Transcript
19-1092; Rev 1; 9/99
KIT ATION EVALU E L B A AVAIL
1-Input/6-Output Video Distribution Amplifiers
The MAX4135 achieves a -3dB bandwidth of 185MHz, with 0.1dB gain flatness to 40MHz. The MAX4136’s -3dB bandwidth is 140MHz. Both devices deliver a 1000V/µs slew rate, as well as exceptional full-power bandwidths of 185MHz and 140MHz, respectively. A 25ns channel switching time enables rapid multiplexing for picture-in-picture applications, yet maintains a high off-isolation of 75dB and all-hostile crosstalk of -50dB (f = 30MHz). The MAX4135/MAX4136’s on-board logic selects any combination of the six signal outputs. Each output is capable of swinging ±2V and delivering 65mA. For applications that require a 1-input/4-output distribution amplifier, see the MAX4137/MAX4138 data sheet.
_____________________Selector Guide PART
NO. OF OUTPUTS
GAIN (V/V)
-3dB BANDWIDTH (MHz)
MAX4135
6
Fixed 2
185
MAX4136
6
≥2
140
MAX4137
4
Fixed 2
185
MAX4138
4
≥2
140
________________________Applications Video Switching and Distribution High-Resolution RGB CRT Monitors
____________________________Features ♦ Fixed Gain of 2V/V (MAX4135) External Gain Set (MAX4136) ♦ High Speed: 185MHz -3dB Bandwidth (MAX4135) 140MHz -3dB Bandwidth (MAX4136) 1000V/µs Slew Rate ♦ High Full-Power Bandwidths (VOUT = 2VP-P): 185MHz (MAX4135) 140MHz (MAX4136) ♦ 0.1dB Gain Flatness to 40MHz ♦ Low Differential Gain/Phase Error: 0.10%/0.02° ♦ High-Impedance Output Disable
______________Ordering Information PART
TEMP RANGE
PIN-PACKAGE
MAX4135EWG
-40°C to +85°C
24 Wide SO
MAX4136EWG
-40°C to +85°C
24 Wide SO
Pin Configuration TOP VIEW OUT1 1
24 SEL1
VCCO 2
23 SEL2
OUT2 3
22 SEL3
AGND 4
21 AGND
OUT3 5
MAX4135 MAX4136
20 IN+
High-Speed Analog Bus Drivers
VEEO 6
RF Signal Processing
VEEO 7
18 AGND (RG)
Composite Video Preamplifiers
OUT4 8
17 N.C. (RF)
AGND 9
16 VCCI
OUT5 10
15 SEL4
19 VEEI
VCCO 11
14 SEL5
OUT6 12
13 SEL6
SO ( ) ARE FOR MAX4136.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX4135/MAX4136
_______________General Description The MAX4135/MAX4136 are 1-input/6-output voltagefeedback amplifiers that combine high speed with fast switching for video distribution applications. The MAX4135 is internally set for a closed-loop gain of 2V/V, while the MAX4136 can be externally set for gains of 2V/V or greater.
MAX4135/MAX4136
1-Input/6-Output Video Distribution Amplifiers ABSOLUTE MAXIMUM RATINGS Power-Supply Voltage (VCC to VEE).......................................12V Voltage on Any Input Pin to GND .......(VCC + 0.3V) to (VEE - 0.3V) Short-Circuit Duration to GND....................................Continuous Continuous Power Dissipation (TA = +70°C) 24-Pin Wide SO (derate 19.3mW/°C above +70°C) ......1.54W
Operating Temperature Range MAX4135EWG/MAX4136EWG ........................-40°C to +85°C Storage Temperature Range .............................-65°C to +160°C Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS (VCC = 5V, VEE = -5V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER Input Offset Voltage
