCK_OUT
EFMO_OUT
TEST2_IN
TEST1_IN
TEST0_IN
NAME
Micom write strobe (schmidt trigger)
Micom read strobe (schmidt trigger)
Interrupt request from micom
Micom read/write access wait (“L” wait)
Hardware reset active low
Digital GND (0V)
BCA input signal
When DEEMPHASIS is ON, “HIGH”.
2∫–¡÷ clock of CK33M/16.934MHz
Digital power (+5V)
Digital power (+5V)
Digital power (+5V)
EFM/EFM+ signal input
Spindle motor output filter conversion output (3state)
Reference signal for CAV
Spindle motor ON/OFF control output
Digital GND (0V)
Digital GND (0V)
Spindle motor speed control signal (3-state)
(3-state)
Spindle motor phase control signal
Lock signal for SERVO
Lock signal for CLV
Lock signal for PLL
Digital GND (0V)
Phase locked clock
Reference frame pulse
Write frame pulse
EFM out
Test mode setting port
Test mode setting port
Test mode setting port
FUNCTION
Reference Information
2-7
Reference Information
2-1-5 DIC2 (KM416C254BJ-6 ; CMOS DRAM) BLOCK DIAGRAM RAS UCAS
Control
LCAS
Clocks
Vcc VBB Generator
Vss
W
Refresh Timer
Row Decoder
Lower Data in Buffer
Refresh Control
Lower
DQ0 to DQ7
Data out Memory Array Refresh Counter
Buffer
262,144 x 16 Upper
Cells
Data in Buffer
Row Address Buffer
AO . .
Upper
OE DQ8 to DQ15
Data out Col. Address Buffer
A8
Column Decoder
FUNCTION
NAME A0-A8 DQ0-15
Address Inputs Data in/Out
VSS
Ground
RAS
Row Address Strobe
UCAS
Upper Column Address Strobe
LCAS
Lower Column Address Strobe
W
Read/Write Input
OE
Data Output Enable
V CC
Buffer
Power (+5V) Power (+3.3V)
N.C
2-8
No Connection
Samsung Electronics
Reference Information
2-1-6 VIC1 (ZiVA-3 ; Audio/Video Decoder) BLOCK DIAGRAM ZiVA-3 Decoder OSD Decoder SDRAM/ EDO/ROM Interface
Memory Controller Subpicture Decoder
Host Interface
Host Interface Control Logic
MPEG Video Decoder
Secure View
CD-DA and LPCM Decoder
CSS Descrambling
Program
DVD/CD Interface
Stream Decoder
Bus Key
Dolby Digital Audio Decoder
Authentication (Optional)
Audio DSP
Video Mixer
Video Interface
Digital Audio Interface
Audio Interface
Scrambled, Compressed Content Descrambled, Compressed Content
MPEG Audio Decoder
Decompressed Content Display Content
LOGIC DIAGRAM DA-DATA[0:3]
CS
Host Interface Signals
DTACKSEL
DA-LRCK
HADDR[2:0]
DA-BCK
Interface
RD
DA-XCK
Signals
DA-IEC
HDATA[7:0] WAIT/DTACK INT
EDO-CAS
HOST8SEL
EDO-RAS
R/W
Video
Audio
LDQM
VDATA[7:0]
MDATA[15:0]
Interface
HSYNC
MADDR[20:0]
Signals
VSYNC
MWE
VCLK
ROM-CS
SDRAM/EDO Interface Signals
SD-CAS DVD-DATA0/CD-DATA
SD-RAS
DVD-DATA1/CD-LRCK
SD-CLK
DVD-DATA2/CD-BCK
SD-CAS[1:0]
DVD-DATA3/CD-C2PO
UDQM
DVD-DATA4/CDG-SDATA
DVD/CD Interface Signals
DVD-DATA5/CDG-VFSY DVD-DATA6/CDG-SOS1
SYSCLK
DVD-DATA7/CDG-SCLK
VDD VSS
VREQUEST
A_VSS
VSTROBE
A_VDD
ERROR
AREQUEST
Samsung Electronics
Interface Signals
P10[10:0]
V-DACK/ASTROBE
A-DACK
Global
RESET
ZiVA Decoder
2-9
Reference Information
2-1-7 VIC50 (SAA7128 ; Digital Video Encoder) BLOCK DIAGRAM LLC1
VDDA
XCLK
TTXRQ
RCV2
RCV1
XTAL
XTALI
SCL
SDA
RESN
25,28,31,36
4
37
8
43
7
34
35
41
42
40
20 VDD I2C 21
I2 C-
SYNC/
INTERFACE
CLOCK
SA
Clock&Timing
I2 C-Control
I2 C-Control
9..16
I2 C-Control
Y
Y MP
MP(7:0)
FADER
CbCr
D
30
CVBS (CSYNC)
27
VBS (CVBS)
24
C (CVBS)
OUTPUT-
ENCODER
C
MP
INTERFACE A
44
I2 C-Control
TTX
22,32,33
I2 C-Control
VSSA
23
Y
D
R(Cr)
RGBCbCr
G(Y)
29
B(Cb)
19 RTC1
AP
SP
FUNCTION
NAME res.
1
3
2
VDD
VSS
I/O
26 A
6,17,39
5,18,38
PIN
PROCESSOR
Reserved pin, do not connect
2
I
SP
Test Pin;connected to digital ground for normal operation
3
I
AP
Test Pin;connected to digital ground for normal operation
4
I
LLC1
Line-Locked Clock input;this is the 27 MHz master clock
5
I
V SS1
Digital supply ground 1
6
I
V DD1
Digital supply 1
7
I/O
RCV1
Raster Contral 1 for video port. This pin receives/provides a VS/FS/FSEQ signal.
8
I/O
RCV2
Raster Contral 2 for video port. This pin provides an HS pulse of programmable length or receives an HS pulse.
2-10
Samsung Electronics
Reference Information
PIN
I/O
9
I
MP7
10
I
MP6
11
I
MP5
12
I
MP4
13
I
MP3
14
I
MP2
15
I
MP1
16
I
MP0
17
I
V DD2
Digital supply voltage 2
18
I
V SS2
Digital ground 2
19
I
RTCI
20
I
21
I
SA
22
I
V SSA1
Analog ground 1 for Red (Cr), C(CVBS), Green(Y) outputs
23
O
R(Cr)
Analog output of Red (Cr)signal
24
O
C
25
I
V DDA1
Analog supply voltage 1 for R(Cr), C(CVBS) outputs
26
O
G(Y)
Analog output of Green(Y) signal
27
O
VBS
Analog output of VBS (CVBS) signal
28
I
V DDA2
Analog supply voltage 2 for VBS(CVBS), Green(Y) outputs
29
O
B(Cb)
Analog output of Blue(Cb) signal
30
O
CVBS
Analog output of CVBS(CSYNC) signal
31
I
V DDA3
Analog supply voltage 3 for Blue(Cb)and CVBS(CSYNC), outputs
32
I
V SSA2
Analog ground 2 for VBS (CVBS), Blue(Cb), CVBS(CSYNC)outputs
33
I
V SSA3
Analog ground 3 for the DAC reference ladder and the oscillator
34
O
XTAL
Crystal oscillator output
35
I
XTAL1
36
I
V DDA4
Analog supply voltage 4 for the DAC reference ladder and the oscillator
37
O
XCLK
Clock output of the crystal oscillator
38
I
V SS3
Digital supply ground 3
39
I
V DD3
Digital supply 3
40
I
RESN
41
I
SCL
12C serial clock input
42
I/O
SDA
12C serial data input/output
43
O
TTXRQ
44
I
TTX
Samsung Electronics
FUNCTION
NAME
VDD
12C
Double speed 54 MHzMPEG port. It is an input for "CCIR 656" style multiplexed Cb, Y, Cr data. Data are sampled on the rising and falling clock edge;data sampled on the risting edge then are sent to the encoding part of the device, data sampled on the falling edge are sent to the RGB part of the device. (or vice verse, depending on programming)
Real Time Control input. If the LLC1 clock is provided by an SAA7111 or SAA7151B, RTCI should be connected to the RTCO pin of the respective decoder to improve the signal quality. Sense input for 12C bus voltage;connect to 12C bus supply Select 12C address; low selects slave address 88h, high selects slave address 8Ch.
Analog output of Chrominance (CVBS) signal
Crystal oscillator input; if the oscillator is not used, this pin should be connected to ground.
Reset input, active LOW. After reset is applied, all digital I/Os are in input mode; PALBlackburst on CVBS, VBS and C;RGB outputs set to lowest voltage. The 12C-bus receiver waits for the START condition.
Teletext Request output, indicating when text bits are requested Teletext bit stream input
2-11
Reference Information
2-1-8 MIC1 (TMP93CM41F ; Main Micom)
PAO~PA6 PA7(SCOUT)
PORT A
VCC[3] VSS[3]
900L-CPU
P50 to P57 (ANO to AN7) AVCC AVSS VREFH VREFL
10-BIT 8CH A/D CONVERTER
XWA XBC ADE XHL XIX XIY XIZ XSP
W B D H
A C E L
(TXD1)P93 (RXD1)P94 (SCLK1)P95
SERIAL I/O
OSC
IX IY IZ SP 32bit
(TXD0)P90 (RXD0)P91 (SCLK0/CTS0)P92
High Frequency
SR
(CH,0) P C
CLK Low
F
Frequency OSC
SERIAL I/O (CH,1)
INTERRUPT
(PG 00)P60 (PG 01)P61 (PG 02)P62 (PG 03)P63 (PG 10)P64 (PG 11)P65 (PG 12)P66 (PG 13)P67
(T10)P70
X1 X2
XT1 XT2 AM8/16 EA RESET ALE TEST2,1
CONTROLLER
NMI
WATCH-DOG
WDTOUT
PATTERN GENERATOR (CH,0) PATTERN
TIMER
GENERATOR (CH,1)
2KB RAM
PORT 0
P00 to P07 (AD0 to AC7)
PORT 1
P10 to P17 (AD8 to AD15/A8 toA15
PORT 2
P20 to P27 (A0 to A7/A16 to A23)
8BIT TIMER (TIMER 0) 8BIT TIMER
(T01)P71
(T02)P72
(TIMER 1)
8BIT PWM (TIMER 2)
(T03)P73
8BIT PWM (TIMER 3) PORT 3
(INT4/T14)P80 (INT5/T15)P81 (T04)P82 (T05)P83 (INT6/T16)P84 (INT7/T17)P85 (T06)P86
16BIT TIMER (TIMER 4)
P30(RD) P31(WR) P32(HWR) P33(WAIT) P34(BUSRQ) P35(BUSAK) P36(R/W) P37(RAS)
16BIT TIMER (TIMER 5)
CS/WAIT CONTROLLER (3-BLOCK)
P40(CS0/CAS0) P41(CS1/CAS1) P42(CX2/CAS2)
(INTO)P87
2-12
Samsung Electronics
Samsung Electronics
MC
AM8
CLK
VCC
GND
X1
X2
/EA
SCLK1
AM8/16
CLK
Vcc
Vss
X1
X2
/EA
/RESET
22
23
24
25
26
27
28
29
30
/MRST
STB
094
21
RF control data
O
MD
TXD1
20
Serial data clock
I
SCLK
SCLKO
Serial data input
19
Serial data output
I
TXD
O
RXD
TXDO
RXDO
Interrupt from DSP
I
ZINT
INTO
16
18
45
Request to front micom
O
RRQ
P86
15
17
44
I
-
INT7
14
Interrupt from spindle motor FG
I
FGINT
/INT6
13
Close switch
I
CLOSE
P83
12
Open switch
I
OPEN
52
RF control clock
Address mode (H: 8 bit mode)
Clock output (System clock÷2)
O
I
O
High frequency OSC out
External access CS41/CS40
O
I
Master reset from FRONT
High frequency OSC in
I
I
56
GND
-
60
59
58
57
55
-
54
53
51
I/O RF data latch
50
49
48
47
46
43
42
41
40
39
P82
Interrupt from front micom
I
38
11
Interrupt from AV-DEC
I
SRQ
Open/close blinking
O
37
36
INT5
AV-DEC H/W reset
O
10
Master clock select
O
35
34
LED
DSP H/W reset
DVDINT
Non-maskable interrupt
I
O
33
P73
A/D VCC input
-
32
31
/INT4
A/D GND input
No
9
A/D Ref input (L)
I
-
FUNCTION
8
MCK_SEL
ZIVA_RST
P70
5
P71
/NMI
4
P72
-
ZRST
AVcc
3
7
AVCC
AVss
2
6
GND
AGND
VREFL
1
ASSIGNED I/O NAME
PORT NAME
No
A15
A14
A13
A12
A11
A10
A9
A8
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
Vcc
ALE
PA7
PA6
PA5
PA4
PA3
PA2
PA1
PA0
TEST2
TEST1
P97
P96
PORT NAME
HA15
HA14
HA13
HA12
HA11
HA10
HA9
HA8
HAD7
HAD6
HAD5
HAD4
HAD3
HAD2
HAD1
HAD0
VCC
ALE
-
-
-
-
-
EWC
EDT
ECK
TEST2
TEST1
XT2
XT1
EEPROM CLOCK
Test pin. connect to TEST1
Test pin. connect to TEST2
-
-
FUNCTION
Address latch enable
EEPROM WRITE PROTECT
O
O
O
O
O
O
O
O
Address 15
Address 14
Address 13
Address 12
Address 11
Address 10
Address 9
Address 8
I/O Address/Data 7
I/O Address/Data 6
I/O Address/Data 5
I/O Address/Data 4
I/O Address/Data 3
I/O Address/Data 2
I/O Address/Data 1
I/O Address/Data 0
-
O
O
O
O
O
O
O
I/O EEPROM DATA I/O
O
-
-
O
O
ASSIGNED I/O NAME
/CS1
P40/CS0
80 81
P37
P36
P35
P34
/WAIT
P32
/WR
/RD
A23
A22
A21
A20
A19
A18
A17
A16
Vcc
VSS
/WDTOUT
PORT NAME
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
No
/CS1
-
-
-
-
RCODE
/MWAIT
-
/WR
/RD
HA23
HA22
HA21
HA20
HA19
HA18
HA17
HA16
VCC
GND
WDTOUT
Address 18 (Data processor) Address 19 Address 20 (D. SERVO) Address 21 Address 22 Address 23 /Read strobe /Write strobe
O O O O O O O O
98 99 100
O I/O O
-
97
I/O
Chip select 1 (SRAM, 1M Bit, 128KB)
96
95
I I/O
94
93
92
91
90
89
88
87
86
I/O /Wait
Address 17 (AV-DECODER)
O 85
84
Address 16
O
82
No
83
Watch dog timer output
FUNCTION
-
-
O
ASSIGNED I/O NAME
VREFH
P57
P56
P55
P54
P53
P52
P51
P50
Vss
P67
P66
P65
P64
P63
P62
P61
P60
/CS2
PORT NAME
AVCC
VREFO
RFO
RFRP1
FOKB
SENSE
FR
TILTO
SLOCK
GND
RSTB
CSB
DAB
SDA
SCL
TRAY-OUT
TRAY-IN
-
/CS2
IIC clock (VIDEO ENCODER)
Tray out control output
Tray in control output
Chip slect 2 (EPROM, 4M Bit, 512KB)
FUNCTION
I
I
I
I
I
I
I
I
-
O
O
O
A/D Ref input (H)
RF sum signal
Tracking lock monitor from SERVO
Focus lock monitor from RF
SENSE monitor from SERVO
Spindle direction from SP driver
Monitor signal
LOCK monitor from DSP
D.Servo IC reset
D.Servo IC chip select
D.Servo IC data/Address select
I/O IIC clock (VIDEO ENCODER)
O
O
O
I/O
O
ASSIGNED I/O NAME
Reference Information
2-13
Reference Information
2-1-9 MIC8 (M27C801 ; 8MB (1M x 8-bit) CMOS EPROM) BLOCK DIAGRAM
Data Outputs DQ0-DQ7
Vcc Vss OE/VPP
Output Enable Chip Enable and Prog Logic
CE
Y Decoder A0-A19 Address Inputs
X Decoder
Output Buffers
Y Gating
. .
. . . . .
2,097,152-Bit Cell Matrix
TOP VIEW
2-14
A19
1
32 Vcc
A16
2
31 A18
A15
3
30 A17
A12
4
29 A14
A7
5
28 A13
A6
6
27 A8
A5
7
26 A9
A4
8
25 A11
A3
9
NAME
FUNCTION
A0-A19
Address Inputs
CE
Chip Enable Input
DQ0-DQ7
Data Input/Outputs
OE
Output Enable Input
24 OE/VPP
Vcc
Vcc Syply Voltage
A2 10
23 A10
Vss
A1 11
22 CE
A0 12
21 DQ7
DQ0 13
20 DQ6
DQ1 14
19 DQ4
DQ2 15
18 DQ4
Vss 16
17 DQ3
Ground
Samsung Electronics
Samsung Electronics
TEST1
*RES
XT1
11
12
13
VDD
AN0/P80
AN1/P81
AN2/P82
AN3/P83
AN4/P84
AN5/P85
AN6/P86
AN7/P87
P70/INT0
P71/INT1
P72/INT2
P73/INT3
18
19
20
21
22
23
24
25
26
27
28
29
30
CF2
P27
17
P26
9
10
CF1
P25
8
16
P24
7
XT2
P23
6
VSS
P22
5
15
DIF2
P21
4
14
DIF1
P20
3
REMOCON
-
-
RRQ
MODE4
MODE3
MODE2
MODE1
MODE0
-
MIC_DET
ECHO_VR
VDD
-
-
GND
-
GND
-
DARST1
DIF0
DARST
DEMO1
DEMO0
DFS
-
MRST
P52
PWM1
2
D/A Control
D/A Control
D/A Control
D/A Control
D/A Control
D/A Control
O
O
O
O
O
O
HARDWARE MODE SELECT
HARDWARE MODE SELECT
HARDWARE MODE SELECT
Request to front micom
I
I
I
I 58 59 60
I
I
57
56
55
54
I
REMOCON data in
HARDWARE MODE SELECT
I 53
52
HARDWARE MODE SELECT
I
50 51
MIC detect
I
49
48
47
46
45
44
I
ECHO volume A/D input
I
High frequency OSC out
High frequency OSC in
Low frequency OSC out
43
42
Low frequency OSC in
41
I
40
39
38
37
36
35
-
Reset
D/A Control
O 34
33
D/A Control
O
31
No
32
Front end reset
FUNCTION
-
O
ASSIGNED I/O NAME
1
PORT NAME
No
S27
S26
S25
S24
S23
S22
S21
S20
S19
S18
S17
S16
VP
VDD
S15/T15
S14/T14
S13/T13
S12/T12
S11/T11
S10/T10
S9/T9
S8/T8
S7/T7
S6/T6
S5/T5
S4/T4
S3/T3
S2/T2
S1/T1
S0/T0
PORT NAME GRID8
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
-28V
+5V
SEG17
SEG18
SEG19
SEG20
SEG21
-
-
-
GRID1
GRID2
GRID3
GRID4
GRID5
GRID6
GRID7
FLT SEGMENT CONTROL FLT SEGMENT CONTROL FLT SEGMENT CONTROL FLT SEGMENT CONTROL
O O O O
FLT SEGMENT CONTROL FLT SEGMENT CONTROL
O
FLT SEGMENT CONTROL
O O
FLT SEGMENT CONTROL FLT SEGMENT CONTROL
O
FLT SEGMENT CONTROL
O O
FLT SEGMENT CONTROL
O
FLT SEGMENT CONTROL 80
79
78
O
-
76 77
FLT SEGMENT CONTROL
O
75
74
-
FLT SEGMENT CONTROL FLT SEGMENT CONTROL
O
FLT SEGMENT CONTROL
O O
72 73
71 FLT SEGMENT CONTROL
70
69
68
67
66
65
64
63
62
61
No
O
FLT GRID CONTROL
FLT GRID CONTROL
FLT GRID CONTROL
FLT GRID CONTROL
FLT GRID CONTROL
FLT GRID CONTROL
FLT GRID CONTROL
FLT GRID CONTROL
FUNCTION
O
O
O
O
O
O
O
O
O
O
O
ASSIGNED I/O NAME
P17/PWMO
P16/BUZ
P15/SCK1
P14/S11
P13/S01
P12/SCK0
P11/S10
P10/S00
P07
P06
P05
P04
P03
P02
P01
P00
S31
S30
S29
S28
PORT NAME
-
-
-
-
SCLK
RXD
TXD
SRQ
-
-
-
GND
KEY2
KEY1
KEY0
SEG1
SEG2
SEG3
SEG4
P35 P36 P37 VSS VDD
87 88 89 90
I O O
TV TYPE TV TYPE
I I
FRONT MUTE STANDBY LED POWER ON/OFF CONTROL
O O O
AMUTE1 AMUTE0 LED ON/OFF
P43 P44 P45 P46 P47 P50 P51
94 95 96 97 98 99 100
SERIAL DATA IN SERIAL CLOCK
I
SCART CONTROL
O
AMUTE2
AMUTE3
WIDE
-
SCART CONTROL SUB WOOPER MUTE CENTER MUTE REAR MUTE
O O O O
O P42
93
SERIAL DATA OUT
O
SCART CONTROL O P41
92
SCON_B
P40
91
O
-
Request to MAIN Micom
RGBCTL
JOG DATA
I
-
SHUTTLE DATA JOG DATA
I
SHUTTLE DATA
I I
SHUTTLE DATA
I
FUNCTION SHUTTLE DATA
I
O
GND
+5 V
AD
AT
J2
J1
S4
S3
S2
S1
ASSIGNED I/O NAME
O
KEY SCAN
I
86
KEY SCAN
I
P34
85
KEY SCAN
P33
I
P32
84
FLT SEGMENT CONTROL
O
83
FLT SEGMENT CONTROL
O
P31
82
FLT SEGMENT CONTROL
O
P30
81
FLT SEGMENT CONTROL
O
PORT NAME
FUNCTION No
ASSIGNED I/O NAME
Reference Information
2-1-10 FIC2 (LC866232 ; Front Micom)
2-15
Reference Information
MEMO
2-16
Samsung Electronics
3. Product Specifications NTSC
GENERAL
Power Requirements
AC 120V, 60Hz
Power Consumption
DVD-909 ; 19W,
Weight Dimensions Operating Temperature Range Operating Humidity Range DVD (Digital Versatile Disc) CD : 5 inches
DISC
DVD-709 ; 17W
7.5lbs W 16.9 in X D 11.0 in X H 3.5 in +41°F ~ +95°F 10% to 75% Reading Speed : 11.45 ft/sec. Approx. Play Time (Single Sided, Single Layer Disc) : 135 min. Reading Speed : 3.9 to 4.6 ft/sec.
(Compact Disc)
Maximum Play Time : 74min.
CD : 31/2 inches
Reading Speed : 3.9 to 4.6 ft/sec.
(Compact Disc)
Maximum Play Time : 20min.
VCD : 5 inches Composite Video
Reading Speed : 3.9 to 4.6 ft/sec. Maximum Play Time : 74min. (Video + Audio) DVD-909 ; 2 channel : 1.0Vp-p (75ohm load)
DVD-709 ; 1 channel : 1.0Vp-p (75ohm load)
Y : 1.0Vp-p (75ohm load) ;
Video Output
RCA-Jack
Pr : 0.70Vp-p (75ohm load) ; Pb : 0.70Vp-p (75ohm load) ;
S-Video Mixed Audio Out Analog Audio Out
Luminance Signal : 1Vp-p (75ohm load) Color Signal : 0.286Vp-p (75ohm load) DVD-709 : L, R DVD-909 : L1/L2, R1/R2 F/L, F/R, R/L, R/R, C/T, S/W ; DVD-909 Only Analog : 2Vrms (1KHz, odBFS)
Output Level
Digital : DVD-709 ; 500mVp-p (Coaxial)
Audio Output
DVD-909 ; 500mVp-p (Coaxial), 1.15Vp-p (Optical) * Frequency Response
48KHz Sampling : 4Hz to 22 KHz 96KHz Sampling : 4Hz to 44KHz
* S/N Ratio
110dB
* Dynamic Range
96dB
* Total Harmonic Distortion
0.003% * : Nominal specification
Samsung Electronics
3-1
Product Specification
PAL
GENERAL
Power Requirements
AC 110V ~ 240V, 50/60Hz
Power Consumption
DVD-909 ; 19W,
Weight Dimensions
W 430mm X D 280mm X H 89mm +5°C ~ 35°C
Operating Humidity Range
10% ~ 75%
(Digital Versatile Disc) CD : 12cm DISC
3.4Kg
Operating Temperature Range DVD
(Compact Disc) CD : 8cm (Compact Disc) VCD : 12cm
DVD-709 ; 17W
Reading Speed : 3.49m/sec. Approx. Play Time (Single Sided, Single Layer Disc) : 135 min. Reading Speed : 1.2 to 1.4m/sec. Maximum Play Time : 74min. Reading Speed : 1.2 to 1.4m/sec. Maximum Play Time : 20min. Reading Speed : 1.2 to 1.4m/sec. Maximum Play Time : 74min. (Video + Audio) R (Red) : 0.714Vp-p (75ohm load)
Scart Jack (Option)
G (Green) : 0.714Vp-p (75ohm load) B (Blue) : 0.714Vp-p (75ohm load) Composite Video : 1.0Vp-p (75ohm load)
Video Output
Composite Video - DVD-909 ; 2 channel : 1.0Vp-p (75ohm load) DVD-709 ; 1 channel : 1.0Vp-p (75ohm load) Component Video
Y : 1.0Vp-p (75ohm load) ;
RCA-Jack (Option)
Pr : 0.70Vp-p (75ohm load) ; Pb : 0.70Vp-p (75ohm load) ;
RCA-Jack S-Video Scart Jack RCA-Jack
Component Video Channel : 1.0Vp-p (75ohm load) ; 2 Channel : 1.0Vp-p (75ohm load) ; Luminance Signal : 1Vp-p (75ohm load) Color Signal : 0.286Vp-p (75ohm load) 2 Channel : L, R 2 Channel : L (1/L), R (2/R) 5.1 Channel : F/L, L/R, R/L, R/R, C/T, S/W - (DVD-909 Only) Analog : 2Vrms (1KHz, 0dBFS)
Output Level
Digital : DVD-709 ; 500mVp-p (Coxial)
Audio Output
DVD-909 ; 500mVp-p (Coxial), 1.15Vp-p (Optical) * Frequemvy Response
48KHz Sampling : 4Hz to 22KHz 96KHz Sampling : 4Hz to 44KHz
* S/N Ratio
110dB
* Dynamic Range
96dB
* Total Harmonic Distortion
0.003%
* : Nominal specification 3-2
Samsung Electronics
Samsung Electronics
PHONE
MIN
LEVEL
MAX
ADVANCED DOLBY DIGITAL DECODER BUILT-IN
POWER
STANDBY
OPEN/ OPEN/ OPEN/ CLOSE CLOSE CLOSE
DVD-909
DVD/VIDEO-CD/CD PLAYER DVD-909
Description-Front Panel
SKIP
SPATIALIZER N-2-2 DIGITAL VIDEO
DVD/VIDEO-CD/CD PLAYER DVD-709 OPEN/ OPEN/ CLOSE CLOSE
SPATIALIZER N-2-2
SKIP
DIGITAL VIDEO
• When the unit is first plugged in, the indicator lights. When power is pressed on, the lamp goes out.
