Transcript
s
Issued by Siemens Home and Office Communication Devices GmbH & Co. KG Schlavenhorst 66 D-46395 Bocholt © Siemens Home and Office Communication Devices GmbH & Co. KG 2007 All rights reserved. Subject to availability. Rights of modification reserved. www.siemens.com/gigaset
BA SL370.indd 2-3
Gigaset SL370
Gigaset 28.02.2007 14:28:18 Uhr
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / overview.fm / 9.7.07
Handset at a glance
Handset at a glance
18 17 16
Ð
½ò
V
1 2
INT 1 15.11.07 ?
09:45 SMS
3 15 14
4
13
5
12
11
6
10
7
9 8
Version 4, 16.09.2005
Base station at a glance
1 Display (screen) in idle status 2 Charge status of the battery pack = e V U (flat to full) = flashes: battery pack almost flat e V U flashes: battery pack charging 3 Display keys (page 10) 4 Message key Access to calls and message lists; Flashes: new message or new call 5 End call key, On/Off key End call, cancel function, go back one menu level (press briefly), back to idle status (press and hold), activate/deactivate handset (press and hold in idle status) 6 Hash key Keypad lock on/off (press and hold in idle status), Toggle between upper/lower case and digits (press and hold) 7 Call-by-call list key Open call-by-call list 8 Connection socket for headset and PC interface 9 Microphone 10 Recall key - Confer (flash) - Insert a dialling pause (press and hold) 11 Star key Ringer tones on/off (press and hold), With an open connection: switch between dial pulsing/touch tone dialling (press briefly), Open special characters table 12 Key 1 Select network mailbox (press and hold) 13 Talk key Answer a call, open last number redial list (press briefly), start dialling (press and hold) When writing an SMS: send SMS 14 Handsfree key Switch between earpiece and handsfree mode; Lights up: handsfree activated; Flashes: incoming call 15 Control key (page 10) 16 Bluetooth activated (page 48) 17 Eco mode activated (page 12) 18 Signal strength Ð i Ñ Ò (high to low) | flashes: no reception
Registration/paging key (page 36) 1
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / SL370IVZ.fm / 9.7.07
Contents
Contents
Making cost-effective calls . . . . 25
Base station at a glance . . . . . . . . 1
Linking call-by-call numbers with one number . . . . . . . . . . . . . . . . 25 Automatic network provider preselection (Preselection) . . . . . . . . . 25
Safety precautions . . . . . . . . . . . . 4
SMS (text messages) . . . . . . . . . 27
Gigaset SL370 – More than just a telephone . . . . . 6
Writing/sending an SMS . . . . . . . . . . . Receiving an SMS . . . . . . . . . . . . . . . . Notification by SMS . . . . . . . . . . . . . . . SMS mailboxes . . . . . . . . . . . . . . . . . . Setting SMS centres . . . . . . . . . . . . . . SMS info services . . . . . . . . . . . . . . . . SMS on a PABX . . . . . . . . . . . . . . . . . . Activating/deactivating the SMS function . . . . . . . . . . . . . . . . . . . . SMS troubleshooting . . . . . . . . . . . . .
Handset at a glance . . . . . . . . . . . 1
First steps . . . . . . . . . . . . . . . . . . . . 6 Pack contents . . . . . . . . . . . . . . . . . . . . 6 Installing the base station and charging cradle . . . . . . . . . . . . . . . . . . . 6 Setting up the handset for use . . . . . . . 7
Operating the handset . . . . . . . . 10 Control key . . . . . . . . . . . . . . . . . . . . . Display keys . . . . . . . . . . . . . . . . . . . . Reverting to idle status . . . . . . . . . . . . Menu guidance . . . . . . . . . . . . . . . . . Correcting incorrect entries . . . . . . . .
10 10 11 11 11
33 34
Using the network mailbox . . . 35
ECO DECT . . . . . . . . . . . . . . . . . . . 12
Configuring fast access for the network mailbox . . . . . . . . . . . . . . 35 Viewing the network mailbox report . . . . . . . . . . . . . . . . . . . . . . . . . 35
Menu tree . . . . . . . . . . . . . . . . . . 13
Using several handsets . . . . . . . 36
Making calls . . . . . . . . . . . . . . . . . 16 Making an external call . . . . . . . . . . . Ending a call . . . . . . . . . . . . . . . . . . . . Accepting a call . . . . . . . . . . . . . . . . . Calling Line Identification . . . . . . . . . Handsfree talking . . . . . . . . . . . . . . . . Muting . . . . . . . . . . . . . . . . . . . . . . . .
16 16 16 16 17 17
Making calls using network services . . . . . . . . . . . . . 18 Setting functions for all subsequent calls . . . . . . . . . . . . . . . . . 18 Functions during a call . . . . . . . . . . . . 18 Function after a call . . . . . . . . . . . . . . 19
Using the directory and lists . . . 20 Directory/call-by-call list . . . . . . . . . . . 20 Last number redial list . . . . . . . . . . . . 23 Opening lists with the message key . 24
Version 4, 16.09.2005
27 29 31 31 32 33 33
2
Registering handsets . . . . . . . . . . . . . . De-registering handsets . . . . . . . . . . . Locating a handset ("paging") . . . . . . Changing the base station . . . . . . . . . Making internal calls . . . . . . . . . . . . . . Listening in to an external call . . . . . . Changing the name of a handset . . . . Changing a handset's internal number . . . . . . . . . . . . . . . . . . . . . . . . Using a handset as a room monitor . . . . . . . . . . . . . . . . . . . Walky-talky mode . . . . . . . . . . . . . . . .
36 36 36 37 37 38 38 38 39 40
Handset settings . . . . . . . . . . . . 41 Shortcuts for functions and numbers . . . . . . . . . . . . . . . . . . . . . . . Changing the display language . . . . . Setting the display . . . . . . . . . . . . . . . Setting the screensaver . . . . . . . . . . . . Setting the display backlight . . . . . . . .
41 42 42 42 43
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / SL370IVZ.fm / 9.7.07
Contents Activating/deactivating auto answer . . . . . . . . . . . . . . . . . . . . Changing the handsfree/ earpiece volume . . . . . . . . . . . . . . . . . Changing ringer tones . . . . . . . . . . . . My stuff . . . . . . . . . . . . . . . . . . . . . . . Activating/deactivating advisory tones . . . . . . . . . . . . . . . . . . Setting the alarm clock . . . . . . . . . . . . Setting an appointment (calendar) . . Displaying missed appointments and anniversaries . . . . . . . . . . . . . . . . . . . Using Bluetooth devices . . . . . . . . . . . Setting your own area code . . . . . . . . Restoring the handset to factory settings . . . . . . . . . . . . . . . . . .
43 43 43 45 46 46 47 48 48 50 50
Base station settings . . . . . . . . . . 51 Protecting against unauthorised access . . . . . . . . . . . . . . . . . . . . . . . . . Activating/deactivating music on hold . . . . . . . . . . . . . . . . . . . Repeater support . . . . . . . . . . . . . . . . Restoring the base station to the factory settings . . . . . . . . . . . . . .
51
Appendix . . . . . . . . . . . . . . . . . . 54 Care . . . . . . . . . . . . . . . . . . . . . . . . . . . Contact with liquid . . . . . . . . . . . . . . . Questions and answers . . . . . . . . . . . . Service (Customer Care) . . . . . . . . . . . Authorisation . . . . . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . . . . . .
54 54 54 56 57 57
Notes on the user guide . . . . . . 58 Example of a menu input . . . . . . . . . . 58 Example of multiple line input . . . . . . 58 Writing and editing text . . . . . . . . . . . 59
Additional functions via the PC interface . . . . . . . . . . . . . . . . 60 Accessories . . . . . . . . . . . . . . . . . 61 Wall-mounting the base station . . . . . . . . . . . . . . . . 63 Index . . . . . . . . . . . . . . . . . . . . . . 64
51 51 51
Connecting the base station to the PABX . . . . . . . . . . . . . . . . . 52
Version 4, 16.09.2005
Dialling modes and recall . . . . . . . . . . Saving an access code (outside line code) . . . . . . . . . . . . . . . Setting pauses . . . . . . . . . . . . . . . . . . Switching temporarily to tone dialling (DTMF) . . . . . . . . . . . . . .
52 52 52 53
3
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / security.fm / 9.7.07
Safety precautions
Safety precautions Warning:
Read the safety precautions and the user guide before use. Explain their contents and the potential hazards associated with using the telephone to your children.
$
Only use the mains adapter supplied, as indicated on the underside of the base station or charging cradle. Fit only the approved rechargeable battery pack (page 57)! That means never use a conventional (non-rechargeable) battery pack, as this could result in significant health risks and personal injury. Battery packs should not be disposed of in general household waste. Observe the local waste disposal regulations, which you can find out about by contacting your local authority or the dealer you purchased the product from. The operation of medical appliances may be affected. Be aware of the technical conditions in your particular environment, e.g. doctor's surgery. Do not hold the rear of the handset to your ear when it is ringing or when the handsfree function is activated. Otherwise you risk serious and permanent damage to your hearing. The handset may cause an unpleasant humming noise in hearing aids. Do not install the base station or charging cradle in bathrooms or shower rooms. The base station and charging cradle are not splashproof (page 54). Do not use your phone in environments with a potential explosion hazard, e.g. paint shops.
ƒ
If you give your Gigaset to someone else, make sure you also give them the user guide.
Version 4, 16.09.2005
Please remove faulty base stations from use or have them repaired by Siemens Service, as they could interfere with other wireless services.
4
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / security.fm / 9.7.07
Safety precautions All electrical and electronic equipment must be disposed of separately from general household waste using the sites designated by local authorities. If a product displays this symbol of a crossed-out rubbish bin, the product is subject to European Directive 2002/96/EC. The appropriate disposal and separate collection of used equipment serve to prevent potential harm to the environment and to health. They are a precondition for the re-use and recycling of used electrical and electronic equipment. For further information on disposing of your used equipment, please contact your local authority, your refuse collection service or the dealer you purchased the product from.
Please note:
Version 4, 16.09.2005
Not all of the functions described in this manual are available in all countries.
5
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / starting.fm / 9.7.07
Gigaset SL370 – More than just a telephone
Gigaset SL370 – More than just a telephone
Version 4, 16.09.2005
Your phone, which has a clearly laid out colour display (65K colours) doesn't just offer you the option of sending and receiving SMS messages via the fixed network and of saving up to 250 phone numbers and e-mail addresses (page 20) – it can do much more than that: u You can reduce the transmission power by activating the eco mode (page 12). u You can programme the keys of your phone with important numbers or frequently used functions. The number is then dialled or the function started by simply pressing a key (page 41). u You can easily make calls using network services (page 18). u You can designate important people as VIPs so you can tell important calls from the ringer tone (page 21). u You can assign pictures to your contacts. You can then tell who is calling you from the picture on your handset's display. Precondition: Calling Line Identification (CLIP, page 16). u You can store appointments (page 47) and anniversaries (page 23) in your phone and it will remind you of them in advance. u You can use Bluetooth™ for wireless communication with other devices (e.g. headsets) that also use this technology (see page 48). Enjoy using your new telephone!
6
First steps Pack contents u one Gigaset SL370 base station with
mains adapter,
u one Gigaset SL37H handset, u one charging cradle with mains u u u u u
adapter, one phone cord, one battery pack, one battery cover, one belt clip, one user guide.
Installing the base station and charging cradle The base station and charging cradle are designed for use in enclosed dry rooms with a temperature range of +5 °C to +45 °C. Set up the base station at a central point in the apartment or house. You can find instructions on how to mount the base station on the wall at the end of this user guide.
Please note: u Never expose the telephone to heat
sources, direct sunlight or other electrical appliances. u Protect your Gigaset from moisture, dust, corrosive liquids and vapours.
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / starting.fm / 9.7.07
First steps
Range and reception strength
u If you buy a replacement phone cord,
make sure that the phone jack has the correct type of wiring.
Range: u Outdoors: up to 300 m u Indoors: up to 50 m
Correct phone jack assignment 3 2 1
The range is reduced when eco mode is on (see page 12).
4 5 6
Reception strength: The display shows the quality of the radio contact between the base station and handset: u Good to poor: Ð i Ñ Ò u No reception: | flashes
the phone jack as shown below and place the cable in the cable channels.
unused unused a b unused unused
Setting up the handset for use The display is protected by a plastic film. Please remove the protective film!
Connecting the base station
¤ First connect the mains unit and then
1 2 3 4 5 6
Fitting the battery pack Warning:
1
2
3
1
1 Underside of the base station (detailed view) 2 Mains adapter 230 V 3 Phone jack with phone cord
Only use the rechargeable Siemens original battery pack (page 57)! Never use a conventional (non-rechargeable) battery or other battery types as this could result in significant health risks and personal injury. For example, the batteries could explode. The phone could also malfunction or be damaged as a result of using batteries that are not of the recommended type.
¤ With the pins to the front, insert the ¤
battery pack into the cavity at an angle from the left. Then press it into the housing from above until the bracket on the side of the battery back snaps securely into the housing.
Please note:
Version 4, 16.09.2005
u The mains adapter must always be
connected, as the phone will not operate without mains connection. u Only use the mains adapter and phone cord supplied.
7
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / starting.fm / 9.7.07
First steps Please note: To remove the battery pack, you must first press the bracket on the side.
a
b
Closing the battery cover
¤ Align the battery cover parallel to the casing and press down until it clicks into place.
¤ Lift the cover. Placing the handset in the charging cradle
¤ Plug the charging cradle mains adapter into a mains power socket.
¤ Place the handset in the charging craAttaching the belt clip There are notches for attaching the belt clip on the side of the handset at the same height as the display. ¤ Press the belt clip onto the back of the handset so that the protrusions on the belt clip engage with the notches.
dle with the display facing forward. The handset is already registered with the base station at the factory. INT 1 appears in the display. You do not have to re-register. If, nonetheless, you have to register your handset with the base station, see page 36.
Please note:
You can change the name of the handset (page 38).
To charge the battery pack, leave the handset in the charging cradle.
Please note:
Opening the battery cover
¤ If fitted, remove the belt clip. ¤ Lift the device with the keypad facing the palm of your hand.
¤ Place the thumb of your other hand on
Version 4, 16.09.2005
the loudspeaker (a) and use the index finger of the same hand to press the groove at the top of the handset (b).
8
– If the handset has switched itself off because the battery pack is flat and is then placed in the charging cradle, it will switch itself on automatically. – Only place the handset in the charging cradle that is intended for it.
For questions and problems see page 54.
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / starting.fm / 9.7.07
First steps
Initial charging and discharging of the battery pack If the handset is activated, the flashing battery icon e in the top right of the display indicates that the battery pack is being charged. During handset operation, the battery icon indicates the charge status of the battery pack (page 1). The correct charge status can only be displayed if the battery pack is first fully charged and discharged. ¤ To do this, leave the handset in the charging cradle continuously for ten hours. Your handset need not be switched on for it to charge. ¤ Afterwards, remove the handset from the charging cradle and do not put it back again until the battery pack is fully discharged.
Please note:
After the first battery charge and discharge, you may place your handset in the charging cradle after every call.
Please note: u Always repeat the charging and dis-
charging procedure if you remove the battery pack from the handset and insert it again. u The battery pack may warm up as it is charging. This is not dangerous. u After a time the charge capacity of the battery pack will decrease for technical reasons.
Setting the date and time Set the date and time so that the correct date and time can be assigned to incoming calls, and so that the alarm and the calendar can be used. ¤ If you have not yet set the date and time, press the display key §Time§ to open the input field. To change the time, open the input field with: w ¢ Ð ¢ Date/Time ¤ Change multiple line input: Date: Enter the day, month and year in 8-digit format. Time: Enter hours and minutes as 4 digits (e.g. Q M 5 for 07:15 a.m. §Save§ Press the display key
Display in idle status Once the phone is registered and the time set, the idle display looks as shown here (example): Ð
V INT 1
15.11.07 ?
07:15 SMS
Version 4, 16.09.2005
Your phone is now ready for use. If you have any queries about using your phone, please read the tips on troubleshooting ("Questions and Answers", page 54) or contact our customer service department (Customer Care, page 56).
9
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / starting.fm / 9.7.07
Operating the handset
Operating the handset Activating/deactivating the handset a
In idle status, press and hold the end call key (confirmation tone).
Activating/deactivating the keypad lock # Press and hold the hash key. You will hear the confirmation tone. The Ø icon appears in the display when the keypad lock is activated. The keypad lock is deactivated automatically if someone calls you. It is reactivated when the call is finished.
Control key
In the main menu, submenus and lists t / s Scroll up/down line by line. w Open menu or confirm selection. u Go back one menu level or cancel.
In input fields You can use the control key to move the cursor up t, down s, right v or left u.