SYMBOL VOS
Input Offset Voltage Match Between Channels Input Offset Voltage Drift Input Bias Current
TCVOS IB
TYP
MAX
UNITS
VOUT = 0, RL = ∞
CONDITIONS
MIN
1
10
mV
VOUT = 0, RL = ∞
1
8
mV
VOUT = 0, RL = 150Ω
30
VOUT = 0, RL = 150Ω, VCM = 0
4.5
µV/°C 13
µA
Common-Mode Input Resistance
RIN(CM)
MAX4136, either input
5
MΩ
Common-Mode Input Capacitance
CIN(CM)
MAX4136, either input
2
pF
7 88 2.4 30 2
nV/√Hz µVRMS pA/√Hz nARMS pF
±2.5
V
60 65 45 70 2.6 -2.5 65
dB dB
Input Voltage Noise
en
Input Current Noise
in
Input Capacitance
CIN
Common-Mode Input Voltage Range
VCM
Common-Mode Rejection Ratio Power-Supply Rejection Ratio Quiescent Supply Current
CMRR PSRR ISY
f = 1MHz f = 1MHz to 100MHz f = 1MHz f = 1MHz to 100MHz
MAX4136 MAX4136, VCM = ±2.5V VS = ±4.75V to ±5.25V VIN = 0
Output Voltage Swing
VOUT
RL = 150Ω
Output Current Drive SEL High Threshold SEL Low Threshold SEL Input Current
IOUT VIH VIL ISEL
RL = 30Ω
2
55 all channels off all channels on positive negative
2.2 -2.0 45
65 90
V
2.0 0.8 1
_______________________________________________________________________________________
mA
5
mA V V µA
1-Input/6-Output Video Distribution Amplifiers (VCC = 5V, VEE = -5V, AVCL = 2V/V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER -3dB Bandwidth
SYMBOL BW-3dB
Full-Power Bandwidth
FPBW
0.1dB Bandwidth
CONDITIONS
MIN
VOUT ≤ 0.1VRMS, AVCL = 2V/V
MAX4135
185
MAX4136
140
VOUT = 2VP-P, AVCL = 2V/V
MAX4135
185
MAX4136
140
AVCL = 2V/V
Slew Rate Settling Time
TYP
SR
-2V ≤ VOUT ≤ 2V
ts
MHz MHz
40
MHz V/µs
-1V ≤ VOUT ≤ 1V/V, RL = 150Ω, AVCL = 2V/V
to 0.1%
17
to 0.01%
40
DG
f = 3.58MHz, AVCL = 2V/V
MAX4135
0.10
MAX4136
0.10
Differential Phase
DP
f = 3.58MHz, AVCL = 2V/V
MAX4135
0.02
MAX4136
0.02
Off-Isolation
UNITS
1000
Differential Gain
All-Hostile Crosstalk
MAX
ns % degrees
VIN = 1VP-P, f = 30MHz
-50
dB
VIN = 1VP-P, f = 30MHz
75
dB
Channel Switching Off Time
tOFF
25
ns
Channel Switching On Time
tON
25
ns
Digital Switching Feedthrough
VIN = 0VDC
±1
mV
Spurious-Free Dynamic Range
SFDR
fC = 5MHz, AVCL = 2V/V, VOUT = 2VP-P, RL = 100Ω
-72
dBc
Output On-Resistance
ROUT
f = DC, AVCL = 2V/V
1
Ω
Output Off-Resistance
ROUT
f = DC, AVCL = 2V/V
200
kΩ
Output On-Capacitance
COUT(ON)
2
pF
Output Off-Capacitance
COUT(OFF)
3.5
pF
_______________________________________________________________________________________
3
MAX4135/MAX4136
AC ELECTRICAL CHARACTERISTICS
__________________________________________Typical Operating Characteristics (VCC = 5V, VEE = -5V, RL = 150Ω, TA = +25°C, unless otherwise noted.) MAX4136 SMALL-SIGNAL GAIN vs. FREQUENCY (AVCL = 2) 10 9
10 9 8
6
7
7
6
6 5
4
5
3
4
4
2
3
3
1
2
2
0
1
10M
100M
1M
10M
100M
MAX4135 LARGE-SIGNAL GAIN vs. FREQUENCY (AVCL = 2)
MAX4136 LARGE-SIGNAL GAIN vs. FREQUENCY (AVCL = 2) MAX4136 toc04
11
9 8
7
7
GAIN (dB)
8
6
-30
6
-40 -50 -60
4
4
3
3
-90
2
2
-100
1 1M
10M
100M
1M
10M
100M
FREQUENCY (Hz)
ALL-HOSTILE CROSSTALK vs. FREQUENCY
CLOSED-LOOP OUTPUT IMPEDANCE vs. FREQUENCY
1M
10M
100M
1G
INPUT VOLTAGE NOISE vs. FREQUENCY 100
MAX4136 toc08
-20
100k
FREQUENCY (Hz)