DISC OPERATION ROTARY INDICATOR OPERATION INDICATOR DISC TYPE INDICATOR TRACK INDICATOR 3D SOUND INDICATOR ANGLE INDICATOR CHAPTER INDICATOR REPEAT INDICATOR CHAPTER, TITLE, TRACK & MESSAGE INDICATOR ALL REPEAT INDICATOR A-B REPEAT INDICATOR PROGRAM PLAY INDICATOR MPEG INDICATOR DOLBY DIGITAL INDICATOR LINEAR PCM INDICATOR DTS INDICATOR
Front Display
24bit 96kHz AUDIO D/A CONVERTER
POWER
• Use to turn the power on and off.
HEADPHONES JACK • You can attach headphones here for private listening. HEADPHONES VOLUME • Use to adjust headphones volume level. DISPLAY (See below) • Operation indicators are displayed here. DISC TRAY • Press OPEN/CLOSE to open and close the disc tray. GREEN LAMP SKIP/SEARCH • Use to skip or search a scene or music. OPEN/CLOSE • Press to open and close the disc tray. PLAY/PAUSE • Begin or pause disc play. JOG DIAL • Operates frame by frame playback. In CD mode, performs track search. SHUTTLE DIAL • Performs fast or slow motion playback. STOP • Stops disc play.
DISC OPERATION ROTARY INDICATOR OPERATION INDICATOR DISC TYPE INDICATOR TRACK INDICATOR 3D SOUND INDICATOR ANGLE INDICATOR CHAPTER INDICATOR REPEAT INDICATOR CHAPTER, TITLE, TRACK & MESSAGE INDICATOR ALL REPEAT INDICATOR A-B REPEAT INDICATOR PROGRAM PLAY INDICATOR MPEG INDICATOR DOLBY DIGITAL INDICATOR LINEAR PCM INDICATOR DTS INDICATOR
Front Display
STOP • Stops disc play.
PLAY/PAUSE • Begin or pause disc play.
OPEN/CLOSE • Press to open and close the disc tray.
SKIP/SEARCH • Use to skip or search a scene or music.
GREEN LAMP
DISC TRAY • Press OPEN/CLOSE to open and close the disc tray.
• Operation indicators are displayed here.
DISPLAY (See below)
POWER
• Use to turn the power on and off.
POWER
STANDBY LAMP
Front Panel Controls
• When the unit is first plugged in, the indicator lights. When power is pressed on, the lamp goes out.
STANDBY
DVD-709
STANDBY LAMP
Front Panel Controls
Description-Front Panel
4. Operating Instructions
4-1 NTSC (DVD-909/709)
4-1
4-2
L
L
R
L
• Connect to the Audio input jacks of your television, audio/video receiver, or VCR.
MIXED AUDIO OUT JACKS
• Use these jacks if you have a TV with component video in jacks. These jacks provide Pr, Pb and Y video. Along with SVideo, Component Video provides the best picture quality.
COMPONENT VIDEO OUT JACKS
• Use the S-Video cable to connect this jack to the S-Video jack on your television for a higher quality picture.
• Connect to the Audio input jacks of your television, audio/video receiver, or VCR.
• Connect to an amplifier with 5.1ch analog input jacks.
S-VIDEO OUT JACK
ANALOG AUDIO OUT JACKS
• Use the S-Video cable to connect this jack to the S-Video jack on your television for a higher quality picture.
S-VIDEO OUT
S-VIDEO OUT JACK
VIDEO OUT
5.1CH ANALOG AUDIO OUT JACKS
ANALOG AUDIO OUT
• Use a video cable to connect this jack to the Video input on your television.
Rear Panel
DIGITAL AUDIO OUT
VIDEO OUT JACK
COMPONENT VIDEO OUT
Y
• Use a coaxial digital cable to connect to an A/V Amplifier that contains a Dolby Digital decoder or DTS decoder.
S-VIDEO OUT
Pr
Pb
DIGITAL AUDIO OUT JACK
VIDEO OUT
V2
V1
• Use a video cable to connect one of these jacks to the Video input on your television.
L2
L1
DVD-709
VIDEO OUT JACKS
MIXED AUDIO OUT
R2
R1
Description-Rear Panel
• Use either an optical or coaxial digital cable to connect to a compatible Dolby Digital receiver. Use to connect to an A/V Amplifier that contains the Dolby Digital decoder or DTS decoder.
S/W
CENTER
ANALOG AUDIO OUT
FRONT
SURROUND
R
R
DVD-909
DIGITAL AUDIO OUT JACK
Rear Panel
COAXIAL
DIGITAL AUDIO OUT
OPTICAL
Description-Rear Panel
Operating Instructions
Samsung Electronics
A Tour of the Remote Control
Samsung Electronics • Use to mark a segment to repeat between A and B.
SUBTITLE Button A-B REPEAT Button
• Use to access various camera angles on a DVD.
ANGLE Button
• This button functions as a toggle switch.
ENTER/DIRECTION Button (UP/DOWN or LEFT/RIGHT Button)
• Brings up the Disc menu.
MENU Button
• Displays the current disc mode.
DISPLAY Button
• Allows you to program a specific order.
MODE Button
• Use to remove menus or status displays from the screen.
CLEAR Button
• Use to skip the title, chapter, or track.
NOTE
This
icon indicates an invalid button press.
• Before connecting, set headphone volume at minimum. Then adjust to a suitable volume.
Connect headphones with a standard stereo plug to the headphone jack (M6).
• Check if there is any fluorescent lighting nearby.
• Check if remote sensor is blocked by obstacles.
• Check if the batteries are drained.
• Begin/Pause disc play.
SKIP Buttons
• Check the polarity + - of the batteries (Dry-Cell)
To Connect Headphones (not included) (DVD-909 only)
Replace the battery cover.
Insert two AA batteries. Make sure that the polarities (+ and -) are aligned correctly.
Open the battery cover on the back of the remote.
If remote doesn’t operate properly:
3.
1. 2.
Install Batteries in the Remote
VOLUME UP/DOWN Buttons
CHANNEL UP/DOWN Buttons
3D SOUND Button BOOKMARK Button PLAY/PAUSE Button
• To control the master volume of the player.
VOLUME CON. Button
• Use to set the remote to control a compatible TV.
TV POWER Button
• Allows you to repeat play a title, chapter, track, or disc.
REPEAT Button
• Use this button to access various audio functions on a disc.
AUDIO Button
• Accesses a music or video display directly.
TOP MENU Button
• Returns to a previous menu.
RETURN Button
• Advances playback one frame at a time.
STOP Button STEP Button
• Allows you to search forward/backward through a disc.
ZOOM Button SEARCH Buttons
• Brings up the DVD player’s Setup menu.
TV POWER Button
DVD POWER Button NUMBER Buttons OPEN/CLOSE Button SETUP Button
TV/VIDEO Selection Button
TV Function Buttons
DVD Function Buttons
A Tour of the Remote Control (Cont’d)
Operating Instructions
4-3
4-4
DVD-909
DVD PLAYER
TV
Better picture
Good picture
Basic Audio
V2
V1
OR OR
S-Video Cable (included)
S-Video Jack
S-VIDEO OUT
L2
L1
AV Cable (included)
Video Input Jack
Method 2
Y
Y
Best picture
COMPONENT VIDEO OUT
Pr
Pb
Pb
Pr
Component Video Jacks
Method 3
Video Cables (not included)
• Method 3 DVD Player + TV with Component Video Jacks
• Method 2 DVD Player + TV with S-Video Input Jack
VIDEO OUT
L
Method 1
Connecting to a TV (For Video)
• Method 1 DVD Player + TV with Video Input Jack
MIXED AUDIO OUT
R2
R1
R
Audio Input Jacks
TV (Normal, Widescreen, Projection, etc..)
Connecting to a TV
• Refer to owner’s manual of the components you are connecting for more information on those particular components.
• Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
Before Connecting the DVD Player
The following show examples of connections commonly used to connect the DVD player with a TV and other components.
Choosing a Connection
L2
L1
COAXIAL DIGITAL AUDIO OUT
OPTICAL
R
R
L
L
S/W
CENTER
ANALOG AUDIO OUT
SURROUND
FRONT
Rear Panel
Mixed Audio Out
MIXED AUDIO OUT
R2
R1
L
R1
L1
V1
MIXED AUDIO OUT
R2
L2
VIDEO OUT
V2
L
L
S/W
CENTER
ANALOG AUDIO OUT
SURROUND
S-VIDEO OUT
Y
COMPONENT VIDEO OUT
Pr
Pb
COAXIAL
COAXIAL
Connecting to an Audio System
Digital Audio Out
DIGITAL AUDIO OUT
OPTICAL
OR
OPTICAL
Digital Audio Input Jacks
Dolby Digital Decoder
Method 3
• Method 3 DVD Player + Amplifier with Dolby Digital Decoder/DTS Decoder
• Method 2 DVD Player + Amplifier with 5.1ch Analog Input Jacks
• Method 1 DVD Player + 2ch Stereo Amplifier or Dolby Pro Logic Decoder
Subwoofer
Center
Analog Audio Out
R
FRONT
Rear (LH)
Rear (RH)
R
Front (LH)
Front (RH)
Audio Input Jacks
R
5.1ch Analog Amplifier
2ch Amplifier
Method 2
Audio Input Jacks
Method 1
Connecting to an Audio System
Choosing a Connection (Cont’d)
DVD PLAYER
AUDIO SYSTEM
Operating Instructions
Samsung Electronics
DVD-709
Samsung Electronics
DVD PLAYER
TV
S-VIDEO OUT
Best picture
Basic Audio
OR
S-Video Cable (included)
VIDEO OUT
AV Cable (included)
Method 2 S-Video Jack
Better picture
L
L
Video Input Jack
Method 1
• Method 2 DVD Player + TV with S-Video Input Jack
• Method 1 DVD Player + TV with Video Input Jack
Connecting to a TV (For Video)
ANALOG AUDIO OUT
R
R
Audio Input Jacks
TV (Normal, Widescreen, Projection, etc..)
Connecting to a TV
• Refer to owner’s manual of the additional components you are connecting for more information for those particular components.
• Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
Before Connecting the DVD Player
The following show examples of connections commonly used to connect the DVD player with a TV and other components.
Choosing a Connection
DIGITAL AUDIO OUT
Rear Panel
R
L
ANALOG AUDIO OUT
VIDEO OUT
S-VIDEO OUT
DVD PLAYER
AUDIO SYSTEM
• Method 2 DVD Player + Amplifier with Dolby Digital Decoder/DTS Decoder
• Method 1 DVD Player + 2ch Stereo Amplifier or Dolby Pro Logic Decoder
Connecting to an Audio System
Digital Audio Out
ANALOG AUDIO OUT
Analog Audio Out
L
DIGITAL AUDIO OUT
R
L
Digital Audio Input Jack
Audio Input Jacks R
Dolby Digital Decoder
Method 2
2ch Amplifier
Method 1
Connecting to an Audio System
Choosing a Connection (Cont’d)
Operating Instructions
4-5
4-6
PHONE
MIN
LEVEL
MAX
ADVANCED DOLBY DIGITAL DECODER BUILT-IN
POWER
STANDBY
DVD/VIDEO-CD/CD PLAYER DVD-909
Description-Front Panel
OPEN/ OPEN/ OPEN/ CLOSE CLOSE CLOSE
DVD-909
SKIP
SPATIALIZER N-2-2 DIGITAL VIDEO
DVD/VIDEO-CD/CD PLAYER DVD-709 OPEN/ OPEN/ CLOSE CLOSE
SPATIALIZER N-2-2
SKIP
DIGITAL VIDEO
• When the unit is first plugged in, the indicator lights. When power is pressed on, the lamp goes out.
DISC OPERATION ROTARY INDICATOR OPERATION INDICATOR DISC TYPE INDICATOR TRACK INDICATOR 3D SOUND INDICATOR ANGLE INDICATOR CHAPTER INDICATOR REPEAT INDICATOR CHAPTER, TITLE, TRACK & MESSAGE INDICATOR ALL REPEAT INDICATOR A-B REPEAT INDICATOR PROGRAM PLAY INDICATOR PAL INDICATOR MPEG INDICATOR DOLBY DIGITAL INDICATOR LINEAR PCM INDICATOR DTS INDICATOR
Front Display
24bit 96kHz AUDIO D/A CONVERTER
POWER
• Use to turn the power on and off.
HEADPHONES JACK • You can attach headphones here for private listening. HEADPHONES VOLUME • Use to adjust headphones volume level. DISPLAY (See below) • Operation indicators are displayed here. DISC TRAY • Press OPEN/CLOSE to open and close the disc tray. GREEN LAMP SKIP/SEARCH • Use to skip or search a scene or music. OPEN/CLOSE • Press to open and close the disc tray. PLAY/PAUSE • Begin or pause disc play. JOG DIAL • Operates frame by frame playback. In CD mode, performs track search. SHUTTLE DIAL • Performs fast or slow motion playback. STOP • Stops disc play.
DISC OPERATION ROTARY INDICATOR OPERATION INDICATOR DISC TYPE INDICATOR TRACK INDICATOR 3D SOUND INDICATOR ANGLE INDICATOR CHAPTER INDICATOR REPEAT INDICATOR CHAPTER, TITLE, TRACK & MESSAGE INDICATOR ALL REPEAT INDICATOR A-B REPEAT INDICATOR PROGRAM PLAY INDICATOR PAL INDICATOR MPEG INDICATOR DOLBY DIGITAL INDICATOR LINEAR PCM INDICATOR DTS INDICATOR
Front Display
STOP • Stops disc play.
PLAY/PAUSE • Begin or pause disc play.
OPEN/CLOSE • Press to open and close the disc tray.
SKIP/SEARCH • Use to skip or search a scene or music.
GREEN LAMP
DISC TRAY • Press OPEN/CLOSE to open and close the disc tray.
• Operation indicators are displayed here.
DISPLAY (See below)
POWER
• Use to turn the power on and off.
POWER
STANDBY LAMP
Front Panel Controls
• When the unit is first plugged in, the indicator lights. When power is pressed on, the lamp goes out.
STANDBY
DVD-709
STANDBY LAMP
Front Panel Controls
Description-Front Panel
Operating Instructions
4-2 PAL (DVD-909/709)
Samsung Electronics
Samsung Electronics
L
L
R
• Use a video cable to connect one of these jacks to the Video input on your television.
VIDEO OUT JACKS
• Connect to the Audio input jacks of your television, audio/video receiver, or VCR.
MIXED AUDIO OUT JACKS • Connect to a video recorder or other equipment.
SCART AV2 JACK
• Connect to a TV with scart input jack.
SCART AV1 JACK • Use a video cable to connect this jack to the Video input on your television.
VIDEO OUT JACK
• Connect to the Audio input jacks of your television, audio/video receiver, or VCR.
• Connect to an amplifier with 5.1ch analog input jacks.
L
ANALOG AUDIO OUT
ANALOG AUDIO OUT JACKS
5.1CH ANALOG AUDIO OUT JACKS
DIGITAL AUDIO OUT JACK
Rear Panel
DIGITAL AUDIO OUT
• Use the switch to set TV system.
AV2
AV1
TV SYSTEM SELECT SWITCH
S-VIDEO OUT
TV SYSTEM SELECT
PAL
SECAM
NTSC
• Use a coaxial digital cable to connect to an A/V Amplifier that contains a Dolby Digital decoder or DTS decoder.
VIDEO OUT
V2
V1
• Use the S-Video cable to connect this jack to the S-Video jack on your television for a higher quality picture.
L2
L1
DVD-709
S-VIDEO OUT JACK
MIXED AUDIO OUT
R2
R1
Description-Rear Panel
• Use either an optical or coaxial digital cable to connect to a compatible Dolby Digital receiver. Use to connect to an A/V Amplifier that contains the Dolby Digital decoder or DTS decoder.
S/W
CENTER
ANALOG AUDIO OUT
FRONT
SURROUND
R
R
DVD-909
DIGITAL AUDIO OUT JACK
Rear Panel
COAXIAL
DIGITAL AUDIO OUT
OPTICAL
Description-Rear Panel
SCART JACK
VIDEO OUT
TV SYSTEM SELECT
PAL
SECAM
NTSC
AV
• Connect to a TV with scart input jack.
SCART AV JACK
• Use the switch to set TV system.
TV SYSTEM SELECT SWITCH
• Use the S-Video cable to connect this jack to the S-Video jack on your television for a higher quality picture.
S-VIDEO OUT JACK
S-VIDEO OUT
Operating Instructions
4-7
4-8
FRONT
L
VIDEO OUT S-VIDEO OUT
V2
V1
Pr
Y
COMPONENT VIDO OUT
Pb
TV SYSTEM SELECT
TV SYSTEM SELECT SWITCH • Use the switch to set TV system.
• Connect to an amplifier with 5.1ch analog input jacks.
MIXED AUDIO OUT JACKS
• Connect to the Audio input jacks of your television, audio/video receiver, or VCR.
COMPONENT VIDEO OUT JACKS • Use these jacks if you have a TV with Component Video in jacks. These jacks provide Pr, Pb and Y video. Along with SVideo, Component Video provides the best picture quality.
• Use a video cable to connect one of these jacks to the Video input on your television.
VIDEO OUT JACKS
5.1CH ANALOG AUDIO OUT JACKS
Rear Panel
L
• Use a video cable to connect this jack to the Video input on your television.
VIDEO OUT JACK
• Connect to the Audio input jacks of your television, audio/video receiver, or VCR.
ANALOG AUDIO OUT JACKS
• Use a coaxial digital cable to connect to an A/V Amplifier that contains a Dolby Digital decoder, MPEG-2 decoder or DTS decoder.
DIGITAL AUDIO OUT JACK
ANALOG AUDIO OUT
VIDEO OUT
S-VIDEO OUT
• Use the switch to set TV system.
TV SYSTEM SELECT SWITCH
• Use the S-Video cable to connect this jack to the S-Video jack on your television for a higher quality picture.
S-VIDEO OUT JACK
TV SYSTEM SELECT
PAL
NTSC
PAL
SECAM
R
DVD-709
SECAM
DIGITAL AUDIO OUT
Description-Rear Panel
NTSC
• Use the S-Video cable to connect this jack to the S-Video jack on your television for a higher quality picture.
L2
L1
S-VIDEO OUT JACK
MIXED ADUIO OUT
R2
R1
• Use either an optical or coaxial digital cable to connect to a compatible Dolby Digital receiver. Use to connect to an A/V Amplifier that contains the Dolby Digital decoder, MPEG-2 decoder or DTS decoder.
SW
CENTER
ANALOG AUDIO OUT
R SURROUND L
R
DVD-909
DIGITAL AUDIO OUT JACK
Rear Panel
DIGITAL AUDIO OUT
OPTICAL COAXIAL
Description-Rear Panel
COMPONENT VIDEO RCA JACK
Operating Instructions
Samsung Electronics
A Tour of the Remote Control
Samsung Electronics • Use to mark a segment to repeat between A and B.
SUBTITLE Button A-B REPEAT Button
• Use to access various camera angles on a DVD.
ANGLE Button
• This button functions as a toggle switch.
ENTER/DIRECTION Button (UP/DOWN or LEFT/RIGHT Button)
• Brings up the Disc menu.
MENU Button
• Displays the current disc mode.
DISPLAY Button
• Allows you to program a specific order.
MODE Button
• Use to remove menus or status displays from the screen.
CLEAR Button
• Use to skip the title, chapter, or track.
NOTE
This
icon indicates an invalid button press.
Turn the headphone volume down to the minimum setting before connecting. Adjust to your desired volume after connection.
• Check if there is any fluorescent lighting nearby.
• Check if remote sensor is blocked by obstacles.
• Check if the batteries are drained.
• Begin/Pause disc play.
SKIP Buttons
• Check the polarity + - of the batteries (Dry-Cell)
To Connect Headphones (not included) (DVD-909 only)
Replace the battery cover.
Insert two AA batteries. Make sure that the polarities (+ and -) are aligned correctly.
Open the battery cover on the back of the remote.
If remote doesn’t operate properly:
3.
1. 2.
Install Batteries in the Remote
VOLUME UP/DOWN Buttons
CHANNEL UP/DOWN Buttons
3D SOUND Button BOOKMARK Button PLAY/PAUSE Button
• To control the master volume of the player.
VOLUME CON. Button
• Use to set the remote to control a compatible TV.
TV POWER Button
• Allows you to repeat play a title, chapter, track, or disc.
REPEAT Button
• Use this button to access various audio functions on a disc.
AUDIO Button
• Accesses a music or video display directly.
TOP MENU Button
• Returns to a previous menu.
RETURN Button
• Advances playback one frame at a time.
STOP Button STEP Button
• Allows you to search forward/backward through a disc.
ZOOM Button SEARCH Buttons
• Brings up the DVD player’s Setup menu.
TV POWER Button
DVD POWER Button NUMBER Buttons OPEN/CLOSE Button SETUP Button
TV/VIDEO Selection Button
TV Function Buttons
DVD Function Buttons
A Tour of the Remote Control (Cont’d)
Operating Instructions
4-9
4-10
DVD-909
DVD PLAYER
TV
L2
R2
Basic Audio (In case of Method 1 or 2)
MIXED AUDIO OUT
L1
L
R1
R
Audio Input Jacks
Method 1
VIDEO OUT
V2
V1
Good picture
AV Cable (included)
OR
Video Input Jack
TV (Normal, Widescreen, Projection, etc..)
Connecting to a TV
• Refer to owner’s manual of the components you are connecting for more information on those particular components.
• Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
Before Connecting the DVD Player
Better picture
S-VIDEO OUT
OR
S-Video Cable (included)
S-Video Jack
Method 2
Best picture (If RGB is selected in SETUP MENU)
Scart Input Jack
Method 3
AV1
Scart Cable (not included)
• Method 3 DVD Player + TV with Scart Input Jack (Audio & Video)
• Method 2 DVD Player + TV with S-Video Input Jack
• Method 1 DVD Player + TV with Video Input Jack
Connecting to a TV (For Video)
The following diagrams show common connection examples that can be used for connecting your DVD player to a TV or other equipment.
Choosing a Connection
L2
L1
NOTE
S/W
COAXIAL
COAXIAL
DVD PLAYER
AUDIO SYSTEM
TV
AV2
AV1
AV2/OTHER EQUIPMENT
AV1/TV
OTHER EQUIPMENT
VIDEO
DVD
An Example of Connecting DVD with Other Equipment
Digital Audio Out
DIGITAL AUDIO OUT
OPTICAL
OR
OPTICAL
Digital Audio Input Jacks
Dolby Digital Decoder
Method 3
You can build up the optimum AV system by following the connection examples on this page and the previous page.
• Method 3 DVD Player + Amplifier with Dolby Digital Decoder/DTS Decoder
• Method 2 DVD Player + Amplifier with 5.1ch Analog Input Jacks
• Method 1 DVD Player + 2ch Stereo Amplifier or Dolby Pro Logic Decoder
L
CENTER
ANALOG AUDIO OUT
SURROUND
L
Subwoofer
Center
Analog Audio Out
R
FRONT
Rear (LH)
Rear (RH)
R
Front (LH)
Front (RH)
Connecting to an Audio System
Mixed Audio Out
MIXED AUDIO OUT
R2
R1
L
Audio Input Jacks
R
5.1ch Analog Amplifier
2ch Amplifier
Method 2
Audio Input Jacks
Method 1
Connecting to an Audio System
Choosing a Connection (Cont’d)
SCART JACK
Operating Instructions
Samsung Electronics
Samsung Electronics
DVD-709
DVD PLAYER
TV
Good picture
OR
Connecting to a TV (For Video)
Method 2
Better picture
S-VIDEO OUT
AV
Scart Cable (not included)
Best picture (If RGB is selected in SETUP MENU)
Scart Input Jack
Method 3
• Method 3 DVD Player + TV with Scart Input Jack (Audio & Video)
• Method 2 DVD Player + TV with S-Video Input Jack
• Method 1 DVD Player + TV with Video Input Jack
S-Video Jack
S-Video Cable (included)
Basic Audio (In case of Method 1 or 2)
AV Cable (included)
VIDEO OUT
L
L
Method 1
Video Input Jack
ANALOG AUDIO OUT
R
R
Audio Input Jacks
TV (Normal, Widescreen, Projection, etc..)
Connecting to a TV
• Refer to owner’s manual of the additional components you are connecting for more information for those particular components.
• Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
Before Connecting the DVD Player
The following diagrams show common connection examples that can be used for connecting your DVD player to a TV or other equipment.
Choosing a Connection
Connecting to an Audio System
L
ANALOG AUDIO OUT
VIDEO OUT
S-VIDEO OUT
TV SYSTEM SELECT
PAL
SECAM
NTSC
You can build up the optimum AV system by following the connection examples on this page and the previous page.
• Method 2 DVD Player + Amplifier with Dolby Digital Decoder/DTS Decoder
Rear Panel
DIGITAL AUDIO OUT
Digital Audio Out
ANALOG AUDIO OUT
L
Analog Audio Out
R
• Method 1 DVD Player + 2ch Stereo Amplifier or Dolby Pro Logic Decoder
NOTE
R
Digital Audio Input Jack
L
Audio Input Jacks R
Dolby Digital Decoder
Method 2
2ch Amplifier
Method 1
Connecting to an Audio System
Choosing a Connection (Cont’d)
SCART JACK
AV
DVD PLAYER
AUDIO SYSTEM
Operating Instructions
4-11
4-12
DVD-909
DVD PLAYER
TV
Better picture
Good picture
Basic Audio
V2
V1
OR OR
S-Video Cable (included)
S-Video Jack
S-VIDEO OUT
L2
L1
AV Cable (included)
Video Input Jack
Method 2
Y
Y
Best picture
COMPONENT VIDEO OUT
Pb
Pr
Pr
Pb
Component Video Jacks
Method 3
Video Cables (not included)
• Method 3 DVD Player + TV with Component Video Jacks
• Method 2 DVD Player + TV with S-Video Input Jack
VIDEO OUT
L
Method 1
Connecting to a TV (For Video)
• Method 1 DVD Player + TV with Video Input Jack
MIXED AUDIO OUT
R2
R1
R
Audio Input Jacks
TV (Normal, Widescreen, Projection, etc..)
Connecting to a TV
• Refer to owner’s manual of the components you are connecting for more information on those particular components.
• Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
Before Connecting the DVD Player
The following show examples of connections commonly used to connect the DVD player with a TV and other components.
Choosing a Connection
L2
L1
DIGITAL AUDIO OUT
OPTICAL COAXIAL
FRONT
L
SW
CENTER
ANALOG AUDIO OUT
R SURROUND L
R
Rear Panel
MIXED ADUIO OUT
R2
R1
Mixed Audio Out
MIXED AUDIO OUT
R2
R1
L
L1
L2
V1
VIDEO OUT S-VIDEO OUT
V2
Pr
Y
COMPONENT VIDO OUT
Pb
L
S/W
CENTER
ANALOG AUDIO OUT
SURROUND
L
TV SYSTEM SELECT
PAL
SECAM
NTSC
COAXIAL
COAXIAL
Connecting to an Audio System
Digital Audio Out
DIGITAL AUDIO OUT
OPTICAL
OR
OPTICAL
Digital Audio Input Jacks
Dolby Digital Decoder
Method 3
DVD PLAYER
AUDIO SYSTEM
• Method 3 DVD Player + Amplifier with Dolby Digital Decoder/MPEG-2 Decoder/DTS Decoder
• Method 2 DVD Player + Amplifier with 5.1ch Analog Input Jacks
• Method 1 DVD Player + 2ch Stereo Amplifier or Dolby Pro Logic Decoder
Subwoofer
Center
Analog Audio Out
R
FRONT
Rear (LH)
Rear (RH)
R
Front (LH)
Front (RH)
Audio Input Jacks
R
5.1ch Analog Amplifier
2ch Amplifier
Method 2
Audio Input Jacks
Method 1
Connecting to an Audio System
Choosing a Connection (Cont’d)
COMPONENT VIDEO RCA JACK
Operating Instructions
Samsung Electronics
Samsung Electronics
DVD-709
DVD PLAYER
TV
S-VIDEO OUT
Best picture
Basic Audio
OR
S-Video Cable (included)
VIDEO OUT
AV Cable (included)
Method 2 S-Video Jack
Better picture
L
L
Video Input Jack
Method 1
• Method 2 DVD Player + TV with S-Video Input Jack
• Method 1 DVD Player + TV with Video Input Jack
Connecting to a TV (For Video)
ANALOG AUDIO OUT
R
R
Audio Input Jacks
TV (Normal, Widescreen, Projection, etc..)