During an external call s u
Open the directory. Initiate internal consultation call and mute. Change the earpiece volume or handsfree volume.
t
Display keys The function of the display keys changes depending on the particular operating situation. Example:
Below, the side of the control key that you must press in the respective operating situation is marked in black (top, bottom, right, left, centre), e.g. v for "press right on the control key" or w for "press the centre of the control key". The control key has a number of different functions:
When the handset is in idle status
Version 4, 16.09.2005
s w/v u t
10
Open the directory. Open the main menu. Open list of handsets. Call up the menu for setting the handset's call volume (page 43), ringer tones (page 43), advisory tones (page 46) and silent alert (page 44).
?
SMS
1 2
1 Current display key functions are shown in the bottom display line. 2 Display keys
The most important display icons are: } Left display key, as long as it has not been assigned a function (page 41). ¨ Open the main menu. §Options§ Open a context-dependent menu. W Delete key: deletes one character at a time from right to left. Î Go back one menu level or cancel operation.
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / starting.fm / 9.7.07
Operating the handset Œ Ó •
Fetch e-mail address from the directory. Copy number into directory. Open the last number redial list.
Reverting to idle status You can revert to idle status from anywhere in the menu as follows: ¤ Press and hold the end call key a. Or: ¤ Do not press any key: after 2 minutes the display will automatically revert to idle status. Changes that you have not confirmed or saved by pressing §OK§, §Yes§, §Save§, §Send§ or Save Entry §OK§ will be lost. An example of the display in idle status is shown on page 1.
Menu guidance Your telephone's functions are accessed using a menu that has a number of levels.
Main menu (first menu level)
¤ When the handset is in idle status,
press w to open the main menu. The main menu functions are shown in the display as a list with colour icons and names. To access a function, i.e. to open the corresponding submenu (next menu level): ¤ Navigate to the function using the control key q. Press the display key §OK§.
Version 4, 16.09.2005
Submenus The functions in the submenus are displayed as lists. To access a function: ¤ Scroll to the function with the control key q and press §OK§. Or:
¤ Enter the corresponding digit combina-
tion (page 13). Briefly press the end call key a once to return to the previous menu level / cancel the operation.
Illustration in the user guide The operating steps are shown in abbreviated form.
Example The illustration: w ¢ Ð ¢ Date/Time means: w Press the key to display the main menu. Ð Use the control key q to scroll through submenu Settings and press §OK§. Date/Time Scroll to the function with the control key q and press §OK§.
Other types of illustrations: c / Q / * etc. Press the matching key on the handset. ~ Enter digits or letters.
You will find detailed examples of menu entries and multiple line input in the appendix to this user guide, page 58.
Correcting incorrect entries You can correct incorrect characters in the text by navigating to the incorrect entry using the control key. You can then: u press X to delete the character to the left of the cursor u insert characters to the left of the cursor u overwrite the character (flashing) when entering the time and date etc.
11
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / starting.fm / 9.7.07
ECO DECT
ECO DECT ECO DECT reduces power consumption by using a power supply with low power consumption and also reduces the transmission power of the base station. You can set this manually with your handset. It can be used by several handsets at the same time. Your handset also reduces the transmission power depending on the distance to the base station.
Activating/deactivating eco mode:
v ¢ Ð ¢ Base ¢ Add. Features ¢ Eco Mode §OK§ Press the display key ( ‰ = activated). When eco mode is activated, the ½ icon is displayed at the top of the screen.
Please note:
Version 4, 16.09.2005
– Activating eco mode reduces the range of the base station. – Eco mode and any repeater support (see page 51) cancel each other out, i.e. both functions cannot be used at the same time. – If external handsets (GAP) and handsets from earlier Gigaset versions are used, your handset will not automatically reduce the transmission power to the base station.
12
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / menuetree.fm / 9.7.07
Menu tree
Menu tree Instead of scrolling to locate a menu function, you can select a function more quickly by opening the menu and keying in a digit combination (or shortcut). Example: w N 2 2 for "Set ringer tone for external calls". With the telephone in idle status, press w (open main menu): 1
SMS î
You have activated an SMS mailbox (general or private) without a PIN 1-1
New SMS
(page 27)
1-2
Incoming 0
(page 30)
1-3
Outgoing 0
(page 28)
You have activated an SMS mailbox with a PIN or 2-3 mailboxes 1-1
Version 4, 16.09.2005
1-2 to 1-4
Mailbox
Mailbox 1 Mailbox 2 Mailbox 3
1-1-1
New SMS
(page 27)
1-1-2
Incoming 0
(page 30)
1-1-3
Outgoing 0
(page 28)
1-2-1 to 1-4-1
New SMS
(page 27)
1-2-2 to 1-4-2
Incoming 0
(page 30)
1-2-3 to 1-4-3
Outgoing 0
(page 28)
1-5
SMS Service
(page 33)
1-6
Settings
1-6-1
Service Centres
(page 32)
1-6-2
SMS Mailboxes
(page 31)
1-6-3
Notify Number
(page 31)
1-6-4
Notify Type
(page 31)
1-6-5
Status Report
(page 28)
2
Sel. Services ê
2-6
All Calls
2-6-1
Call Divert
(page 18)
2-6-2
Parallel Ringing
(page 18)
2-7
Ringback Off
(page 19)
3
Calls List Ì
(page 24)
13
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / menuetree.fm / 9.7.07
Menu tree 4
Add. Features í
4-3
Room Monitor
(page 39)
4-4
Walky-Talky
(page 40)
4-5
Data Transfer
Bluetooth
(page 48)
Directory
(page 22)
4-7
Missed Alarms
(page 48)
5
Alarm Clock ì
(page 46)
6
Calendar ç
(page 47)
7
Resource Dir. Ï
7-1
Screensavers
(page 45)
7-2
Caller Pictures
(page 45)
7-3
Sounds
(page 45)
7-4
Capacity
(page 45)
8
Settings Ð
8-1
Date/Time
(page 9)
8-2
Audio Settings
8-2-1
Handset Volume
(page 43)
8-2-2
Ringer Settings
(page 44)
8-2-3
Advisory Tones
(page 46)
8-2-4
Silent Alert
(page 44)
8-3-1
Screen Saver
(page 42)
8-3-2
Colour Scheme
(page 42)
8-3-3
Contrast
(page 42)
8-3-4
Backlight
(page 43)
8-4-1
Language
(page 42)
8-4-2
Auto Answer
(page 43)
8-4-3
Register H/Set
(page 36)
8-4-4
Select Base
(page 37)
8-4-5
Area Codes
(page 50)
8-4-6
Reset Handset
(page 50)
8-3
8-4
Version 4, 16.09.2005
4-5-2 4-5-3
14
Display
Handset
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / menuetree.fm / 9.7.07
Menu tree 8-5
Version 4, 16.09.2005
8-6
Base
Voice Mail
8-5-2
Music on hold
(page 51)
8-5-3
System PIN
(page 51)
8-5-4
Base Reset
(page 51)
8-5-5
Add. Features
(page 12, page 38, page 52)
8-5-6
Preselection
(page 26)
8-5-7
Calls List Type
(page 25)
8-6-1
Set Key 1
(page 35)
15
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / telefony.fm / 9.7.07
Making calls
Making calls
External calls are calls using the public telephone network. ~ c Enter the number and press the talk key. Or: c ~ Press and hold the talk key c and then enter the number. You can cancel the dialling operation with the end call key a. You are shown the duration of the call while the call is in progress.
The handset indicates an incoming call in three ways: by ringing, by a display on the screen and by the flashing handsfree key d. You can accept the call by: ¤ Pressing the talk key c. ¤ Pressing the handsfree key d. ¤ Press the display key §Accept§. If the handset is in the charging cradle and the Auto Answer function is activated (page 43), the handset will take a call automatically when you lift it out of the cradle. If the ringer tone is intrusive, press the §Silence§ display key. You can take the call as long as it is displayed on the screen.
Please note:
Answering a call on a Bluetooth headset
Continuing a call on a Bluetooth headset
Precondition: Bluetooth is activated; a connection has been established between the Bluetooth headset and the handset (see page 48). Only press the talk key on the headset when the headset rings; it can take up to 5 seconds to establish a connection with the handset. For further details on your headset, see the user guide issued with it.
Making an external call
Dialling using the directory, the call-by-call list (page 1, page 20) or the calls and last number redial list (page 24/page 23) saves you from having to re-enter numbers and network provider prefixes ("call-by-call numbers").
Precondition: Bluetooth is activated; a connection has been established between Bluetooth headset and the handset (see page 48). Press the talk key on the Bluetooth headset; it may take up to 5 seconds to establish a connection to the handset. For further details on your headset, see the user guide issued with it.
Ending a call a
Version 4, 16.09.2005
Accepting a call
16
Press the end call key.
Calling Line Identification When you receive a call, the caller's number is displayed on the screen if the following conditions are met: u Your network provider supports CLIP, CLI. – CLI (Calling Line Identification): the caller's number is transmitted. – CLIP (Calling Line Identification Presentation): the caller's number is displayed. u You have arranged CLIP with your network provider.
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / telefony.fm / 9.7.07
Making calls u The caller has arranged CLI with the
network provider.
Call display with CLIP/CLI If the number of the caller is saved in your directory, you will see their name, and if you have assigned a CLIP picture to that caller, this will also be displayed.
Å
1234567890 Accept
1 2
Silence
1 Ringer tone icon 2 Number or name of caller
The following is displayed in place of the number: u External, if no number is transmitted. u Withheld, if the caller has withheld Calling Line Identification. u Unavailable, if the caller has not arranged Calling Line Identification.
Switching between earpiece and handsfree mode d Press the handsfree key. During a call, switch handsfree on or off. If you wish to place the handset in the charging cradle during a call: ¤ Press and hold the handsfree key d while placing the handset in the base station. If the handsfree key d does not light up, press the key again. For how to adjust the handsfree volume see page 43.
Muting You can deactivate the microphone in your handset during an external call. The other party hears hold music. u Press the control key on the left to mute the handset. ” Press the display key to reactivate the microphone. You can switch the hold music on and off (page 51).
Handsfree talking In handsfree mode, instead of holding the handset to your ear you can put it down, for example on the table in front of you, to allow others to participate in the call.
Activating/deactivating handsfree mode Activating while dialling ~d
Version 4, 16.09.2005
¤
Enter the number and press the handsfree key. You should inform your caller before you use the handsfree function so that they know someone else is listening.
17
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / TNet_Features_SAG.fm / 9.7.07
Making calls using network services
Making calls using network services Network services are functions that your network provider makes available to you. You have to request these services from your network provider. ¤ If you require assistance, please contact your network provider.
Setting functions for all subsequent calls If you have completed one of the following procedures, a code is sent. ¤ After confirmation from the telephone network, press the end call key a. You can set the following features:
General call diversion
w ¢ ê ¢ All Calls ¢ Call Divert ¤ Change multiple line input: When: All Calls / No Answer / When Busy. Call No.: Press the display key §Edit§. Enter number to which call is to be diverted or: Press s. Select number from the directory and press §OK§. Press Save to save. Status: Activate/deactivate call diversion. ¤ Press the display key §Send§. a After the announcement, press the end call key.
Version 4, 16.09.2005
Activating/deactivating call waiting
w ¢ ê ¢ All Calls ¢ Call Waiting Status: Activate/deactivate. §Send§ Press the display key.
18
Functions during a call Initiating ringback You hear the busy tone. §Options§ ¢ Ringback a Press the end call key.
Consultation During a call: §Ext.Call§ Press the display key. ~ Enter the number. You have the following options: u Toggling: ¤ Use q to toggle between the participants. End the call with one participant: ¤ Use q to switch to the participant. Then: §Options§ End Active Call. u Conference call: ¤ Press the display key §Conf.§. End the conference call (toggle): ¤ Press §EndConf§. u End call with both participants: ¤ Press the end call key a.
Accepting call waiting Press the display key. You have the option of toggling or holding a conference call. §Accept§
Please note:
Without CLIP a waiting call is only announced with a beep.
Accepting a waiting call §Options§
¢ Accept waiting call
Rejecting a waiting call §Options§
¢ Reject waiting call
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / TNet_Features_SAG.fm / 9.7.07
Making calls using network services
Function after a call Cancelling ringback
Version 4, 16.09.2005
w ¢ ê ¢ Ringback Off
19
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / direct_charges.fm / 9.7.07
Using the directory and lists
Using the directory and lists The options are: u Directory u Call-by-call list u Last number redial list u SMS list u Call history You can store a total of 250 entries in the directory and call-by-call list. You create the directory and call-by-call list for your own individual handset. You can also send lists/entries to other handsets (page 22).
Directory/call-by-call list Please note:
For quick access to a number from the directory or the call-by-call list (quick dial), you can assign the number to a key.
Directory In the directory you can store u Up to three numbers and associated first names and surnames u VIP designation and VIP ringer tone (optional) u E-mail address (optional) u CLIP pictures (optional) u Anniversaries with reminder. ¤ With the handset in idle status, open the directory by pressing the s key.
Length of the entries (directory)
Version 4, 16.09.2005
3 numbers: each max. 32 digits First name and surname: each max. 16 characters E-mail address: max. 60 characters
20
Call-by-call list The call-by-call list is used to store the access codes for network providers (so-called "Call-by-call numbers"). ¤ Open the call-by-call list in idle status by pressing the C key.
Length of entries Number: Name:
max. 32 digits max. 16 characters
Storing a number in the directory
s ¢ New Entry ¤ Change multiple line input: First Name / Surname: Enter a name in at least one of the fields. Phone (Home) / Phone (Office) / Phone (Mobile) Enter a number in at least one of the fields. E-mail Enter e-mail address. Annivers.: Select On or Off. With setting On: enter Anniversary (Date) and Annivers. (Time) (page 23) and select reminder type: Annivers. (Signal). Caller Picture If required, select a picture to be displayed when the caller calls (page 45). Precondition: Calling Line Identification (CLIP). ¤ Save changes: (page 59).
Storing a number in the call-by-call list
C ¢ New Entry ¤ Change multiple line input: Name: Enter name. Number: Enter number.
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / direct_charges.fm / 9.7.07
Using the directory and lists
Order of directory/call-by-call list entries Directory entries are generally sorted alphabetically by surname. Spaces and digits take first priority. If only the first name was entered in the directory, this is incorporated into the sort order instead of the surname. The sort order is as follows: 1. Space 2. Digits (0–9) 3. Letters (alphabetical) 4. Other characters To get round the alphabetical order of the entries, insert a space or a digit in front of the first letter of the surname. These entries will then move to the beginning of the directory.
Selecting entries in the directory and call-by-call list s / C Open directory or call-by-call list. You have the following options: u Use s to scroll through the entries until the required name is selected. u Enter the first character of the name (in the directory: first character of the surname or of the first name if only the first name has been entered), or scroll to the entry using s.
Dialling with the directory/call-by-call list
s / C ¢ s (select entry) c Press the talk key. The number is dialled.
Version 4, 16.09.2005
Managing entries in the directory/callby-call lists s/C
¢ s (select entry)
Viewing entries §View§
Press the display key. The entry is displayed. Back with §OK§.
Editing entries Press display keys one after the other. Carry out changes and save.
§View§ §Edit§
¤
Using other functions
s / C ¢ s (select entry) ¢ §Options§ (open menu) The following functions can be selected with q: Display Number To edit or add to a saved number, or to save it as a new entry, press Ó after the number is displayed. Edit Entry Edit selected entry. Delete Entry Delete selected entry. VIP Entry (directory only) Mark a directory entry as a VIP (Very Important Person) and assign a specific ringer tone to it. You can then recognise important calls from the ringer tone. Precondition: Calling Line Identification (page 16). Copy Entry Send a single entry to a handset (page 22). Delete List Delete all entries in the directory/callby-call list. Copy List Send complete list to a handset (page 22). Available Memory Display the available entries in the directory and call-by-call list (page 20).
21
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / direct_charges.fm / 9.7.07
Using the directory and lists
Using quick dial keys
¤ Press and hold the required quick dial key (page 41).
Sending the directory/call-by-call list to another handset Preconditions: u The sending and receiving handsets
must both be registered on the same base station. u The other handset and the base station can send and receive directory entries. s / C ¢ s (select entry) ¢ §Options§ (open menu) ¢ Copy Entry / Copy List ¢ to Internal s Select the internal number of the receiving handset and press §OK§. You can transfer several individual entries one after another by responding to Copy next entry? with §Yes§. A successful transfer is confirmed by a message and confirmation tone on the receiving handset.
Please note:
You can also send the complete directory via data transfer, without opening the directory:
w ¢ í ¢ Data Transfer ¢ Directory
Please note: u Entries with identical numbers are not
overwritten on the receiving handset.
u The transfer is cancelled if the phone
rings or if the memory of the receiving handset is full.
Version 4, 16.09.2005
Transferring the directory as a vCard with Bluetooth In Bluetooth mode (see page 48) you can transfer directory entries in vCard format, e.g. to exchange entries with your mobile. s ¢ s (select entry) ¢ §Options§ (open menu) ¢ Copy Entry / Copy List ¢ vCard via Bluetooth 22
The list of "Known Devices" (see page 49) is displayed. s Select device and press §OK§.