800
MAX4135/6 toc07
-10
-80
1G
FREQUENCY (Hz)
0
-70
-110 100k
1G
1G
-20
5
100k
100M
OFF-ISOLATION vs. FREQUENCY
5
1
10M
-10
OFF-ISOLATION (dB)
9
VOUT = 2VP-P
10
1M
FREQUENCY (Hz)
FREQUENCY (Hz)
VOUT = 2VP-P
100k
1G
FREQUENCY (Hz)
11 10
1 100k
1G
MAX4136 toc6
1M
MAX4136 toc05
100k
250
MAX4136 toc09
5
GAIN (dB)
7
8 GAIN (dB)
80 IMPEDANCE (Ω)
-30 -40 -50 -60
NOISE (nV/√Hz)
GAIN (dB)
8
11
MAX4136 toc02
9
GAIN (dB)
11
MAX4136 toc01
10
MAX4136 SMALL-SIGNAL GAIN vs. FREQUENCY (AVCL = 10) MAX4136 toc03
MAX4135 SMALL-SIGNAL GAIN vs. FREQUENCY (AVCL = 2)
CROSSTALK (dB)
MAX4135/MAX4136
1-Input/6-Output Video Distribution Amplifiers
25 8.0 2.5
10
-70 0.8
-80
0.25
-90
0.08
-100 100k
1M
10M FREQUENCY (Hz)
4
100M
1 100k
1M
10M FREQUENCY (Hz)
100M
1
10
100
1k
10k
100k
FREQUENCY (Hz)
_______________________________________________________________________________________
1M
10M
1-Input/6-Output Video Distribution Amplifiers MAX4135 LARGE-SIGNAL PULSE RESPONSE (AVCL = 2)
MAX4136 LARGE-SIGNAL PULSE RESPONSE (AVCL = 2) MAX4135 toc11
IN
GND
OUT
GND
VOLTAGE (500mV/div)
VOLTAGE (500mV/div)
MAX4135 toc10
IN
GND
OUT
GND
10ns/div
10ns/div
MAX4136 SMALL-SIGNAL PULSE RESPONSE (AVCL = 2)
MAX4135 SMALL-SIGNAL PULSE RESPONSE (AVCL = 2)
MAX4135 toc13
IN
GND
OUT
GND
VOLTAGE (50mV/div)
IN
GND
OUT
GND
10ns/div
10ns/div
DIGITAL FEEDTHROUGH MAX4136 toc14
VOLTAGE (50mV/div)
MAX4135 toc12
SEL 1V/div
OUT 45mV/div
20ns/div
_______________________________________________________________________________________
5
MAX4135/MAX4136
Typical Operating Characteristics (continued) (VCC = 5V, VEE = -5V, RL = 150Ω, TA = +25°C, unless otherwise noted.)
Typical Operating Characteristics (continued) (VCC = 5V, VEE = -5V, RL = 150Ω, TA = +25°C, unless otherwise noted.)
-30 -40 -50 -60 2ND HARMONIC
-70 -80
3RD HARMONIC
-90
10M
1M
-0.05 -0.10
-40
-0.15 0
-50
100 IRE
0.01
-60 2ND HARMONIC
-70 -80
3RD HARMONIC
0.00 -0.01 -0.02 -0.03
100K
100M
AVCL = 2V/V RL = 150Ω
1M
10M
100M
0
100
FREQUENCY (Hz)
FREQUENCY (Hz)
IRE
MAX4135 OUTPUT SWING vs. LOAD RESISTANCE
INPUT OFFSET VOLTAGE vs. TEMPERATURE
MAX4135/6 POWER SUPPLY CURRENT vs. TEMPERATURE
8
72
1
71 70
VOLTAGE (mV)
6 5 4 3
CURRENT (mA)
0
7
-1 -2 -3 -4
50
75
100
125
150
67
64 -75 -50 -25
0
25
50
-75 -50 -25
75 100 125 150
0
25
50
75 100 125 150
LOAD RESISTANCE (Ω)
TEMPERATURE (°C)
TEMPERATURE (°C)
INPUT BIAS CURRENT vs. TEMPERATURE
POSITIVE OUTPUT VOLTAGE SWING vs. TEMPERATURE
NEGATIVE OUTPUT VOLTAGE SWING vs. TEMPERATURE
7
2.9
6
-2.3 -2.4 -2.5
4
VOLTAGE (V)
VOLTAGE (V)
2.8
5
2.7 2.6
-2.6 -2.7
3
2.5
-2.8
2
2.4
-2.9
1 -75 -50 -25
0
25
50
75 100 125 150
TEMPERATURE (°C)
MAX4135 toc23
3.0
MAX4135 toc21
8
MAX4135 toc22
25
68
65
-5
0
69
66
2 1
MAX4135 toc-20
9
MAX4135 toc19
2
MAX4135 toc18
10
6
-0.00
-30
-100 100k
MAX4135 toc17
0.05 GAIN (%)
-20
-90
-100
OUTPUT SWING (VP-P)
AVCL = 2V/V VOUT = 2VP-P RL = 100Ω
-10
PHASE (deg)
-20
0
MAX4135 toc16
AVCL = 2V/V VOUT = 2VP-P RL = 100Ω
HARMONIC DISTORTION (dBc)
HARMONIC DISTORTION (dBc)
MAX4135 toc15
0 -10
DIFFERENTIAL GAIN AND PHASE