Connecting to a TV
• Refer to owner’s manual of the additional components you are connecting for more information for those particular components.
• Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
Before Connecting the DVD Player
The following show examples of connections commonly used to connect the DVD player with a TV and other components.
Choosing a Connection
DIGITAL AUDIO OUT
L
NTSC
VIDEO OUT
S-VIDEO OUT
TV SYSTEM SELECT
PAL
SECAM
DVD PLAYER
AUDIO SYSTEM
• Method 2 DVD Player + Amplifier with Dolby Digital Decoder/MPEG-2 Decoder/DTS Decoder
• Method 1 DVD Player + 2ch Stereo Amplifier or Dolby Pro Logic Decoder
Connecting to an Audio System
DIGITAL AUDIO OUT
Digital Audio Out
L
ANALOG AUDIO OUT
R
Analog Audio Out
ANALOG AUDIO OUT
R
Rear Panel
Digital Audio Input Jack
L
Audio Input Jacks R
Dolby Digital Decoder
Method 2
2ch Amplifier
Method 1
Connecting to an Audio System
Choosing a Connection (Cont’d)
COMPONENT VIDEO RCA JACK
Operating Instructions
4-13
4-14
TV SYSTEM SELECT
NTSC
TV SYSTEM SELECT
PAL
PAL-encoded (DVD/VIDEO-CD)
TV SYSTEM SELECT
TV SYSTEM SELECT
TV SYSTEM SELECT
TV SYSTEM SELECT
• VIDEO-CD only.
PAL
SECAM
PAL
SECAM
NTSC
PAL
PAL
NTSC
SECAM
NTSC
NTSC
SECAM
PAL
PAL
SECAM
TV
SECAM
NTSC-encoded (DVD/VIDEO-CD)
DISC
NTSC
You should set TV SYSTEM to 'NTSC'.
If you use NTSC-TV
TV SYSTEM SELECT
PAL
SECAM
NTSC
PAL-N/M-encoded (DVD/VIDEO-CD)
TV SYSTEM SELECT
PAL-N
PAL-M
NTSC
TV SYSTEM SELECT
PAL-M
NTSC
PAL-N
TV SYSTEM SELECT
TV
TV SYSTEM SELECT
PAL-N
PAL-M
NTSC
•
VIDEO-CD only.
TV SYSTEM SELECT
PAL-N
PAL-M
NTSC
TV SYSTEM SELECT
PAL-N
PAL-M
NTSC
NTSC
You should set TV SYSTEM to 'NTSC'.
If you use NTSC-TV
TV SYSTEM SELECT
PAL-N
PAL-M
NTSC
TV SYSTEM SELECT
PAL-N
PAL-M
NTSC
PAL-M
TV SYSTEM SELECT
PAL-N
PAL-M
NTSC
You should set TV SYSTEM to 'PAL-M'.
If you use PAL-M-TV
• When you playback NTSC-encoded disc with PAL-N/M-TV, some discs may produce black bands at the top and bottom of the screen.
• Select the TV-SYSTEM when in stop mode.
• When the selected TV-SYSTEM doesn't coincide with the system of your TV, normal color picture may not be displayed.
PAL-N
NTSC-encoded (DVD/VIDEO-CD)
DISC
TV SYSTEM SELECT
PAL-N
PAL-M
NTSC
You should set TV SYSTEM to 'PAL-N'.
If you use PAL-N
* This switch is located in the rear of DVD player.
TV SYSTEM SELECT
PAL-N
PAL-M
NTSC
PAL
SECAM
NTSC
SECAM
TV SYSTEM SELECT
PAL
SECAM
NTSC
You should set TV SYSTEM to 'SECAM'.
If you use SECAM-TV
• When you playback NTSC-encoded disc with PAL-TV, some discs may produce black bands at the top and bottom of the screen.
• Select the TV-SYSTEM when in stop mode.
NTSC
You should set TV SYSTEM to 'PAL'.
If you use PAL-TV
* This switch is located in the rear of DVD player.
TV SYSTEM SELECT
PAL
SECAM
• When the selected TV-SYSTEM doesn't coincide with the system of your TV, normal color picture may not be displayed.
• Only when you playback PAL-N/M-encoded DVD with NTSC-TV, the player can not playback the disc.
• Only when you playback PAL-encoded DVD with NTSC-TV. The player can not playback the disc.
NTSC
You can enjoy NTSC or PAL-N/M encoded discs by using your TV SYSTEM SELECT switch to choose the appropriate system.
TV system select (PAL-N/M)
You can enjoy NTSC or PAL encoded discs by using your TV SYSTEM SELECT switch to choose the appropriate system.
TV system select (PAL/SECAM)
Operating Instructions
Samsung Electronics
5. Disassembly and Reassembly 5-1 Cabinet and PCB 5-1-1 Door-Tray Removal 1) Supply power and open Tray Œ. 2) Disassemble the Door-Tray ´ in direction of arrow ÒAÓ. 3) Close Tray Œ and power off. Note : If Tray Œ doesnÕt open, insert a Screw driver ¨ into the Emergency hole ˇ(as shown in detailed drawing) and then turn it in the direction of arrow ÒBÓ. Open Tray manually.
Œ TRAY ´ DOOR-TRAY "A"
ˇ EMERGENCY HOLE "B"
¨ SCREW DRIVER
Fig. 5-1 Door-Tray Removal
Samsung Electronics
5-1
Disassembly/Reaasembly
5-1-2 Top Cabinet Removal 1) Remove 3 Screws Œ on the back Top Cabinet. 2) Remove 2 Screws ´, ˇ on the left and right side. 3) Lift up the Top Cabinet in direction of arrow.
Œ 3 SCREWS ´ 1 SCREW
ˇ 1 SCREW
Fig. 5-2 Top Cabinet Removal
5-2
Samsung Electronics
Disassembly/Reaasembly
5-1-3 Ass’y Front-Panel, Phone/Power PCB, Play PCB Removal (DVD-909) 1) Remove 2 Screws Œ and AssÕy Front Panel ´. 2) Remove Knob-Volume ˇ and 2 Screws ¨. 3) Remove Bracket-Phone ˆ and Phone/Power PCB Ø. 4) Remove Knob-Jog ∏ and Knob-Shuttle ”. 5) Remove 4 Screws ’ and Play PCB ˝.
¨ 2 SCREWS Œ 2 SCREWS
ˆ BRACKET-PHONE Ø PHONE/POWER PCB
’ 4 SCREWS
˝ PLAY PCB
ˇ KNOB-VOLUME
´ ASS'Y FRONT-PANEL ” KNOB-SUHTTLE ∏ KNOB -JOG Fig. 5-3 Ass’y Front-Panel, Phone/Power PCB, Play PCB Removal (DVD-909)
Samsung Electronics
5-3
Disassembly/Reaasembly
5-1-4 Ass’y Front-Panel, Power PCB, Play PCB Removal (DVD-709) 1) Remove 2 Screws Œ and AssÕy Front Panel ´. 2) Remove 2 Screws ˇ and Power PCB ¨. 3) Remove 3 Screws ˆ and Play PCB Ø.
Œ 2 SCREWS ˇ 2 SCREWS ¨ POWER PCB
ˆ 3 SCREWS
Ø PLAY PCB ´ ASS'Y FRONT-PANEL
Fig. 5-4 Ass’y Front-Panel, Power PCB, Play PCB Removal (DVD-709)
5-4
Samsung Electronics
Disassembly/Reaasembly
5-1-5 Main PCB, Jack PCB Removal (DVD-909 ; Component Video RCA Jack Model) 1) Remove 4 Screws Œ and 5 Screws ´. 2) Lift up the Jack PCB ˇ. 3) Remove 3 Screws ¨ and lift up the Main PCB ˆ.
Π4 SCREWS
ˇ JACK PCB ¨ 3 SCREWS
ˆ MAIN PCB ´ 5 SCREWS
Fig. 5-5 Main PCB, Jack PCB Removal (DVD-909 ; Component Video RCA Jack Model)
Samsung Electronics
5-5
Disassembly/Reaasembly
5-1-6 Main PCB, Jack PCB Removal (DVD-709 ; Component Video RCA Jack Model) 1) Remove 4 Screws Œ and 1 Screw ´. 2) Lift up the Jack PCB ˇ. 3) Remove 3 Screws ¨ and lift up the Main PCB ˆ.
Π4 SCREWS
ˇ JACK PCB ¨ 3 SCREWS
ˆ MAIN PCB ´ 1 SCREW
Fig. 5-6 Main PCB, Jack PCB Removal (DVD-709 ; Component Video RCA Jack Model)
5-6
Samsung Electronics
Disassembly/Reaasembly
5-1-7 Main PCB, Jack PCB Removal (DVD-909 ; Scart Jack Model) 1) Remove 4 Screws Œ and 6 Screws ´. 2) Lift up the Jack PCB ˇ. 3) Remove 3 Screws ¨ and lift up the Main PCB ˆ.
Π4 SCREWS
ˇ JACK PCB ¨ 3 SCREWS
ˆ MAIN PCB ´ 6 SCREWS
Fig. 5-7 Main PCB, Jack PCB Removal (DVD-909 ; Scart Jack Model)
Samsung Electronics
5-7
Disassembly/Reaasembly
5-1-8 Main PCB, Jack PCB Removal (DVD-709 ; Scart Jack Model) 1) Remove 4 Screws Œ and 3 Screws ´. 2) Lift up the Jack PCB ˇ. 3) Remove 3 Screws ¨ and lift up the Main PCB ˆ.
Π4 SCREWS
ˇ JACK PCB ¨ 3 SCREWS
ˆ MAIN PCB ´ 3 SCREWS
Fig. 5-8 Main PCB, Jack PCB Removal (DVD-709 ; Scart Jack Model)
5-8
Samsung Electronics
Disassembly/Reaasembly
5-1-9 Ass’y Deck Removal 1) Remove 4 Screws Œ from the AssÕy Deck and lift it up.
Π4 SCREWS
Fig. 5-9 Ass’y Deck Removal
Samsung Electronics
5-9
Disassembly/Reaasembly
5-2 PCB Location DVD-909
JACK PCB
MAIN PCB
PHONE/POWER PCB
PLAY PCB
DVD-709
JACK PCB
POWER PCB
MAIN PCB
PLAY PCB Fig. 5-10 PCB Location 5-10
Samsung Electronics
Disassembly/Reaasembly
5-3 Connector Diagram DVD-909 CT1
´
JACK PCB
Œ Ô
ˆ
PHONE/POWER PCB
¨
CT6
CT2
∏ CT3
ˇ
CT4 CT5
PLAY PCB
’
” ˝
Ø
MAIN PCB
NO.
CONNECTOR NO.
Œ
CON23-A
´
CN18
ˇ
CON21
¨
DIRECTION
CONNECTOR NO.
PHONE/POWER PCB
CT1
JACK PCB
JACK PCB
CT1
PHONE/POWER PCB
PLAY PCB
CT2
JACK PCB
CN15
CN15
JACK PCB
CT2
PLAY PCB
CON21
ˆ
CN12
JACK PCB
CT3
MAIN PCB
CN7
Ø
CN7
MAIN PCB
CT3
JACK PCB
CN12
∏
CN11
JACK PCB
CT4
MAIN PCB
CN8
”
CN8
MAIN PCB
CT4
JACK PCB
CN11
’
CN5
DECK PCB
CT5
MAIN PCB
CN6
˝
CN6
MAIN PCB
CT5
DECK PCB
CN5
Ô
CON23
PHONE/POWER PCB
CT6
JACK PCB
CN17
CN17
JACK PCB
CT6
PHONE/POWER PCB
CON23
CN18 CON23-A
Fig. 5-11 Connector Diagram (DVD-909) Samsung Electronics
5-11
Disassembly/Reaasembly
DVD-709 POWER PCB Œ ´
JACK PCB
CT1
ˆ
¨
CT2
∏ CT3 ˇ
CT4 PLAY PCB
CT5 ’
” ˝
Ø
MAIN PCB
NO.
CONNECTOR NO.
Œ
KCN2
´
CN18
ˇ
CON22
¨
DIRECTION
CONNECTOR NO.
POWER PCB
CT1
JACK PCB
CN18
JACK PCB
CT1
POWER PCB
KCN2
PLAY PCB
CT2
JACK PCB
CN16
CN16
JACK PCB
CT2
PLAY PCB
CON22
ˆ
CN12
JACK PCB
CT3
MAIN PCB
CN7
Ø
CN7
MAIN PCB
CT3
JACK PCB
CN12
∏
CN11
JACK PCB
CT4
MAIN PCB
CN8
”
CN8
MAIN PCB
CT4
JACK PCB
CN11
’
CN5
DECK PCB
CT5
MAIN PCB
CN6
˝
CN6
MAIN PCB
CT5
DECK PCB
CN5
Fig. 5-12 Connector Diagram (DVD-709)
5-12
Samsung Electronics
Disassembly/Reaasembly
5-4 Deck 5-4-1 Tray Removal 1) Remove 2 Screws Œ and lift up the Cover Sheet ´, AssÕy-Deck Clamper ˇ. 2) Insert a Screw driver ˆ into Emergency hole ¨ and push it in the direction of arrow ÒAÓ. When the Tray Ø comes out a little, pull it in the direction of arrow ÒBÓ by hand. 3) Pull the Tray Ø to disassemble, while simultaneously pushing the Hook ∏, ” in direction of arrow ÒAÓ, ÒBÓ. Œ 2 SCREWS
´ COVER SHEET
ˇ ASS'Y - DECK CLAMPER
∏ HOOK "C"
"B"
"D" ” HOOK
Ø TRAY
ˆ SCREW DRIVER "A" ¨ EMERGENCY HOLE
Fig. 5-13 Tray Removal
Samsung Electronics
5-13
Disassembly/Reaasembly
5-4-2 Ass’y-Deck Sub Removal 1) Remove 2 Screws Œ and disassemble the AssÕy-PCB deck ´. 2) Disassemble the AssÕy-Deck Sub ¨ in direction of arrow ÒBÓ, while simultaneously pushing the Hook ˇ in direction of arrow ÒAÓ.
¨ ASS'Y - DECK SUB
"B"
"A"
ˇ HOOK
´ ASS'Y - PCB DECK
Œ 2 SCREWS Fig. 5-14 Ass’y-Deck Sub Removal
5-14
Samsung Electronics
Disassembly/Reaasembly
5-4-3 Chassis-Main Parts Removal 1) Lift up the Gear-Tray Œ, remove 1 Screw ´ and lift up the Gear-Cam Center ˇ. 2) Lift up the Belt-Pulley ¨, remove 1 Screw ˆ and lift up the Pulley-Gear Ø. 3) Remove 1 Screw ∏ and lift up the Gear-Tray A ” and Gear-Cam Sub ’. 4) Remove 2 Screws ˝ and disassemble the AssÕy-Motor Load Ô. 5) Remove 1 Screw and disassemble the Lever-Open S/W Ò. 6) Lift up the Shaft-Syncro Ú and remove the 2 Gear-Syncro Æ in both directions.
ˇ GEAR - CAM CENTER ´ 1 SCREW ’ GEAR - CAM SUB Œ GEAR - TRAY ” GEAR - TRAY A ∏ 1 SCREW
¨ BELT - PULLEY ˆ 1 SCREW Ø PULLEY - GEAR ˝ 2 SCREWS
ˇ GEAR - CAM CENTER TIMING ALIGN TWO ARROWS
’ GEAR - CAM SUB Æ GEAR - SYNCRO Ú SHAFT - SYNCRO Æ GEAR - SYNCRO Ô ASS'Y - MOTOR LOAD
Ò LEVER - OPEN S/W 1 SCREW
Fig. 5-15 Chassis-Main Parts Removal
Samsung Electronics
5-15
Disassembly/Reaasembly
5-4-4 Ass’y-Brkt Deck Removal 1) Remove 4 Screws Œ. 2) Lift up the AssÕy-Brkt Deck ´.
Π4 SCREWS
´ ASS'Y - BRKT DECK
Fig. 5-16 Ass’y-Brkt Deck Removal
5-16
Samsung Electronics
Disassembly/Reaasembly
5-4-5 Ass’y- Deck Parts Removal 1) Remove 3 Screws Œ and disassemble 3 Holder-Cams ´. 2) Disassemble the Rack-Slide ˆ and AssÕy-Pickup Ø, 2 Screws ¨ while simultaneously removing the Shaft-P/U ˇ. 3) Remove 3 Screws ∏ and disassemble the AssÕy-Motor Spindle ”. 4) Remove the Washer-Plain ’ and disassemble the AssÕy-Gear Feed AU/AL ˝. 5) Remove the Washer-Plain Ô and disassemble the Gear-Feed B . 6) Remove the Washer-Plain Ò and disassemble the AssÕy-Gear Feed CU/CL Ú.
´ HOLDER - CAM Œ 2 SCREWS
” ASS'Y - MOTOR SPINDLE
˝ ASS'Y - GEAR FEED AU/AL
∏ 3 SCREWS
’ WASHER - PLAIN
ˇ SHAFT - P/U
GEAR - FEED B
Ø ASS'Y - PICK UP
Ô WASHER - PLAIN ˇ SHAFT - P/U
Ú ASS'Y GEAR - FEED CU/CL Ò WASHER - PLAIN
ˆ RACK - SLIDE ¨ 2 SCREWS Fig. 5-17 Ass’y- Deck Parts Removal
Samsung Electronics
5-17
Disassembly/Reaasembly
MEMO
5-18
Samsung Electronics
6. Circuit Descriptions 6-1 S.M.P.S. 6-1-1 Comparsion between Linear Power Supply and S.M.P.S. 6-1-1 (a) Linear Vout
Vreg REGULATOR
+ Vp (Np) –
Common power (Ex.120/220V 50/60Hz)
+ Vs – (Ns)
+
Fig. 6-1 Linear Power Supply 3 Waveform/Description Vs
0
Input : Common power to transformer (Vp).
t
Fig. 6-2 Vs
0
The output Vs of transformer is determined by the ratio of 1st Np and 2nd Ns. Vs = (Ns/Np) x Vp
t
Fig. 6-3 Vout
0
t
Vout is output (DC) by diode and condensor.
Fig. 6-4 Samsung Electronics
6-1
Circuit Descriptions
3 Advantages and disadvantages of linear power supply
Change by common power
1) Advantages : Little noise because the output waveform of transformer is sine wave. 2) Disadvantages : Œ Additional margin is required because Vs is changed (depending on power source). (The regulator loss is caused by margin design). ´ Greater core size and condensor capacity are needed, because the transformer works on a single power frequency.
v Vout
Vreg
0
t Regulator loss Fig. 6-5
6-1-1 (b) S.M.P.S. (Pulse width modulation method) Vout
Transformer (Np) (Ns) + + (Vp) (Vs) – –
REGULATOR
+ + Vin
Switch
ON/OFF Control
+ Vs switch – I switch
Fig. 6-6 3 Terms 1) 1st : Common power input to 1st winding. 2) 2nd : Circuit followings output winding of transformer. 3) f (Frequency) : Switching frequency (T : Switching cycle) 4) Duty : (Ton/T) x 100
6-2
Samsung Electronics
Circuit Descriptions
6-1-2 Circuit description (FLY-Back PWM (Plise Width Modulation) Control) 6-1-2 (a) AC Power Rectification/Smoothing Terminal 1) PD01,PD02,PD03,PD04 : Convert AC power to DC(Wave rectification) 2) PE3 : Smooth the voltage converted to DC(Refer to VIN of Fig. 6-7) 3) PC01, PC02, PC10, PC11, PC12, PC13, PL01, PL02, PL03 : Noise removal at power input/output 4) PVA1 : SMPS protection at power surge input (PVA1 pattern open is to remove noise) 5) PR10 : Rush current limit resistance at the moment of power cord insertion. Œ Rush current = (AC input voltage x 1.414 - Diode drop voltage) / Pattern resistance + PL02,01 resistance + PC10 resistance + PR10) (AC230V based : approx. 26A) ´ Without PR10, the bridge diode might be damaged as the rush current increases.
6-1-2 (b) SNUBBER Circuit : PR15, PR16, PC04, PC05, PD11, PR17 1) Prevent residual high voltage at the terminals of switch during switch off/Suppress noise. High inverted power occurs at switch (PIC1) off, because of the 1st winding of transformer : (V= LI xdi/dt. LI : Leakage Induction) A very high residual voltage exists on both terminals of PIC1 because dt is a very short.
Vswitch Inverted power by leakage inductance
dt
2) SNUBBER circuit protects PIC1 from damage through leakage voltage suppression by RC, (Charges the leakage voltage to PD11 and PC04, and discharges to PR15 and PR16).
0
t
3) PC05, PR17 : For noise removal
Toff Fig. 6-7
6-1-2 (c) PIC1 Vcc circuit 1) PR11, PR12, PR13, PR14 : PIC1 driving resistance (PIC1 works through driving resistance at power cord in) 2) PIC1 Vcc : PR18, PD12, PE6 Œ Use the output of transformer as Vcc, because the current starts to flow into transformer while PIC1 is active. ´ Rectify to PD12 and smooth to PE6. ˇ Use the output of transformer as PIC1 Vcc : The loads are different before and after PIC1 driving. (Vcc of PIC1 decreases below OFF voltage, using only the resistance due to load increase after PIC1 driving.)
Samsung Electronics
6-3
Circuit Descriptions
6-1-2 (d) Feedback Control Circuit Trans PD33 PIC1 STR-G6153T
PL34
PE33
5.8V
PC34
OCP
GND # DRAIN !
@ %
PR35
$ F/B
VCC C
A
E
K
PIC2 PC09
PR36
PC44
PR37
PR38
K
1st GND
P PIC3
2.5V A
PR39
2nd GND Fig. 6-8 1) F/B terminal of PIC1 determines output duty cycle. 2) C-E(Collector-Emitter) of PIC2 and F/B potential of PIC1 are same. 3 Operation descriptions 1) Internal OP-Amp Ô+Õ base potential of PIC3 is 2.5V and external Ò-Ó input potential is connected with PR38 and PR39 to maintain Vout of 5.8V. (Vout = ((PR36 x PR39) / PR39) x 2.5V) 2) If load of 5.8 V terminal increases(or AC input voltage decreases) and Vout decreases below 5.8V, then : PIC3 ÔPÕ potential down below 2.5V --> PIC3 A-K of base current down --> PIC3 of A-K current down --> PIC2 Diode current down --> PIC2 C-E current down --> PIC2 C-E voltage up --> PIC1 F/B voltage up --> Out Duty up --> Transformer 1st current up --> Transformer 1st power up --> Vout up --> Maintain Vout 5.8V 3) If load of 5.8 V terminal decreases(or AC input voltage rises) and Vout rises above 5.8V, then : Reverse sequence of the above description --> Duty down --> Vout down --> Maintain 5.8V (i.e., the feedback to maintains 5.8V). Œ PR35, PR36 : Reduce 5.8V overshoot ´ PR37, PC44 : Prevent PIC3 oscillation(for phase correction) ˇ PC09 : Adjust feedback response rate
6-4
Samsung Electronics
Circuit Descriptions
6-1-3 Internal Block Diagram 6-1-3 (a) Internal Block Diagram of S.M.P.S. Circuit FLT Driving Circuit
Smoothing Circuit Noise Removal (SNUBBER)
Converter
Rectified Circuit
3.3V Rectified VoltageCircuit
5V Rectified Smoothing Circuit
5V Rectified VoltageCircuit (x2)
O U T P U T
Motor 8V 1 Port
PWM Control Circuit (1L0380)
Line Filter
3.3V Rectified Smoothing Circuit
Voltage Detection Circuit Power IN (85~265V)
8V Rectified Smoothing Circuit
8V Rectified VoltageCircuit
-8V Rectified Smoothing Circuit
-8V Rectified VoltageCircuit
Fig. 6-9
6-1-3 (b) PIC1 (STR-G6153T) Internal Block Diagram Vcc
5
6.3V 2uA
+ _
32V
Sync.
Voltage Ref.
UVLO
Vck
1mA OSC.
Feedback
1
Drain
3
Source GND
4 2.5R
S Q R
R
LEB
Voffset
Sense
Rsense
5v
Reset 7.5V Reset
+ _
Sense FET
S Q
Thermal Protection
R
OVP
Control IC
2 OCP
Fig. 6-10 Samsung Electronics
6-5
Circuit Descriptions
6-2 RF 6-2-1 RIC1 (KS1461) KS1461 is combined with KS1452 and KS1453 as bipolar IC developed for DVD SERVO system. Main features include DVD waveform equalizing, CD waveform equalizing, focus error signal generation, 3-beam tracking error signal generation, DPD 1-beam tracking error, defect, envelope, MIRR output, etc. after receiving the pick-up output converted into I/V.
6-2-1 (a) Basic Potentiometer KS1461 uses a single power method and each circuit is based on V of 2.5V. V (Pin 12, 20, 24, 67) terminal is needed for IC, which uses the peripheral V.
6-2-1(b) RF signal Fig. 6-11 shows the flow of signal generated by the pick-up. A, B, C, D signals detected from pick-up are converted in to RF signal(A+B+C+D) via RF summing AMP. 104
MIRRI RFAGCO 474 EQIN ? . m A B C
PICK-UP
D PD LD F
104
%
104
^
104
&
104
*
MIRR RE SUM & AGC
RF EG
G MIRR ,
TESEL
E
DPD TE
Mhx
y TE
3 4 TE 5 6 7
i ABCD SUM
8
ABCDI 103
ENV FOK DEFECT
FE w E
RFEQO
I P [ F d T
ABCD ENV FOKB DFCT2 DFCT1 FE
ALPC Fig. 6-11
Fig. 6-12 shows the waveform-equalizing block diagram for the RF signal. It outputs to EQout (Pin 86) terminal by initially changing switching AMP gain of DVD and CD, and then adjusting the level in RF SUM & AGC. It controls RF SUM & AGC gain by means of Pin 89-95 and interfaces with PWM signal, (output from PWM terminal of KS1453, via low-pass filter to adjust boost gain and peak frequency. EQout terminal is connected with EQin (Pin 86). 6-6
Samsung Electronics
Circuit Descriptions
EQIN
,
VZOCTL
‚
RFEQO
RFDVCC
· VREFEQ
PLLGF
EQG PWM1
°
RF EQ
EQF
.
‡
REAGCO ?
PWM2
474
Fig. 6-12 The control parameters of DVD EQ and CD EQ are as follows. 1) DVD CD EQ control parameter Œ EQG (Pin 97) : Changes the gain of peak frequency with EQ frequency characteristic. Convert PWM signal, output from KS1453, into DC via low-pass filter. ´ EQF (Pin 98) : Changes the peak frequency with EQ frequency characteristic. Convert PWM signal, output from KS1453, into DVD via low-pass filter.