Receiving a vCard with Bluetooth If a device from the "Known Devices" list (see page 49) sends a vCard to your handset, this occurs automatically and you are informed about it via the display. If the sending device does not appear in the list, you will be asked on the display to enter the device PIN for the sending device: ~ Enter the PIN for the sending Bluetooth device and press §OK§. The transferred vCard is available as a directory entry.
Copying a displayed number to the directory You can copy numbers to the directory that are displayed in a list, e.g. the call history or the last number redial list, in an SMS or during a call to the directory. A number is displayed: §Options§ ¢ Copy to Directory ¤ Complete the entry, see page 20.
Copying a number or e-mail address from the directory In many operating situations, you can open the directory to copy a number or e-mail address, for example. Your handset need not be in idle status. ¤ Depending on the operating situation, open the directory with s or Ò or ¨ Directory. q Select an entry (page 21).
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / direct_charges.fm / 9.7.07
Using the directory and lists
Saving an anniversary in the directory
Viewing missed anniversaries
For each number in the directory, you can save an anniversary and specify a time at which a reminder call should be made on the anniversary (delivery status: Annivers.: Off). Anniversaries are automatically recorded in the calendar (page 47). s ¢ s (select entry; page 21) §View§ §Edit§ Press display keys one after the other. s Scroll to the Annivers.: line. v Select On. ¤ Change multiple line input: Anniversary (Date) Enter day/month/year in 8-digit format. Annivers. (Time) Enter the hour/minute for the reminder call in 4-digit format. Annivers. (Signal) Select the type of signal for the reminder. ¤ Save changes: (page 59).
In idle status, you are reminded of an elapsed and unacknowledged anniversary by the one-off display of §Appoint.§. ¤ View appointment: §Appoint.§ Press the display key. You now have the following options:
Deactivating anniversaries
Manual last number redial
s
¢ s (select entry; page 21)
§View§ §Edit§
s v §Save§
Press display keys one after the other. Scroll to the Annivers.: line. Select Off. Press the display key.
Reminder call on an anniversary
Version 4, 16.09.2005
A reminder call is signalled on the handset using the selected ringer tone. You now have the following options: §SMS§ Write an SMS. §OFF§ Press the display key to acknowledge and end the reminder call.
Write an SMS. §Delete§ Delete reminder. After deleting, press the ” or §Go Back§ display key: Back to idle status, §Appoint.§ is no longer displayed. You can also view missed anniversaries afterwards (see page 48). §SMS§
Last number redial list The last number redial list contains the twenty numbers last dialled with the handset (max. 32 digits). If one of the numbers is in the directory or in the callby-call list, the corresponding name will be displayed.
c s c
Press the key briefly. Select entry. Press the talk key again. The number is dialled. When a name is displayed, you can display the corresponding phone number by pressing the §View§ display key.
Managing entries in the last number redial list c s
Press the key briefly. Select entry. §Options§ Open menu. The following functions can be selected with q: Copy to Directory Copy an entry to the directory (page 20). 23
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / direct_charges.fm / 9.7.07
Using the directory and lists Automatic Redial The selected number is automatically dialled at fixed intervals (at least every 20 seconds). The handsfree key flashes and "open listening" is activated. – Party answers: press the talk key c. The function is ended. – Party does not answer: the call is terminated after approx. 30 seconds. The function is ended after pressing any key or after ten unsuccessful attempts. Display Number (as in the directory, page 21) Delete Entry (as in the directory, page 21) Delete List (as in the directory, page 21)
Opening lists with the message key You can use the message key f to open the following list selection: u SMS list If several mailboxes are set up (page 31), several lists are displayed. u Network mailbox, if your network provider supports this function and the network mailbox is set for fast access (page 35). u Call history An advisory tone sounds as soon as a new message arrives in a list. The message key f flashes (it goes off when the key is pressed). In idle status, the display shows an icon for the new message: Icon
New message...
Ã
... on the network mailbox
Á
Version 4, 16.09.2005
À
... in the call history ... in SMS list
The number of new entries is shown beneath the corresponding icon.
24
List selection If you press the message key f, only the lists that contain messages are shown (exception: network mailbox). Lists with new messages are identified in bold: Messages & Calls Mailboxes:
(2)
SMS: Calls List:
(1) (4)
”
OK
Select a list with q. To open, press w or §OK§. If only one list contains entries, no list selection is offered and the relevant list is displayed immediately.
Incoming SMS message list All received SMS messages are saved in the incoming message list, page 29.
Call history Precondition: Calling Line Identification (CLIP, page 16) Depending on the type of list set, the call history contains u accepted calls ( ‰ ) u missed calls Depending on the type of list set, all numbers of the last 30 incoming calls are stored or only the missed calls. You can also call up the call history via the menu: w ¢ Calls List
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / direct_charges.fm / 9.7.07
Making cost-effective calls
Setting the call history type
w ¢ Ð ¢ Base ¢ Calls List Type Missed Calls / All Calls Select and press §OK§ ( ‰ = on).
a Press and hold (idle status). The call history entries are retained when you change the list type.
List entry New messages are on top. Example of list entries: All Calls Susi Sorglos 29/11/07
12:20
Louise Miller 29.11.07 Delete
‰
11:15 Options
u List type (in header) u Status of entry
Bold: new entry
Version 4, 16.09.2005
u Number or name of caller
You can add the caller's number to the directory (page 22). u Date and time of call (if set, page 9) u Type of entry: – accepted calls ( ‰ ) – missed calls Pressing the display key §Delete§ deletes the marked entry. After pressing the display key §Options§ you can select more functions with q: Copy to Directory Copying a displayed number to the directory. Delete List Delete complete list. When you quit the call history, all entries are set to the status "old", i.e. the next time you call the list up they will no longer be shown in bold.
Making cost-effective calls Sign up with a network provider who offers particularly low-cost call rates (callby-call). You can manage the numbers in the call-by-call list.
Linking call-by-call numbers with one number You can insert the dialling code of a network provider ahead of the number ("linking"). C Open call-by-call list. s Select entry (call-by-call number). §Options§ Press the display key. Display Number Select and press §OK§. ~ Enter number or select number from the directory (page 22). c Press the talk key. Both numbers are dialled.
Automatic network provider preselection (Preselection) You can specify a call-by-call number (preselection number), which is automatically placed in front of numbers when you dial them. u The "with preselection" list contains the "rule" for dialling code numbers or the first digits of dialling code numbers with which you wish the preselection number to be used. u The "without preselection" list contains the "exception to the rule". Example: You have entered 08 for "with preselection". Now all numbers that start with 08 will be dialled with preselection.
25
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / direct_charges.fm / 9.7.07
Making cost-effective calls If, for example, you want 081 to still be dialled without preselection, enter 081 for "without preselection". When dialling, the first digits of the selected numbers are compared with both lists after the talk/handsfree key is pressed: u The preselection number is not prefixed if the dialled number – does not match any entries in the two lists – matches an entry in the "without preselection" list u The preselection number is prefixed if the first digits of the dialled number match with only one entry in the list "'with preselection".
Saving preselection numbers
w ¢ Ð ¢ Base ¢ Preselection ¢ Preselect No. ~ Enter or change the preselection number (call-by-call number). Save§ Press the display key. a Press and hold (idle status).
Save or change entries in the preselection lists
Version 4, 16.09.2005
Each of the two lists can contain 20 entries, each with 6 digits. Numbers may be prefixed according to the country in the "with preselection" list. This means e.g. that all national calls or calls to the mobile network are automatically linked to the preselection number you have stored previously.
26
w ¢ Ð ¢ Base ¢ Preselection ¢ With Preselect / Without Presel. s Select entry. §Edit§ Press the display key. ~ Enter or edit first digits of number. Save§ Press the display key. a Press and hold (idle status).
Temporarily cancelling preselection c (press and hold) ¢ §Options§ ¢ Aut Preselct off
Permanently deactivating preselection
¤ Delete the preselection number (page 26).
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / sms_BRD_neutral.fm / 9.7.07
SMS (text messages)
SMS (text messages)
Please note:
Your unit is supplied ready for sending SMS messages immediately.
u To receive SMS messages you must be
Preconditions: u Calling Line Identification is enabled for
your phone line. u Your network provider supports SMS in the fixed network (information on this can be obtained from your network provider). u You are registered with your service provider to send and receive SMS. SMS messages are exchanged between SMS centres operated by service providers. You must enter the SMS centre through which you wish to send and receive SMS messages into your phone. You can receive SMS messages from every SMS centre that is entered, provided you have registered with your service provider. Your SMS messages are sent through the SMS centre that is entered as the active send service centre (page 32). Only one SMS centre can be the active send service centre at any one time. If no SMS Service Centre is entered, the SMS menu only contains the entry Settings. Enter an SMS Service Centre (page 32). Information on writing an SMS can be found in the appendix: u For how to enter text, see page 59. u Writing using the predictive text tool EATONI, see page 59.
u If your phone is connected to a PABX,
please read page 33.
registered with your service provider.
Writing/sending an SMS Writing an SMS
w¢î Mailbox 2 Select mailbox if necessary and press §OK§. ~ Enter mailbox PIN if necessary and press §OK§. New SMS Select and press §OK§. ~ Write an SMS.
Please note: – Instructions on entering text can be found on page 59, and on writing with EATONI predictive text on page 59. – EATONI is activated as a default setting. Activating/deactivating EATONI page 60.
Sending an SMS c or:
Press the talk key
§Options§
Press the display key. Select and press §OK§. Select and press §OK§.
Send SMS
~/s /C
Rules u An SMS can be up to 612 characters. u If there are more than 160 characters,
Version 4, 16.09.2005
the SMS is sent as a linked SMS (up to 4 messages with 153 characters each).
§Send§
Select number with area code (even if you are in that area) from the directory or call-bycall list, or enter number directly. For SMS to an SMS mailbox: add the mailbox ID to the end of the number. Press the display key. The SMS is sent.
27
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / sms_BRD_neutral.fm / 9.7.07
SMS (text messages)
Please note: – If you are interrupted by an external call while writing an SMS, the text is automatically saved in the draft message list. – If the memory is full, or if the SMS function on the base station is being used by another handset, the operation is cancelled. An appropriate message appears in the display. Delete SMS messages you no longer require or send the SMS later.
Setting input language
¤ You are writing an SMS (page 27).
Press the display key. Select Language Select and press §OK§. s Select input language and press §OK§.
§Options§
a
Press the end call key briefly twice to return to the text panel. The input language setting only applies to the current SMS.
SMS status report Precondition: Your network provider supports this feature. If you have activated the status report, you will receive an SMS with a confirmation message after sending.
Activating/deactivating a status report
w ¢ î ¢ Settings Status Report Select and press §OK§ ( ‰ = on).
Reading/deleting status report/saving number to directory
Version 4, 16.09.2005
¤ Open the incoming message list
(page 29) and then: q Select SMS with the State OK or State not OK status. §Read§ Press the display key. u Delete: §Options§ Delete Entry §OK§.
28
u Save to directory:
§Options§ Copy to Directory §OK§.
u Delete entire list:
§Options§ Delete List §OK§.
Draft message list You can save an SMS in the draft message list and edit and send it later.
Saving an SMS in the draft message list
¤ You are writing an SMS (page 27).
Press the display key. Save Entry Select and press §OK§. §Options§
Opening the draft message list
w ¢ î ¢ (mailbox, mailbox PIN) ¢ Outgoing (3) The first list entry is displayed, e.g.: 1234567890 21.11.07 09:45
Reading or deleting individual SMS messages
¤ Open the draft message list and then:
q
Select SMS. Press the display key. The entry will be displayed. Scroll line by line using q. Or delete the SMS with §Options§ Delete Entry §OK§. §Read§
Writing/changing an SMS
¤ You are reading an SMS in the draft
message list. §Options§ Open menu. You have the following options: New SMS Write a new SMS and then send (page 27) or save it. Edit Edit the text of the saved SMS and then send (page 27). Character Set Text is shown in the selected character set.
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / sms_BRD_neutral.fm / 9.7.07
SMS (text messages)
Deleting draft message list
¤ Open the draft message list and then: §Options§
Delete all a
Open menu. Select, press §OK§ and confirm with §Yes§. The list is cleared. Press and hold (idle status).
Sending SMS messages to an e-mail address If your service provider supports the SMS as e-mail feature, you can also send your SMS messages to e-mail addresses. The e-mail address must be at the beginning of the text. You must send the SMS to the e-mail service of your SMS send centre. w ¢ î ¢ (mailbox, mailbox PIN) ¢ New SMS Œ/~ Load the e-mail address from the directory or enter it directly. End the entry with a space or colon (depending on the service provider). ~ Enter the SMS text. §Options§ Press the display key. Send Select and press §OK§. E-mail Select and press §OK§. If the number of the e-mail service is not entered (page 32), enter the number of the e-mail service. §Send§ Press the display key.
Receiving an SMS All received SMS messages are saved in the incoming message list. Linked SMS messages are displayed as one message. If this is too long or is not transferred completely, it is split into individual messages. Since an SMS remains in the list even after it has been read, you should regularly delete SMS messages from the list. The display tells you if the SMS memory is full. ¤ Deleting SMS messages you no longer require (page 30).
Incoming message list The incoming message list contains: u All received SMS messages, starting with the most recent. u SMS messages that could not be sent due to an error. New SMS messages are signalled on all Gigaset SL37H handsets by the À icon in the display, the flashing message key f and an advisory tone.
Opening the incoming message list with the f key
f Press. Select mailbox if necessary and enter mailbox PIN. The incoming message list is displayed as follows (example): SMS:
(2)
1 2
1 bold: number of new entries regular: number of read entries 2 Name of mailbox, here: general mailbox Open list with §OK§.
An entry in the list is displayed e.g. as follows: Version 4, 16.09.2005
1234567890 21.11.05 09:45
29
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / sms_BRD_neutral.fm / 9.7.07
SMS (text messages)
Opening the incoming message list via the SMS menu w ¢ î ¢ (mailbox, mailbox PIN) ¢ Incoming (2)
Reading or deleting individual SMS messages
Adding the sender's number
¤ Open incoming message list and select
entry (page 29). Press the display key. For further information, see page 22.
§Options§
¤ Open the incoming message list. ¤ Continue as described in "Reading or
Please note:
Deleting the incoming message list
Copying/dialling numbers from an SMS text
deleting individual SMS messages", page 28. After you have read a new SMS, it is given the status "Old" (is no longer shown in bold). All new and old SMS messages in the list are deleted. ¤ Open the incoming message list. §Options§ Open menu. ¤ To continue, see "Deleting draft message list", page 29.
Replying to or forwarding SMS messages
¤ Read the SMS (page 30):
Press the display key. You have the following options: Reply Write and send a reply SMS directly (page 27). Edit Edit the text in the SMS and then send it (page 27).
§Options§
Forwarding an SMS
¤ You are reading an SMS (page 30): §Options§
Forward
Version 4, 16.09.2005
Adding a number to the directory
30
Press the display key. Select and press §OK§. For further information, see page 27.
– You can create a special directory for SMS messages within your main directory by putting a star (*) before the names. – An attached mailbox identifier is added to the directory.
¤ Read SMS (page 30) and scroll to the
telephone number. The digits are reverse-highlighted. Ó Press the display key. For further information, see page 22. Or: c Press the talk key to dial the number. If you wish to use the number to send an SMS: ¤ Save the number with the local area code (dialling code) in the directory.
Changing the character set
¤ Read the SMS (page 30):
Press the display key. Character Set Text is shown in the selected character set. §Options§
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / sms_BRD_neutral.fm / 9.7.07
SMS (text messages)
Notification by SMS
SMS mailboxes
You can have yourself notified about missed calls. Precondition: For missed calls, the caller's number (CLI) must have been transmitted. Notification is sent to your mobile phone or another phone with SMS functionality. You only need to set the phone number to which notification should be sent (notification number) and the notification type.
The General Mailbox is the default setting. Anyone can access this mailbox and it cannot be protected by a PIN. You can additionally set up three personal mailboxes and protect these with a PIN. Each mailbox is identified by a name and a "Mailbox ID" (a kind of extension number).
Storing the notification number
w ¢ î ¢ Settings ¢ Notify Number ~ Enter the number to which the SMS should be sent. §Save§ Press the display key. a Press and hold (idle status).
Warning:
Do not enter your own fixed network number for the notification of missed calls. This can lead to chargeable endless looping.
Setting the notification type
Version 4, 16.09.2005
w ¢ î ¢ Settings ¢ Notify Type ¤ Change multiple line input if necessary: Missed Calls: Set On if you require SMS notification. ¤ Save changes (page 59).
Please note: u If you operate a number of devices
(base stations) with SMS functionality on a single phone line, then each SMS mailbox ID may only occur once. In this case you must also change the preset ID of the general mailbox ("0"). u You can only use personal mailboxes if your service provider supports this function. You can tell whether this is the case by the addition of a star (*) to the number of a (preset) SMS centre. u If you have forgotten your mailbox PIN, you can reset it by restoring the base station's default settings. This will delete all SMS messages from all mailboxes.
