Transcript
MARKETIER 18 GAUGE COUNTER SECTIONS
JOB NAME: ___________________________ ITEM NO.: ____________________________ NO. REQUIRED: _______________________
DESCRIPTION: Shall be Market Forge Marketier Counter Section Type Number ____________. SOLID - Stainless Steel Flat Surface □ Model MSFC
Shelves shall be ____ tier high (3 to 8) or as shown. Upper Shelves
Lower Shelves
LENGTHS:
LENGTHS: 30” (762mm) 36” (914mm)
42” (1097mm)
42” (1097mm)
48” (1219mm)
48” (1219mm)
54” (1372mm)
54” (1372mm)
60” (1524mm)
60” (1524mm)
WIDTHS:
WIDTHS:
14” (356mm)
20” (508mm)
18” (457mm)
24” (610mm)
NOTE: The Following sizes shall be constructed with a reinforcing bar in the length dimensions for extra security against sagging under exceptionally heavy loads: □ 18” x 60” □ 20” x 60” □ 24” x 54” □ 24” x 60”
Available in the following: □ Stainless steel Available in the following lengths: □ 78” (1981mm) - Rear Posts □ 42” (1067mm) - Front Upper Posts □ 36” (914mm) - Front Lower Posts NOTE: Special length post are available upon request. In multiple standard sections, one section only shall require six posts and all adjacent sections three posts with two supporting clamps per shelf. Shelves shall be delivered knocked down and packed in protective cardboard containers marked with the size and material of the contents. OPTIONAL AT EXTRA COST: □ Double Fold & Flatten Reinforcement provide security against sagging under exceptionally heavy loads. □ Adjustable flanged feet □ Adjustable wall brackets for fastening rear posts to wall. □ Dividers (Front-to-Back) □ Back Ledges □ End Ledges □ Label Holders □ Shelf Clips □ Louvered or Embossed shelves above and below counter section.
FOOD SERVICE EQUIPMENT Marketier Counter Sections
30” (762mm) 36” (914mm)
POSTS: Shall be provided with press fit plastic caps at both top and swivel casters for the base. Posts shall be marked at 2” intervals to assist alignment of shelves during assembly.
SPEC SHEET: R-1534J 03/11
SHELVES: Shall consist of two upper shelves, three lower shelves, and two complete sets of rear, counter top, and front posts (or any desired variation). Each shelf shall be made of 18 gauge material with all four corners uniformly coped to exact contour to receive internal corner castings in crevicefree alignment. The perimeter of each shelf shall have a die-formed raised marine edge, (3mm) high on a (7mm) radius. The lower edge of the shelf perimeter shall be hemmed and pressed tight along the shelf length. Shelves shall be shipped with set screws for each corner to allow shelves to be installed or adjusted at any desired spacing. Shelf corner castings have a hole to take 1” O.D. shelf posts. Shelves shall be available as required in any combination of the following widths and lengths as designed or as shown on plans. .
The manufacturer reserves the right to modify materials and specifications without notice.
PRINTED IN U. S. A. 35 Garvey Street • Everett • MA • 02149 Tel: (617) 387-47100 • Toll Free: (866) 698-3188 • Fax: (617) 387-4456 • Outside MA Fax: (800) 227-2659 E-Mail:
[email protected] • Website: w w w . m f i i . c o m
MARKETIER 18 GAUGE COUNTER SECTIONS
DETAILS & DIMENSION
AVAILABLE TYPES OF SHELVING
SOLID LOUVERED (OPTIONAL)
EMBOSSED
MATERIAL
MODEL TYPE
Solid (Flat Surface)
Stainless Steel
MSFC
Louvered or Embossed Shelves above and below counter are available as options at an additional cost.
Marketier Counter Sections
FOOD SERVICE EQUIPMENT
SPEC SHEET: R-1534J 03/11
(OPTIONAL)
TYPES
This Product is ETL Complaint with ANSI/NSF-2 Standard.
35 Garvey Street • Everett • MA • 02149 Tel: (617) 387-47100 • Toll Free: (866) 698-3188 • Fax: (617) 387-4456 • Outside MA Fax: (800) 227-2659 E-Mail:
[email protected] • Website: w w w . m f i i . c o m