Samsung Electronics
6-7
Circuit Descriptions
6-3 System Control 6-3-1 Outline The main micom peripheral circuit is composed of 16bit Micom (MIC1 ; TMP93CM41F), 8M EPROM (MIC8 ; AM27C080) for Microcode and data save, 512 byte EE-PROM (MIC5 ; KS24C020) for permanent storage of data needed at power off, MIC4 (74AC573) to latch only address in the bus where address and data are mixed, address decoder (MIC7 ; 74HC00) for selection of ex-ternal device chip and 20MHz clock oscillator for micom operation. The Micom (MIC1 ; TMP93CM41F) mounted in main board analizes the key commands of front panel or instructions of remote control through communication with Micom (FIC1 ; LC86P6232) of front and controls the devices on board to execute the corresponding commands after initializing the devices connected with micom on board at power on.
6-3-2 Block Diagram RIC1 RF AMP KS1461
SIC1 DIGITAL SERVO KS1452
DIC1 DATA PROCESSOR KS1453
FIC1 FRONT MICOM LC86P6232
MIC1 MAIN MICOM TMP93CM41F MIC7 ADDR DECODER 74HC00
MICOM BLOCK
VIC1 A/V DECODER ZIVA-3
VIC50 VIDEO ENCODER SAA7128/7120
AIC1,2,3,4 D/A CONVERTER AK4324
MIC2 ADDR LATCH 74AC573
DATA BUS
MIC5 EEPROM KS24C020
MIC8 EPROM AT27C080 LOW ADDRESS
HIGH ADDRESS Fig. 6-13
6-8
Samsung Electronics
Circuit Descriptions
6-3-3 Waveform Description When micom accesses each device sharing bus, it falls the chip select signal of corresponding chip to (CS2:MIC8-22, /DSPCS:DIC1-2, /DVDCS:VIC1-206/SRVCS:SIC1-10) 0 (Low) before trial. So to speak, the bus is used by time-division as shown in Fig 6-14, 6-15, 6-16. Two and more devices can't be accessed simultaneously. /CS2 /DSPCS /DVDCS /SRVCS /WR /RD
Fig. 6-14 • CH1 : CS2 (MIC8-22, EPROM CHIP SELECT) • CH2 : DSPCS (DIC1-2, DATA PROCESSOR CHIP SELECT) • CH3 : DVDCS (VIC1-206, A/V DECODER CHIP SELECT) • CH4 : SRVCS (SIC1-10, DIGITAL SERVO CHIP SELECT) • CH5 : WR (MIC1-73, MICOM OUTPUT WRITE SIGNAL) • CH6 : RD (MIC1-72, MICOM OUTPUT READ SIGNAL) /CS2 /DSPCS /DVDCS /SRVCS /WR /RD
Fig. 6-15 • CH1 : CS2 (MIC8-22, EPROM CHIP SELECT) • CH2 : DSPCS (DIC1-2, DATA PROCESSOR CHIP SELECT) • CH3 : DVDCS (VIC1-206, A/V DECODER CHIP SELECT) • CH4 : SRVCS (SIC1-10, DIGITAL SERVO CHIP SELECT) • CH5 : WR (MIC1-73, MICOM OUTPUT WRITE SIGNAL) • CH6 : RD (MIC1-72, MICOM OUTPUT READ SIGNAL) Samsung Electronics
6-9
Circuit Descriptions
/CS2 /DSPCS /DVDCS /SRVCS /WR /RD
Fig. 6-16 • CH1 : CS2 (MIC8-22, EPROM CHIP SELECT) • CH2 : DSPCS (DIC1-2, DATA PROCESSOR CHIP SELECT) • CH3 : DVDCS (VIC1-206, A/V DECODER CHIP SELECT) • CH4 : SRVCS (SIC1-10, DIGITAL SERVO CHIP SELECT) • CH5 : WR (MIC1-73, MICOM OUTPUT WRITE SIGNAL) • CH6 : RD (MIC1-72, MICOM OUTPUT READ SIGNAL)
6-10
Samsung Electronics
Circuit Descriptions
6-4 Servo 6-4-1 Outline SERVO system of DVD is divided into Focusing SERVO, Tracking SERVO, SLED Linked SERVO and CLV SERVO (DISC Motor Control SERVO). 1) Focusing SERVO Focuses the optical spot output from object lens onto the disc surface. Maintains a uniform distance between object lens of Pick-up and disc (for surface vibration of disc). 2) Tracking SERVO Make the object lens follow the disc track in use of tracking error signal (created from Pick-up). 3) SLED Linked SERVO When the tracking actuator inclines outwardly as the object lens follows the track during play, the SLED motor moves slightly (and counteracts the incline). 4) CLV SERVO (DISC Motor Control SERVO) Controls the disc motor to maintain a constant linear velocity (necessary for RF signal).
6-4-2 Block Diagram DISC
SLED M/T HALL PCB
LD
PD
SPINDLE M/T ›
FOCUSING TRACKING
CN1 HA1+ HA1– HA2– HA2+ SLED+ SLED– AO DO CO BO FO EO PD LD F– T+ T– F+ SPINDLE
# @ SIC8 % NJM2903 ^
MIC1 TMP 93CS41F
RIC1 KS1461 +
t SIC1 KS1452
1 & 2 8 7 DRIC2 KA3010D ! @
! x
DRIC1 0 KA3011D“ Fig. 6-17
Samsung Electronics
6-11
Circuit Descriptions
6-4-3 Operation 1) FOCUSING SERVO (1) FOCUS INPUT The focus loop is changed from open loop to closed loop, and the triangular waveform moves the object lens up and down (at pin 75 of SIC1 during Focus SERVO ON.) At that time, S curve is input to pin 65 of SIC1. ABAD (pin 39 of RIC1) signal, summing signal of PD A, B, C, D, is generated, and zero cross(2.5V) point occurs when S curve is focused and ABAD signal exceeds a preset,constant value. The focus loop is changed to closed loop, and the object lens follows the disc movement, maintaining a constant distance from the disc. (these operations are same in CD and DVD).
Vref
Pin75 of SIC1 (FOD)
Pin65 of SIC1 (FEI)
Vref
Pin39 of RIC1 (ABCD)
1.5V
Fig. 6-18 (2) PLAY When focus loop closes the loop during focus servo on, both pin 65 and pin 75 of SIC1 are controlled by VREF voltage (approx. 2.5V), and pin 1, 2 of DRIC2 are approximately 4.5V.
2) TRACKING SERVO (1) NORMAL PLAY MODE Œ For DVD Composite : The signal output from PD A, B, C, D of Pick-up, the tracking error signal (pin36 of RIC1) uses the phase difference of A+C and B+D in RIC1, and inputs to terminal 64 of SIC1. Then, it is output to SIC1 pin 76 via digital equalizer, and applied to the tracking actuator through DRIC2. Pins 17, 18 of SIC1 are controlled by VREF(approx. 2.5V) during normal play. Meanwhile, DVD repeats the track jump from 1 to 4 in inner direction at normal play (because data- read speed from disc is faster than data output speed on screen). ´ For CD, VCD Receive the signal output through E, F of Pick-up, from RIC1. The tracking error signal is similar to DVD.
6-12
Samsung Electronics
Circuit Descriptions
(2) SEARCH Mode : Search mode : Fine seek,(Moving the tracking actuator slightly little below 255 track) and coarse search, moving much in use of sled motor. The coarse search will be described in sled linked servo and now, the fine seek is explained shortly. If the object lens is located near target, cut off the tracking loop and give the control signal as many as desired count to move the tracking actuator via SIC1 pin 76 terminal(TRD).
3) SLED LINKED SERVO ¥ Normal play mode Move SLED motor slightly by means of PWM signal in SIC1 pin 73, as the tracking actuator moves along with track during play. Control to move the entire Pick-up as the tracking actuator moves. ¥ Coarse serach mode In case of long-distance search (such as chapter serach), SIC1 uses sled FG (SIC8 pin 1, 7, which is generated) by rotation of sled motor via hall PCB. Then, read ID and compute the existing track count after input of next track. If the existing track count is within fine seek range, tracking begins using fine seek.
4) CLV SERVO(DISC MOTOR CONTROL SERVO) Input RF signal (from Pick-up) to SIC1 pin59. Detect SYNC signal from RF in SIC1, and output PWM signal to SIC1 pin 55 for constant linear velocity.
Samsung Electronics
6-13
Circuit Descriptions
6-5 DVD Data Processor 6-5-1 Outline DIC1(KS1453) performs Sync detection, EFM/EFM demodulation and error correction and Spindle motor control (CLV control) after inputting sliced EFM signal of RF signal at disc playback and EFM read clock (PLCK) signal generated from PLL. Outputs data which converted to the last audio and video from A/V decoder(VIC1). KS1453 uses external memory(4M DRAM) as buffer as well as for error correction and carries out Variable Bit Rate transfer function. VBR function uses the external buffer as buffer to absorb the difference of transfer rate occurring because the transfer rate of disc playback is faster than data transfer rate demanded by A/V decoder(Video/Audio Signal Process Chip). In case of general disc refresh, the memory is almost filled up periodically. It is because Write rate to memory after disc playback and signal process is faster than Read of A/V decoder. When the memory is filled, this status is reported by interrupt to main micom, which controls the servo to kick back the pick-up to the previous track after memorizing the last data read from disc until now. It takes some times to jump to the previous track and return to the original(jump location) again. The memory will have an empty space because A/V decoder reads out data of memory. When the memory has an empty space, where data can be processed and written and the pick-up correctly gets to the original location(before kick back location) again, it reads data again avoids the interrupt of data read previously. The basic operation repeats to perform as described above.
6-5-2 Block Diagram DIC2 (KM416C254)
[ D A D R 8. . 0
[
[
D D 1 5. . 0
[
MDP 109 MDS 110
[
R C A A S S
W E
Z R A S
Z Z W O E E O O
Z C A S
CLOCK 27MHz CLOCK 33.8688MHz CLOCK 27MHz
O E
SDATA[7..0] CSTROBE DATREQ DIC1 DATACK (KS1453) DTER TOS MDAT[7:0] MRZA(3) ZCS(2) MWR(128) MRD(127) ZIRQZD(126)
14 95
177, 178
[
EFM 116 EFMI PLCK 104 PLCK
A 8. . 0
[
[
D 1 5. . 0
192 191 196 200
69 70 58 71 57
AD[7..0] HA[23..8] *WR(73)
VIC1 DVD-D[7..0] VSTROBE (ZiVA-3) REQUEST DACK HDATA[7..0] *ERR HADDR[3..0] /CS /RD /WR /INT
INTO(ZIRQZD) INT4(/INT) *RD(72)
MIC1 TMP93CM41F Fig. 6-19 6-14
Samsung Electronics
Circuit Descriptions
6-5-3 Waveform Description It measures the timing that data processed in DIC1 at DVD playback. STROBE REQ DACK SDATA all
2
2
0
1
0
Fig. 6-20 • CH1 : STROBE (DIC1-69, CLOCK) • CH2 : REQ (DIC1-70, DATA REQUEST) • CH3 : DACK (DIC1-58, DATA ACKNOWLEDGE) • CH4 : SDATA (DIC1-60~67, DATA)
Samsung Electronics
6-15
Circuit Descriptions
6-6 Video 6-6-1 Outline VIC50 sends VSYNC and HSYNC from VIC1(A/V decoder) and receives 8bit video data. VIC50 does RGB encoding, copy guard processing and D/A conversion of 8bit video data inputted from VIC1(A/V decoder) by control of MIC1(Micom). Video signal converted into analog signal is outputted via amplifier of analog part. (Main Board)
(Output Board) CVBS-1
VIC1 A/V Decoder ZiVA-3
MIC1 Main Micom TMP93CM41F
Video data
VIC52 Amplifier BA7660
CVBS-2 Y
VIC50 SAA7128
C
Video encoder
Y VIC51 Amplifier BA7660
Pr Pb
Fig. 6-21 Video Output Block Diagram
6-16
Samsung Electronics
Circuit Descriptions
6-6-2 NTSC/PAL Digital Encoder (VIC50 : SAA7128) VIC50 inputted from pin4 with 27MHz generates HSYNC and VSYNC which are based on video signal. Each HSYNC and VSYNC outputted from Pin8 and Pin7 are inputted to Pin157 and Pin158 of A/V decoder VIC1(ZIVA3). VIC1 is the synchronous signals with the video signal and control the output timing of 8bit video signal of ITUR601 format. (Pin180, 182, 184 ~ 189 (MSP)) 8bit data is inputted to Pin9(MSB) and Pin16 of VIC50 and the inputted data is demuxed with each 8bit of Y/R-Y/BY. The separate signal is encoded to NTSC or PAL by control of MIC1. The above signals, that is CVBS (Composite Video Burst Synchronized)(Pin30), S-Video (Y:Pin27, C:Pin24), Y/Pb/Pr(Pin27/Pin29/Pin23) and GB(Pin26/Pin29/Pin23). In course of encoding, 8bit data can extend to 10bit or more. To convert the extended data to quantization noise as possible, VIC50 adopts 10bit D/A converter. VIC50 perform video en-coding as well as copy protection. VIC1 (SSA7128) CR-CB
9~16
Demultiplexer
VDATA [7:0]
RGB encoding
Luminace processing
Y
Trap
VSYNC HSYNC 27M
7 8 4
Chrominance processor
MRST SDA SCL
40 42 41
CTRL+CFG register
Cloed captions CGMS
10-bit DAC
MACROVISION 7.0.1/6.1
30
CVBS
27
Y
24
C
23
Cr/R
26
G
29
Cb/B
Fig. 6-22
6-6-3 Amplifier (VIC51, VIC52 : BA7660) VIC51 and VIC52 are 6dB amplifier. Based on CVBS signal, the final output level must be 2Vpp without 75ohm terminal resistance. Because the level of video encoder output is only 1.1Vpp, the level is adjusted with the special amplifier. When mute of pin1 is high active, if the pin is floating and connected to power, the output signal is never outputted. CVBS, Y, C, Cr and Cb outputted from video encoder are inputted to VIC52 (Pin7, Pin2 and Pin4) and VIC51 (Pin7 and Pin4) respectively and outputted from VIC52 (Pin10, Pin15 and Pin13) and VIC51 (Pin10 and Pin 13). Pin9, Pin12 and Pin14 of VIC51 and VIC52 are feedback pin to SAG compensation(DC characteristic compensation of signal). Resistance(VR3-VR14) which is inserted to input terminal is bias resistance for input offset. The signal to which gain is adjusted by amplifier is outputted from jack via 75ohm.
Samsung Electronics
6-17
Circuit Descriptions
6-6-4 Scart Jack Output The AV1 of scart jacks is used for connecting a TV or other display devices and the AV2 for a VCR or other players. When the DVD player is turned on, the RGB, CVBS, or S-VIDEO is outputted to AV1 and CVBS to AV2. When the player is turned off, CVBS signal of the TV is inputted and CVBS or RGB of a VCR inputted via AV2 is outputted. In case of AV2, the reverse signal flow to that. Switching of power on/off is controlled by SCIC1, SCIC2, and SCIC5. The control signal (Pin 9,10,11) of SCIC1 and SCIC2 is outputted from PIN100 of FIC1 and connected to the signal(Pin 4) inverted by FIC3. The control signal(Pin 9,10,11) of SCIC5 is also outputted from Pin100 of FIC1 and inverted again by SCQ8. According to the characteristics that SCART Jack is supplied same pins for the output of CVBS signal and Y signal and for the R signal and C signal, SCIC3 lets the user select two signals in setup menu. This control signal (Pin 9,10,11) of the switch is outputted from Pin 92 of FIC1. The signal selected by switch is amplified by SIC4 and SIC6 and outputted through the SCART jack. The scart jack has the function select signal (Pin 8 of AV1) that the TV can select automatically RF and the external video signal. SCQ1 to SCQ7 are the circuit to point, FIC1 (Pin100, 94) controls. When the TV aspect ratio is 4/3 or 16/9, it is outputted 4.5 ~ 7V or 9.5 ~ 12V each. But, when the DVD video source is 16/9 and 16/9 wide is selected in setup menu, 4.5 ~ 7V is outputted. Otherwise, 9.5 ~ 12V is outputted. When the player is turned off, the TV works with function selection by output signal of VCR in relation of SCQ9 and SCQ10. RGB control signal (Pin 16 of AV1) is outputted that the TV can select between RGB and CVBS. SCQ11 ~ SCQ14 and SCQ17 are for RGB control and controlled by FIC1 (Pin91). When the player is turned off, receives VCR input (Pin 37 of AV2) and buffers in this circuit and then outputs to Pin 16 of AV1.
CVBS_TV_IN CVBS_VCR_IN
CVBS_S
Y_S SIC2 (14053) Switch
CVBS_TV_IN SIC1 (14053) Switch
C_S R_S
R_VCR_IN G_S G_VCR_IN B_S B_VCR_IN
SIC3 (14053) Switch
SIC4 (NJM2267) Amplifier CVBS_VCR_OUT
SIC5 (14053) Switch
R/C_TV_OUT SIC6 G_TV_OUT (BA7660) Amplifier B_TV_OUT
CVBS/Y_VCR_OUT R_TV_OUT G_TV_OUT
AV1 TV
B_TV_OUT
R_VCR_IN G_VCR_IN B_VCR_IN
AV2 VCR
CVBS_VCR_OUT
Fig. 6-23
6-18
Samsung Electronics
Circuit Descriptions
6-7 Audio 6-7-1 Outline The four data (Data 0~3) outputted from A/V decoder (VIC1 ; ZiVA-3) are supplied to DATA 0 for 2-channel mixed audio output and to DATA 1~3 for Analog audio output (5.1-channel). The audio data (0~3) transmitted from A/V decoder (VIC1 ; ZiVA-3) are converted into analog signal via audio D/A converter and outputted via post filter and amplifier. CD and VCD are outputted with only 2 channels audio data and transmit them to Data 0 and Data 1. Front L/R channel is outputted in mixed audio output (L/R output) and analog audio output and surround L/R, center and subwoofer arenÕt outputted. If DVD of 2 channels source disc is used, it is outputted by the same way with CD and VCD. If 5.1-channel source disc, front L/R channel is outputted in Data 1, Surround L/R in Data 2 and Center/Subwoofer in Data 3. At that time, 5.1 channel can be downmixed in 2 channel in Data 0. Mixed Audio Output (2-Channel) DATA0 LRCK BCK
AIC1 AK4324 D/A CONVERTER
POST FILTER POST FILTER
AIC2 AK4324 D/A CONVERTER
POST FILTER POST FILTER
AMP
FRONT-L
AMP
FRONT-R
AIC3 AK4324 D/A CONVERTER
POST FILTER POST FILTER
AMP
SURROUND-L
AMP
SURROUND-R
AIC4 AK4324 D/A CONVERTER
POST FILTER POST FILTER
AMP
CENTER
AMP
SUB WOOFER
AMP
L
AMP
R
Analog Audio Output (5.1-Channel) DATA1
VIC1 (ZiVA-3) A/V Decoder
DATA2
DATA3
Fig. 6-24 Audio Output Block Diagram
Samsung Electronics
6-19
Circuit Descriptions
6-7-2 DVD Audio Output Source Data Types : MPEG-1,-2, Dolby Digital, CD-DA, LPCM VIC4, 10 (LOCAL DRAM)
VIC1 (ZiVA-3 ; A/V DECODER) HOST or DVD/CD INTERFACE
IEC-958/1937 OUTPUT PROCESS
AUDIO INPUT BUFFER Compressed Data (MPEG, Dolby Digital), CD-DA, LPCM AUDIO DECODER (MPEG, DOLBY DIGITAL, CD-DA, LPCM
AUDIO OUTPUT BUFFER
IEC-958/1937 INTERFACE
RECEIVER or DECODER (IEC-958/1937)
2-Channel LPCM, Decoder Dolby Digital, Decoded MPEG
Uncompressed 16- or 24-bit LPCM camples at fs=44.1,48,96KHz 2-, 4, or 6CHANNEL OUTPUT PROCESS
DIGITAL AUDIO INTERFACE
AUDIO DAC
Fig. 6-25 Audio Decoder and Output Interface Datapath
1) Compressed Data The audio data inputted to VIC1 (ZiVA-3) A/V decoder is divided into compressed data and uncompressed data. It is compressed data that is compressed with multi-channel audio data such as Dolby digital, MPEG, DTS, etc. The compressed data inputted to VIC1 (ZiVA-3) is converted into the uncompressed data of 2, 4, and 6 channels through ZiVA-3 built-in audio decoder and is outputted to Data 0, 1, 2, and 3 through digital audio interface. The compressed data is transmitted to external AC-3 amplifier or MPEG/DTS amplifier as IEC-958/1937 transmission data format compressed by ZiVA-3 built-in IEC-958 output process.
2) Uncompressed Data The uncompressed data is that data isnÕt compressed, so it is called CD-DA, LPCM data. The 2 channels data is converted through audio decoder 2-channel data and Data 0 and Data 1 are outputted in digital audio interface.Via IEC-958 output process, they is transmitted to digital amplifier or AC-3/MPEG/DTS amplifier built in the external digital input source with IEC-958/1937 transmission format.
6-20
Samsung Electronics
Samsung Electronics
See "Fine Seek Check"
Yes
TE occurs in search range?
Yes
Actual velocity occurs at DRIC2-11, 12 terminal?
Yes
Actual velocity occurs at SIC1-73 terminal?
Yes
PS0, PS1 is input SIC1-2, 3 terminal from SIC8-1, 7?
No Search Operation
No
No
No
No
Focus On?
No
No
Replace Hall PCB
Check DRIC2 peripheral circuit.
Check SIC1 peripheral circuit.
Yes
0.1Vp-p sine wave occurs at search at SIC8-2, 6 terminal?
Check SIC8 peripheral circuit.
A
Check SIC1 peripheral circuit.
Yes
Pick-up transfer smooth.
Yes
TE is within 2V and 3V?
Yes
Track incomming is delayed?
Yes
TZCO signal (SIC1-52) is occurs?
Yes
FINE SEEK MIRR signal (RIC1-57) is missing?
FINE SEEK Check
Check SIC1 Peripheral curcuit.
Check RIC1 Peripheral curcuit.
No
Check RIC1-36 terminal.
No
Check DRIC2 peripheral circuit.
Check CN6 and pick-up.
Yes
DRIC2-17, 18 terminal outputs are normal?
Yes
SIC1-76 output is normal?
Time out due to many jump counts.
Check MECHA.
No
No
No
No
Yes
7. Troubleshooting
7-1
7-2
Check or replace disc motor.
Yes
DRIC1-23 signal MON is "H" ?
Yes
No
No
No
No
Yes
RIC1-86 output are normal?
Yes
RIC1-88 output is normal?
Check DRIC1 soldering and power.
Check DIC1, MIC1.
No
Check RIC1 peripheral circuit and A, B, C, D.
No
Check RIC1 soldering and power.
Check path to RIC1 and SIC1.
After resoldering SIC1.
DRIC1-24 output (FG) is normal?
Yes
SPD output is normal? (SIC1-74)
Yes
Input of RF signal is normal? (SIC1-59)
Abnormal rotation of disc motor
Check signal line state from DRIC1-26, 27 to tray motor.
Yes
Check DRIC2-26, 27 output at open/close
Yes
MIC1-84, 85 is Open ; "L", "L" ? Close ; "H", "H"?
No Tray open/close
No
No
Check DRIC2
Micom (MIC1) erroe.
Troubleshooting
Samsung Electronics
Samsung Electronics
A
No focus incoming and no disc occurs.
Yes
LD is outputted from object lens at play key input?
No Disc recognition
No B
Check open state from DRIC4 to pick-up.
Yes
DRIC4-1, 2 output are normal?
Yes
FE in SIC1-65 is within specified range?
A
No focus incoming
No
No
Check DRIC4
Check RIC1 and A, B, C, D input.
Troubleshooting
7-3
7-4
Check SIC1 soldering and power.
Yes
SELED FG Ps0, PS1 is input normally. (SIC1-2, 3)
No pick-up home positing
No Check SIC8, DRIC2 signal transfer system
Yes
RIC1-29 output is 200mV?
Yes
RIC1-28 is 5V?
LD out pick-up replace.
Yes
Current exceeds 0.1A?
Yes
Divide RQ1 emitter terminal voltage and 5V real voltage difference into 33ohm.
B
NO LD ON
No
Yes
Check MIC1
LD MPD error. Replace pick-up
Open check in related circuit.
No
No
RIC1-50 output is 0V?
No
Troubleshooting
Samsung Electronics
Samsung Electronics
Check AVJ2 peripheral soldering shot.
Yes
Base terminal level of AQ1, 2, 3, 4 are "L"?
Yes
AOP1-1, 7 output is normal?
Yes
Analog output of AIC1-16, 17, 18, 19 is normal?
Yes
Normal DATA 0 is input in AIC1-7?
CD/VCD/DVD L/R output error (Mixed Audio output)
No
No
No
No
Check FIC1-98 mute.
Check AOP1 peripheral circuit.
Check VIC1-169 (CD/VCD ; 16.9344MHz, DVD ; 18.432MHz)
Check VIC1-161 output.
Check AVJ3 peripheral soldering shot.
Yes
Base terminal level of AQ5, 6, 7, 8 are "L"?
Yes
AOP2-1, 7 output is normal?
Yes
Analog output of AIC2-16, 17, 18, 19 is normal?
Yes
Normal DATA 1 is input in AIC2-7?
Front L/R output error (Analog Audio output)
No
No
No
No
Check FIC1-98 mute.
Check AOP2 peripheral circuit.
Check VIC1-169 (CD/VCD ; 16.9344MHz, DVD ; 18.432MHz)
Check VIC1-163 output.
Troubleshooting
7-5
7-6
Check AVJ3 peripheral soldering shot.
Yes
Base terminal level of AQ9, 10, 11, 12 are "L"?
Yes
AOP3-1, 7 output is normal?
Yes
Analog output of AIC3-16, 17, 18, 19 is normal?
Yes
Normal DATA 2 is input in AIC3-7?
Yes
No
No
No
No
Check FIC1-97 mute.
Check AOP3 peripheral circuit.
Check VIC1-169 DVD ; 18.432MHz
Check VIC1-164 output.
Check AVJ3 peripheral soldering shot.
Yes
Base terminal level of AQ13, 14, 15, 16 are "L"?
Yes
AOP4-1, 7 output is normal?
Yes
Analog output of AIC4-16, 17, 18, 19 is normal?
Yes
Normal DATA 3 is input in AIC4-7?
Yes
5.1-channel is contained in playing disc?
Output only in 2-channel (stereo channel)
5.1-channel is contained in playing disc?
No
Center/Sub-Woofer output error (Analog Audio output)
Surround L/R output error (Analog Audio output)
No
No
No
No
No
Check FIC1-95, 96 mute.
Check AOP4 peripheral circuit.
Check VIC1-169 DVD ; 18.432MHz
Check VIC1-165 output.
Output only in 2-channel (stereo channel)
Troubleshooting
Samsung Electronics
Samsung Electronics
Check AVJ4 peripheral soldering shot.
Yes
Check VIC5.
Replace PIC1.
No
Pulse is missing in PIC1-5?
Yes
Voltage exists in PIC1-5?
Yes
PIC1 drain (pin 1) voltage is missing?
No
PD01 voltage is missing?
No
PF01 error?
Output in AIC5-6, 8, 10 is normal?
Check VIC1 peripheral circuit.
No
No
No Power (Standby LED OFF)
Yes
Output in VIC1-159 is normal?