Setting up and changing a personal mailbox Setting up a personal mailbox
w ¢ î ¢ Settings ¢ SMS Mailboxes s Select a mailbox, e.g. Mailbox 2 and press §OK§. ¤ Change multiple line input: On/Off: Activate or deactivate mailbox. ID: Select mailbox ID (0–9). You can only select the available numbers. Protection: Activate/deactivate PIN protection. PIN If necessary, enter 4-digit PIN. ¤ Save changes (page 59). 31
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / sms_BRD_neutral.fm / 9.7.07
SMS (text messages) Active mailboxes are marked with ‰ in the mailbox list. They are shown in the SMS list and can, if necessary, be displayed by pressing the message key f.
Deactivating a mailbox
¤ Set On/Off: to Off. Confirm message with §Yes§ if necessary.
All SMS messages saved in this mailbox will be deleted.
Deactivating PIN protection
¤ Set Protection: to Off.
The mailbox PIN is reset to "0000".
Changing the name of a mailbox
w ¢ î ¢ Settings ¢ SMS Mailboxes ¢ s (select mailbox) §Edit§ Press the display key. ~ Enter new name. §Save§ Press the display key. a Press and hold (idle status).
Changing a mailbox's PIN and ID
w ¢ î ¢ Settings ¢ SMS Mailboxes ¢ s (select mailbox) ~ Enter mailbox PIN if necessary und press §OK§. ¤ Set ID:, Protection: and PIN (page 31).
Sending an SMS to a personal mailbox
Version 4, 16.09.2005
To send an SMS to a personal mailbox, the sender must know your ID and enter it after your number. ¤ You can send your SMS contact an SMS via your personal mailbox. Your SMS contact will receive your SMS number with current ID and can save it in their directory. If the ID is invalid, the SMS will not be delivered.
32
Setting SMS centres Entering/changing SMS centres
¤ You should find out about the services
and special functions offered by your service provider before you make a new application and/or before you delete pre-configured call numbers. w ¢ î ¢ Settings ¢ Service Centres s Select SMS centre (e.g. Service Centr. 1) and press §OK§. ¤ Change multiple line input: Active Send: Select Yes if SMS messages are to be sent via the SMS centre. SMS: Press the display key §Edit§. Enter the number of the SMS service and insert a star if your service provider supports personal mailboxes. E-mail: Press the display key §Edit§. Enter the number of the e-mail service. ¤ Save changes (page 59).
Please note:
Ask your service provider for details on how to enter service numbers if you wish to use personal mailboxes (precondition: your service provider supports this function).
Sending an SMS through another SMS centre
¤ Activate the SMS centre (2 to 4) as active send service centre.
¤ Send the SMS.
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / sms_BRD_neutral.fm / 9.7.07
SMS (text messages)
SMS info services
SMS on a PABX
You can have your service provider send you certain information (e.g. weather forecasts or lottery numbers) via SMS. A total of up to 10 info services can be stored. You can obtain information about the info services available and their costs from your service provider.
u You can only receive an SMS when the
Setting up/ordering an info service Ordering an info service
w ¢ î ¢ SMS Service s Select info service. §Send Press the display key.
Setting up an info service
¤ Select an empty entry, delete before-
hand if necessary. Then: §Edit§ Press the display key. ~ If necessary, enter code, designation and destination number. §Save§ Press the display key.
Editing the entry of an info service
¤ Select the info service (see above). Then:
§Options§ Edit Entry
~ §Save§
Opening menu. Select and press §OK§. If necessary, change the code, designation, or destination number. Press the display key.
Deleting an info service
¤ Select the info service (see above). Then:
Open menu. Delete Entry Select and press §OK§.
Version 4, 16.09.2005
§Options§
Calling Line Identification is forwarded to the extension of the PABX (CLIP). The CLIP of the phone number for the SMS centre is evaluated in your Gigaset. u If required, you must prefix the number for the SMS centre with the access code (depending on your PABX). If in doubt, test your PABX, e.g. by sending an SMS to your own number, once with and once without the access code. u When you send SMS messages, your sender number may be sent without your extension number. In this case the recipient cannot reply to you directly. Sending and receiving SMS messages on ISDN PABXs is only possible via the MSN number assigned to your base station.
Activating/deactivating the SMS function If you deactivate the SMS function, you cannot send or receive any SMS messages with your phone. The settings which you have made for sending and receiving SMS messages (e.g. the call numbers of the SMS centres) and the entries in the incoming and draft message lists are saved even after you switch off your phone. w Open menu. N5O2L Enter the digits. Q §OK§ Deactivate SMS function. Or:
§OK§ Activate SMS function (default setting).
33
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / sms_BRD_neutral.fm / 9.7.07
SMS (text messages)
SMS troubleshooting Error codes when sending E0 Calling Line Identification permanently withheld (CLIR) or Calling Line Identification not activated. FE Error occurred during SMS transfer. FD Connection to SMS centre failed, see selfhelp.
Self-help with errors The following table lists error situations and possible causes and provides notes on troubleshooting. You cannot send messages. 1. You have not requested the CLIP service (Calling Line Identification Presentation). Ask your service provider to enable this service.
¥
2. SMS message transmission has been interrupted (e.g. by a call). Re-send the SMS.
¥
3. Network provider does not support this feature. 4. No number or an invalid number is entered for the SMS centre set as the active send service centre. Enter the number (page 32).
¥
You receive an incomplete SMS. 1. Your phone's memory is full. Delete old SMS messages (page 30).
¥
2. The service provider has not yet sent the rest of the SMS. You have stopped receiving SMS messages. 1. You have changed the ID of your mailbox. Give your SMS contacts your new ID or undo the change (page 32).
¥
2. You have not activated your mailbox. Activate your mailbox (page 32).
¥
Version 4, 16.09.2005
3. Call diversion is activated with When: All Calls or the call diversion All Calls is activated for the network mailbox. Change the call diversion.
¥
34
The message is played back. 1. The "display call number" service is not activated. Ask your service provider to activate this function (chargeable).
¥
2. Your mobile phone operator and your fixed network SMS service provider have not agreed on a co-operation. Obtain information from your fixed network SMS service provider.
¥
3. Your terminal is recorded by your SMS provider as having no fixed network SMS functionality, i.e. you are no longer registered with the provider. Obtain information from your fixed network SMS service provider. Have the device (re-)registered to receive SMS messages.
¥ ¥
Messages are only received during the day. The terminal is recorded in your SMS provider's database as having no fixed network SMS functionality, i.e. you are no longer registered with the provider. Obtain information from your fixed network SMS service provider. Have the device (re-)registered to receive SMS messages.
¥ ¥
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / T-NetBox_SAG.fm / 9.7.07
Using the network mailbox
Using the network mailbox The network mailbox is your network provider's answer machine within the network. You cannot use the network mailbox unless you have requested it from your network provider.
Configuring fast access for the network mailbox With fast access, you can dial the network mailbox directly. Fast access is set for the network mailbox. You only need to enter the number of the network mailbox.
Viewing the network mailbox report When a message is recorded, you receive a call from the network mailbox. If you have requested Calling Line Identification, the network mailbox number will be displayed. If you take the call, the new messages are played back. If you do not take the call, the network mailbox number will be saved in the missed calls list and the message key flashes (page 24).
Configuring fast access for the network mailbox and entering the network mailbox number
w ¢ Ð ¢ Voice Mail ¢ Set Key 1 Network Mailb. Select and press §OK§ ( ‰ = on).
~
Enter the number for the network mailbox. §Save§ Press the display key. a Press and hold (idle status). The setting for fast access applies to all Gigaset SL37H handsets.
Calling the network mailbox
Version 4, 16.09.2005
d
Press and hold. You are connected straight to the network mailbox. Press handsfree key d if required. You will hear the network mailbox announcement.
35
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / registr_sett.fm / 9.7.07
Using several handsets
Using several handsets Registering handsets You can register up to six handsets to your base station. A Gigaset SL37H handset can be registered to up to four base stations.
Manually registering the Gigaset SL37H to Gigaset SL370 You must initiate handset registration on the handset and on the base station. Once it has been registered, the handset returns to idle status. The internal number of the handset appears in the display, e.g. INT 1. If it does not, repeat the procedure.
On the handset
w ¢ Ð ¢ Handset ¢ Register H/Set s Select base station, e.g. Base 1 and press §OK§. ~ Enter the system PIN of the base station (the default is 0000) and press §OK§. The following flashes in the display, e.g. Base 1.
On the base station Within 60 sec. press and hold the registration/paging key on the base station (page 1) (approx. 3 sec.).
Registering other handsets You can register other Gigaset handsets and handsets for other devices with GAP functionality as follows.
On the handset
¤ Start to register the handset as Version 4, 16.09.2005
described in its user guide.
36
On the base station Press and hold the registration/paging key on the base station (page 1) (approx. 3 sec.).
De-registering handsets You can de-register any other registered handset from any registered Gigaset SL37H handset. u Open list of internal parties. The handset you are currently using is indicated by < . s Select the internal party you wish to de-register. §Options§ Open menu. De-reg. H/Set No. Select and press §OK§. ~ Enter the current system PIN and press §OK§. §Yes§ Press the display key.
Locating a handset ("paging") You can locate your handset using the base station. ¤ Briefly press the registration/paging key on the base station (page 1). ¤ All handsets will ring simultaneously ("paging"), even if the ringer tones are switched off.
Ending paging
¤ Briefly press the registration/paging
key on the base station or press the talk key c on the handset.
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / registr_sett.fm / 9.7.07
Using several handsets
Changing the base station If your handset is registered to more than one base station, you can set it to a particular base station or to the base station that has the best reception (Best Base). w ¢ Ð ¢ Handset ¢ Select Base s Select one of the registered base stations or Best Base and press §OK§.
Making internal calls Internal calls to other handsets registered on the same base station are free.
Calling a specific handset u ~ Or: u s c
Initiate internal call. Enter the number of the handset. Initiate internal call. Select handset. Press the talk key.
Calling all handsets ("group call") u *
Initiate internal call. Press the star key. All handsets are called.
Ending a call a
Press the end call key.
Version 4, 16.09.2005
Transferring a call to another handset You can transfer an external call to another handset (connect). u Open list of handsets. The external participant hears hold music if activated (see page 51). s Select a handset or Call All and press §OK§. When the internal participant answers: ¤ If necessary announce the external call. a Press the end call key.
The external call is transferred to the other handset. If the internal participant does not answer or the line is busy, press the display key §End§, to return to the external call. When transferring a call you can also press the end call key a before the internal participant answers. Then, if the internal participant does not answer or the line is busy, the call will automatically return to you (the display will show Recall).
Internal consultation/conference calls When you are speaking to an external participant, you can call an internal participant at the same time for consultation or hold a conference call between all 3 participants. You are conducting an external call. u Open list of handsets. The external participant hears hold music if activated (see page 51). s Select handset and press §OK§. You are connected with the internal participant. Either: §End§ Press the display key. You are reconnected with the external participant. Or: §Conference§ Press the display key. All 3 participants are connected with each other.
Ending a conference call a Press the end call key. If an internal participant presses the end call key a, the other handset remains connected to the external participant.
37
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / registr_sett.fm / 9.7.07
Using several handsets
Accepting/rejecting call waiting If you receive an external call during an internal call, you will hear the call waiting tone (short tone). The caller's number will appear in the display if Calling Line Identification is enabled.
Ending an internal call, accepting an external call Press the display key. The internal call is ended. You are connected to the external caller. §Accept§
Rejecting the external call Press the display key. The call waiting tone is turned off. You remain connected with the internal participant. The ringer tone can still be heard on other registered handsets.
§Reject§
Listening in to an external call Precondition: The Listening In function must be activated. You are conducting an external call. An internal participant can listen in on this call and take part in the conversation. All the participants are made aware of the "listening in" by a signal tone.
Ending listening in a Press the end call key. All participants hear a signal tone. If the first internal participant presses the end call key a, the handset that has "listened in" remains connected to the external participant.
Changing the name of a handset The names "INT 1", "INT 2" etc. are assigned automatically at registration. You can change these names. The name must be no more than 10 characters. The changed name is displayed in every handset's list. u Open list of handsets. Your own handset is indicated by <. s Select handset. §Edit§ Press the display key. ~ Enter name. §Save§ Press the display key.
Activating/deactivating internal listening-in
Changing a handset's internal number
Internal listening-in
A handset is automatically assigned the lowest free number on registration. If all slots are occupied, number 6 is overwritten if this handset is in idle status. You can change the internal number of all registered handsets (1–6). u Open list of handsets. Your own handset is indicated by <. §Options§ Open menu. Edit H/Set No. Select and press §OK§. The list of handsets is displayed.
w ¢ Ð ¢ Base ¢ Add. Features ¢ Listening In Press §OK§ to switch the function on or off ( ‰ = on). a Press and hold (idle status).
Version 4, 16.09.2005
You are linked into the call. All participants hear a signal tone. During this time, this handset displays the Conference message and it is not possible to dial another number from this handset.
The line is engaged with an external call. Your screen will display information to that effect You want to listen in to the external call. c Press and hold the talk key. 38
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / registr_sett.fm / 9.7.07
Using several handsets s
The current number flashes. Select a handset. ~ Enter the new internal number (1–6). The handset's old number is overwritten. §Save§ Press the display key to save the input. a Press and hold (idle status). You will hear the error tone (descending tone sequence) if you assign an internal number twice. ¤ Repeat the procedure with a free number.
Using a handset as a room monitor
Version 4, 16.09.2005
If the room monitor is activated, a previously stored destination number is called as soon as a set noise level is reached. You can store an internal or external number in your handset as the destination number. The room monitor call to an external number stops after around 90 seconds. The room monitor call to an internal number (handset) stops after approx. 3 minutes (depending on the base station). While the room monitor is activated, all keys are locked except the end call key. The handset's speaker is muted. When the room monitor is activated, incoming calls to the handset are indicated without a ringer tone and are only shown on the screen. The display and keypad are not illuminated and advisory tones are also turned off. If you accept an incoming call, the room monitor mode is suspended for the duration of the call, but the function remains activated. If you deactivate then reactivate the handset, the room monitor mode remains activated.
Caution! – You should always check the operation of the room monitor before use. For example, test its sensitivity. Check the connection if you are diverting the room monitor to an outside number. – When the function is switched on the handset's operating time is severely reduced. If necessary, place the handset in the charging cradle. This ensures that the batteries do not run down. – Ideally the handset should be positioned 1 to 2 metres away from the baby. The microphone must be directed towards the baby. – The connection to which the room monitor is diverted must not be blocked by an activated answer machine.
Activating the room monitor and entering the number to be called
v ¢ í ¢ Room Monitor ¤ Change multiple line input: Room M.: Select On to activate. Call to: External number: Select the number from the directory (press display key Ò) or enter it directly. Only the last 4 digits are displayed. Internal number: §Options§ ¢ INT ¢ §OK§ ¢ s (select handset or Call All if all registered handsets are to be called) ¢ §OK§.
Level: Set noise level sensitivity (Low or High). ¤ Press §Save§ to save the settings.
Changing the set destination number
v ¢ í ¢ Room Monitor s Scroll to the Call to: line. X or §Delete§ Delete existing number. ¤ Enter and save number as described in "Activating the room monitor and entering the number to be called" (page 39). 39
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / registr_sett.fm / 9.7.07
Using several handsets
Deactivating the room monitor remotely Preconditions: The phone must support touch tone dialling and the room monitor should be set for an external destination number. ¤ Accept the call from the room monitor and press keys 9 ;. The room monitor function will deactivate after the call ends. There will be no further room monitor calls. The other room monitor settings (e.g. no ringer tone) on the handset will remain activated until you press the display key §OFF§ on the handset. To reactivate the room function with the same phone number: ¤ Turn on the activation again and save with §Save§ (page 39).
Walky-talky mode Walky-talky mode allows two handsets to communicate with each other, both inside and outside the range of the base station to which the handsets are registered. Handsets that are to communicate with each other using walky-talky mode must meet one of the following conditions: u The handsets are all registered to the same base station. u The handsets are set to Best Base or are not yet registered. In walky-talky mode, if you press the talk key c or the handsfree key d, the call will go to all handsets that are in walkytalky mode. The connection is made with the first handset to accept the walky-talky call.
Please note: u The maximum range outdoors is
Version 4, 16.09.2005
300 m.
u Handsets that are in walky-talky mode
are not available for phone calls. u The handset operating times are greatly curtailed. 40
Activating/deactivating walky-talky mode
v ¢ í ¢ Walky-Talky Use §OK§ to activate walky-talky mode. You can now: §OFF§ Press the display key. Walkytalky mode is switched off. or > Press the display key to open the menu. The following functions can be selected with q: Audio Settings You can set Ringer Settings (see page 44) and Advisory Tones (see page 46) for walky-talky mode. Room Monitor You can use the handset in walky-talky mode as a room monitor.