Digital output error
Yes
No
No
Yes
Yes
Replace PIC1. Check feed back.
Check PR11, 12, 13, 14.
Check 2d voltage.
Check PR10.
Replace fuse.
Troubleshooting
7-7
7-8
If the problem persists ; Check after replacing Jack PCB, with another one. Check other parts for abnormal front operation persists.
Yes
Key of STOP, PLAY, OPEN work normally?
No
Operational waveform is missing in FIC3 (FLT) pin?
Yes
FIC1 soldering is OK?
Yes
Reset working in FIC1-12?
Yes
12MHz oscillation (FY1)?
Yes
REF +/-, 5V-all, -28V power is supplied.
No front (SET) operation
No
Yes
No
No
No
No
Check S/W interface. Check communication status with main micom (Check FIC1 pins 27, 72, 73, 74, 75)
Check FIC1 peripheral circuit.
Check FIC1 soldering.
Check reset peripheral circuit of FIC2.
Check X-TAL peripheral circuit.
Check power status.
VIC1 peripheral soldering and short check.
Yes
Signals are output from SIC1-42, 44?
Yes
27MHz clock is input in DIC1-14?
Yes
'NO DISK' appears after pick-up moves up and down twice at power on?
DVD play error
No
No
No
Replace SIC1.
Check 27MHz oscillating part.
Check DIC1, MIC1 peripheral short.
Troubleshooting
Samsung Electronics
Check A/V decoder signal process block.
Samsung Electronics
C
Yes
Play works?
Yes
/CS2, /RD, /WR signal occur?
Yes
All clocks (20MHz, 33.8688MHz, 27MHz) of main PCB oscillate normally?
Yes
No
No
No
Check VIC1 peripheral unit.
Yes
Check short pin out of micom common-bus (8-bit). Check short or operating of micom. Check soldering of micom and communication devices.
Yes
Check all clock oscillating parts.
Yes
Check eith article "No Front (SET) Operation"
No
MIC1-10, 19 waveform state (0, 1) changes whenever pressing front key?
No
MIC7-4, 5 pin is fixed to 0V?
No
MIC1-9 is fixed to 0V?
All power is measured correctly and front cable is properly connected? Yes
C
Key operation or remote control error
Yes
Yes
Yes
Check MIC1 peripheral soldering.
Check DVD signal process block.
Check A/V decoder signal process block.
Troubleshooting
7-9
7-10
D
Yes
Analog signals output normally at pin 30, 27, 24, 29, 23, in VIC50?
Yes
Video data are inputed normally at pin 9 ~ 16 in VIC50?
Yes
SYNC signal is normal at pin 7, 8 in VIC50?
Yes
Control signal is normal at pin 41, 42 in VIC50? (When power on or open)
Yes
MRST is high state at pin 40 in VIC50?
Yes
27MHz clock input is normal at pin 4 in VIC50?
Yes
Power level is normal at pin 6, 17, 20, 25, 28, 31, 36, 39 in VIC50?
Video output error in RCA Jacks
No
No
No
No
No
No
No
Change VIC50.
No
Check the soldering of VIC50.
Change VIC50.
No
Check the connection with pin 180, 182, 184 ~ 189 in VIC1.
Check the soldering of VIC50.
Check the connection between pin 86, 87 in MIC1 and pin 41, 42 in VIC50.
Check the connection between pin 1 in FIC1 and pin 40 in VIC50.
Check the connection between pin 10 in VIC6 and pin 4 in VIC50.
Check the connection between pin 2 in PIC6 and Emmiter in PQ24.
Check the RCA cable.
Yes
Video signals of about 1V appear at output jacks?
Yes
Video signals of about 2V appear at pin 10, 13, 15 in VIC51, 52?
Yes
Pin 1 in VIC51, 52 is in Low state?
Yes
Power is normal at pin 16 in VIC51, 52?
Yes
Analog signals are inputed normally at pin 2, 4, 7 in VIC51, 52?
D
No
No
No
No
No
Change VIC51, 52.
No
Check the connection between VIC51, 52 and output jacks.
Check the soldering of VIC51, 52.
Connect to ground.
Check the connection between VIC51, 52 and Emmiter of PQ24.
Check the connection between VIC50 and VIC51, 52.
Troubleshooting
Samsung Electronics
Samsung Electronics
Check the SCART cable.
Yes
CVBS signal is outputed at pin 19 in AV1?
Yes
CVBS signal is outputed at pin 5 in SCIC4?
Yes
CVBS signal is outputed at pin 14 in SCIC3?
Yes
CVBS signal is outputed at pin 14 in SCIC2?
Yes
CVBS signal is inputed at pin 12 in SCIC2?
Yes
Function select signal is 9.5~12V at pin 8 in AV1?
Yes
Video signal outputs normally in RCA jack?
No
No
No
No
No
No
No
Fix the TV ASPECT in setup menu to 4/3 LB. Connect to 4/3 ASPECT TV.
CVBS output error at AV1
Check the connection between pin 5 in SCIC4 and SCART jack.
Œ Check the connection between pin 14 in SCIC3 and pin 8 in SCIC4. ´ Check the power level at pin 7 in SCIC4.
Œ Check the connection between pin 14 in SCIC2 and pin 12 in SCIC3. ´ Check the connection between pin 9, 10, 11 in SCIC3 and pin 92 in FIC1 --> "L" stare.
Check the connection between pin 9, 10, 11 in SCIC2 and SCQ8 --> "L" state.
Check the connection with pin 30 in VIC50.
Check the connection between SCQ1~SCQ7 block and pin 100 in FIC1.
See "Video output error in RCA Jacks"
Check the SCART cable.
Yes
CVBS signal is outputed at pin 19 in AV2?
Yes
CVBS signal is outputed at pin 4 in SCIC4?
Yes
CVBS signal is outputed at pin 14 in SCIC1?
Yes
CVBS signal is inputed at pin 12 in SCIC1?
Yes
Video signal outputs normally in RCA jack?
CVBS output error at AV2
No
No
No
No
No
Check the connection between pin 4 in SCIC4 and SCART jack.
Œ Check the connection between pin 14 in SCIC3 and pin 8 in SCIC4. ´ Check the power level at pin 7 SCIC4.
Check the connection betweenpin 9, 10, 11 in SCIC2 and SCQ8 --> "L" state
Check the connection with pin 30 in VIC50.
See "Video output error in RCA Jacks"
Troubleshooting
7-11
7-12
Check the SCART cable.
Yes
RGB signal is outputed at pin 7, 11, 15 in AV1?
Yes
RGB signal is inputed at pin 2, 4, 7 in SCIC6?
Yes
RGB signal is outputed at pin 4, 13, 15 in SCIC5?
Yes
RGB signal is inputed at pin 1, 3, 13 in SCIC5?
Yes
R signal is outputed normally at pin 15 in SCIC3?
Yes
RGB signal is outputed at pin 23, 26, 29 in VIC50?
Yes
No
No
No
No
No
No
Check the connection with pin 10, 13, 15 in SCIC6.
Check the connection with pin 4, 13, 15 in SCIC5.
Check pin 9, 10, 11 in SCIC5 --> "H" state
Œ Check the connection between pin 5 in SCIC3 and pin 2 in SCIC5. ´ Check the connection between pin 26 in VIC50 and pin 13 in SCIC5. ˇ Check the connection between pin 29 in VIC50 and pin 3 in SCIC5.
Œ Check the connection between pin 23 in VIC50 and pin 2 in SCIC3. ´ Check the pin 9, 10, 11 in SCIC3 --> "L" state.
See "Video output error in RCA jacks"
See "CVBS output error at AV1" and "RGB output error at AV1".
Yes
Y, C signals are outputed at pin 14, 15 in SCIC3?
Yes
Y, C signals are inputed at pin 1, 13 in SCIC3?
Yes
S-VIDEO signals are outputed normally in the UPPER jack?
No
Y, C signals are outputed at pin 15, 19 in AV1?
Output voltage at pin in AV1 is in 1V ~ 3V? Check the pin 91 in FIC1 --> "H" state. Check SCQ 11, 12, 17 circuit.
Change the SCART output in setup menu to S-VIDEO.
Change the SCART output in setup menu to RGB.
No
S-Video output error at AV1
RGB output error at AV1
No
No
No
Yes
Check the pin 9, 10, 11 in SCIC3 --> "H" state.
Œ Check the connection between pin 27 in VIC50 and pin 13 in SCIC3. ´ Check the connection between pin 24 in VIC5 and pin 1 in SCIC3.
See "Video output error in RCA jacks"
Check the SCART cable. Check the TV which is capable accept S-VIDEO.
Troubleshooting
Samsung Electronics
8. Exploded View and Parts List Page 8-1 Cabinet Assembly (DVD-909) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-2 8-2 Cabinet Assembly (DVD-709) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-4 8-3 Deck Assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-6
Samsung Electronics
8-1
8-2
2
1
3
5
4
701
S.N.A
151
S.N.A. : Service Not Available
151
602 (ASSY-PCB-JACK)
151
702
151
11
13
12
CN11A
605
14
12
151
101
610
S.N.A. (CABINET-BOTTOM)
S.N.A. (CHASSIS-REAR)
601 (ASSY-PCB-MAIN)
151
150
S.N.A. (DECK-DVD MECHA)
UT01
150
150
Exploded Views and Parts List
8-1 Cabinet Assembly (DVD-909)
Samsung Electronics
Exploded Views and Parts List
Loc. No
Parts No.
1 2 3 4 5 11 12 13 14 101 150 151 601 602 605 610
Refer to table below Refer to table below Refer to table below Refer to table below Refer to table below AH61-00194A AH64-80001E AH61-00194B AH61-00194C Refer to table below Refer to table below 6003-000276 Refer to table below Refer to table below AH63-00040A AH39-00034A AH39-00129A AH39-00042A AH39-10002R AH39-00041A AH92-00169A AH92-00168A 3809-001133 Refer to table below
701 702 CN11A UT01
REGIONAL NUMBER 1 2
Description ; Specification
1
Remark
ASSY-CABINET FRONT;DVD-909,ASSY,EXPORT ASSY-DOOR TRAY;DVD-739,ABS,XAA KNOB-VOLUME;-,ABS94,HB,L/GRAY,-,DVD-909 KNOB-JOG;-,ABS94,HB,BLK,-,DVD-909 KNOB-SHUTTLE;-,ABS94,HB,BLK,-,DVD-909 HOLDER-DECK A;-,ABS 94HB,-,DVD-909 FOOT-FRONT;-,ABS94,HB,T2,SIL,H/STAMP,DVD HOLDER-DECK B;-,ABS 94HB,-,BLK,-,DVD-909 HOLDER-DECK C;-,ABS 94HB,-,BLK,-,DVD-909 ASSY-CABINET TOP;ABS, SCREW-TAPTITE;BH,+,B,M3,L10,SWCH1018 SCREW-TAPTITE;BH,+,B,M3,L10,ZPC(YEL),SWC ASSY-PCB-MAIN;DVD-909,MAIN PCB ASSY-PCB-JACK;DVD-909,JACK PCB GROUND-REAR;-,PBS,T0.2,-,DVD-909 POWER CORD;-,1.83M,CONNECTOR (EP-2) POWER CORD;-,1.83M,CONNECTOR POWER CORD;-,1.83M,CONNECTOR (BS) POWER CORD;-,1.83M,CONNECTOR (AP-2) POWER CORD;-,1.83M,CONNECTOR (CP-2) ASSY-PCB-PHONE POWER;DVD-909,PHONE ASSY-PCB-PLAY;DVD-909,PLAY CABLE-FLAT;30V,80C,200MM,35P,1.25MM,UL28 REMOCON-ASS’Y;-,-,-,48,DVD-909,S.S
2
3
4
5
101
NORTH AMERICA LATIN AMERICA U.K AUSTRALIA COMMON
150
601
602
UT01
AH95-10353K AH95-50369E AH64-11306C AH64-11346A AH64-11345A AH97-00188A 6003-000275 AH92-00052A AH92-00053A AH59-10141A
EUROPE
AH95-10353L AH95-50369A AH64-11306E AH64-11346B AH64-11345B AH97-00188C AH60-00025A AH92-00054A AH92-00055A AH59-10141B
TRKEY
AH95-10353H AH95-50369E AH64-11306C AH64-11346A AH64-11345A AH97-00188C AH60-00025A AH92-00054A AH92-00055A AH59-10141B
4
AH95-10353L AH95-50369A AH64-11306E AH64-11346B AH64-11345B AH97-00188C AH60-00025A AH92-00436A AH92-00437A AH59-10141B
5
AH95-10353L AH95-50369A AH64-11306E AH64-11346B AH64-11345B AH97-00188C AH60-00025A AH92-00413A AH92-00412A AH59-10141B
Samsung Electronics
8-3
8-4
1
2
701
702
151
S.N.A. : Service Not Available
151
602 (ASSY-PCB-JACK)
151
11
151
13
12
CN11A
605
14
12
151
101
610
S.N.A. (CABINET-BOTTOM)
S.N.A. (CHASSIS-REAR)
601 (ASSY-PCB-MAIN)
151
150
S.N.A. (DECK-DVD MECHA)
UT01
150
150
Exploded Views and Parts List
8-2 Cabinet Assembly (DVD-709)
Samsung Electronics
Exploded Views and Parts List
Loc. No
Parts No.
1 2 11 12 13 14 101 150 151 601 602 605 610
Description ; Specification
Refer to table below Refer to table below AH61-00194A AH64-80001E AH61-00194B AH61-00194C Refer to table below Refer to table below 6003-000276 Refer to table below Refer to table below AH63-00040A AH39-00034A AH39-00129A AH39-00042A AH39-10002R AH39-00041A AH92-00167A AH92-00166A 3809-001133 Refer to table below
701 702 CN11A UT01
Remark
ASSY-CABINET FRONT;DVD-709,ASSY,EXPORT ASSY-DOOR TRAY;DVD-709,ABS HOLDER-DECK A;-,ABS 94HB,-,DVD-909 FOOT-FRONT;-,ABS94,HB,T2,SIL,H/STAMP,DVD HOLDER-DECK B;-,ABS 94HB,-,BLK,-,DVD-909 HOLDER-DECK C;-,ABS 94HB,-,BLK,-,DVD-909 ASSY-CABINET TOP;DVD-709,ABS SCREW-TAPTITE;BH,+,B,M3,L10,BLK,SWCH1018 SCREW-TAPTITE;BH,+,B,M3,L10,ZPC(YEL),SWC ASSY-PCB-MAIN;DVD-709,MAIN PCB ASSY-PCB-JACK;DVD-709,JACK PCB GROUND-REAR;-,PBS,T0.2,-,DVD-909 POWER CORD;-,1.83M,CONNECTOR (EP-2) POWER CORD;-,1.83M,CONNECTOR POWER CORD;-,1.83M,CONNECTOR (BS) POWER CORD;-,1.83M,CONNECTOR (AP-2) POWER CORD;-,1.83M,CONNECTOR (CP-2) ASSY-PCB-POWER;DVD-709,POWER ASSY-PCB-PLAY;DVD-709,PLAY CABLE-FLAT;30V,80C,200MM,35P,1.25MM,UL28 REMOCON-ASS’Y;-,-,-,48,DVD-909,S.S
NORTH AMERICA LATIN AMERICA U.K AUSTRALIA COMMON
REGIONAL NUMBER
1
2
101
150
601
602
UT01
1
AH95-10355A
AH95-50369C
AH97-00188A
6003-000275
AH92-00056A
AH92-00057A
AH59-10141A
EUROPE
AH95-10355C
AH95-50369A
AH97-00188C
AH60-00025A
AH92-00058A
AH92-00059A
AH59-10141B
TRKEY
AH95-10355L
AH95-50369C
AH97-00188C
AH60-00025A
AH92-00058A
AH92-00059A
AH59-10141B
4
AH95-10355C
AH95-50369A
AH97-00188C
AH60-00025A
AH92-00450A
AH92-00273A
AH59-10141B
5
AH95-10355C
AH95-50369A
AH97-00188C
AH60-00025A
AH92-00439A
AH92-00440A
AH59-10141B
2
Samsung Electronics
8-5
Exploded Views and Parts List
8-3 Deck Assembly 903 225
903
903 225
225
903
224
215 906
S.N.A.
219
222 220
905 216
223
204 221 220
220
216
214
218 217 201
909
S.N.A.
212 901 211 907
901 210
206
213 908
209
208
S.N.A.
230 229 230
207 904
231 205 203 202 227
S.N.A. : Service Not Available 8-6
902
Samsung Electronics
Exploded Views and Parts List
Loc. No 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 227 229 230 231 901 902 903 904 905 906 907 908 909
Parts No. AH91-60117A AH92-00035A 3809-001125 AH91-60147A AH66-90054A AH91-60154A AH66-30087A AH66-20194A AH66-20183A AH66-20185A AH66-10024A AH66-60033A AH66-20184A AH97-00178A BG61-20031A AH61-50327A AH66-20228A AH30-20001B AH91-60151A AH60-30020A AH91-60120A AH66-20182A AH91-60121A AH63-30245B AH73-10017A 3809-001123 AH61-50323A AH66-22005A AH97-00179A AH60-10151A AC60-10051A AH60-10143U AH60-10145A AH60-10147A AC60-10059A AH60-00010A AC60-10042A BG60-10020A
Samsung Electronics
Description ; Specification
Remark
ASSY-DECK CLAMPER;DVD860,-,DP-1 ASSY-PCB-DECK;DP-3,CABLE-FLAT;30V,80C,140MM,8P,1MM,UL2896 ASSY-BRKT DECK;DP-3,DVD-909,TRAY-DVD;DP,ABS,-,BLK,-,DP-1 ASSY-DECK HOUSING;DP-3,DVD-909,LEVER-OPEN SW;DP,KEPITAL,T0.7,L26,F20-03 GEAR-CAM CENTER;DP,KEPITAL F20-03,M1.2,Z GEAR-CAM SUB;DP,KEPITAL FT2020,M1,2,Z7,GEAR-TRAY A;DP,KEPITAL F20-03,M0.4/M0.5, PULLEY-GEAR;DP,KEPITAL F20-03,BLK,DP-1 BELT-PULLEY;DP,CR,T1.5,0.08,L82.7,BLK,DP GEAR-TRAY;DP,KEPITAL F20-03,M0.5/M0.6,Z4 ASSY-BRKT FEED;DP-3,-,SOH-DP1 HOLDER-CAM;-,POM,-,-,-,DDR-4 SHAFT-P/U;DP,SUS420J2,OD3,L84.7,S/FINISH RACK-SLIDE;DP,KEPITAL F20-03,WHT,M0.4,P1 PICK-UP;SPU-DP1 DVD-909 ASSY-MOTOR SPINDLE;DP-3,DVD-909,WASHER-PLAIN;DP,-,ID3.1,OD6,T0.3,RED COL ASSY-GEAR-FEED-AU/AL;DP-1,DVD-860,GEAR-FEED B;DP,KEPITAL F20-03,M0.4,Z44,W ASSY-GEAR-FEED-CU/CL;DP-1,DVD-860,COVER-sheet;-,-,-,T0.7,CLR,-,BLK CARBON, RUBBER-INSULATOR;RUBBER(LB-40),OD11,DP-1 CABLE-FLAT;30V,80C,90MM,40P,1.25MM,UL289 SHAFT-SYNCRO;-,sus304,2.1,119,-,-,dvd-90 GEAR-SYNCRO-A;KEPITAL F20-03,M0.8,Z9,-,P ASSY-HOUSING MOTOR;DP-3,-,SOH-DP1 SCREW-TAP TITE;DP,SPEC6.8 ,PH,+,CP,M2,L SCREW-TAPPING;BH,-,-,M3,L8,FZY SCREW-TAP TITE;DP,PH,+,SPEC,TAP1.7,L5,ZP SCREW-TAP TITE;DP,PH,+,SPEC OD5.5 FP,TAP SCREW-MACHINE;DP,CH,+,FP,M2,L4,ZPC,SWRCH SCREW-TAPPING;BH,+,-,1.7,X5,ZPC2 SCREW-MACHINE-MOTOR;-,+,SWCH18AK,M1.7,L2 SCREW-TAPPING;PWH,+,-,M3,L8,SCREW-SP MOTOR;-,BHW TOOTH,-,-,M1.7,L3,-
8-7
Exploded Views and Parts List
MEMO
8-8
Samsung Electronics
9. Electrical Parts List Loc.No
Part No
601 AR1 AR2 AR3 AR4 AR5 AR6 AR7 AR8 AR9 CN6 CN7 CN8 DC1 DC10 DC11 DC12 DC13 DC14 DC15 DC16 DC2 DC23 DC24 DC3 DC4 DC5 DC6 DC7 DC8 DC9 DE1 DIC1 DIC2 DIC7 DL1 DRC1 DRC10 DRC11 DRC2 DRC3 DRC4 DRC5 DRC6 DRC7 DRC8 DRC9 DRE1 DRE2 DRE3 DRE4 DRE5 DRE6 DRE7 DRE8 DRE9 DRIC1 DRIC2 DRL1 DRL2
Description ; Specification
Remark
ASSY-PCB-MAIN 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000070 2007-000074 2007-000070 3708-001085 3711-003358 3708-001364 2203-000560 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-001567 2203-000189 2203-000560 2203-000189 2203-000189 2203-000560 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2401-002144 AH13-10030P 1105-001233 0801-002097 3301-000353 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2401-002075 2401-002075 2401-002075 2401-002144 2401-002144 2401-002144 2401-002144 2401-002144 2401-002144 1003-001130 1003-001067 3301-000353 3301-000353
Samsung Electronics
R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 CONNECTOR-FPC/FC/PIC;40P,1.25mm,STRAIGHT CONNECTOR-HEADER;BOX,8P,1R,2.5mm,STRAIGH CONNECTOR-FPC/FC/PIC;35P,1.25MM,STRAIGHT C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;10pF,0.5pF,50V,CH,1608,1. C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-AL;47uF,20%,16V,GP,TP,5x11,5 IC-ASIC;-,KS1453,TQFP,128P,DATA PRO. I IC-DRAM;416C256,256KX16BIT,SOJ,40P,400MI IC-CMOS LOGIC;7SET08,AND GATE,SOP,5P,110 CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-AL;4.7uF,20%,50V,GP,TP,5x11,5 C-AL;4.7uF,20%,50V,GP,TP,5x11,5 C-AL;4.7uF,20%,50V,GP,TP,5x11,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 IC-MOTOR DRIVER;KA3011DTF,SOP,28P,-,QUAD IC-MOTOR DRIVER;KA3010D,SOP,28P,375MIL,Q CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,-
Loc.No
Part No
DRR10 DRR11 DRR12 DRR13 DRR14 DRR3 DRR4 DRR7 DRR9 MC1 MC10 MC11 MC12 MC13 MC14 MC16 MC18 MC19 MC2 MC20 MC3 MC4 MC5 MC6 MC7 MC8 MC9 MIC1 MIC2 MIC5 MIC6 MIC7 MIC8 MIC8A ML1 MQ1 MR1 MR10 MR12 MR13 MR14 MR15 MR16 MR17 MR18 MR19 MR2 MR22 MR23 MR24 MR25 MR3 MR33 MR34 MR35 MR36 MR37 MR38 MR39 MR4 MR40 MR43
2007-000084 2007-000087 2007-000087 2007-000090 2007-000070 2007-007157 2007-007157 2007-001179 2007-000616 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-001656 2203-001656 2203-001656 2203-000189 2203-000189 2203-000426 2203-000426 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 0903-001144 0801-002207 1103-001133 0801-002143 0801-000379 S.N.A. 3704-000472 3301-000353 0504-000128 2007-000084 2007-000084 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000109 2007-000074 2007-000074 2007-000074 2007-000070 2007-000084 2007-000070 2007-000084 2007-000084 2007-000124 2007-000090 2007-000090 2007-000103 2007-000084 2007-000402 2007-000102
Description ; Specification
Remark
R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;6.8Kohm,5%,1/16W,DA,TP,1608 R-CHIP;6.8Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;1ohm,5%,1/4W,DA,TP,3216 R-CHIP;1ohm,5%,1/4W,DA,TP,3216 R-CHIP;8.2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;24Kohm,5%,1/16W,DA,TP,1608 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;470pF,5%,50V,CH,TP,1608,1 C-CERAMIC,CHIP;470pF,5%,50V,CH,TP,1608,1 C-CERAMIC,CHIP;470pF,5%,50V,CH,TP,1608,1 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;18pF,5%,50V,NPO,1608,-,TP C-CERAMIC,CHIP;18pF,5%,50V,NPO,1608,-,TP C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, IC-MICROCONTROLLER;93CM41,8BIT,QFP,100P, IC-CMOS LOGIC;74AC573,LATCH,SOP,20P,300M IC-EEPROM;24C020,256x8BIT,SOP,8P,150MIL, IC-CMOS LOGIC;7S32,OR GATE,SOT-25,5P,63M IC-CMOS LOGIC;74HC00,NAND GATE,SOP,14P,1 IC-EPROM;27C081,1MX8BIT,DIP,32P,600MIL,1 SOCKET-IC;32P,DIP,SN,2.54mm CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;1Mohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2.2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;120Kohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;150ohm,5%,1/16W,DA,TP,1608 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608
9-1
Electrical Parts List
Loc.No
Part No
MR5 MR6 MR7 MR8 MR9 MXTAL1 PC1 PC2 PC3 PC4 PE1 PE2 PE3 PE4 RC1 RC10 RC11 RC12 RC13 RC14 RC15 RC16 RC17 RC2 RC20 RC21 RC22 RC23 RC24 RC25 RC26 RC27 RC28 RC29 RC3 RC31 RC32 RC33 RC34 RC35 RC36 RC37 RC38 RC39 RC4 RC40 RC41 RC42 RC43 RC44 RC45 RC46 RC47 RC5 RC50 RC51 RC52 RC53 RC54 RC55 RC6 RC7 RC8 RC9 RD1 RD2
2007-000084 2007-000084 2007-000084 2007-000084 2007-000084 2801-000199 2203-000189 2203-000189 2203-000189 2203-000189 2401-002165 2401-002165 2401-002165 2401-002165 2203-000189 2203-000257 2203-000189 2203-000560 2203-000560 2203-000440 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000384 2203-000189 2203-000189 2203-001697 2203-000189 2203-000189 2203-000189 2203-001052 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000236 2203-000140 2203-000189 2203-000189 2203-000531 2203-000236 2203-000257 2203-000189 2203-000189 2203-000189 2203-000189 2203-001652 2203-000560 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000888 2203-001052 2203-001640 2203-000384 2203-000257 0401-000008 0403-001079
9-2
Description ; Specification R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 CRYSTAL-UNIT;20MHz,50ppm,28-AAA,16pF,50o C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-AL;100uF,20%,16V,GP,TP,6.3x7,5 C-AL;100uF,20%,16V,GP,TP,6.3x7,5 C-AL;100uF,20%,16V,GP,TP,6.3x7,5 C-AL;100uF,20%,16V,GP,TP,6.3x7,5 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;15pF,5%,50V,NPO,TP,1608,C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;.082NF,5%,50V,NPO,TP,1608 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;560pF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100pF,5%,50V,NPO,TP,1608, C-CERAMIC,CHIP;1.5nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;2.7nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;100pF,5%,50V,NPO,TP,1608, C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;470NF,+80-20%,16V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;4.7nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;560pF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;390pF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;15pF,5%,50V,NPO,TP,1608,C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608, DIODE-SWITCHING;DAN217,80V,100mA,SOT-23, DIODE-ZENER;UDZ3.9B,7%,200MW,SOD-323,TP
Remark
Loc.No RD6 RD7 RE10 RE11 RE12 RE13 RE17 RE2 RE8 RE9 RIC1 RIC2 RIC3 RIC4 RIC6 RL2 RL3 RL4 RQ1 RQ2 RR1 RR10 RR11 RR12 RR13 RR14 RR15 RR16 RR17 RR18 RR19 RR2 RR20 RR21 RR22 RR23 RR24 RR25 RR26 RR27 RR28 RR29 RR3 RR30 RR31 RR32 RR32A RR33 RR34 RR35 RR36 RR37 RR38 RR39 RR4 RR40 RR41 RR42 RR43 RR44 RR45 RR46 RR47 RR48 RR49 RR5
Part No 0407-000114 0407-000114 2401-002036 2401-000913 2401-002144 2401-000414 2401-002144 2401-000414 2401-000414 2401-002144 AH13-10030M 0801-002279 1202-000121 1201-000163 0801-002097 2703-000398 3301-000353 3301-000353 0501-000279 0504-000128 2007-000091 2007-001179 2007-000509 2007-000093 2007-001179 2007-000091 2007-001179 2007-000704 2007-000092 2007-000102 2007-000102 2007-000092 2007-000084 2007-000081 2007-000102 2007-000102 2007-000078 2007-000091 2007-000090 2007-000130 2007-000078 2007-000078 2007-000091 2007-000091 2007-001179 2007-000102 2007-000108 2007-000082 2007-000090 2007-000092 2007-000102 2007-000102 2007-000102 2007-000102 2007-000090 2007-000129 2007-000708 2007-000090 2007-000090 2007-000090 2007-000090 2007-000084 2007-000102 2007-000102 2007-000084 2007-001056
Description ; Specification
Remark
DIODE-ARRAY;DAN202K,80V,100mA,CA2-3,SOTDIODE-ARRAY;DAN202K,80V,100mA,CA2-3,SOTC-AL;1uF,20%,50V,GP,TP,5x11,2.5mm C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;10uF,20%,16V,GP,TP,4x7,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;10uF,20%,16V,GP,TP,4x7,5 C-AL;10uF,20%,16V,GP,TP,4x7,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 IC-ASIC;-,KS1461,VQFP,100P,RF IC IC-CMOS LOGIC;74VHC4053,MUX,SOP,16P,150M IC-VOLTAGE COMP.;2903,SOP,8P,150MIL,DUAL IC-OP AMP;4560,SOP,8P,150MIL,DUAL,100V/M IC-CMOS LOGIC;7SET08,AND GATE,SOP,5P,110 INDUCTOR-SMD;10UH,10%,3.2X2.5X2.2MM CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,TR-SMALL SIGNAL;KSA1182-Y,PNP,150mW,SOTTR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP R-CHIP;12Kohm,5%,1/16W,DA,TP,1608 R-CHIP;8.2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2.4Kohm,1%,1/16W,DA,TP,1608 R-CHIP;20Kohm,5%,1/16W,DA,TP,1608 R-CHIP;8.2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;12Kohm,5%,1/16W,DA,TP,1608 R-CHIP;8.2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;3.6Kohm,5%,1/16W,DA,TP,1608 R-CHIP;15Kohm,5%,1/16W,DA,TP,1608 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608 R-CHIP;15Kohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;12Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;39Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;12Kohm,5%,1/16W,DA,TP,1608 R-CHIP;12Kohm,5%,1/16W,DA,TP,1608 R-CHIP;8.2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608 R-CHIP;510Kohm,5%,1/16W,DA,TP,1608 R-CHIP;3.3Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;15Kohm,5%,1/16W,DA,TP,1608 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;27Kohm,5%,1/16W,DA,TP,1608 R-CHIP;3.9Kohm,1%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;6.2Kohm,5%,1/16W,DA,TP,1608
Samsung Electronics
Electrical Parts List
Loc.No RR50 RR51 RR52 RR53 RR56 RR57 RR58 RR59 RR6 RR62 RR63 RR65 RR67 RR68 RR69 RR69A RR7 RR70 RR71 RR8 RR9 SC1 SC10 SC11 SC14 SC15 SC16 SC17 SC18 SC19 SC2 SC20 SC21 SC26 SC29 SC3 SC30 SC31 SC32 SC33 SC34 SC36 SC37 SC38 SC39 SC4 SC5 SC6 SC7 SC9 SD2 SD3 SE1 SE2 SE3 SE4 SE5 SIC1 SIC2 SIC3 SIC8 SL2 SL3 SL4 SQ1 SR1
Part No 2007-000084 2007-000134 2007-000084 2007-001179 2007-000084 2007-000088 2007-000091 2007-000082 2007-000092 2007-000084 2007-000090 2007-000082 2007-000092 2007-000129 2007-000091 2007-000431 2007-000072 2007-000134 2007-000070 2007-000077 2007-000783 2203-000189 2203-001222 2203-000189 2203-000491 2203-000491 2203-000189 2203-000560 2203-000189 2203-000140 2203-001573 2203-000189 2203-001567 2203-002398 2203-000372 2203-001573 2203-000372 2203-000491 2203-000491 2203-000560 2203-000405 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000560 0407-000114 0407-000114 2401-002144 2401-002144 2401-002144 2401-000240 2401-000913 AH13-10030N 0801-002097 0801-002097 1202-000121 3301-000353 3301-000353 3301-000353 0504-000128 2007-000090
Samsung Electronics
Description ; Specification R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;33Kohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;8.2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;7.5Kohm,5%,1/16W,DA,TP,1608 R-CHIP;12Kohm,5%,1/16W,DA,TP,1608 R-CHIP;3.3Kohm,5%,1/16W,DA,TP,1608 R-CHIP;15Kohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;3.3Kohm,5%,1/16W,DA,TP,1608 R-CHIP;15Kohm,5%,1/16W,DA,TP,1608 R-CHIP;27Kohm,5%,1/16W,DA,TP,1608 R-CHIP;12Kohm,5%,1/16W,DA,TP,1608 R-CHIP;16Kohm,5%,1/16W,DA,TP,1608 R-CHIP;47ohm,5%,1/16W,DA,TP,1608 R-CHIP;33Kohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;470ohm,5%,1/16W,DA,TP,1608 R-CHIP;33OHM,5%,1/8W,DA,TP,3216 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;820pF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;2.2nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;2.2nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;1.5nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;12pF,5%,50V,CH,1608,1.6mm C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;10pF,0.5pF,50V,CH,1608,1. C-CERAMIC,CHIP;22nF,10%,50V,X7R,TP,1608, C-CERAMIC,CHIP;15nF,10%,50V,X7R,TP,1608, C-CERAMIC,CHIP;12pF,5%,50V,CH,1608,1.6mm C-CERAMIC,CHIP;15nF,10%,50V,X7R,TP,1608, C-CERAMIC,CHIP;2.2nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;2.2nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;180pF,5%,50V,NPO,TP,1608, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, DIODE-ARRAY;DAN202K,80V,100mA,CA2-3,SOTDIODE-ARRAY;DAN202K,80V,100mA,CA2-3,SOTC-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;100uF,20%,10V,GP,TP,5x11,5 C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m IC-ASIC;-,KS1452,QFP,80P,DSSP IC IC-CMOS LOGIC;7SET08,AND GATE,SOP,5P,110 IC-CMOS LOGIC;7SET08,AND GATE,SOP,5P,110 IC-VOLTAGE COMP.;2903,SOP,8P,150MIL,DUAL CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP R-CHIP;10Kohm,5%,1/16W,DA,TP,1608
Remark
Loc.No SR10 SR11 SR12 SR13 SR14 SR15 SR16 SR17 SR18 SR19 SR2 SR20 SR21 SR22 SR23 SR24 SR26 SR3 SR31 SR32 SR33 SR34 SR35 SR36 SR37 SR38 SR39 SR4 SR40 SR42 SR44 SR45 SR46 SR47 SR48 SR49 SR5 SR50 SR51 SR52 SR53 SR54 SR6 SR7 SR8 SR9 SY1 VC1 VC10 VC11 VC12 VC13 VC14 VC15 VC16 VC17 VC18 VC19 VC20 VC21 VC22 VC23 VC24 VC25 VC26 VC27
Part No 2007-000084 2007-000107 2007-001235 2007-000070 2007-000450 2007-000102 2007-000131 2007-000093 2007-000093 2007-000092 2007-000109 2007-000092 2007-000070 2007-000070 2007-000130 2007-000070 2007-000091 2007-000090 2007-000080 2007-000080 2007-000080 2007-000124 2007-000124 2007-000124 2007-000124 2007-000092 2007-000458 2007-001179 2007-000090 2007-000090 2007-000078 2007-000078 2007-000078 2007-000078 2007-000109 2007-000109 2007-000084 2007-000082 2007-000082 2007-000704 2007-000123 2007-000077 2007-000098 2007-000799 2007-000070 2007-000084 2801-000261 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189
Description ; Specification
Remark
R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;470Kohm,5%,1/16W,DA,TP,1608 R-CHIP;910Kohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;180ohm,5%,1/16W,DA,TP,1608 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608 R-CHIP;91Kohm,5%,1/16W,DA,TP,1608 R-CHIP;20Kohm,5%,1/16W,DA,TP,1608 R-CHIP;20Kohm,5%,1/16W,DA,TP,1608 R-CHIP;15Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Mohm,5%,1/16W,DA,TP,1608 R-CHIP;15Kohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;39Kohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;12Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2.2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2.2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2.2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2.2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;15Kohm,5%,1/16W,DA,TP,1608 R-CHIP;18Kohm,5%,1/16W,DA,TP,1608 R-CHIP;8.2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Mohm,5%,1/16W,DA,TP,1608 R-CHIP;1Mohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;3.3Kohm,5%,1/16W,DA,TP,1608 R-CHIP;3.3Kohm,5%,1/16W,DA,TP,1608 R-CHIP;3.6Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1.5Kohm,5%,1/16W,DA,TP,1608 R-CHIP;470ohm,5%,1/16W,DA,TP,1608 R-CHIP;56Kohm,5%,1/16W,DA,TP,1608 R-CHIP;360ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 CRYSTAL-UNIT;33.8688MHZ,50PPM,28-AAA,12P C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP,
9-3
Electrical Parts List
Loc.No VC28 VC29 VC3 VC30 VC31 VC32 VC33 VC34 VC35 VC36 VC37 VC38 VC39 VC4 VC40 VC41 VC42 VC43 VC44 VC45 VC47 VC48 VC5 VC50 VC51 VC52 VC53 VC54 VC55 VC6 VC61 VC62 VC65 VC66 VC67 VC68 VC69 VC7 VC70 VC71 VC72 VC73 VC74 VC75 VC76 VC77 VC78 VC8 VC81 VC82 VC83 VC84 VC85 VC9 VE1 VE2 VIC1 VIC10 VIC10 VIC3 VIC4 VIC4 VIC6 VL1 VL10 VL11
9-4
Part No 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000560 2203-000560 2203-000560 2203-000560 2203-000189 2203-000560 2203-000560 2203-000189 2203-000189 2203-000189 2203-000189 2203-000626 2203-000681 2203-000189 2203-000560 2203-000560 2203-000560 2203-000560 2203-000560 2203-000560 2203-000189 2203-001636 2203-001636 2203-001636 2203-001636 2203-001636 2203-001636 2203-000626 2203-000189 2203-000626 2203-000626 2203-000626 2203-000626 2203-000626 2203-000626 2203-000626 2203-000626 2203-000626 2203-000189 2203-000851 2203-000851 2203-001071 2203-000236 2203-000236 2203-000189 2401-002165 2401-002165 1204-001438 1105-001165 1105-001259 0801-002097 1105-001165 1105-001259 AH14-10004R 3301-000353 2007-000029 3301-000353
Description ; Specification C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;22pF,5%,50V,NPO,TP,1608,C-CERAMIC,CHIP;27pF,5%,50V,NPO,1608,-,TP C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;33pF,5%,50V,NPO,TP,1608,1 C-CERAMIC,CHIP;33pF,5%,50V,NPO,TP,1608,1 C-CERAMIC,CHIP;33pF,5%,50V,NPO,TP,1608,1 C-CERAMIC,CHIP;33pF,5%,50V,NPO,TP,1608,1 C-CERAMIC,CHIP;33pF,5%,50V,NPO,TP,1608,1 C-CERAMIC,CHIP;33pF,5%,50V,NPO,TP,1608,1 C-CERAMIC,CHIP;22pF,5%,50V,NPO,TP,1608,C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;22pF,5%,50V,NPO,TP,1608,C-CERAMIC,CHIP;22pF,5%,50V,NPO,TP,1608,C-CERAMIC,CHIP;22pF,5%,50V,NPO,TP,1608,C-CERAMIC,CHIP;22pF,5%,50V,NPO,TP,1608,C-CERAMIC,CHIP;22pF,5%,50V,NPO,TP,1608,C-CERAMIC,CHIP;22pF,5%,50V,NPO,TP,1608,C-CERAMIC,CHIP;22pF,5%,50V,NPO,TP,1608,C-CERAMIC,CHIP;22pF,5%,50V,NPO,TP,1608,C-CERAMIC,CHIP;22pF,5%,50V,NPO,TP,1608,C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;39pF,5%,50V,NPO,TP,1608,C-CERAMIC,CHIP;39pF,5%,50V,NPO,TP,1608,C-CERAMIC,CHIP;56pF,5%,50V,NPO,TP,1608,C-CERAMIC,CHIP;100pF,5%,50V,NPO,TP,1608, C-CERAMIC,CHIP;100pF,5%,50V,NPO,TP,1608, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-AL;100uF,20%,16V,GP,TP,6.3x7,5 C-AL;100uF,20%,16V,GP,TP,6.3x7,5 IC-DECODER;ZIVA-3,VQFP,208P,1098MIL,PLAS IC-SDRAM;416S1020,512Kx16BITx2,TSOP,50P IC-DRAM;416S1020,16BIT,TSOP,50P,400MIL,8 IC-CMOS LOGIC;7SET08,AND GATE,SOP,5P,110 IC-SDRAM;416S1020,512Kx16BITx2,TSOP,50P IC-DRAM;416S1020,16BIT,TSOP,50P,400MIL,8 IC;M74HCU04,SOP,TAPE 14P CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,R-CHIP;0OHM,5%,1/10W,DA,TP,2012 CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,-
Remark
NTSC PAL NTSC PAL
Loc.No VL12 VL13 VL14 VL15 VL16 VL17 VL18 VL19 VL2 VL20 VL21 VL22 VL23 VL24 VL25 VL26 VL27 VL28 VL29 VL3 VL4 VL5 VL6 VR10 VR100 VR101 VR102 VR103 VR104 VR2 VR21 VR22 VR23 VR24 VR25 VR26 VR27 VR28 VR3 VR30 VR31 VR32 VR33 VR34 VR35 VR36 VR37 VR38 VR39 VR4 VR40 VR41 VR42 VR43 VR44 VR45 VR46 VR47 VR48 VR49 VR50 VR51 VR52 VR54 VR55 VR56
Part No 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 2007-000084 2007-001134 2007-001134 2007-000113 2007-000113 2007-000113 2007-000084 2007-000090 2007-000090 2007-000090 2007-000090 2007-000090 2007-000090 2007-000090 2007-000090 2007-000074 2007-000113 2007-000113 2007-000113 2007-000113 2007-000113 2007-000113 2007-000113 2007-000113 2007-000113 2007-000113 2007-000084 2007-000113 2007-000113 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000070
Description ; Specification
Remark
CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;33ohm,5%,1/16W,DA,TP,1608 R-CHIP;33ohm,5%,1/16W,DA,TP,1608 R-CHIP;33ohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10Kohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;33ohm,5%,1/16W,DA,TP,1608 R-CHIP;33ohm,5%,1/16W,DA,TP,1608 R-CHIP;33ohm,5%,1/16W,DA,TP,1608 R-CHIP;33ohm,5%,1/16W,DA,TP,1608 R-CHIP;33ohm,5%,1/16W,DA,TP,1608 R-CHIP;33ohm,5%,1/16W,DA,TP,1608 R-CHIP;33ohm,5%,1/16W,DA,TP,1608 R-CHIP;33ohm,5%,1/16W,DA,TP,1608 R-CHIP;33ohm,5%,1/16W,DA,TP,1608 R-CHIP;33ohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;33ohm,5%,1/16W,DA,TP,1608 R-CHIP;33ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608
Samsung Electronics
Electrical Parts List
Loc.No VR57 VR58 VR59 VR60 VR61 VR62 VR63 VR64 VR65 VR66 VR67 VR68 VR69 VR7 VR70 VR71 VR72 VR73 VR74 VR75 VR76 VR77 VR78 VR79 VR80 VR81 VR82 VR83 VR84 VR85 VR86 VR87 VR88 VR89 VR9 VR90 VR91 VR92 VR93 VR94 VR95 VR96 VR97 VR98 VR99 VY1
Part No 2007-000070 2007-000075 2007-000075 2007-000075 2007-000075 2007-000075 2007-000075 2007-000075 2007-000075 2007-000074 2007-000074 2007-000074 2007-000074 2007-000116 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000402 2007-001134 2007-001134 2007-001134 2007-001134 2007-001134 2007-001134 2007-001134 2007-000109 2007-001134 2007-001134 2007-001134 2007-001134 2007-001134 2007-001134 2007-001134 2007-001134 2007-001134 2007-000070 2801-003554
Samsung Electronics
Description ; Specification R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;220ohm,5%,1/16W,DA,TP,1608 R-CHIP;220ohm,5%,1/16W,DA,TP,1608 R-CHIP;220ohm,5%,1/16W,DA,TP,1608 R-CHIP;220ohm,5%,1/16W,DA,TP,1608 R-CHIP;220ohm,5%,1/16W,DA,TP,1608 R-CHIP;220ohm,5%,1/16W,DA,TP,1608 R-CHIP;220ohm,5%,1/16W,DA,TP,1608 R-CHIP;220ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;120ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;150ohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;1Mohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 CRYSTAL-UNIT;27MHz,10ppm,28-AAM,12pF,40o
Remark
Loc.No
602 AC1 AC10 AC11 AC12 AC16 AC17 AC18 AC19 AC2 AC20 AC21 AC22 AC23 AC25 AC26 AC27 AC29 AC3 AC30 AC31 AC32 AC33 AC34 AC35 AC36 AC38 AC39 AC4 AC40 AC42 AC43 AC44 AC45 AC46 AC47 AC48 AC49 AC5 AC51 AC52 AC53 AC56 AC57 AC58 AC59 AC6 AC60 AC61 AC7 AC71 AC73 AC74 AC75 AC76 AC77 AC78 AC79 AC8 AC80 AC90 AC91 AC92 AC93
Part No
Description ; Specification
Remark
ASSY-PCB-JACK 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, 2203-000444 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,2012,2202-000806 C-CERAMIC,MLC-AXIAL;220pF,10%,50V,Y5P,TP 2203-000595 C-CERAMIC,CHIP;220pF,5%,50V,NPO,TP,2012, 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, DVD-909 ONLY 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, DVD-909 ONLY 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V, DVD-909 ONLY 2203-000444 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,2012,- DVD-909 ONLY 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, 2203-000595 C-CERAMIC,CHIP;220pF,5%,50V,NPO,TP,2012, DVD-909 ONLY 2203-000595 C-CERAMIC,CHIP;220pF,5%,50V,NPO,TP,2012, DVD-909 ONLY 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, DVD-909 ONLY 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, DVD-909 ONLY 2203-000444 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,2012,- DVD-909 ONLY 2202-000806 C-CERAMIC,MLC-AXIAL;220pF,10%,50V,Y5P,TP DVD-909 ONLY 2203-000595 C-CERAMIC,CHIP;220pF,5%,50V,NPO,TP,2012, DVD-909 ONLY 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, DVD-909 ONLY 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, DVD-909 ONLY 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V DVD-909 ONLY 2203-000444 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,2012,DVD-909 ONLY 2203-000595 C-CERAMIC,CHIP;220pF,5%,50V,NPO,TP,2012, DVD-909 ONLY 2203-000595 C-CERAMIC,CHIP;220pF,5%,50V,NPO,TP,2012, DVD-909 ONLY 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, DVD-909 ONLY 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, DVD-909 ONLY 2203-000444 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,2012,- DVD-909 ONLY 2202-000806 C-CERAMIC,MLC-AXIAL;220pF,10%,50V,Y5P,TP DVD-909 ONLY 2203-000444 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,2012,2203-000595 C-CERAMIC,CHIP;220pF,5%,50V,NPO,TP,2012, DVD-909 ONLY 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, DVD-909 ONLY 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, DVD-909 ONLY 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, DVD-909 ONLY 2203-000444 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,2012,- DVD-909 ONLY 2203-000595 C-CERAMIC,CHIP;220pF,5%,50V,NPO,TP,2012, DVD-909 ONLY 2203-000595 C-CERAMIC,CHIP;220pF,5%,50V,NPO,TP,2012, DVD-909 ONLY 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, DVD-909 ONLY 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, DVD-909 ONLY 2203-000595 C-CERAMIC,CHIP;220pF,5%,50V,NPO,TP,2012, 2203-000444 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,2012,- DVD-909 ONLY 2202-000806 C-CERAMIC,MLC-AXIAL;220pF,10%,50V,Y5P,TP DVD-909 ONLY 2203-000595 C-CERAMIC,CHIP;220pF,5%,50V,NPO,TP,2012, DVD-909 ONLY 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, DVD-909 ONLY 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V 2203-000595 C-CERAMIC,CHIP;220pF,5%,50V,NPO,TP,2012, 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V DVD-909 ONLY 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, 2301-000161 C-FILM,PEF;12nF,5%,50V,6.5X5.5X3.0X5,5mm 2301-000161 C-FILM,PEF;12nF,5%,50V,6.5X5.5X3.0X5,5mm 2301-000161 C-FILM,PEF;12nF,5%,50V,6.5X5.5X3.0X5,5mm DVD-909 ONLY 2301-000161 C-FILM,PEF;12nF,5%,50V,6.5X5.5X3.0X5,5mm DVD-909 ONLY 2301-000161 C-FILM,PEF;12nF,5%,50V,6.5X5.5X3.0X5,5mm DVD-909 ONLY 2301-000161 C-FILM,PEF;12nF,5%,50V,6.5X5.5X3.0X5,5mmDVD-909 ONLY 2301-000161 C-FILM,PEF;12nF,5%,50V,6.5X5.5X3.0X5,5mm DVD-909 ONLY 2203-000192 C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, 2301-000161 C-FILM,PEF;12nF,5%,50V,6.5X5.5X3.0X5,5mm DVD-909 ONLY 2202-000849 C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. 2202-000849 C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. DVD-909 ONLY 2202-000849 C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. DVD-909 ONLY 2202-000849 C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. DVD-909 ONLY
9-5
Electrical Parts List
Loc.No AC94 AC95 AC98 AD1 AD10 AD12 AD13 AD14 AD15 AD2 AD3 AD4 AD5 AD6 AD7 AD8 AD9 AE1 AE10 AE11 AE12 AE13 AE14 AE15 AE16 AE17 AE18 AE19 AE2 AE20 AE21 AE22 AE23 AE24 AE25 AE26 AE27 AE28 AE29 AE3 AE30 AE31 AE32 AE33 AE34 AE35 AE36 AE37 AE38 AE39 AE4 AE40 AE5 AE6 AE7 AE8 AE9 AIC1 AIC2 AIC3 AIC4 AIC5 AL1 AL11 AL12 AL15
9-6
Part No 2202-000849 2202-000849 2203-000361 0407-000114 0407-000114 0407-000114 0407-000114 0407-000114 0407-000114 0407-000114 0407-000116 0401-000101 0401-000101 0407-000114 0407-000114 0407-000114 0407-000114 2401-002042 2401-002144 2401-002144 2401-002042 2401-002042 2401-002042 2401-002068 2401-002068 2401-000913 2401-002068 2401-002068 2401-002042 2401-000913 2401-002042 2401-002042 2401-002042 2401-002068 2401-002068 2401-000913 2401-002068 2401-002068 2401-000913 2401-002042 2401-000302 2401-001969 2401-002042 2401-002042 2401-002042 2401-002068 2401-002068 2401-000913 2401-002068 2401-002068 2401-002068 2401-000913 2401-002068 2401-000913 2401-002068 2401-002068 2401-000913 1002-001129 1002-001129 1002-001129 1002-001129 AH14-10004R 3301-000353 3301-000353 3301-000353 3301-000353
Description ; Specification
Remark
C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. C-CERAMIC,CHIP;150pF,5%,50V,NPO,TP,2012, DIODE-ARRAY;DAN202K,80V,100mA,CA2-3,SOTDIODE-ARRAY;DAN202K,80V,100mA,CA2-3, DVD-909 ONLY DIODE-ARRAY;DAN202K,80V,100mA,CA2-3 DVD-909 ONLY DIODE-ARRAY;DAN202K,80V,100mA,CA2-3, DVD-909 ONLY DIODE-ARRAY;DAN202K,80V,100mA,CA2-3, DVD-909 ONLY DIODE-ARRAY;DAN202K,80V,100mA,CA2-3, DVD-909 ONLY DIODE-ARRAY;DAN202K,80V,100mA,CA2-3,SOTDIODE-ARRAY;DAP202K,80V,100mA,CK2-3, DVD-909 ONLY DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-ARRAY;DAN202K,80V,100mA,CA2-3,SOTDIODE-ARRAY;DAN202K,80V,100mA,CA2-3,SOTDIODE-ARRAY;DAN202K,80V,100mA,CA2-3, DVD-909 ONLY DIODE-ARRAY;DAN202K,80V,100mA,CA2-3, DVD-909 ONLY C-AL;220uF,20%,10V,GP,TP,6.3x11,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;220uF,20%,10V,GP,TP,6.3x11,5 DVD-909 ONLY C-AL;220uF,20%,10V,GP,TP,6.3x11,5 DVD-909 ONLY C-AL;220uF,20%,10V,GP,TP,6.3x11,5 DVD-909 ONLY C-AL;33uF,20%,16V,GP,TP,5x11,5 DVD-909 ONLY C-AL;33uF,20%,16V,GP,TP,5x11,5 DVD-909 ONLY C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m DVD-909 ONLY C-AL;33uF,20%,16V,GP,TP,5x11,5 DVD-909 ONLY C-AL;33uF,20%,16V,GP,TP,5x11,5 DVD-909 ONLY C-AL;220uF,20%,10V,GP,TP,6.3x11,5 C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m DVD-909 ONLY C-AL;220uF,20%,10V,GP,TP,6.3x11,5 DVD-909 ONLY C-AL;220uF,20%,10V,GP,TP,6.3x11,5 DVD-909 ONLY C-AL;220uF,20%,10V,GP,TP,6.3x11,5 DVD-909 ONLY C-AL;33uF,20%,16V,GP,TP,5x11,5 DVD-909 ONLY C-AL;33uF,20%,16V,GP,TP,5x11,5 DVD-909 ONLY C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m DVD-909 ONLY C-AL;33uF,20%,16V,GP,TP,5x11,5 DVD-909 ONLY C-AL;33uF,20%,16V,GP,TP,5x11,5 DVD-909 ONLY C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m DVD-909 ONLY C-AL;220uF,20%,10V,GP,TP,6.3x11,5 C-AL;100uF,20%,25V,GP,TP,6.3x11,5 C-AL;470uF,20%,25V,GP,TP,10x12.5,5 C-AL;220uF,20%,10V,GP,TP,6.3x11,5 DVD-909 ONLY C-AL;220uF,20%,10V,GP,TP,6.3x11,5 DVD-909 ONLY C-AL;220uF,20%,10V,GP,TP,6.3x11,5 DVD-909 ONLY C-AL;33uF,20%,16V,GP,TP,5x11,5 DVD-909 ONLY C-AL;33uF,20%,16V,GP,TP,5x11,5 DVD-909 ONLY C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m DVD-909 ONLY C-AL;33uF,20%,16V,GP,TP,5x11,5 DVD-909 ONLY C-AL;33uF,20%,16V,GP,TP,5x11,5 DVD-909 ONLY C-AL;33uF,20%,16V,GP,TP,5x11,5 C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m DVD-909 ONLY C-AL;33uF,20%,16V,GP,TP,5x11,5 C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m C-AL;33uF,20%,16V,GP,TP,5x11,5 C-AL;33uF,20%,16V,GP,TP,5x11,5 C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m IC-D/A CONVERTER;AK4324VF,24BIT,VSOP,24P IC-D/A CONVERTER;AK4324VF,24BIT,VSOP,24P DVD-909 ONLY IC-D/A CONVERTER;AK4324VF,24BIT,VSOP,24P DVD-909 ONLY IC-D/A CONVERTER;AK4324VF,24BIT,VSOP,24P DVD-909 ONLY IC;M74HCU04,SOP,TAPE 14P CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,DVD-909 ONLY CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,DVD-909 ONLY CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,DVD-909 ONLY