Using a handset in walky-talky mode as a room monitor
¨ ¢ Room Monitor ¤ Change multiple line input: Room M.: Select On to activate. Level: Set noise level sensitivity (Low or High). ¤ Save changes (page 59). The room monitor will use all the handsets that are in walky-talky mode. Switch the room monitor off by pressing the display key §OFF§ on the handset that was used to activate the room monitor. The handset reverts to normal walky-talky mode.
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / registr_sett.fm / 9.7.07
Handset settings
Handset settings Your handset is preconfigured, but you can change these settings to suit your individual requirements.
Shortcuts for functions and numbers You can assign the left display key and each of the digit keys Q and 2 to O a number or a function. The right display key has a function pre-selected by default. You can change the assigned function. The number is then dialled or the function started by simply pressing a key.
Version 4, 16.09.2005
Assigning a digit key/left display key Precondition: The digit key or the left display key has not yet been assigned a number or a function. ¤ Press the display key } or press and hold the digit key. The list of possible key assignments is opened. The following can be selected: Quick Dial / Call-by-Call Assign key to a number from the directory or call-by-call list. The directory or call-by-call list is opened. ¤ Select an entry and press §OK§. If you delete or edit an entry in the directory or call-by-call list, this has no effect on the assignment to the digit/ display key. Room Monitor Assign key to the menu for setting and activating the room monitor (see page 39). Alarm Clock Assign key to the menu for setting and activating the alarm clock (see page 46).
Calendar Open calendar/enter new appointment. Bluetooth Assign the Bluetooth menu to a key. More Features... More features are available: INT Internal calls (see page 37). SMS Assign the menu for SMS functions to a key (see page 27). SMS Service Assign key with the menu for ordering info services (page 33). SMS Notific. Assign key with the menu for activating SMS notification (page 31). If the left display key has been assigned a shortcut, the selected function or name of the phone number in the directory or callby-call list is displayed (abbreviated if necessary) in the bottom display line via the display key.
Starting the function, dialling the number If the handset is in idle status, press and hold the digit key or press the display key briefly. Depending on the key assignment: u Numbers are dialled directly. u The function menu is opened.
Changing key assignments Display key
¤ Press and hold the left or right display
key. The list of possible key assignments is opened. ¤ Proceed as is described when first assigning the key with a shortcut (page 41).
41
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / registr_sett.fm / 9.7.07
Handset settings
Digit key
¤ Press the digit key briefly.
If you accidentally choose a language you do not understand: w N 4
Press keys in sequence. s Select the correct language and press §OK§.
You can set a picture from the Resource Dir. (page 45) to be displayed as a screensaver when the handset is in idle status. This will replace the idle status display. It may conceal the date, time and name. The screensaver is not displayed in certain situations, e.g. during a call or if the handset is de-registered. If a screensaver is activated, the Screen Saver menu option is marked with ‰ . w ¢ Ð ¢ Display ¢ Screen Saver The current setting is displayed. ¤ Change multiple line input: Activation: Select On (screensaver is displayed) or Off (no screensaver). Selection: If required, change the screensaver (see below). ¤ Save changes: (page 59). If the screensaver conceals the display, briefly press a or w to show the idle display with time and date.
Setting the display
Changing the screensaver
Press the display key. The list of possible key assignments is displayed. Proceed as is described when first assigning the key with a shortcut (page 41).
§Change§
¤
Changing the display language You can view the display texts in different languages. w ¢ Ð ¢ Handset ¢ Language The current language is indicated by ‰ . s Select a language and press §OK§. a Press and hold (idle status).
You have a choice of four colour schemes and several different contrasts. w ¢ Ð ¢ Display Colour Scheme Select and press §OK§. s Select a colour scheme and press §OK§ ( ‰ = current colour). a Press briefly. Contrast Select and press §OK§. r Select contrast. §Save§ Press the display key. a Press and hold (idle status). Version 4, 16.09.2005
Setting the screensaver
42
w ¢ Ð ¢ Display ¢ Screen Saver s Scroll to the Selection line. §View§ Press the display key. The active screensaver is displayed. s Select screensaver and press §Change§. ¤ Save changes: (page 59).
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / registr_sett.fm / 9.7.07
Handset settings
Setting the display backlight Regardless of whether or not the handset is in the charging cradle, you can activate or deactivate the backlighting. If the base station is switched on, the display is permanently dimmed. w ¢ Ð ¢ Display ¢ Backlight The current setting is displayed. ¤ Change multiple line input: In Charger Select On or Off. Without Charger Select On or Off.
Please note:
With the On setting, the standby time of the handset can be significantly reduced. §Save§
a
Press the display key. Press and hold (idle status).
Scroll to the Speaker: line. Set the speaker volume. §Save§§ Press display key if necessary to save the setting. Setting the volume during a call: t Press the control key. r Set the volume.
The setting will automatically be saved after approx. 3 seconds or press the display key §Save§. If t is assigned with another function, e.g. when toggling (page 18): §Options§ Open menu. Volume Select and press §OK§. Configure setting (see above).
Please note:
You can also set the call volume, the ringer tones, advisory tones and the silent alert via the menu (see page 14).
Activating/deactivating auto answer
Changing ringer tones
If you activate this function, when you receive a call you can simply lift the handset out of the charging cradle without having to press the talk key c. w ¢ Ð ¢ Handset Auto Answer Select and press §OK§ ( ‰ = on). a Press and hold (idle status).
You can choose between five volumes (1–5; e.g. volume 2 = ˆ) and the "Crescendo" ring (6; volume increases with each ring = ‰). u Ringer tones: You can select various ringer tones, melodies or any sound from My stuff (page 45). You can set different ringer tones for the following functions: u Ext. Calls: for external calls u Internal Calls: for internal calls u Appointments: for set appointments (page 47) u All: the same ringer tone for all functions
Changing the handsfree/ earpiece volume
Version 4, 16.09.2005
s r
You can set the loudspeaker volume for handsfree talking to five different levels and the earpiece volume to three different levels. In idle status: t ¢ Handset Volume r Set the earpiece volume.
u Volume:
43
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / registr_sett.fm / 9.7.07
Handset settings
Settings for individual functions
Activating/deactivating the ringer tone
Set the volume and melody depending on the type of signalling required. You can activate the time control for external calls to regulate the volume of a call (e.g. quieter at night-time than in daytime). In idle status: t ¢ Ringer Settings q Select setting, e.g. Ext. Calls and press §OK§. r Set volume (1–6). s Scroll to the next line. r Select melody. §Save§ Press the display key to save the setting.
You can deactivate the ringer tone on your handset before you answer a call or when the handset is in idle status; the ringer tone can be deactivated permanently or just for the current call. The ringer tone cannot be reactivated while an external call is in progress.
Additionally for external calls: §Time C.§
Press display key.
¤ Change multiple line input:
Time control : Select On or Off. From: Enter the start of the period in 4-digit format. Until: Enter the end of the period in 4-digit format. Volume: Set the volume (1–6).
Version 4, 16.09.2005
Same ringer tone for all functions
Deactivating the ringer tone permanently * Press and hold the star key. The Ú icon appears in the display when in idle status.
Reactivating the ringer tone *
Press and hold the star key.
Deactivating the ringer tone for the current call §Silence§
Press the display key.
Activating/deactivating the alert tone In place of the ringer tone you can activate an alert tone. When you get a call, you will hear a short tone ("Beep") instead of the ringer tone. * Press and hold the star key and within 3 seconds: §Beep§§ Press the display key. A call will now be signalled by one short alert tone. You will now see º in the display.
Silent alert
In idle status: t ¢ Ringer Settings ¢ All ¤ Set volume and ringer tone (see "Settings for individual functions"). §Save§ Press the display key to confirm the prompt. a Press and hold (idle status).
Incoming calls and other messages are indicated by vibration. In idle status: t ¢ Silent Alert Activate or deactivate with §OK§ ( ‰ = activated).
Please note:
Please note:
You can also set the call volume, the ringer tones, advisory tones and the silent alert via the menu (see page 14).
44
You can also set the call volume, the ringer tones, advisory tones and the silent alert via the menu (see page 14).
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / registr_sett.fm / 9.7.07
Handset settings
My stuff My stuff on the handset manages sounds, which you can use as ringer tones, and pictures (CLIP pictures and screensavers), which you can use as caller pictures or as screensavers. Precondition: Calling Line Identification (CLIP). My stuff can manage the following media types: Icon
Ù Ö
×
Sound
Format
Ringer tones
Standard
Monophonic
Standard
Polyphonic
.mid
Picture (CLIP picture, screensaver)
BMP (128 x 128 or 128 x 64 pixels)
The icon is displayed in front of the name in My stuff. Various mono- and polyphonic sounds and pictures are preconfigured on your handset. You can listen to the available sounds and view the pictures. You can download pictures from a PC (page 60). If there is not enough memory available, you must first delete one or more pictures. The pre-configured pictures are labelled with è. You cannot rename or delete them.
Version 4, 16.09.2005
Playing back sounds/viewing CLIP pictures
w ¢ Ï ¢ Screensavers / Caller Pictures / Sounds (select entry) §Play§ / §View§ Press the display key. Sounds are played back or pictures are displayed. Press the q key to switch between entries. §End§ / ” Press the display key. Playback of the sound or the display of the picture ends. While you are playing back sounds, you can also interrupt playback with the u key.
a Press and hold (idle status). If you have saved a picture in an invalid data format, you will see an error message after selecting the entry. Cancel the operation with Î. Delete the picture with §Delete§.
Sounds: setting the volume During playback: §Volume§ Press the display key. r Set volume. §Save§ Press the display key.
Renaming/deleting a picture You have selected an entry. Options§ Open menu. If a picture cannot be deleted (è), these options are not available. Depending on the situation, you can select the following functions: Delete Entry The selected entry is deleted. Delete List All entries in the list that can be deleted are deleted. Rename Change the name (max. 16 characters) and press §Save§. The entry is stored with the new name.
Checking the memory You can check how much memory is available for screensavers and CLIP pictures. w ¢ Ï ¢ Capacity ” Back: press the display key.
45
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / registr_sett.fm / 9.7.07
Handset settings
Activating/deactivating advisory tones Your handset uses "advisory tones" to tell you about different activities and statuses. The following advisory tones can be activated and deactivated independently of each other: u Key click: every key press is confirmed. u Advisory tones: – Confirmation tone (ascending tone sequence): at the end of an entry/ setting and when an SMS or a new entry arrives in call history – Error tone (descending tone sequence): when you make an incorrect entry – Menu end tone: when scrolling at the end of a menu u Battery low tone: the battery pack requires charging. In idle status: t ¢ Advisory Tones ¤ Change multiple line input: Key Tones: Select On or Off. Confirm.: Select On or Off. Battery: Select On, Off or In Call. The battery warning tone is only activated/deactivated and only sounds during a call. ¤ Save changes: (page 59). You cannot deactivate the confirmation tone for placing the handset in the base station.
Please note:
Version 4, 16.09.2005
You can also set the call volume, the ringer tones, advisory tones and the silent alert via the menu (see page 14).
46
Setting the alarm clock Precondition: The date and time have already been set (page 9).
Activating/deactivating the alarm clock and setting the wake-up time
w¢ì ¤ Change multiple line input: Activation: Select On or Off. Time: Enter the wake-up time in 4-digit format. Occurance: Select Daily or Monday-Friday. Volume: Set the volume (1–6). Melody: Select melody. ¤ Save changes: (page 59). You will see the ì icon. A wake-up call with selected ringer tone (page 43) is signalled on the handset. The wake-up call sounds for 60 seconds. ì is shown in the display. If no key is pressed, the wake-up call is repeated twice at five minute intervals and then switched off. During a call, the wake-up call is signalled by a short tone.
Deactivating the wake-up call/ repeating after a pause (snooze mode) Precondition: A wake-up call is sounding. §OFF§ Press the display key. The wake-up call is deactivated. or §Snooze§ Press the display key or any key. The wake-up call is deactivated and then repeated after 5 minutes. After the second repetition the wake-up call is deactivated completely.
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / registr_sett.fm / 9.7.07
Handset settings
Setting an appointment (calendar) You can have your handset remind you of up to 30 appointments (volume and melody, see page 43).
Version 4, 16.09.2005
Saving an appointment Precondition: The date and time have already been set (page 9). w¢ç r/q Select the day in the graphical calendar and press §OK§ or w. (Days on which appointments have already been saved are highlighted in black.) The list of saved appointments for the day is displayed. If you have already saved 30 appointments, you must first delete an existing appointment. Select and press §OK§. ¤ Change multiple line input: Appoint.: Select On or Off. Date: Enter day/month/year in 8-digit format. Time: Enter hours/minutes in 4-digits format. Notes: Enter text (max. of 16 characters). The text appears as the appointment name in the list and will be displayed on the screen during the appointment reminder. If you do not enter any text, only the date and time of the appointment are displayed. §Save§ Press the display key. a Press and hold (idle status). The appointment is marked with ‰ in the appointments list. The list of appointments is sorted by date. An appointment reminder is signalled with the selected ringer tone (page 43). The appointment reminder sounds for
60 seconds. The entered text, date and time are displayed. During a call, the appointment reminder is signalled by a short tone.
Managing appointments
w¢ç r/q Select the day in the graphical calendar and press §OK§ or w. (Days on which appointments have already been saved are highlighted in black in the calendar.) q Select appointment for the day. §Options§ Open menu. Back with ”§. You have the following options: View Entry View selected appointment, §Options§ Open the menu for editing, deleting and activating / deactivating. Edit Entry Edit selected appointment. Delete Entry Delete selected appointment. Activate / Deactivate Activate / deactivate the selected appointment. Delete List Delete all appointments.
Switching off or answering an appointment reminder Precondition: An appointment reminder is sounding. §§OFF§§ Press the display key to switch off the appointment reminder. Or: §SMS§ Press display key to answer the appointment reminder with an SMS.
47
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / registr_sett.fm / 9.7.07
Handset settings
Displaying missed appointments and anniversaries Missed appointments/anniversaries (page 23) are displayed in the Missed Alarms list if: u You do not accept an appointment/ anniversary. u The appointment/anniversary was signalled during a phone call. u The handset is deactivated at the time of the appointment/anniversary u Automatic redial was activated at the time of an appointment/anniversary (page 23). The most recent entry is at the head of the list. If there is a new appointment/anniversary in the list, the display shows §Appoint.§. Pressing the display key will also open the Missed Alarms list. To open the list from the menu: w ¢ í ¢ Missed Alarms Select appointment/ anniversary. Information about the appointment/anniversary is displayed. A missed appointment is displayed with the appointment name and a missed anniversary is displayed with the last name and first name. The date and time will also be given. §Delete§ Delete appointment §SMS§ Write an SMS. a Press and hold (idle status). If 10 entries are already stored in the list, the next appointment reminder will delete the oldest entry.
Using Bluetooth devices Your Gigaset SL37H handset can communicate wirelessly via Bluetooth™ with other devices using this technology. Before you can use your Bluetooth devices, you must first activate Bluetooth and then register the devices to the handset. You can register 1 Bluetooth headset to the handset. You can also register up to 5 data devices (PC, PDA) to send and receive directory entries as vCards or exchange data with a computer (page 60). In order to transfer phone numbers via Bluetooth connections, it is essential that area codes (international and local area codes) are stored on the phone (see page 50). You will find a description of how to operate your Bluetooth devices in the user guides for these devices.
Please note: – You can only operate headsets on your handset that have the headset profile. – It can take up to 5 seconds to create a connection between your handset and a Bluetooth headset. This applies both when a call is accepted using the headset and one is transferred to the headset, and when a number is dialled from the headset.
Activating/deactivating Bluetooth mode
w ¢ í ¢ Data Transfer ¢ Bluetooth ¢ Activation Press §OK§ to activate or deactivate Bluetooth mode ( ‰ = activated). In idle status, the ò icon on the handset shows that Bluetooth mode is activated:
Version 4, 16.09.2005
Ð
ò INT 1
48
V
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / registr_sett.fm / 9.7.07
Handset settings
Please note: – If Bluetooth is activated and accessories (e.g. data cables page 60) are plugged into the connection socket (page 1), Bluetooth is automatically deactivated. – If a Bluetooth voice connection has already been established, Bluetooth is not deactivated until it is ended. – If a Bluetooth data connection has already been established, the response depends on the receiving device. – Bluetooth is automatically reactivated when the accessories are removed. – If Bluetooth is deactivated and accessories are plugged in, then Bluetooth cannot be activated.
Registering Bluetooth devices The distance between the handset in Bluetooth mode and the activated Bluetooth device (headset or data device) should be no more than 10 m.