Loc.No AL16 AL19 AL2 AL20 AL21 AL22 AL5 AL6 AL7 AL8 AOP1 AOP2 AOP3 AOP4 AOP5 AQ1 AQ10 AQ11 AQ12 AQ13 AQ14 AQ15 AQ16 AQ17 AQ18 AQ19 AQ2 AQ20 AQ21 AQ22 AQ23 AQ24 AQ25 AQ26 AQ27 AQ28 AQ29 AQ3 AQ30 AQ31 AQ32 AQ33 AQ4 AQ5 AQ6 AQ7 AQ8 AQ9 AR1 AR10 AR100 AR101 AR104 AR106 AR107 AR108 AR109 AR11 AR110 AR111 AR112 AR113 AR116 AR118 AR119 AR12
Part No 3301-000353 2901-001125 3301-000353 2901-001125 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 3301-000353 1201-000163 1201-000163 1201-000163 1201-000163 1201-000163 0501-000341 0501-000341 0501-000341 0501-000341 0501-000341 0501-000341 0501-000341 0501-000341 0504-000118 0504-000118 0504-001003 0501-000341 0504-000156 0504-000128 0504-000156 0504-000128 0504-000156 0504-000128 0504-000156 0504-000128 0504-000156 0504-000128 0501-000341 0504-000156 0504-000128 0504-000156 0504-000128 0501-000341 0501-000341 0501-000341 0501-000341 0501-000341 0501-000341 2007-000290 2001-000878 2007-001055 2001-000290 2001-000429 2007-000766 2001-000878 2001-000878 2001-000331 2001-000878 2007-001055 2007-001055 2007-000355 2001-000290 2001-000429 2007-000766 2007-000766 2007-001055
Description ; Specification
Remark
CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,DVD-909 ONLY FILTER-EMI ON BOARD;50V,0.5A,-,220pF,7x7 CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,FILTER-EMI ON BOARD;50V,0.5A,-,220pF,7x7 DVD-909 ONLY CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,DVD-909 ONLY CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,DVD-909 ONLY CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,DVD-909 ONLY CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,DVD-909 ONLY IC-OP AMP;4560,SOP,8P,150MIL,DUAL,100V/M IC-OP AMP;4560,SOP,8P,150MIL,DUAL,100V/M DVD-909 ONLY IC-OP AMP;4560,SOP,8P,150MIL,DUAL,100V/M DVD-909 ONLY IC-OP AMP;4560,SOP,8P,150MIL,DUAL,100V/M DVD-909 ONLY IC-OP AMP;4560,SOP,8P,150MIL,DUAL,100V/M TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOTTR-SMALL SIGNAL;KSC1623-L,NPN,200mW, DVD-909 ONLY TR-SMALL SIGNAL;KSC1623-L,NPN,200mW, DVD-909 ONLY TR-SMALL SIGNAL;KSC1623-L,NPN,200mW, DVD-909 ONLY TR-SMALL SIGNAL;KSC1623-L,NPN,200mW, DVD-909 ONLY TR-SMALL SIGNAL;KSC1623-L,NPN,200mW, DVD-909 ONLY TR-SMALL SIGNAL;KSC1623-L,NPN,200mW, DVD-909 ONLY TR-SMALL SIGNAL;KSC1623-L,NPN,200mW, DVD-909 ONLY TR-DIGITAL;KSR1003,NPN,300MW,22K/22K,TOTR-DIGITAL;KSR1003,NPN,300MW,22K/22K,TOTR-DIGITAL;KSR2003,PNP,300MW,22K/22K,TOTR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOTTR-DIGITAL;DTA124EKA,PNP,200mW,22K-22K TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP TR-DIGITAL;DTA124EKA,PNP,200mW,22K-22K TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP DVD-909 ONLY TR-DIGITAL;DTA124EKA,PNP,200mW,22K-22K DVD-909 ONLY TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP DVD-909 ONLY TR-DIGITAL;DTA124EKA,PNP,200mW,22K-22K DVD-909 ONLY TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP DVD-909 ONLY TR-DIGITAL;DTA124EKA,PNP,200mW,22K-22K DVD-909 ONLY TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP DVD-909 ONLY TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOTTR-DIGITAL;DTA124EKA,PNP,200mW,22K-22K DVD-909 ONLY TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP DVD-909 ONLY TR-DIGITAL;DTA124EKA,PNP,200mW,22K-22K DVD-909 ONLY TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOTTR-SMALL SIGNAL;KSC1623-L,NPN,200mW, DVD-909 ONLY TR-SMALL SIGNAL;KSC1623-L,NPN,200mW, DVD-909 ONLY TR-SMALL SIGNAL;KSC1623-L,NPN,200mW, DVD-909 ONLY TR-SMALL SIGNAL;KSC1623-L,NPN,200mW, DVD-909 ONLY TR-SMALL SIGNAL;KSC1623-L,NPN,200mW, DVD-909 ONLY R-CHIP;100OHM,5%,1/10W,DA,TP,2012 R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3. DVD-909 ONLY R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3. DVD-909 ONLY R-CHIP;330OHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3. DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3. DVD-909 ONLY R-CARBON;12KOHM,5%,1/8W,AA,TP,1.8X3. DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CHIP;12KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3. DVD-909 ONLY R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3. DVD-909 ONLY R-CHIP;330OHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CHIP;330OHM,5%,1/10W,DA,TP,2012 R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012
Samsung Electronics
Electrical Parts List
Loc.No
Part No
AR121 AR13 AR130 AR131 AR132 AR133 AR134 AR138 AR14 AR15 AR150 AR151 AR152 AR153 AR154 AR155 AR156 AR18 AR19 AR2 AR20 AR21 AR22 AR23 AR24 AR25 AR26 AR27 AR28 AR29 AR30 AR31 AR32 AR33 AR34 AR35 AR36 AR37 AR38 AR39 AR40 AR41 AR42 AR43 AR44 AR45 AR46 AR47 AR48 AR49 AR50 AR51 AR52 AR53 AR54 AR55 AR56 AR57 AR58 AR59 AR60 AR61 AR62 AR63 AR64 AR65
2007-001247 2007-001055 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2007-000029 2007-001055 2001-000290 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000281 2001-000003 2001-000878 2001-000878 2001-000878 2007-001055 2007-001055 2007-001055 2007-000300 2001-000003 2001-000281 2001-000429 2001-000429 2007-000766 2007-000308 2001-000878 2001-000878 2001-000878 2007-001055 2007-001055 2007-001055 2007-000300 2001-000003 2001-000281 2001-000429 2001-000429 2007-000766 2001-000878 2001-000878 2001-000878 2007-001055 2007-001055 2007-001055 2007-000300 2001-000003 2001-000281 2001-000429 2001-000429 2007-000766 2007-000308 2001-000878 2001-000878 2001-000878 2007-001055 2007-001055 2007-001055 2007-000300
Samsung Electronics
Description ; Specification
Remark
R-CHIP;91OHM,5%,1/10W,DA,TP,2012 R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3. DVD-909 ONLY R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3. DVD-909 ONLY R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3. DVD-909 ONLY R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CHIP;0OHM,5%,1/10W,DA,TP,2012 R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;330OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 R-CHIP;10KOHM,5%,1/10W,DA,TP,2012 R-CARBON;330OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CHIP;330OHM,5%,1/10W,DA,TP,2012 R-CHIP;10OHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CHIP;10KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CARBON;330OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CHIP;330OHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CHIP;10KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CARBON;330OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CHIP;330OHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CHIP;10OHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CHIP;10KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY
Loc.No AR66 AR67 AR68 AR69 AR70 AR71 AR72 AR73 AR74 AR75 AR76 AR77 AR78 AR79 AR8 AR80 AR81 AR82 AR83 AR84 AR85 AR86 AR87 AR88 AR89 AR9 AR90 AR91 AR92 AR93 AR94 AR95 AR96 AR97 AR98 AR99 AVJ1 AVJ2 AVJ3 AVJ4 AVJ5 AZD1 CN11 CN12 CN15 CN17 CN18 FC1 FC10 FC14 FC15 FC16 FC2 FC3 FC4 FC6 FD10 FD6 FD7 FD8 FD9 FE1 FE12 FE13 FE2 FE5
Part No 2001-000003 2001-000281 2001-000429 2001-000429 2007-000766 2001-000878 2001-000878 2001-000878 2007-001055 2007-001055 2007-001055 2007-000300 2001-000003 2001-000281 2007-000308 2001-000429 2001-000429 2007-000766 2001-000003 2001-000281 2001-000429 2001-000003 2001-000281 2001-000429 2001-000003 2001-000878 2001-000241 2001-000281 2001-000281 2001-000281 2007-000308 2001-000878 2001-000878 2001-000878 2007-001055 2007-001055 3722-001355 3722-001353 3722-001352 3722-001053 3707-001005 0403-000551 3708-000277 AH39-00035A 3711-000665 AH39-00037A 3711-000967 2202-002037 2202-002037 2202-002037 2202-002037 2202-000173 2203-000389 2203-000389 2202-002037 2202-002037 0401-000101 0401-000101 0401-000101 0401-000101 0403-000551 2401-000913 2401-000240 2401-000240 2401-002144 2401-002144
Description ; Specification
Remark
R-CARBON;330OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CHIP;330OHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CHIP;10KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CARBON;330OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CHIP;10OHM,5%,1/10W,DA,TP,2012 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CHIP;330OHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CARBON;330OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;330OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;330OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3 R-CARBON;1.5KOHM,5%,1/8W,AA,TP,1.8X3 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CHIP;10OHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;6.2KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY R-CHIP;6.2KOHM,5%,1/10W,DA,TP,2012 DVD-909 ONLY JACK-RCA;3P(4P),3.2MM,NI,GRN/RED/ DVD-909 NTSC ONLY JACK-RCA;6P,3.2MM,NI,YEL/WHT/RED,DVD-909 ONLY JACK-RCA;6P,3.2MM,NI,BLK/WHT/RED,DVD-909 ONLY JACK-RCA;1P,3.2mm,NI,BLK,CONNECTOR-OPTICAL;PLUG,SM,-,4.4/2.0MM DVD-909 ONLY DIODE-ZENER;MTZ3.9B,3.9V,3.89-4.16V,500m CONNECTOR-FPC/FC/PIC;35P,1.25mm,ANGLE,SN LEAD CONNECTOR-ASSY;-,5264-08,35023-08,8 CONNECTOR-HEADER;BOX,12P,1R,2mm,ANGLE DVD-909 ONLY LEAD CONNECTOR-ASSY;-,51004-06,35023-06, DVD-909 ONLY CONNECTOR-HEADER;BOX,4P,1R,2mm,ANGLE,SN C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V C-CERAMIC,MLC-AXIAL;1nF,10%,50V,Y5P,TP,1 C-CERAMIC,CHIP;15pF,5%,50V,NPO,TP,2012,C-CERAMIC,CHIP;15pF,5%,50V,NPO,TP,2012,C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-ZENER;MTZ3.9B,3.9V,3.89-4.16V,500m C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m C-AL;100uF,20%,10V,GP,TP,5x11,5 C-AL;100uF,20%,10V,GP,TP,5x11,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;47uF,20%,16V,GP,TP,5x11,5
9-7
Electrical Parts List
Loc.No FE8 FIC1 FIC2 FIC3 FIC4 FL1 FL2 FR1 FR10 FR101 FR102 FR103 FR104 FR105 FR106 FR11 FR12 FR13 FR16 FR17 FR18 FR19 FR20 FR21 FR24 FR25 FR26 FR31 FR32 FR33 FR34 FR35 FR36 FR37 FR43 FR44 FR45 FR46 FR5 FR53 FR54 FR57 FR58 FR59 FY1 HC01 HC01 HC02 HC02 HR03 HR04 JP203 JP204 JP211 JP213 JP214 JP215 JP216 JP217 JP219 JP220 JP221 JP224 JP226 JP228 JP229
9-8
Part No 2401-002144 AH09-00010A 1203-001252 0801-002166 AH59-60010A 2701-000114 2701-000113 2001-000273 2001-000281 2001-000273 2001-000273 2001-000273 2001-000273 2001-000273 2001-000273 2001-000281 2001-000281 2001-000281 2001-000027 2001-000027 2001-000449 2001-000449 2001-000449 2001-000435 2001-000281 2001-000780 2001-000281 2007-000282 2007-000282 2007-000282 2007-000282 2007-000282 2007-000282 2007-000282 2001-000793 2001-000429 2001-000429 2001-000273 2001-000325 2001-000273 2001-000273 2001-000290 2007-000029 2007-000029 2802-000108 2401-002299 2401-002075 2401-002299 2401-002075 2001-000273 2001-000273 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033
Description ; Specification
Remark
C-AL;47uF,20%,16V,GP,TP,5x11,5 IC-MICOM MASKING;LC866232,100PIN,QIP,FLT IC-VOL. DETECTOR;7545,TO-92,3P,-,PLASTIC IC-CMOS LOGIC;7SHU04,INVERTER,SSOP,5P,63 MODULE-REMOCON;-,GP1U281Q,38KHZ,940,MESH INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm INDUCTOR-AXIAL;100uH,5%,2.5x3.4mm R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/4W,AA,TP,2.4X6.4MM R-CARBON;100OHM,5%,1/4W,AA,TP,2.4X6.4MM R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1MOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CHIP;100KOHM,5%,1/10W,DA,TP,2012 R-CHIP;100KOHM,5%,1/10W,DA,TP,2012 R-CHIP;100KOHM,5%,1/10W,DA,TP,2012 R-CHIP;100KOHM,5%,1/10W,DA,TP,2012 R-CHIP;100KOHM,5%,1/10W,DA,TP,2012 R-CHIP;100KOHM,5%,1/10W,DA,TP,2012 R-CHIP;100KOHM,5%,1/10W,DA,TP,2012 R-CARBON;47OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;120OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3 PAL ONLY R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3 NTSC ONLY R-CHIP;0OHM,5%,1/10W,DA,TP,2012 R-CHIP;0OHM,5%,1/10W,DA,TP,2012 RESONATOR-CERAMIC;12MHZ,0.5%,BK,10.0X5.0 C-AL;4.7uF,20%,50V,GP,TP,5x7,5 NTSC C-AL;4.7uF,20%,50V,GP,TP,5x11,5 PAL C-AL;4.7uF,20%,50V,GP,TP,5x7,5 NTSC C-AL;4.7uF,20%,50V,GP,TP,5x11,5 PAL R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 DVD-909 PAL ONLY R-CHIP;0OHM,5%,1/8W,DA,TP,3216 DVD-909 ONLY R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 DVD-909 PAL ONLY R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 PAL ONLY R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 DVD-909 PAL ONLY
Loc.No JP230 JP231 JP232 JP233 JP236 JP238 JP239 JP240 JP242 JP246 JP312 JP317 JP324 JP325 JP97 PC01 PC02 PC04 PC05 PC07 PC09 PC10 PC11 PC12 PC13 PC14 PC15 PC44 PCN01 PCN01 PD01 PD02 PD03 PD04 PD11 PD12 PD3 PD31 PD32 PD33 PD34 PD35 PD37 PD38 PE10 PE11 PE12 PE13 PE3 PE31 PE32 PE33 PE35 PE36 PE37 PE38 PE39 PE4 PE41 PE42 PE43 PE44 PE6 PF0A PF0A PIC1
Part No 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2305-001021 2305-001021 2301-000140 2201-000129 2301-000129 2301-000415 2201-000916 2201-000916 2203-000575 2203-000575 2203-000575 2203-000575 2301-000129 3711-000178 3711-000190 0402-001009 0402-001009 0402-001009 0402-001009 0402-000378 0402-001013 0402-001013 0402-001013 0402-000430 0402-001251 0402-001251 0402-001013 0402-000132 0402-000132 2401-001353 2401-000302 2401-000302 2401-000302 2401-001682 2401-000302 2401-001998 2401-001998 2401-000360 2401-001998 2401-001134 2401-002144 2401-001134 2401-000302 2401-002036 2401-002144 2401-002144 2401-002036 2401-001583 3601-000403 3601-001123 1203-001721
Description ; Specification
Remark
R-CHIP;0OHM,5%,1/8W,DA,TP,3216 PAL ONLY R-CHIP;0OHM,5%,1/8W,DA,TP,3216 DVD-909 PAL ONLY R-CHIP;0OHM,5%,1/8W,DA,TP,3216 DVD-909 PAL ONLY R-CHIP;0OHM,5%,1/8W,DA,TP,3216 DVD-909 PAL ONLY R-CHIP;0OHM,5%,1/8W,DA,TP,3216 DVD-909 PAL ONLY R-CHIP;0OHM,5%,1/8W,DA,TP,3216 PAL ONLY R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 DVD-909 PAL ONLY R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 C-FILM,MPEF;100nF,20%,275V,TP,17.5x7x13. C-FILM,MPEF;100nF,20%,275V,TP,17.5x7x13. C-FILM,PEF;10nF,10%,630V,BK,16.5X9.5X5.7 C-CERAMIC,DISC;100pF,10%,1KV,Y5P,TP,6x5, C-FILM,PEF;100nF,5%,50V,TP,10X9X4.3X5,5m C-FILM,PEF;22nF,5%,50V,TP,6.5x10.5x4mm,5 C-CERAMIC,DISC;100pF,10%,400V,Y5U,TP,10x C-CERAMIC,DISC;100pF,10%,400V,Y5U,TP,10x C-CERAMIC,CHIP;220NF,10%,25V,X7R,TP,2012 C-CERAMIC,CHIP;220NF,10%,25V,X7R,TP,2012 C-CERAMIC,CHIP;220NF,10%,25V,X7R,TP,2012 C-CERAMIC,CHIP;220NF,10%,25V,X7R,TP,2012 C-FILM,PEF;100nF,5%,50V,TP,10X9X4.3X5,5m CONNECTOR-HEADER;1WALL,2P,1R,3.96mm,STRA NTSC CONNECTOR-HEADER;1WALL,2P,1R,7.92mm,STRA PAL DIODE-RECTIFIER;1SR139,600V,1A,MSR,TP DIODE-RECTIFIER;1SR139,600V,1A,MSR,TP DIODE-RECTIFIER;1SR139,600V,1A,MSR,TP DIODE-RECTIFIER;1SR139,600V,1A,MSR,TP DIODE-RECTIFIER;EG01C,1000V,500mA,DO-41 DIODE-RECTIFIER;1SR153-400,400V,800mA,DO DIODE-RECTIFIER;1SR153-400,400V,800mA,DO DIODE-RECTIFIER;1SR153-400,400V,800mA,DO DIODE-RECTIFIER;FML-G02S,200V,3.0A,TO-22 DIODE-RECTIFIER;FMG-22R,200V,10A,TO-220F DIODE-RECTIFIER;FMG-22R,200V,10A,TO-220F DIODE-RECTIFIER;1SR153-400,400V,800mA,DO DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP C-AL;470uF,20%,10V,GP,TP,8x11.5,5 C-AL;100uF,20%,25V,GP,TP,6.3x11,5 C-AL;100uF,20%,25V,GP,TP,6.3x11,5 C-AL;100uF,20%,25V,GP,TP,6.3x11,5 C-AL;82uF,20%,400V,GP,BK,22x25,10mm C-AL;100uF,20%,25V,GP,TP,6.3x11,5 C-AL;1000uF,20%,25V,GP,TP,10x20,5mm C-AL;1000uF,20%,25V,GP,TP,10x20,5mm C-AL;100uF,20%,50V,GP,TP,8x11.5,5 C-AL;1000uF,20%,25V,GP,TP,10x20,5mm C-AL;330uF,20%,35V,WT,TP,10x16,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;330uF,20%,35V,WT,TP,10x16,5 C-AL;100uF,20%,25V,GP,TP,6.3x11,5 C-AL;1uF,20%,50V,GP,TP,5x11,2.5mm C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;47uF,20%,16V,GP,TP,5x11,5 C-AL;1uF,20%,50V,GP,TP,5x11,2.5mm C-AL;47uF,20%,50V,WT,TP,6.3x11,5 FUSE-FERRULE;250V,1.6A,SLOW-BLOW,GLASS,5 NTSC FUSE-FERRULE;250V,1.6A,TIME-LAG,CERAMIC, PAL IC-PWM CONTROLLER;STR-G6153T,T0-220,5P,1
Samsung Electronics
Electrical Parts List
Loc.No PIC2 PIC3 PIC4 PIC5 PIC6 PL01 PL02 PL03 PL11 PQ1 PQ2 PQ21 PQ22 PQ23 PQ24 PQ3 PQ4 PR10 PR11 PR12 PR13 PR14 PR15 PR16 PR17 PR18 PR2 PR20 PR3 PR31 PR32 PR33 PR34 PR35 PR36 PR37 PR38 PR39 PR4 PR40 PR5 PR6 PR7 PT01 PVA01 PZD31 RC12 RC13 RL03 SCC1 SCC10 SCC11 SCC12 SCC13 SCC14 SCC2 SCC3 SCC4 SCC5 SCC6 SCC7 SCC8 SCC9 SCD1 SCD2 SCD3
Part No 0604-000186 AC14-12006D 1203-000122 1203-001697 1203-001083 AC29-30050A AC27-92001Q 3301-000297 3301-000297 0501-000398 0501-000616 0504-000142 0504-000118 0502-000298 0502-000298 0504-000118 0504-000142 2006-000262 2001-000073 2001-000073 2001-000073 2001-000073 2003-000273 2003-000273 2003-000148 2001-000666 2003-000148 2001-000429 2001-000734 2001-000034 2001-000429 2001-000429 2001-000440 2001-000362 2001-000221 2001-000429 2004-000869 2004-000459 2001-000429 2003-000111 2001-000281 2001-000429 2001-000429 AH26-00008A 1405-000186 0403-000717 2201-000812 2201-000812 3301-000297 2203-000192 2203-000239 2202-002037 2203-000192 2202-002037 2203-000192 2203-000192 2202-000121 2202-000121 2202-000121 2202-000121 2203-000239 2203-000239 2203-000239 0407-000114 0407-000114 0407-000114
Samsung Electronics
Description ; Specification
Remark
PHOTO-COUPLER;TR,-,200mW,DIP-4,ST IC;KA431Z,TO-92,TAPING IC-NEGA.FIXED REG.;7908,TO-220,3P,-,PLAS IC-VOLTAGE REGULATOR;78R08,TO-220,4P,-,P IC-VOLTAGE REGULATOR;3RF23,TO-202,4P,12. FILTER-LINE NOISE;-,400UH,-,250V,COIL-LINE FILTER;BSF-2120Z,25MH,-,-,CORE-FERRITE BEAD;AA,3.6x1.2x5.7mm,1400, CORE-FERRITE BEAD;AA,3.6x1.2x5.7mm,1400, TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92 NTSC ONLY TR-SMALL SIGNAL;KSC2328A-Y,NPN,1W,TO-92L NTSC ONLY TR-DIGITAL;KSR2001,PNP,300MW,4.7K/4.7K,T TR-DIGITAL;KSR1003,NPN,300MW,22K/22K,TOTR-POWER;KSD73,NPN,30W,TO-220,-,120-240 TR-POWER;KSD73,NPN,30W,TO-220,-,120-240 TR-DIGITAL;KSR1003,NPN,300MW,22K/22K,TO- NTSC ONLY TR-DIGITAL;KSR2001,PNP,300MW,4.7K/4.7K,T NTSC ONLY R-CEMENT;2.7ohm,10%,2W,CB,ST,7.5x11x20. R-CARBON;33KOHM,5%,1/4W,AA,TP,2.4X6.4MM R-CARBON;33KOHM,5%,1/4W,AA,TP,2.4X6.4MM R-CARBON;33KOHM,5%,1/4W,AA,TP,2.4X6.4MM R-CARBON;33KOHM,5%,1/4W,AA,TP,2.4X6.4MM R-METAL OXIDE;33Kohm,5%,2W,AA,TP,6x16mm R-METAL OXIDE;33Kohm,5%,2W,AA,TP,6x16mm R-METAL OXIDE;100OHM,5%,2W,AE,TP,6X16MM R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM R-METAL OXIDE;100OHM,5%,2W,AE,TP,6X16MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3 NTSC ONLY R-CARBON;220OHM,5%,1/4W,AA,TP,2.4X6.4MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;150OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-METAL;3Kohm,1%,1/8W,AA,TP,1.8x3.2mm R-METAL;2.2Kohm,1%,1/8W,AA,TP,1.8x3.2m R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3 NTSC ONLY R-METAL OXIDE;0.47ohm,5%,1W,AD,TP,4.3x12 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3 NTSC ONLY R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3 NTSC ONLY R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM PAL ONLY TRANS-SWITCHING;-,85V-240V,UL/CSA,EE2821 VARISTOR;470V,4500A,17x12mm,TP DIODE-ZENER;MTZJ5.1B,5.1V,4.94-5.2V,500m C-CERAMIC,DISC;2.2nF,20%,400V,Y5U,BK,11x C-CERAMIC,DISC;2.2nF,20%,400V,Y5U,BK,11x CORE-FERRITE BEAD;AA,3.6x1.2x5.7mm,1400, C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V, DVD-909 PAL ONLY C-CERAMIC,CHIP;100pF,5%,50V,NPO, DVD-909 PAL ONLY C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V PAL ONLY C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, PAL ONLY C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V, DVD-909 PAL ONLY C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, PAL ONLY C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V DVD-909 PAL ONLY C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP PAL ONLY C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP PAL ONLY C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P DVD-909 PAL ONLY C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P, DVD-909 PAL ONLY C-CERAMIC,CHIP;100pF,5%,50V,NPO,TP, DVD-909 PAL ONLY C-CERAMIC,CHIP;100pF,5%,50V,NPO,TP, DVD-909 PAL ONLY C-CERAMIC,CHIP;100pF,5%,50V,NPO,TP, DVD-909 PAL ONLY DIODE-ARRAY;DAN202K,80V,100mA,CA2- DVD-909 PAL ONLY DIODE-ARRAY;DAN202K,80V,100mA,CA2-3,SOT- PAL ONLY DIODE-ARRAY;DAN202K,80V,100mA,CA2-3,SOT- PAL ONLY
Loc.No SCE1 SCE10 SCE11 SCE12 SCE13 SCE14 SCE15 SCE16 SCE17 SCE2 SCE3 SCE4 SCE5 SCE6 SCE7 SCE8 SCE9 SCIC1 SCIC2 SCIC3 SCIC4 SCIC5 SCIC6 SCJ1 SCL1 SCL10 SCL11 SCL2 SCL3 SCL4 SCQ1 SCQ10 SCQ11 SCQ12 SCQ13 SCQ14 SCQ17 SCQ18 SCQ19 SCQ2 SCQ3 SCQ4 SCQ5 SCQ6 SCQ7 SCQ8 SCQ9 SCR1 SCR10 SCR11 SCR12 SCR13 SCR14 SCR15 SCR16 SCR17 SCR18 SCR19 SCR2 SCR20 SCR21 SCR22 SCR23 SCR24 SCR25 SCR26