Please note: – If you register a headset, any headset that is already registered will be overwritten. – If you would like to use a headset with your handset that is already registered to another device (e.g. to a mobile phone), please deactivate this connection before you start the registration process to Gigaset.
w ¢ í ¢ Data Transfer ¢ Bluetooth ¢ Search Headset / Search Data Device The search can take up to 30 seconds. Once the device has been found, its name will be shown on the display. §Options§ Press the display key. Trust Device Select and press §OK§. ~ Enter the PIN for the Bluetooth device you want to register and press §OK§. The device is saved in the list of known devices. Version 4, 16.09.2005
Cancelling/repeating current search To cancel search: §Cancel§ Press the display key. Repeat search if necessary:
Select and press §OK§. Repeat Search Select and press §OK§. §Options§
Editing the list of known (trusted) devices Open list
w ¢ í ¢ Data Transfer ¢ Bluetooth ¢ Known Devices A corresponding icon appears next to each device name in the list displayed: Icon
Meaning
ô
Bluetooth headset
õ
Bluetooth data device
Viewing entries
Open list ¢ s (select entry) §Options§ Press the display key. View Entry Select and press §OK§. Device name and address are displayed. Back with §OK§.
De-registering a Bluetooth device
Open list ¢ s (select entry) §Options§ Press the display key. Delete Entry Select and press §OK§. a Back: press and hold key.
Please note:
If you de-register an activated Bluetooth device, it may try to reconnect as an "unregistered device".
Changing the name of a Bluetooth device
Open list ¢ s (select entry) §Options§ Press the display key. Rename Select and press §OK§. ~ Change name §Save§
a
Press the display key Back: Press and hold key.
49
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / registr_sett.fm / 9.7.07
Handset settings
Rejecting/accepting an unregistered Bluetooth device
Version 4, 16.09.2005
If a Bluetooth device that is not registered in the list of known devices tries to connect with the handset, you will be prompted on the display to enter the PIN for the Bluetooth device (bonding). u Reject §Go Back§ Press the display key. u Accept ~ Enter the PIN for the Bluetooth device you want to accept and press §OK§. If you have accepted the device, you can use it temporarily (i.e. as long as it is within receiving range or until you deactivate the handset) or save it to the list of known devices. Once the PIN has been confirmed, save to the list of known devices: – Press the display key §Yes§. – Press the display key §No§: use temporarily.
Setting your own area code In order to transfer phone numbers between Bluetooth connections and phone, it is essential that your area code (international and local area code) is stored on the phone. Some of these numbers are already preset. w ¢ Ð ¢ Handset ¢ Area Codes Check that the (pre)set area code is correct. ¤ Change multiple line input: q Select/change input field. r Navigate in the input field. X If necessary, delete number: press the display key. ~ Enter number. §Save§ Press the display key. Example: Area Codes International code:
Changing the Bluetooth name of the handset
00
- 35
0
- [ 814
You can change the handset name used to identify it on the display of another Bluetooth device. w ¢ í ¢ Data Transfer ¢ Bluetooth ¢ Own Device Name §Change§ Press the display key ~ Change name §Save§ Press the display key a Back: Press and hold key.
X
50
Local area code: ]
Save
Restoring the handset to factory settings You can reset any individual settings and changes that you have made. Entries in the directory, the call-by-call list, the call history, the SMS lists and the handset's registration to the base station as well as the content of My stuff are retained. w ¢ Ð ¢ Handset ¢ Reset Handset §Yes§ Press the display key. a Press and hold (idle status).
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / registr_sett.fm / 9.7.07
Base station settings
Base station settings The base station settings are carried out using a registered Gigaset SL37H handset.
Protecting against unauthorised access Protect the system settings of the base station with a PIN known only to yourself. The system PIN must be entered when, for example, registering/de-registering a handset to/from the base station or when restoring the default settings.
Changing the system PIN You can change the 4-digit system PIN set on the base station (default setting: 0000) to a 4-digit PIN known only to yourself. w ¢ Ð ¢ Base ¢ System PIN ~ Enter the current system PIN and press §OK§. ~ Enter new system PIN. For security the PIN is shown as four stars (****). s~ Jump to the next line, re-enter new system PIN and press §OK§. a Press and hold (idle status).
Resetting the system PIN
Version 4, 16.09.2005
If you have forgotten your system PIN you can reset the base station to the original code 0000: Disconnect the power cord from the base station. Hold down the registration/paging key ÷ on the base station while reconnecting the power cable to the base station. Release the key after a time. The base has now been reset and the system PIN 0000 set.
Activating/deactivating music on hold w ¢ Ð ¢ Base ¢ Music on hold Press §OK§ to activate or deactivate music on hold ( ‰ = on).
Repeater support With a repeater you can increase the range and reception strength of your base station. You will need to activate repeater mode. This will terminate any calls that are in progress at the time. Precondition: A repeater is registered. Eco mode is disabled. w ¢ Ð ¢ Base ¢ Add. Features ¢ Repeater Mode §Yes§ Press the display key. When repeater mode is active, the menu item is marked with ‰ .
Please note:
Repeater support and eco mode (see page 12) cancel each other out, i.e. both functions cannot be used at the same time.
Restoring the base station to the factory settings When the settings are restored u eco mode is disabled, u handsets are still registered, u the system PIN is not reset, u the SMS information services are not reset. w ¢ Ð ¢ Base ¢ Base Reset ~ Enter the system PIN and press §OK§. §Yes§ Press the display key. Cancel the restoring process by pressing a or the display key §No§. a Press and hold (idle status). 51
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / pabx.fm / 9.7.07
Connecting the base station to the PABX
Connecting the base station to the PABX The following settings are only necessary when your PABX requires them; see the PABX user guide. You cannot send or receive SMS messages on PABXs that do not support Calling Line Identification.
Dialling modes and recall The current setting is indicated by ‰ .
Setting recall
w ¢ Ð ¢ Base ¢ Add. Features ¢ Recall s Select recall ( ‰ = on) and press §OK§. a Press and hold (idle status).
Version 4, 16.09.2005
Saving an access code (outside line code) Precondition: You may have to enter an access code for external calls in your PABX, e.g. "0". w ¢ Ð ¢ Base ¢ Add. Features ¢ Access Code ~ Enter or change access code, max. 3 digits. ¤ Save changes: (page 59). If an access code has been saved, u The access code is prefixed automatically when you select from the following lists: numbers of the SMS centres, call history or answer machine list. u The access code must be entered when dialling manually and when manually entering directory, emergency/ quick dial numbers and SMS centre numbers.
52
u If you copy recipient's number from the
directory when sending an SMS, you have to delete the access code. u You delete an existing access code with X.
Setting pauses Changing pause after line seizure You can change the length of pause that is inserted between pressing the talk key c and sending the number. w Open menu. N5O L Press keys. ~ Enter digit for the pause length (1 = 1 sec.; 2 = 3 sec.; 3 = 7 sec.) and press §OK§.
Changing the pause after the recall key You can change the length of the pause if your PABX requires this (refer to the user guide for your PABX). w Open menu. N5O 2 Press keys. ~ Enter a digit for the length of the pause (1 = 800 ms; 2 = 1600 ms; 3 = 3200 ms) and press §OK§.
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / pabx.fm / 9.7.07
Connecting the base station to the PABX
Changing a dialling pause (pause after access code) Precondition: You have saved an access code (page 52). w Open menu. N5O
Press keys. ~ Enter a digit for the length of the pause (1 = 1 sec.; 2 = 2 sec.; 3 = 3 sec.; 4 = 6 sec.) and press §OK§. To insert a dialling pause: press S for 2 seconds. A P appears in the display.
Switching temporarily to tone dialling (DTMF)
Version 4, 16.09.2005
If your PABX still operates with pulse dialling (DP), but you need touch tone dialling (DTMF) for a connection (e.g. to listen to the network mailbox) you must switch to touch tone dialling for the call. Precondition: You are conducting a call or have already dialled an external number. * Press the star key. After the call is ended, pulse dialling is automatically switched on again.
53
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / appendix.fm / 9.7.07
Appendix
Appendix
Questions and answers
Care
¤ Wipe the base station, charging cradle
and the handset with a damp cloth (do not use solvent) or an antistatic cloth. Never use a dry cloth. This can cause a build up of static.
Contact with liquid
!
If the handset has come into contact with liquid: 1. Switch off the handset and remove the battery pack immediately. 2. Allow the liquid to drain from the handset. 3. Pat all parts dry, then place the handset with the battery compartment open and the keypad facing down in a dry, warm place for at least 72 hours (not in a microwave, oven etc.). 4. Do not switch on the handset again until it is completely dry. When it has fully dried out, you will normally be able to use it again.
If you have any questions about using your phone, visit us at www.siemens.com/gigasetcustomercare at any time. The table below contains a list of common problems and possible solutions. Registration or connection problems with a Bluetooth headset.
¥ ¥ ¥
Reset the Bluetooth headset (see the user guide for your headset). Delete registration data from the handset when de-registering the device (see page 49). Repeat the registration process (see page 49).
The display is blank. 1. The handset is not switched on. Press and hold the end call key a.
¥
2. The battery pack is flat. Charge/replace the battery pack (page 7).
¥
The keys of a handset do not respond when pressed. The keypad lock is activated. Press and hold the hash key # (page 10).
¥
"Base station x" flashes on the display. 1. The handset is outside the range of the base station. Move the handset closer to the base station.
¥
2. The base station's range is reduced because eco mode is activated. Deactivate eco mode (page 12) or reduce the distance between the handset and the base station.
¥
3. The handset has been de-registered. Register the handset (page 36).
¥
4. The base station is not switched on. Check the base station's mains adapter (page 7).
Version 4, 16.09.2005
¥
54
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / appendix.fm / 9.7.07
Appendix Base Search flashes in the display. The handset is set to Best Base and no base station is switched on or within range. Move the handset closer to the base station. Check the base station's mains adapter (page 7).
You hear an error tone when keying an input (a descending tone sequence).
¥ ¥
Action has failed/invalid input. Repeat the operation. Watch the display and refer to the user guide if necessary.
Handset does not ring.
You cannot listen to messages on the network mailbox.
1. The ringer tone is switched off. Activate the ringer tone (page 44).
¥
2. Call diversion set to All Calls. Switch off call diversion (page 18).
¥
¥
Your phone system is set for pulse dialling. Set your phone system to tone dialling.
¥
You cannot hear a ringer/dialling tone from the fixed network. The phone cord supplied has not been used or has been replaced by a new cord with the wrong jack connections. Please always use the phone cord supplied or ensure that the jack connections are correct when purchasing from a retailer (page 7).
¥
Error tone sounds after system PIN prompt. You have entered the wrong system PIN. Reset the system PIN to 0000 (page 51).
¥
Forgetting the system PIN.
¥
Reset the system PIN to 0000 (page 51).
Call charges are not displayed. 1. Your network provider does not support this feature. 2. There are no metering pulses. Ask your network provider to transmit the metering pulses.
¥
The other party cannot hear you. You have pressed the u (INT) key. The handset is "muted". Switch on the microphone again (page 17).
¥
The number of the caller is not displayed despite CLIP. Calling Line Identification is not enabled. The caller should ask the network provider to release Calling Line Identification (CLI).
Version 4, 16.09.2005
¥
55
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / appendix.fm / 9.7.07
Appendix
Service (Customer Care) You can get assistance easily when you have technical questions or questions about how to use your device by using our online support service on the Internet at: http://www.siemens.com/gigasetcustomercare This site can be accessed at any time wherever you are. It will give you 24/7 support for all our products. It also a list of FAQs and answers plus user guides for you to download. You will also find frequently asked questions and answers in the Questions and Answers section of this user guide in the appendix. If the device needs to be repaired, please contact one of our Customer Care Centers: Abu Dhabi. . . . . . . . . . . . .97 12 62 23 800 Argentina . . . . . . . . . . . . . 0800-888-9878 Australia . . . . . . . . . . . . . . . .1300 665 366 Austria . 05 17 07 50 04 (0,065 Euro/Min.) Bahrain . . . . . . . . . . . . . . .97 31 73 11 173 Belgium . . . . . . . . . . . . . . . . 0 78 15 66 79 Bosnia Herzegovina . . . . . . . . 033 276 649 Brazil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Grande Capitais e Regiões Metropolitanas: . . . . . . . . . . . . . . . . . . . . . . . . . 4003 3020 . . . . . . . . . . . . . . . . . . . . . . . . . (US$ 0,59) Demais localidades: . . . . . 0800 707 1248 . . . . . . . . . . . . . . . . . . . . . . . . . (US$ 0,59) Bulgaria. . . . . . . . . . . . . . . . . 02 873 94 88 Canada . . . . . . . . . . . . . . . . 701-355-3984 China . . . . . . . . . . . . . 0 21 400 670 6007 Croatia . . . . . . . . 016 10 53 81 (0,23 Kun) Czech Republic . . . . . . . . . . . . 233 032 727 Denmark . . . . . . . . . . . . . . . . . 35 25 86 00 Dubai . . . . . . . . . . . . . . . .97 14 39 69 944 Egypt. . . . . . . . . . . . . . . . . . . 202 7623441 Finland . . . . . . . . . . . . . . . . 09 23 11 34 25 France. . . . . . . . . . . . . . . . . 01 56 38 42 00 Germany .01805 333 222 (0,14 Euro/Min.) Greece . . . . . . . . . . . . . . . . .801 1000 500 Hungary . . . . . . . . . 06 14 71 24 44 (27 Ft) Ireland . . . . . . . . . . . . . . . . 18 50 77 72 77 Italy. . . . . . . . . . . . . . . . . . . . 199 15 11 15 Kuwait . . . . . . . . . . . . . . . . 96 52 44 4200 Latvia . . . . . . . . . . . . . . . . . . . . 7 50 11 18 Lebanon . . . . . . Digital Technologies SARL . . . . . . . . . . . . . . . . . . . . . 00961-1240259
Luxembourg . . . . . . . . . . . 40 66 61 56 40 Malaysia. . . . . . . . . . . . . . . .603 77124304 Malta . . . . . . . . . . . . . . +353 21 4940 632 Mexico . . . . . . . . . . . . . .01 80 07 11 00 03 Netherlands . . . . . . . . .0900-3333102 (0,25 Euro/min.) New Zealand . . . . . . . . . . . 08 00 27 43 63 Norway . . . . . . . . . . . . . . . . . . 22 70 84 00 Oman. . . . . . . . . . . . . . . . 96 82 47 09 281 Poland . . . . . . . . . . . . . . . . . 0 801 140 160 Portugal . . . . . . . . . . . . . . . . . . 808781223 Romania . . . . . . . . . . . . . . 02 12 04 60 00 Russia. . . . . . . . . . . . . . . 8 (495) 228 1312 Serbia. . . . . . . . . . . . . . . . . 01 13 07 00 80 Singapore . . . . . . . . . . . . . . . . 62 27 11 18 Slovak Republic . . . . . . . . . . . . . . . . . . . . . . 02 59 68 22 66 Slovenija . . . . . 0 14 74 63 36 (6,30 Tolar) South Africa. . . . . . . . . . . . 08 60 10 11 57 Spain . . . . . . . . . . . . . . . . . . . . 902 103935 Sweden . . . . . . . . . . . . . . . . . 08 750 99 11 Switzerland . . . . . . . . . . 0848 212 000 (0,08 SFr./Min.) Taiwan . . . . . . . . . . . . . . . . 02 23 96 10 06 Thailand. . . . . . . . . . . . . . . . . 02 722 1118 Turkey . . . . . . . . . . . . . . . 0 21 64 59 98 59 Ukraine . . . . . . . . . . . .+380-44-451-71-72 United Arab Emirates . . . . . 0 43 66 03 86 United Kingdom . . . . . . . 0 84 53 67 08 12 USA . . . . . . . . . . . . . . . . . 1-866 247-8758 . . . . . . . . . . . . . . . . . . . . . . . . . . . (toll free)
Version 4, 16.09.2005
Please have your record of purchase ready when calling. Replacement or repair services are not offered in countries where our product is not sold by authorised dealers.
56
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / appendix.fm / 9.7.07
Appendix
Authorisation This device is intended for analogue phone lines in your network. Country-specific requirements have been taken into consideration. We, Siemens Home and Office Communication Devices GmbH & Co. KG, declare that this device meets the essential requirements and other relevant regulations laid down in Directive 1999/5/EC. A copy of the 1999/5/EC Declaration of Conformity is available at this Internet address: http://www.siemens.com/gigasetdocs.
Handset operating times/charging times The operating time of your Gigaset depends on the capacity and the age of the batteries and the way they are used. (All times are maximum possible times and apply when the display backlight is deactivated.) Standby time
approx. 350 hours (15 days)
Talktime
approx. 14 hours
Charging time
approx. 3.5 hours
Base station power consumption In standby mode: approx. 2 watt During the call: approx. 2 watt
General specifications Bluetooth ò Qualified Design Identity The Bluetooth QD ID for your Gigaset SL37H is: B011264.
Specifications Recommended battery pack (Valid at the time of going to press)
Technology: Lithium ion (Li-Ion): Voltage: 3.7 V Capacity: 700 mAh Type: V30145-K1310-X250 V30145-K1310-X322 V30145-K1310-X401 The handset is supplied with the recommended battery pack. Only the original battery pack may be used.
DECT standard
is supported
GAP standard
is supported
No. of channels
60 duplex channels
Radio frequency range
1880–1900 MHz
Duplex method
Time multiplex, 10 ms frame length
Channel grid
1728 kHz
Bit rate
1152 kbit/s
Modulation
GFSK
Language code
32 kbit/s
Transmission power
10 mW, average power per channel
Range
up to 300 m outdoors, up to 50 m indoors
Base station power supply
230 V ~/50 Hz
Version 4, 16.09.2005
Environmental conditions in oper- +5°C to +45°C; ation 20% to 75% humidity
57
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / appendix.fm / 9.7.07
Notes on the user guide
Notes on the user guide This section explains the meaning of certain typographical conventions that are used in this user guide.
Example of a menu input The steps you need to perform are shown in abbreviated form in the user guide. This is illustrated below using the example of "Setting the contrast for the display". The things you have to do are explained in the boxes. w ¢ Ð ¢ Display
¤ When the handset is in idle status,
press the control key in the centre (w) to open the main menu. ¤ With the q control key, select the Ð Settings line. ¤ Press w or press the display key §OK§ to confirm the Settings function. The Settings submenu is displayed. ¤ Press on the bottom of control key q until the Display menu function is selected. ¤ Press w or press the display key §OK§ to confirm the selection. Contrast
Select and press §OK§.
¤ Press on the bottom of control key q ¤
until the Contrast menu function is selected. Press w or press the display key §OK§ to confirm the selection.
r
Select contrast and press w or press the display key §Save§.
¤ Press on the right or left of the control Version 4, 16.09.2005
key to set the contrast.
¤ Press w or press the display key §Save§ to confirm the selection.
58
a
Press and hold (idle status).
¤ Press and hold the end call key until the handset returns to idle status.
Example of multiple line input In many situations you can change settings or enter data in several lines of a display. In this user guide icons are used to guide you step by step through multiple line input. This is illustrated below using the example of "Setting the date and time". The things you have to do are explained in the boxes. You will see the following display (example): Date/Time Date: [15.11.2005] Time: 11:11
Ý
Save
Date: Enter the day, month and year in 8-digit format. The second line is marked with [ ] to show it is active. ¤ Enter the date using the digit keys. Time: Enter hours/minutes in 4-digits format.
¤ Press the s key.
The fourth line is marked with [ ] to show it is active. ¤ Enter the date using the digit keys.
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / appendix.fm / 9.7.07
Notes on the user guide
¤ Save the changes. ¤ Pressing the display key §Save§. ¤ Then press and hold the a key.
When you press and hold a key, the characters of that key appear in the display and are highlighted one after the other. When you release the key, the highlighted character is inserted into the input field.
The handset switches to idle status.
Setting upper/lower case or digits
Writing and editing text The following rules apply when writing a text: u Control the cursor with u v t s. u Characters are inserted on the left of the cursor. u Press the star key * to show the table of special characters. u The first letter of the name of directory entries is automatically capitalised, followed by lower case letters. You can call up the table of special characters when writing an SMS using the * key. Select the required character and insert it with §Insert§.
Writing an SMS/name (without predictive text) Press the relevant key several times to enter letters/characters.
Version 4, 16.09.2005
1)
2a 3 d 4 g 5 j L m M p N t O w Q .
2x 2)
b e h k n q u x ,
Writing SMS (with predictive text) EATONI predictive text helps you when you are writing SMS messages. Each key between Q and O is assigned several letters and characters. These appear in a selection line immediately under the text panel (over the display keys) as soon as you press a key. The letter you are most likely looking for is shown in reversed highlights and is at the beginning of the selection line. It is copied into the text panel. SMS 572(1) Hello Peter, I cannot come today. W
Standard characters 1x
Press the hash key # briefly to switch from "Abc" mode to "123" and from "123" to "abc" and from "abc" to "Abc" (upper case: 1st letter upper case, all others lower case). Press the hash key # before entering the letter. You can see in the display whether upper case, lower case or digits is selected.
3x
4x
5x
6x
7x
8x
9x 10x
1 c f i l o r v y ?
2 3 4 5 6 s 8 z !
ä ë ï
á é í
à è ì
â ê î
ã
ö 7 ü 9 0
ñ ß ú ÿ
ó
ò
ô
õ
ù ý
û æ
ø
å
ç
hgi
X
Ç Abc
Options
1 2 3 4 5
1 Remaining number of characters, in brackets: SMS part 1-n 2 SMS text 3 Selection line 4 EATONI is activated 5 Upper/lower case or digits
1) Space 2) Line break
59
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / appendix.fm / 9.7.07
Additional functions via the PC interface If this letter is the one you want, confirm it by pressing the next key. If it does not match the one you want, press the hash key # briefly until the letter you are looking for is reverse highlighted in the display line and then transferred to the text field. If you press and hold the hash key # you switch from "Abc" mode to "123" and from "123" to "abc" and from "abc" to "Abc".
Activating/deactivating predictive text Precondition: you are writing an SMS message. §Options§ Press the display key. Predictive Text Select and press §OK§ ( ‰ = on). a Press the end call key briefly to return to the text field. Enter the text.
Additional functions via the PC interface You can connect the handset to your computer via Bluetooth (page 48) or by using a data cable (page 62). If you want to use the Bluetooth connection, your computer must be equipped with a suitable dongle. Your handset can communicate with the computer using the "Gigaset QuickSync" program (free download at www.siemens.com/gigasetSL370). You can u access your handset's directory and synchronise it with Outlook, or copy contact details to the handset, u download CLIP pictures (.bmp) from the computer to the handset, u download pictures (.bmp) for the screensaver from the computer to the handset. During the transfer of data between handset and PC, you will see ß on the display. During this time the keypad is disabled, and incoming calls will be ignored.
Please note:
Version 4, 16.09.2005
– If Bluetooth is activated and accessories (e.g data cables page 60) are plugged into the connection socket (page 1), Bluetooth is automatically deactivated. – If a Bluetooth voice connection has already been established, Bluetooth is not deactivated until it is ended. – If a Bluetooth data connection has already been established, the response depends on the receiving device. – Bluetooth is automatically reactivated when the accessories are removed. – If Bluetooth is deactivated and accessories are plugged in, then Bluetooth cannot be activated.
60
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / accessories_SAG.fm / 9.7.07
Accessories
Accessories Gigaset Handsets Upgrade your Gigaset to a cordless PABX:
Gigaset Handset SL37H u u u u u u u u
Illuminated graphical colour display (65 k colours) Illuminated keypad Handsfree talking Polyphonic ringer tones Directory for around 250 entries Picture CLIP SMS (precondition: CLIP must be enabled) PC interface. e.g. for managing directory entries, ringer tones and screensavers u Headset socket u Bluetooth u Room monitor u Walky-talky function www.siemens.com/gigasetSL37H
Gigaset Handset SL56 u u u u u u u u u
Version 4, 16.09.2005
Illuminated graphical colour display (65 k colours) Illuminated keypad Handsfree talking Polyphonic ringer tones Directory for around 250 entries Picture CLIP SMS (precondition: CLIP must be enabled) Voice dialling PC interface. e.g. for managing directory entries, ringer tones and screensavers u Headset socket u Bluetooth www.siemens.com/gigasetSL56
61
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / accessories_SAG.fm / 9.7.07
Accessories
Gigaset Handset S45 u u u u u u u u
Illuminated colour display (4096 colours) Illuminated keypad Handsfree talking Polyphonic ringer tones Directory for around 150 entries SMS (precondition: CLIP must be enabled) Headset socket Room monitor www.siemens.com/gigasetS45
Gigaset Handset E45 u u u u u u u u u
Dust and splash proof casing Illuminated colour display (4096 colours) Illuminated keypad Handsfree talking Polyphonic ringer tones Directory for around 150 entries SMS (precondition: CLIP must be enabled) Headset socket Room monitor www.siemens.com/gigasete45
Gigaset repeater The Gigaset repeater can be used to increase the reception range of your Gigaset handset to the base station. www.siemens.com/gigasetrepeater
Mobile handsfree set with PTT key
Version 4, 16.09.2005
With the mobile handsfree set you can make a call while keeping your hands free. In addition, conversations can be heard on the handset.
Data Cable USB DCA-510 For connecting your phone to the USB interface of your computer. 62
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / accessories_SAG.fm / 9.7.07
Wall-mounting the base station
Gigaset HC450 – intercom system for cordless phones u Use the intercom from your cordless phone – no need for
a fixed home phone
u Intuitive user functions using the softkeys (open door,
switch on entry light) Simple to configure using the handset menu Forward to outside phone numbers (intercom feature) Simple to install and register with the Gigaset system Replaces existing call button – no further cable is needed Supports the existing gong and standard door opener Configuration options for the second ringer key (separate intercom call, activating interior lighting, or function such as first ringer key) www.siemens.com/GigasetHC450 u u u u u u
All accessories and battery packs are available from your mobile phone retailer. Only use original accessories. This will avoid possible health risks and damage to property, and also ensure that all the relevant regulations are complied with.
Wall-mounting the base station 100 mm
Version 4, 16.09.2005
approx. 9 mm
63
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / SL370SIX.fm / 9.7.07
Index
Index A Access code for a PABX . . . . . . . . . . . . . . . . . . . 52 Access protection . . . . . . . . . . . . . . . . 51 Accessories . . . . . . . . . . . . . . . . . . . . 61 Activating advisory tones . . . . . . . . . . . . . . . . 46 appointment . . . . . . . . . . . . . . . . . 47 Bluetooth mode . . . . . . . . . . . . . . . 48 call acceptance . . . . . . . . . . . . . . . . 43 handset . . . . . . . . . . . . . . . . . . . . . 10 internal listening in . . . . . . . . . . . . . 38 keypad lock . . . . . . . . . . . . . . . . . . 10 room monitor . . . . . . . . . . . . . . 39, 40 Advisory tones . . . . . . . . . . . . . . . . . . 46 Alarm clock . . . . . . . . . . . . . . . . . . . . 46 Alert tone . . . . . . . . . . . . . . . . . . . . . 44 Anniversary . . . . . . . . . . . . . . . . . . . . 23 deactivating . . . . . . . . . . . . . . . . . . 23 missed . . . . . . . . . . . . . . . . . . . 23, 48 saving in directory . . . . . . . . . . . . . 23 Appointment . . . . . . . . . . . . . . . . . . . 47 Appointment/anniversary display missed . . . . . . . . . . . . . . . . 48 Appointments activating/deactivating . . . . . . . . . . 47 deleting . . . . . . . . . . . . . . . . . . . . . 47 managing. . . . . . . . . . . . . . . . . . . . 47 Area code setting own dialling code . . . . . . . . 50 Assigning a key . . . . . . . . . . . . . . . . . 41 Assigning numerical keys . . . . . . . . . . 41 Authorisation . . . . . . . . . . . . . . . . . . . 57 Automatic call acceptance . . . . . . . . . . . . . 16, 43 last number redial . . . . . . . . . . . . . . 24 network provider preselection . . . . . 25
Version 4, 16.09.2005
B Base station changing . . . . . . . . . . . . . . . . . . . . 37 connecting . . . . . . . . . . . . . . . . . . . . 7 connecting and installing . . . . . . . . . 6 connecting to PABX. . . . . . . . . . . . . 52 range . . . . . . . . . . . . . . . . . . . . . . . . 7 restoring factory settings . . . . . . . . 51 64
setting . . . . . . . . . . . . . . . . . . . . . 51 system PIN . . . . . . . . . . . . . . . . . . 51 Battery pack charging . . . . . . . . . . . . . . . . . . . 1, 9 display . . . . . . . . . . . . . . . . . . . . 1, 9 icon . . . . . . . . . . . . . . . . . . . . . . 1, 9 inserting . . . . . . . . . . . . . . . . . . . . . 7 recommended battery pack . . . . . . 57 tone . . . . . . . . . . . . . . . . . . . . . . . 46 Beep, see Advisory tones Best base station . . . . . . . . . . . . . . . . 37 Birthday, see Anniversary Bluetooth answering a call . . . . . . . . . . . . . . . 16 changing device name . . . . . . . 49, 50 de-registering devices . . . . . . . . . . 49 list of known devices . . . . . . . . . . . 49 registering devices . . . . . . . . . . . . . 49 transferring directory (vCard) . . . . . 22 Bluetooth connection setting own area code . . . . . . . . . . 50
C Calendar . . . . . . . . . . . . . . . . . . . . . . 47 Call acceptance . . . . . . . . . . . . . . . . . . 43 accepting . . . . . . . . . . . . . . . . . . . 16 answering (Bluetooth) . . . . . . . . . . 16 disconnecting (toggling) . . . . . . . . 18 diverting . . . . . . . . . . . . . . . . . . . . 18 duration . . . . . . . . . . . . . . . . . . . . 16 ending . . . . . . . . . . . . . . . . . . . . . 16 external . . . . . . . . . . . . . . . . . . . . . 16 history . . . . . . . . . . . . . . . . . . . . . 24 internal . . . . . . . . . . . . . . . . . . . . . 37 party listening in . . . . . . . . . . . . . . 38 transferring (connect) . . . . . . . 37, 38 Call waiting accepting/rejecting . . . . . . . . . . . . 18 activating/deactivating . . . . . . . . . . 18 internal call . . . . . . . . . . . . . . . . . . 38 Callback . . . . . . . . . . . . . . . . . . . . . . 18 Call-by-call . . . . . . . . . . . . . . . . . . . . 20 numbers . . . . . . . . . . . . . . . . . 20, 25 Call-by-call list key . . . . . . . . . . . . . . . . . . . . . . . . . 1 Calling external . . . . . . . . . . . . . . . . . . . . . 16 Calling Line Identification . . . . . . . . . 16
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / SL370SIX.fm / 9.7.07
Index Care of the telephone . . . . . . . . . . . . 54 CF (Call Forwarding) . . . . . . . . . . . . . 18 Changing destination number . . . . . . . . . . . . 39 device name (Bluetooth) . . . . . . 49, 50 dialling mode . . . . . . . . . . . . . . . . . 52 display language . . . . . . . . . . . . . . . 42 earpiece volume . . . . . . . . . . . . . . . 43 handsfree volume . . . . . . . . . . . . . . 43 internal number of a handset . . . . . 38 name of a handset . . . . . . . . . . . . . 38 pause time . . . . . . . . . . . . . . . . . . . 52 ringer tone . . . . . . . . . . . . . . . . . . . 43 system PIN . . . . . . . . . . . . . . . . . . . 51 Character set . . . . . . . . . . . . . . . . 28, 30 Charge status display . . . . . . . . . . . . 1, 9 CLI, CLIP . . . . . . . . . . . . . . . . . . . . . . 16 CLIP picture . . . . . . . . . . . . . . 17, 20, 45 Conference . . . . . . . . . . . . . . . . . . . . 18 Conference call (internal) . . . . . . . . . . 37 Configuring the network mailbox . . . . 35 Confirmation tone . . . . . . . . . . . . . . . 46 Connecting, base station to PABX . . . . 52 Consultation . . . . . . . . . . . . . . . . . . . 18 Consultation call (internal) . . . . . . . . . 37 Control key . . . . . . . . . . . . . . . . . . 1, 10 Correcting incorrect entries . . . . . . . . 11 Customer Care . . . . . . . . . . . . . . . . . . 56
Version 4, 16.09.2005