Part No 2401-002075 2401-000369 2401-000913 2401-000369 2401-000913 2401-000369 2401-000913 2401-002042 2401-001353 2401-000913 2401-000369 2401-002075 2401-000913 2401-000369 2401-002144 2401-002144 2401-002144 AH14-10004T AH14-10004T AH14-10004T 1201-001063 AH14-10004T 1201-001419 3722-001354 2701-000181 3301-000353 3301-000353 2701-000181 2701-000181 2701-000181 0504-000128 0504-000156 0504-000128 0504-000156 0504-000128 0504-000156 0501-000341 0501-000341 0501-000341 0504-000156 0504-000128 0504-000128 0501-000314 0501-000341 0501-000314 0504-000128 0504-000128 2001-000734 2007-001118 2001-000281 2001-000958 2001-000281 2001-000780 2001-000969 2001-000281 2001-000958 2001-000969 2001-000857 2007-000981 2001-000857 2001-000857 2001-000857 2007-001201 2007-001201 2007-001166 2007-001201
Description ; Specification
Remark
C-AL;4.7uF,20%,50V,GP,TP,5x11,5 DVD-909 PAL ONLY C-AL;100UF,20%,6.3V,GP,-,6.3X11,5 PAL ONLY C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m PAL ONLY C-AL;100UF,20%,6.3V,GP,-,6.3X11,5 PAL ONLY C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m PAL ONLY C-AL;100UF,20%,6.3V,GP,-,6.3X11,5 PAL ONLY C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m PAL ONLY C-AL;220uF,20%,10V,GP,TP,6.3x11,5 PAL ONLY C-AL;470uF,20%,10V,GP,TP,8x11.5,5 PAL ONLY C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m DVD-909 PAL ONLY C-AL;100UF,20%,6.3V,GP,-,6.3X11,5 DVD-909 PAL ONLY C-AL;4.7uF,20%,50V,GP,TP,5x11,5 PAL ONLY C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m PAL ONLY C-AL;100UF,20%,6.3V,GP,-,6.3X11,5 PAL ONLY C-AL;47uF,20%,16V,GP,TP,5x11,5 PAL ONLY C-AL;47uF,20%,16V,GP,TP,5x11,5 PAL ONLY C-AL;47uF,20%,16V,GP,TP,5x11,5 PAL ONLY IC-ANALOG M/PLEXER;MC14053BD,SOP, DVD-909 PAL ONLY IC-ANALOG M/PLEXER;MC14053BD,SOP, DVD-909 PAL ONLY IC-ANALOG M/PLEXER;MC14053BD,SOP,TAPE 16 PAL ONLY IC-OP AMP;2267,SOP,8P,300MIL,DUAL,6.7dB, PAL ONLY IC-ANALOG M/PLEXER;MC14053BD,SOP, DVD-909 PAL ONLY IC-VIDEO AMP;7660,SSOP,16P,173MIL,3,6DB, PAL ONLY JACK-SCART;42P/2R,-,SN,BLK,PAL ONLY INDUCTOR-AXIAL;33UH,5%,2.4X3.4MM PAL ONLY CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,PAL ONLY CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,PAL ONLY INDUCTOR-AXIAL;33UH,5%,2.4X3.4MM PAL ONLY INDUCTOR-AXIAL;33UH,5%,2.4X3.4MM DVD-909 PAL ONLY INDUCTOR-AXIAL;33UH,5%,2.4X3.4MM DVD-909 PAL ONLY TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP PAL ONLY TR-DIGITAL;DTA124EKA,PNP,200mW,22K DVD-909 PAL ONLY TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP PAL ONLY TR-DIGITAL;DTA124EKA,PNP,200mW,22K-22KDVD-909 PAL ONLY TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23, DVD-909 PAL ONLY TR-DIGITAL;DTA124EKA,PNP,200mW,22K DVD-909 PAL ONLY TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOT- PAL ONLY TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOT- PAL ONLY TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOT- PAL ONLY TR-DIGITAL;DTA124EKA,PNP,200mW,22K-22K PAL ONLY TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP PAL ONLY TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP PAL ONLY TR-SMALL SIGNAL;KSA812,PNP,150mW,SOT-23, PAL ONLY TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOT- PAL ONLY TR-SMALL SIGNAL;KSA812,PNP,150mW,SOT-23, PAL ONLY TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP PAL ONLY TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23 DVD-909 PAL ONLY R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM PAL ONLY R-CHIP;680OHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM PAL ONLY R-CARBON;750OHM,5%,1/8W,AA,TP,1.8X3.2MM PAL ONLY R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM PAL ONLY R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM PAL ONLY R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MM PAL ONLY R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM PAL ONLY R-CARBON;750OHM,5%,1/8W,AA,TP,1.8X3.2MM PAL ONLY R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 PAL ONLY R-CARBON;560OHM,5%,1/8W,AA,TP,1.8X3 PAL ONLY R-CHIP;5.6KOHM,5%,1/10W,DA,TP,2012 DVD-909 PAL ONLY R-CARBON;560OHM,5%,1/8W,AA,TP,1.8X3 PAL ONLY R-CARBON;560OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 PAL ONLY R-CARBON;560OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 PAL ONLY R-CHIP;820OHM,5%,1/10W,DA,TP,2012 DVD-909 PAL ONLY R-CHIP;820OHM,5%,1/10W,DA,TP,2012 DVD-909 PAL ONLY R-CHIP;75OHM,5%,1/10W,DA,TP,2012 DVD-909 PAL ONLY R-CHIP;820OHM,5%,1/10W,DA,TP,2012 DVD-909 PAL ONLY
9-9
Electrical Parts List
Loc.No SCR27 SCR28 SCR32 SCR33 SCR34 SCR35 SCR36 SCR37 SCR4 SCR42 SCR43 SCR44 SCR45 SCR46 SCR5 SCR50 SCR51 SCR52 SCR53 SCR54 SCR55 SCR6 SCR66 SCR67 SCR7 SCR8 SCR9 SVJ1 VC1 VC10 VC100 VC101 VC102 VC103 VC104 VC105 VC105 VC106 VC11 VC12 VC13 VC14 VC2 VC3 VC4 VC5 VC6 VC7 VC8 VC9 VE51 VE54 VE55 VE58 VE58A VE60 VE61 VE66 VE67 VE69 VE70 VE71 VE72 VE73 VFD1 VIC50
9-10
Part No 2007-001201 2007-001166 2007-001166 2007-001166 2007-001166 2007-001166 2007-001166 2001-000969 2007-000981 2001-000969 2007-000030 2007-000468 2007-000300 2007-000300 2007-000686 2007-000774 2007-000774 2007-000774 2007-000981 2007-000981 2007-000981 2007-000686 2007-000872 2007-000872 2007-000518 2007-000981 2007-000686 3722-001375 2203-000192 2202-000849 2203-000192 2203-000192 2202-002037 2202-002037 2202-002037 2007-000029 2203-000192 2203-000192 2202-000849 2202-000849 2202-000849 2202-000849 2203-000192 2203-000192 2202-000849 2202-000849 2202-000849 2202-000849 2202-000849 2202-000849 2401-002042 2401-000369 2401-000913 2401-000369 2401-000913 2401-001353 2401-000913 2401-001353 2401-000913 2401-001353 2401-002042 2401-002042 2401-002042 2401-002042 AH07-00002A 1204-001366
Description ; Specification
Remark
R-CHIP;820OHM,5%,1/10W,DA,TP,2012 DVD-909 PAL ONLY R-CHIP;75OHM,5%,1/10W,DA,TP,2012 DVD-909 PAL ONLY R-CHIP;75OHM,5%,1/10W,DA,TP,2012 DVD-909 PAL ONLY R-CHIP;75OHM,5%,1/10W,DA,TP,2012 DVD-909 PAL ONLY R-CHIP;75OHM,5%,1/10W,DA,TP,2012 DVD-909 PAL ONLY R-CHIP;75OHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CHIP;75OHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MM PAL ONLY R-CHIP;5.6KOHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MM PAL ONLY R-CHIP;560OHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CHIP;1KOHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CHIP;10KOHM,5%,1/10W,DA,TP,2012 DVD-909 PAL ONLY R-CHIP;10KOHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CHIP;3.3KOHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CHIP;33KOHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CHIP;33KOHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CHIP;33KOHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CHIP;5.6KOHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CHIP;5.6KOHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CHIP;5.6KOHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CHIP;3.3KOHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CHIP;4.7KOHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CHIP;4.7KOHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CHIP;2.7KOHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CHIP;5.6KOHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CHIP;3.3KOHM,5%,1/10W,DA,TP,2012 PAL ONLY JACK-DIN;4P,-,NI,BLK,C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V R-CHIP;0OHM,5%,1/10W,DA,TP,2012 NTSC C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, PAL C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, PAL ONLY C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,50V,Y5V,TP, C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. C-AL;220uF,20%,10V,GP,TP,6.3x11,5 C-AL;100UF,20%,6.3V,GP,-,6.3X11,5 DVD-909 NTSC ONLY C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m DVD-909 NTSC ONLY C-AL;100UF,20%,6.3V,GP,-,6.3X11,5 DVD-909 NTSC ONLY C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m DVD-909 NTSC ONLY C-AL;470uF,20%,10V,GP,TP,8x11.5,5 C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m C-AL;470uF,20%,10V,GP,TP,8x11.5,5 C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m C-AL;470uF,20%,10V,GP,TP,8x11.5,5 C-AL;220uF,20%,10V,GP,TP,6.3x11,5 C-AL;220uF,20%,10V,GP,TP,6.3x11,5 C-AL;220uF,20%,10V,GP,TP,6.3x11,5 C-AL;220uF,20%,10V,GP,TP,6.3x11,5 VF-DISPLAY;SVV-08M,21SEG,25X100MM,DVD-90 IC-VIDEO ENCODER;SAA7128,QFP,44P,-,PLAST
Loc.No VIC51 VIC52 VL100 VL110 VL111 VL112 VL113 VL115 VL116 VL117 VL118 VL119 VR10 VR100 VR108 VR109 VR11 VR110 VR111 VR112 VR113 VR114 VR115 VR116 VR117 VR12 VR121 VR122 VR123 VR125 VR13 VR130 VR131 VR132 VR133 VR14 VR146 VR15 VR16 VR17 VR175 VR176 VR177 VR178 VR18 VR192 VR193 VR3 VR4 VR4 VR5 VR5 VR7 VR8 VR9 VSW1
Part No 1201-001419 1201-001419 3301-000353 3301-000297 3301-000297 3301-000353 2701-000138 2701-000002 2701-000002 2701-000002 2701-000002 3301-000353 2001-000008 2001-000281 2001-000969 2001-000666 2001-000008 2001-000666 2001-000666 2001-000666 2001-000666 2001-000666 2001-000666 2001-000666 2001-000969 2001-000591 2007-000572 2001-000515 2001-000290 2001-000290 2001-000591 2001-000969 2001-000780 2001-000780 2001-000780 2001-000591 2001-000969 2001-000734 2001-000734 2001-000666 2001-000969 2001-000554 2001-000780 2001-000003 2001-000666 2001-000969 2001-000969 2001-000258 2001-000221 2001-000258 2001-000221 2001-000258 2001-000977 2001-000977 2001-000008 3408-000277
Description ; Specification
Remark
IC-VIDEO AMP;7660,SSOP,16P,173MIL, DVD-909 NTSC ONLY IC-VIDEO AMP;7660,SSOP,16P,173MIL,3,6DB, CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,CORE-FERRITE BEAD;AA,3.6x1.2x5.7mm,1400, CORE-FERRITE BEAD;AA,3.6x1.2x5.7mm,1400, CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,INDUCTOR-AXIAL;18uH,5%,2.4x3.4mm INDUCTOR-AXIAL;100uH,10%,4.2x9.8mm INDUCTOR-AXIAL;100uH,10%,4.2x9.8mm INDUCTOR-AXIAL;100uH,10%,4.2x9.8mm PAL ONLY INDUCTOR-AXIAL;100uH,10%,4.2x9.8mm PAL ONLY CORE-FERRITE BEAD;AB,2.0x1.25x0.9mm,-,R-CARBON;15KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;15KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 NTSC ONLY R-CARBON;3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CHIP;220OHM,5%,1/10W,DA,TP,2012 PAL ONLY R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MM PAL ONLY R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM PAL ONLY R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM PAL ONLY R-CARBON;3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 NTSC ONLY R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM PAL ONLY R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 NTSC ONLY R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;270OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;330OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3 DVD-909 ONLY R-CARBON;1.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM PAL ONLY R-CARBON;1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM NTSC R-CARBON;1.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM PAL R-CARBON;1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM NTSC R-CARBON;1.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM PAL R-CARBON;8.2KOHM,5%,1/8W,AA,TP, DVD-909 NTSC ONLY R-CARBON;8.2KOHM,5%,1/8W,AA,TP DVD-909 NTSC ONLY R-CARBON;15KOHM,5%,1/8W,AA,TP,1.8X3.2MM SWITCH-SLIDE;50V,300mA,DP3T,-,KSA-2372 PAL ONLY
Samsung Electronics
Electrical Parts List
Loc.No
Part No
701 CON23 CON23-A HP2 HPJ01 HR1 KC1 KC2 KCE10 KCE11 KCE8 KCE9 KD1 KOP03 KR3 KR32 KR33 KR34 KR35 KR4 KSW1 KVR4
3711-001062 AH39-00030A 2001-000666 3722-000345 2001-000666 2202-002037 2202-002037 2401-001226 2401-001226 2401-002009 2401-002009 0601-001238 1201-000191 2001-000290 2001-000331 2001-000734 2001-000331 2001-000734 2001-000290 3404-000160 2101-001054
701 CON24 KD2 KSW2
702 CON22 FSW1 FSW2 FSW4 FSW5 FSW6
CONNECTOR-HEADER;BOX,6P,1R,2mm,STRAIGHT, LEAD CONNECTOR-ASSY;-,51004-04,35023-04, R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM JACK-PHONE;3P,6.4mm,AG,BLK,R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V C-AL;4.7uF,20%,16V,BP,TP,4x7,5mm C-AL;4.7uF,20%,16V,BP,TP,4x7,5mm C-AL;100uF,20%,16V,GP,TP,6.3x7,5 C-AL;100uF,20%,16V,GP,TP,6.3x7,5 LED;ROUND,RED,3.1mm,697nm IC-OP AMP;4558,DIP,8P,300MIL,DUAL,20V/mV R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;12KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;12KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM SWITCH-TACT;12V,50mA,160gf+-50gf,6.55x7. VR-ROTARY;10KOHM,20%,1/20W,SIDE
CN1 CN2 CN3 CN4 CN5 DC1 DC2 DC3 DC4 DE1 DE2 DJP1 DJP10 DJP11 DJP12 DJP13 DJP14 DJP15 DJP16 DJP17 DJP18 DJP19 DJP2 DJP20 DJP21 DJP22 DJP3 DJP4 DJP5 DJP6 DJP7 DJP8 DJP9 DL1 DLED DR1 DR2 DR3 DR4 DR5 SW1 SW2 SW3
LEAD CONNECTOR-ASSY;-,51004-04,35023-04, LED;ROUND,RED,3.1mm,697nm SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S
LEAD CONNECTOR-ASSY;-,51004-12,35023-12, SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S JOG-SHUTTLE DIAL;-,-,-,-,-,SRGPPJ-012A
ASSY-PCB-PLAY;DVD-709 AH39-00028A 3404-000165 3404-000165 3404-000165 3404-000165 3404-000165
Samsung Electronics
Loc.No
202
ASSY-PCB-PLAY;DVD-909 AH39-00029A 3404-000165 3404-000165 3404-000165 3404-000165 3404-000165 AC21-12001A
Remark
ASSY-PCB-PHONE POWER;DVD-909
ASSY-PCB-POWER;DVD-709 AH39-00033A 0601-001238 3404-000165
702 CON21 FSW1 FSW2 FSW3 FSW4 FSW7 JOG01
Description ; Specification
LEAD CONNECTOR-ASSY;-,51004-06,35023-06, SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S
Part No
Description ; Specification
Remark
ASSY-PCB-DECK;DP-3 3708-001081 3708-001001 3711-000827 3708-001108 3708-001084 2203-000208 2203-000208 2203-000208 2203-000612 2404-000259 2404-000259 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 2007-000033 3301-000325 0601-001372 2007-000800 2007-000451 2007-000451 2007-000303 2007-000303 AH34-30001A 3403-001001 3408-000323
CONNECTOR-FPC/FC/PIC;11P,1mm,STRAIGHT,SN CONNECTOR-FPC/FC/PIC;20P,1mm,SMD-A,SN CONNECTOR-HEADER:BOX,2P,1R,2mm,STRAIGHT, CONNECTOR-FPC/FC/PIC;8P,1.0MM,ANGLE,SN CONNECTOR-FPC/FC/PIC;40P,1.25mm,ANGLE,SN C-CERAMIC,CHIP;100nF,10%,50V,X7R,TP,3216 C-CERAMIC,CHIP;100nF,10%,50V,X7R,TP,3216 C-CERAMIC,CHIP;100nF,10%,50V,X7R,TP,3216 C-CERAMIC,CHIP;22nF,10%,50V,X7R,TP,3216, C-TA,CHIP;47uF,20%,6.3V,-,TP,6032,C-TA,CHIP;47uF,20%,6.3V,-,TP,6032,R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 R-CHIP;0OHM,5%,1/8W,DA,TP,3216 CORE-FERRITE BEAD;AB,3.2x2.5x1.3mm,-,LED;ROUND,GRN,3.5MM,621NM R-CHIP;360ohm,5%,1/8W,DA,TP,3216 R-CHIP;180OHM,5%,1/8W,DA,TP,3216 R-CHIP;180OHM,5%,1/8W,DA,TP,3216 R-CHIP;10KOHM,5%,1/8W,DA,TP,3216 R-CHIP;10KOHM,5%,1/8W,DA,TP,3216 SWITCH-PUSH;2EA,6.65X7.5,-,DC5V SWITCH-PUSH;5V,5mA,-,OFF-ON SWITCH-SLIDE;SSSS712GD011/12VDC 100ma
9-11
Electrical Parts List
MEMO
9-12
Samsung Electronics
10. Block Diagrams 10-1 NTSC DVD-909 DECK ASS'Y
MIC8 8M EPROM
2K EEPROM
Remote Control
MIC1 (TMP93CM41F) Main Controller
FIC1 (LC86P6232) Front Controller
Optical Coaxial
Pick-UP & I/V Amp
Disc Motor
Disc Motor Driver
Feed Motor
RIC1 (KS1461) RF Amp & DPD
Actuator & Motor Driver DIC2 4M DRAM
VIC4/10 32M SDRAM
AIC4 (AK4324) Audio DAC
LPF
AMP
S/W
LPF
AMP
C/T
AIC3 (AK4324) Audio DAC
LPF
AMP
R/L
LPF
AMP
R/R
AIC2 (AK4324) Audio DAC
LPF
AMP
F/L
LPF
AMP
F/R L1T
AIC1 (AK4324) Audio DAC
DIC1 (KS1453) DVD & CD Processor
LPF
AMP
L2T
LPF
AMP
R1T
VIC1 (ZiVA-3) A/V Decoder
R2T
SIC1 (KS1452) Digital Servo
CVBS1 AMP CVBS2 AMP VIC50 (SAA7128) Video Encoder
Samsung Electronics
Yout Cout
AMP AMP
Y
AMP
Pb
AMP
Pr
10-1
Block Diagrams
10-2 NTSC DVD-709
DECK ASS'Y
2K EEPROM
Remote Control
MIC8 8M EPROM
MIC1 (TMP93CM41F) Main Controller
FIC1 (LC86P6232) Front Controller
DIC2 4M DRAM
VIC4/10 32M SDRAM
Pick-UP & I/V Amp
Disc Motor
Disc Motor Driver
Feed Motor
RIC1 (KS1461) RF Amp & DPD
Actuator & Motor Driver
Coaxial DIC1 (KS1453) DVD & CD Processor VIC1 (ZiVA-3) A/V Decoder
AIC1 (AK4324) Audio DAC
LPF
AMP
LT
LPF
AMP
RT
AMP
CVBS
AMP
Yout Cout
SIC1 (KS1452) Digital Servo
VIC50 (SAA7128) Video Encoder
AMP
10-2
Samsung Electronics
Block Diagrams
10-3 PAL DVD-909
DECK ASS'Y
MIC8 8M EPROM
2K EEPROM
Remote Control
MIC1 (TMP93CM41F) Main Controller
FIC1 (LC86P6232) Front Controller
Optical Coaxial
Pick-UP & I/V Amp
Disc Motor
Disc Motor Driver
Feed Motor
RIC1 (KS1461) RF Amp & DPD
Actuator & Motor Driver DIC2 4M DRAM
VIC4/10 32M SDRAM
AIC4 (AK4324) Audio DAC
LPF
AMP
S/W
LPF
AMP
C/T
AIC3 (AK4324) Audio DAC
LPF
AMP
R/L
LPF
AMP
R/R
AIC2 (AK4324) Audio DAC
LPF
AMP
F/L
LPF
AMP
F/R L1T
AIC1 (AK4324) Audio DAC
DIC1 (KS1453) DVD & CD Processor
LPF
AMP
L2T
LPF
AMP
R1T
VIC1 (ZiVA-3) A/V Decoder
R2T
SIC1 (KS1452) Digital Servo
CVBS1 AMP CVBS2 AMP VIC50 (SAA7128) Video Encoder
Yout Cout
AMP AMP
Y AV1
AMP
Pb AV2
AMP
Pr RCA JACK
SCART JACK
OPTION
Samsung Electronics
10-3
Block Diagrams
10-4 PAL DVD-709
DECK ASS'Y
2K EEPROM
Remote Control
MIC8 8M EPROM
MIC1 (TMP93CM41F) Main Controller
FIC1 (LC86P6232) Front Controller
DIC2 4M DRAM
VIC4/10 32M SDRAM
Pick-UP & I/V Amp
Disc Motor
Disc Motor Driver
Feed Motor
RIC1 (KS1461) RF Amp & DPD
Actuator & Motor Driver
Coaxial DIC1 (KS1453) DVD & CD Processor VIC1 (ZiVA-3) A/V Decoder
AIC1 (AK4324) Audio DAC
SIC1 (KS1452) Digital Servo
VIC50 (SAA7128) Video Encoder
LPF
AMP
LT
LPF
AMP
RT
AMP
CVBS
AMP
Yout Cout
AMP AMP AMP
AV
AMP
10-4
Samsung Electronics
11. PCB Diagrams
11-1 Main - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
11-2
11-2 Jack - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
11-3
11-3 Phone/Power (DVD-909 Only) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
11-4
11-4 Power (DVD-709 Only) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
11-4
11-5 Play - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
11-4
11-6 Deck - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
11-4
Samsung Electronics
11-1
PCB Diagrams
11-2
SOLDER SIDE
COMPONENT SIDE
11-1 Main
Samsung Electronics
PCB Diagrams
11-2 Jack
Samsung Electronics
11-3
PCB Diagrams
11-3 Phone/Power (DVD-909 Only)
11-6 Deck
11-4 Power (DVD-709 Only)
11-5 Play
11-4
Samsung Electronics
12. Wiring Diagram
MAIN PCB JACK PCB
DVD-909
(DVD-709)
(DVD-909)
DVD-709
PHONE/POWER PCB (DVD-909 ONLY)
(DVD-909)
(DVD-709)
PLAY PCB
DECK PCB POWER PCB (DVD-709 ONLY)
Samsung Electronics
12-1
Wiring Diagram
MEMO
12-2
Samsung Electronics
13. Schematic Diagrams Block Identification of PCB
13-1 S.M.P.S. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
13-2
13-2 Main Power Supply - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
13-3
13-3 Main Micom - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
13-4
13-4 Servo - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
13-5
13-5 Video - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
13-6
13-6 Audio- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
13-7
13-7 5.1 Channel Audio (DVD-909 Only) - - - - - - - - - - - - - - - - - - - - - - - - - - - -
13-8
13-8 RF - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
13-9
13-9 ZiVA - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
13-10
13-10 DSP - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
13-11
13-11 Front Micom/VFD Display - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
13-12
13-12 Component (DVD-909 Only ; Option) - - - - - - - - - - - - - - - - - - - - - - - - - -
13-13
13-13 Scart Jack (DVD-909 PAL Only) - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
13-14
13-14 Mute - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
13-15
13-15 Play & Phone/Power (DVD-909 Only) - - - - - - - - - - - - - - - - - - - - - - - - - -
13-16
13-16 Play & Power (DVD-709 Only) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
13-16
13-17 Deck - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
13-17
13-18 Remote Control - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
13-18
Main PCB (Component Side)
Jack PCB (Conductor Side) Samsung Electronics
13-1
Schematic Diagrams
13-1 S.M.P.S.
13-2
Samsung Electronics
Schematic Diagrams
13-2 Main Power Supply
Samsung Electronics
13-3
Schematic Diagrams
13-3 Main Micom
13-4
Samsung Electronics
Schematic Diagrams
13-4 Servo
Samsung Electronics
13-5
Schematic Diagrams
13-5 Video
(DVD-909 OPTION)
(DVD-909 OPTION)
Y Output
13-6
C Output
CVBS Output
Samsung Electronics
Schematic Diagrams
13-6 Audio
(DVD-909 OPTION)
Samsung Electronics
13-7
Schematic Diagrams
13-7 5.1 Channel Audio (DVD-909 Only)
13-8
Samsung Electronics
Schematic Diagrams
13-8 RF
Samsung Electronics
13-9
Schematic Diagrams
13-9 ZiVA
13-10
Samsung Electronics
Schematic Diagrams
13-10 DSP
Samsung Electronics
13-11
Schematic Diagrams
13-11 Front Micom/VFD Display
U.S.A.
FRANCE
CON23-A (DVD-909) CON24 (DVD-709)
TO KEY CN18
CN15 (DVD-909 ; PIN12)
CN16 (DVD-709 ; PIN6) TO KEY CON22 (PIN6) TO KEY CON21 (PIN12)
13-12
Samsung Electronics
Schematic Diagrams
13-12 Component (DVD-909 Only ; Option)
Samsung Electronics
13-13
Schematic Diagrams
13-13 Scart Jack (DVD-909 PAL Only)
R Output (Scart Jack)
13-14
G Output (Scart Jack)
B Output (Scart Jack)
Samsung Electronics
Schematic Diagrams
13-14 Mute
Samsung Electronics
13-15
Schematic Diagrams
13-15 Play & Phone/Power (DVD-909 Only)
PLAY
PHONE/POWER
13-16 Play & Power (DVD-709 Only)
PLAY
13-16
POWER
Samsung Electronics
Schematic Diagrams
13-17 Deck
Samsung Electronics
13-17
Schematic Diagrams
13-18 Remote Control
13-18
Samsung Electronics