D Deactivating advisory tones . . . . . . . . . . . . . . . . 46 appointment . . . . . . . . . . . . . . . . . 47 appointment reminder . . . . . . . . . . 47 call acceptance . . . . . . . . . . . . . . . . 43 handset . . . . . . . . . . . . . . . . . . . . . 10 internal listening in . . . . . . . . . . . . . 38 keypad lock . . . . . . . . . . . . . . . . . . 10 preselection . . . . . . . . . . . . . . . . . . 26 room monitor . . . . . . . . . . . . . . . . . 40 Delete key . . . . . . . . . . . . . . . . . . . . . 10 Deleting characters . . . . . . . . . . . . . . . . . . . 11 De-registering (handset). . . . . . . . . . . 36 De-registering devices (Bluetooth) . . . 49 Destination number (room monitor) . . . . . . . . . . . 39, 40
Dialling call-by-call list . . . . . . . . . . . . . . . . 21 directory . . . . . . . . . . . . . . . . . . . . 21 quick dial . . . . . . . . . . . . . . . . . . . . 41 with quick dial . . . . . . . . . . . . . . . . 22 Dialling pause . . . . . . . . . . . . . . . . . . 53 entering . . . . . . . . . . . . . . . . . . . . . 1 Directory . . . . . . . . . . . . . . . . . . . . . 20 copying number from text . . . . . . . 22 managing entries. . . . . . . . . . . . . . 21 opening . . . . . . . . . . . . . . . . . . . . 10 order of entries . . . . . . . . . . . . . . . 21 save anniversary . . . . . . . . . . . . . . 23 saving entry . . . . . . . . . . . . . . . . . 20 sending entry/list to handset . . . . . 22 storing the sender’s number (SMS) . . . . . . . . . . . . . . . . . . . 30 transferring a vCard (Bluetooth) . . . 22 using to enter numbers . . . . . . . . . 22 Disconnecting waiting caller (toggle) . 18 Display backlight . . . . . . . . . . . . . . . . . . . . 43 changing display language . . . . . . . 42 contrast. . . . . . . . . . . . . . . . . . . . . 42 in idle status . . . . . . . . . . . . . . . . . 11 memory (directory/call-by-call) . . . . 21 memory (My stuff) . . . . . . . . . . . . 45 missed appointments/ anniversaries . . . . . . . . . . . . . . 48 network mailbox report . . . . . . . . . 35 number (CLI/CLIP) . . . . . . . . . . . . . 16 screensaver . . . . . . . . . . . . . . . . . . 42 setting . . . . . . . . . . . . . . . . . . . . . 42 wrong language . . . . . . . . . . . . . . 42 Display keys . . . . . . . . . . . . . . . . . 1, 10 assigning . . . . . . . . . . . . . . . . . . . . 41 Draft message list (SMS) . . . . . . . . . . 28
E Earpiece mode . . . . . . . . . . . . . . . . . 17 Earpiece volume . . . . . . . . . . . . . . . . 43 EATONI (predictive text) . . . . . . . . . . 59 ECO DECT . . . . . . . . . . . . . . . . . . . . . 12 Eco mode . . . . . . . . . . . . . . . . . . . . . 12 E-mail address. . . . . . . . . . . . . . . . . . 29 copying from the directory . . . . . . . 22 End call key. . . . . . . . . . . . . . . . . . 1, 16
65
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / SL370SIX.fm / 9.7.07
Index Ending, call . . . . . . . . . . . . . . . . . . . . 16 Ending, see deactivate Entry saving (network mailbox) . . . . . . . . 35 saving, changing (preselection) . . . . 26 selecting (menu) . . . . . . . . . . . . . . 58 selecting from directory . . . . . . . . . 21 Error tone . . . . . . . . . . . . . . . . . . . . . 46 Example menu input . . . . . . . . . . . . . . . . . . 58 multiple line input . . . . . . . . . . . . . 58
using room monitor . . . . . . . . . . . . 39 using several . . . . . . . . . . . . . . . . . 36 Handset operating time in room monitor mode . . . . . . . . . . 39 Handsfree key . . . . . . . . . . . . . . . . . . . 1 Handsfree talking . . . . . . . . . . . . . . . 17 Handsfree volume . . . . . . . . . . . . . . . 43 Hash key . . . . . . . . . . . . . . . . . . . . 1, 10 Hearing aids . . . . . . . . . . . . . . . . . . . . 4 Hold music . . . . . . . . . . . . . . . . . 17, 51 setting . . . . . . . . . . . . . . . . . . . . . 51
F
I
Fast access network mailbox . . . . . . . . . . . . . . . 35 Flash time . . . . . . . . . . . . . . . . . . . . . 52
Icon alarm clock . . . . . . . . . . . . . . . . . . 46 battery pack . . . . . . . . . . . . . . . . . . 9 display . . . . . . . . . . . . . . . . . . . . . 10 for new messages . . . . . . . . . . . . . 24 keypad lock . . . . . . . . . . . . . . . . . . 10 new SMS . . . . . . . . . . . . . . . . . . . . 29 ringer tone . . . . . . . . . . . . . . . . . . 44 Idle status (display) . . . . . . . . . . . . . . 11 Idle status, returning to . . . . . . . . . . . 11 Incoming message list (SMS) . . . . . . . 29 Incorrect input (correction) . . . . . . . . 11 Information services (SMS) . . . . . . . . 33 Input language (SMS) . . . . . . . . . . . . 28 Installation, base station . . . . . . . . . . . 6 Internal conference . . . . . . . . . . . . . . . . . . 37 consulting . . . . . . . . . . . . . . . . . . . 37 listening in . . . . . . . . . . . . . . . . . . 38 making calls . . . . . . . . . . . . . . . . . 37 Internal call. . . . . . . . . . . . . . . . . . . . 37 call waiting . . . . . . . . . . . . . . . . . . 38
G Group call . . . . . . . . . . . . . . . . . . . . . 37
Version 4, 16.09.2005
H Handset activating/deactivating . . . . . . . . . . 10 advisory tones . . . . . . . . . . . . . . . . 46 changing internal number . . . . . . . . 38 changing name . . . . . . . . . . . . . . . 38 changing the number . . . . . . . . . . . 38 changing to a different base station . . . . . . . . . . . . . . . . . . . 37 changing to best reception . . . . . . . 37 contact with liquid . . . . . . . . . . . . . 54 de-registering . . . . . . . . . . . . . . . . . 36 display backlight . . . . . . . . . . . . . . . 43 display language . . . . . . . . . . . . . . . 42 earpiece volume . . . . . . . . . . . . . . . 43 handsfree volume . . . . . . . . . . . . . . 43 idle status . . . . . . . . . . . . . . . . . . . 11 list . . . . . . . . . . . . . . . . . . . . . . . . . 10 locating . . . . . . . . . . . . . . . . . . . . . 36 muting . . . . . . . . . . . . . . . . . . . . . . 17 paging . . . . . . . . . . . . . . . . . . . . . . 36 registering . . . . . . . . . . . . . . . . . . . 36 registering to a different base station . . . . . . . . . . . . . . . . . . . 37 restoring to factory settings. . . . . . . 50 screensaver . . . . . . . . . . . . . . . . . . 42 setting . . . . . . . . . . . . . . . . . . . . . . 41 setting up . . . . . . . . . . . . . . . . . . . . . 7 signal strength . . . . . . . . . . . . . . . . . 7 transferring a call . . . . . . . . . . . . . . 37 66
K Key 1 (fast access) . . . . . . . . . . . . . . . . 1 Keypad lock . . . . . . . . . . . . . . . . . . . 10 Keys call-by-call list . . . . . . . . . . . . . . . . . 1 control key . . . . . . . . . . . . . . . . 1, 10 delete key . . . . . . . . . . . . . . . . . . . 10 display keys . . . . . . . . . . . . . . . . 1, 10 end call key . . . . . . . . . . . . . . . . 1, 16 fast access . . . . . . . . . . . . . . . . . . . . 1 handsfree key . . . . . . . . . . . . . . . . . 1 hash key . . . . . . . . . . . . . . . . . . 1, 10 message key . . . . . . . . . . . . . . . . . . 1
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / SL370SIX.fm / 9.7.07
Index on/off key . . . . . . . . . . . . . . . . . . . . . 1 quick dial . . . . . . . . . . . . . . . . . . . . 22 recall key . . . . . . . . . . . . . . . . . . . . . 1 star key . . . . . . . . . . . . . . . . . . . . . . 1 talk key . . . . . . . . . . . . . . . . . . . 1, 16
L Language, display . . . . . . . . . . . . . . . 42 Last number redial . . . . . . . . . . . . . . . 23 Linking, see SMS Liquid . . . . . . . . . . . . . . . . . . . . . . . . 54 List . . . . . . . . . . . . . . . . . . . . . . . . . . 20 call history . . . . . . . . . . . . . . . . . . . 24 call-by-call list . . . . . . . . . . . . . . . . . 20 handsets . . . . . . . . . . . . . . . . . . . . 10 known devices (Bluetooth) . . . . . . . 49 missed calls . . . . . . . . . . . . . . . . . . 25 network mailbox . . . . . . . . . . . . . . . 24 SMS draft message list . . . . . . . . . . 28 SMS incoming message list . . . . . . . 29 SMS list . . . . . . . . . . . . . . . . . . . . . 24 Listening in to call . . . . . . . . . . . . . . . 38 Locating, handset . . . . . . . . . . . . . . . 36 Lock activating/deactivating keypad protection . . . . . . . . . . . . . . . . 10
Version 4, 16.09.2005
M Mailbox ID, see SMS Mailboxes, see SMS Mains adapter . . . . . . . . . . . . . . . . . . . 4 Making calls accepting a call . . . . . . . . . . . . . . . . 16 external . . . . . . . . . . . . . . . . . . . . . 16 internal . . . . . . . . . . . . . . . . . . . . . 37 Making cost-effective calls . . . . . . . . . 25 Manual last number redial . . . . . . . . . 23 Medical appliances . . . . . . . . . . . . . . . . 4 Memory directory/call-by-call . . . . . . . . . . . . 21 My stuff . . . . . . . . . . . . . . . . . . . . . 45 Menu end tone . . . . . . . . . . . . . . . . . . . . 46 menu guidance . . . . . . . . . . . . . . . 11 menu input . . . . . . . . . . . . . . . . . . 58 opening . . . . . . . . . . . . . . . . . . . . . 10 overview . . . . . . . . . . . . . . . . . . . . 13 Message key . . . . . . . . . . . . . . . . . . . . 1 open list . . . . . . . . . . . . . . . . . . . . . 29 opening lists . . . . . . . . . . . . . . . . . . 24
Microphone . . . . . . . . . . . . . . . . . . . . 1 Missed anniversary . . . . . . . . . . . . . . . . . . 48 appointment . . . . . . . . . . . . . . . . . 48 calls . . . . . . . . . . . . . . . . . . . . . . . 25 Multiple line input . . . . . . . . . . . . . . . 58 Muting the handset. . . . . . . . . . . . . . 17 My stuff . . . . . . . . . . . . . . . . . . . . . . 45
N Name of a handset . . . . . . . . . . . . . . . . . 38 Network provider (numbers list) . . . . 20 Network provider preselection, automatic . . . . . . . . . . . . . . . . . 25 Network services. . . . . . . . . . . . . . . . 18 Notification by SMS . . . . . . . . . . . . . . 31 Number as destination for room monitor . . . . . . . . . . . . . . 39, 40 copying from an SMS text . . . . . . . 30 copying from directory . . . . . . . . . . 22 copying to directory . . . . . . . . . . . . 22 displaying caller's number (CLIP) . . . 16 entering network mailbox number . 35 entering with directory. . . . . . . . . . 22 saving in the directory . . . . . . . . . . 20 Numbers list network provider . . . . . . . . . . . . . . 20
O On/Off key . . . . . . . . . . . . . . . . . . . . . 1 Order in directory . . . . . . . . . . . . . . . 21 Outside line code . . . . . . . . . . . . . . . 52
P PABX connecting base station . . . . . . . . . 52 pauses . . . . . . . . . . . . . . . . . . . . . 52 saving access code . . . . . . . . . . . . . 52 setting dialling mode . . . . . . . . . . . 52 setting recall . . . . . . . . . . . . . . . . . 52 SMS . . . . . . . . . . . . . . . . . . . . . . . 33 switch to touch tone dialling . . . . . 53 Pack contents . . . . . . . . . . . . . . . . . . . 6 Paging . . . . . . . . . . . . . . . . . . . . . . . 36 Paging key . . . . . . . . . . . . . . . . . . . . . 1 Pause . . . . . . . . . . . . . . . . . . . . . 52, 53 PC interface . . . . . . . . . . . . . . . . . . . 60 Phone jack assignment . . . . . . . . . . . . 7 67
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / SL370SIX.fm / 9.7.07
Index Picture deleting . . . . . . . . . . . . . . . . . . . . . 45 renaming . . . . . . . . . . . . . . . . . . . . 45 PIN change system PIN . . . . . . . . . . . . . . . . . . . 51 Power consumption . . . . . . . . . . . . . . 57 Predictive text . . . . . . . . . . . . . . . . . . 59 Preselection . . . . . . . . . . . . . . . . . . . . 25 deactivating . . . . . . . . . . . . . . . . . . 26 Protecting the phone against access . . 51
Q Questions and answers . . . . . . . . . . . 54 Quick dial . . . . . . . . . . . . . . . . . . 20, 41
R Range . . . . . . . . . . . . . . . . . . . . . . . . . 7 Recall . . . . . . . . . . . . . . . . . . . . . . . . 52 Recall key . . . . . . . . . . . . . . . . . . . . . . 1 pause after . . . . . . . . . . . . . . . . . . . 52 Reception booster, see Repeater Registering (handset) . . . . . . . . . . . . . 36 Registering devices (Bluetooth). . . . . . 49 Registration key . . . . . . . . . . . . . . . . . . 1 Reminder call . . . . . . . . . . . . . . . . . . . 23 Repeater . . . . . . . . . . . . . . . . . . . . . . 51 Ringer tone changing . . . . . . . . . . . . . . . . . . . . 43 setting volume . . . . . . . . . . . . . . . . 43 Room monitor . . . . . . . . . . . . . . . . . . 39
Version 4, 16.09.2005
S Saving (access code) . . . . . . . . . . . . . 52 Screensaver . . . . . . . . . . . . . . . . . . . . 42 Searching in directory . . . . . . . . . . . . 21 Sending directory entry to handset . . . . . . . . 22 Sensitivity (room monitor) . . . . . . 39, 40 Service . . . . . . . . . . . . . . . . . . . . . . . 56 Setting date . . . . . . . . . . . . . . . . . . . . . . . . . 9 screensaver . . . . . . . . . . . . . . . . . . 42 time . . . . . . . . . . . . . . . . . . . . . . . . . 9 Setting up handset . . . . . . . . . . . . . . . . . . . . . . 7 Shortcut . . . . . . . . . . . . . . . . . . . . . . 13 Signal strength . . . . . . . . . . . . . . . . . . 7 Silent alert . . . . . . . . . . . . . . . . . . . . . 44 SIM card setting own area code . . . . . . . . . . . 50 68
SMS . . . . . . . . . . . . . . . . . . . . . . . . . 27 active send service centre . . . . . . . 27 changing mailbox . . . . . . . . . . . . . 32 deleting. . . . . . . . . . . . . . . . . . . . . 28 draft message list . . . . . . . . . . . . . 28 forwarding . . . . . . . . . . . . . . . . . . 30 incoming message list . . . . . . . . . . 29 information services . . . . . . . . . . . 33 input language . . . . . . . . . . . . . . . 28 linked . . . . . . . . . . . . . . . . . . . . . . 27 list . . . . . . . . . . . . . . . . . . . . . . . . 24 mailbox ID . . . . . . . . . . . . . . . . . . . 31 mailboxes . . . . . . . . . . . . . . . . . . . 31 notification by SMS . . . . . . . . . . . . 31 notification number . . . . . . . . . . . . 31 notification type . . . . . . . . . . . . . . 31 PIN protection . . . . . . . . . . . . . . . . 31 reading . . . . . . . . . . . . . . . . . . . . . 28 receiving . . . . . . . . . . . . . . . . . . . . 29 replying to and forwarding . . . . . . . 30 rules . . . . . . . . . . . . . . . . . . . . . . . 27 saving number. . . . . . . . . . . . . . . . 30 self help with error messages . . . . . 34 sending to a personal mailbox . . . . 32 sending to an e-mail address . . . . . 29 status report . . . . . . . . . . . . . . . . . 28 to a PABX. . . . . . . . . . . . . . . . . . . . 33 troubleshooting . . . . . . . . . . . . . . . 34 writing . . . . . . . . . . . . . . . . . . . . . 27 SMS centre changing number . . . . . . . . . . . . . 32 setting . . . . . . . . . . . . . . . . . . . . . 32 Snooze mode . . . . . . . . . . . . . . . . . . 46 Sound, see Ringer tone Special functions . . . . . . . . . . . . . . . . 52 Specifications . . . . . . . . . . . . . . . . . . 57 Star key . . . . . . . . . . . . . . . . . . . . . . . 1 System settings . . . . . . . . . . . . . . . . . 51
T Talk key . . . . . . . . . . . . . . . . . . . . 1, 16 Text message, see SMS Toggling . . . . . . . . . . . . . . . . . . . . . . 18 Touch tone dialling . . . . . . . . . . . 52, 53 Troubleshooting . . . . . . . . . . . . . . . . 54 Troubleshooting (SMS) . . . . . . . . . . . 34
U Unknown . . . . . . . . . . . . . . . . . . . . . 17 Unknown caller . . . . . . . . . . . . . . . . . 17
Gigaset SL370 / IM-Nord English / A31008-M1903-R201-2-SM19 / SL370SIX.fm / 9.7.07
Index
V Viewing the network mailbox report . . 35 VIP (directory entry) . . . . . . . . . . . . . . 21 Volume earpiece . . . . . . . . . . . . . . . . . . . . . 43 earpiece volume . . . . . . . . . . . . . . . 43 handset handsfree volume . . . . . . . 43 loudspeaker . . . . . . . . . . . . . . . . . . 43 ringer tone . . . . . . . . . . . . . . . . . . . 43 setting . . . . . . . . . . . . . . . . . . . . . . 44
W
Version 4, 16.09.2005
Warning tone, see Advisory tones Writing (SMS) . . . . . . . . . . . . . . . . . . 27 Writing, editing text . . . . . . . . . . . . . . 59
69