MAX4136 HARMONIC DISTORTION vs. FREQUENCY
MAX4135 HARMONIC DISTORTION vs. FREQUENCY
CURRENT (µA)
MAX4135/MAX4136
1-Input/6-Output Video Distribution Amplifiers
-3.0
2.3 -75 -50 -25
0
25
50
75 100 125 150
TEMPERATURE (°C)
-75 -50 -25
0
25
50
75 100 125 150
TEMPERATURE (°C)
_______________________________________________________________________________________
1-Input/6-Output Video Distribution Amplifiers PIN
NAME
FUNCTION
MAX4135
MAX4136
1
1
OUT1
Output 1
2, 11
2, 11
VCCO
Positive Supply for Output Amplifiers. Connect to 5V.
3
3
OUT2
Output 2
4, 9, 18, 21
4, 9, 21
AGND
Analog Ground
5
5
OUT3
Output 3
6, 7
6, 7
VEEO
Negative Supply for Output Amplifiers. Connect to -5V.
8
8
OUT4
Output 4
10
10
OUT5
Output 5
12
12
OUT6
Output 6
13
13
SEL6
When low, enables output channel OUT6. When high, disables output channel OUT6.
14
14
SEL5
When low, enables output channel OUT5. When high, disables output channel OUT5.
15
15
SEL4
When low, enables output channel OUT4. When high, disables output channel OUT4.
16
16
VCCI
Positive Supply for Input Amplifier. Connect to 5V.
17
—
N.C.
No Connection. Not internally connected.
—
17
RF
Output of Input Amplifier
—
18
RG
Inverting Input
19
19
VEEI
Negative Supply for Input Amplifier. Connect to -5V.
20
20
IN+
Noninverting Input
22
22
SEL3
When low, enables output channel OUT3. When high, disables output channel OUT3.
23
23
SEL2
When low, enables output channel OUT2. When high, disables output channel OUT2.
24
24
SEL1
When low, enables output channel OUT1. When high, disables output channel OUT1.
_______________Detailed Description The MAX4135/MAX4136 are 1-input/6-output video distribution amplifiers. The MAX4135 is configured for a fixed gain of 2, while the MAX4136 features external gain control (feedback) for closed-loop gains of 2V/V or greater. Each output provides sufficient current to drive five 150Ω loads. However, distortion will increase when driving multiple loads. The TTL/CMOS-compatible digital control (SEL_ ) enables or disables each output amplifier. When the SEL_ control input is low, the amplifier is enabled; when it is high, the amplifier is disabled and presents a high-impedance output. The enable/disable
or disable/enable time is under 25ns, which is useful in multiplexing, pixel switching, or picture-in-picture applications. Each device has an input amplifier, which buffers the input from any switching glitches that may occur at the output stage, and provides a high-impedance, lowcapacitance input. The separate input buffer allows a true high output impedance when an amplifier is disabled. The outputs are protected against short circuits to ground. However, power-dissipation limits preclude shorting all output channels to ground. See the PowerDissipation Considerations section for details.
_______________________________________________________________________________________
7
MAX4135/MAX4136
______________________________________________________________Pin Description
MAX4135/MAX4136
1-Input/6-Output Video Distribution Amplifiers 75Ω*
+5VDC
0.1µF 75Ω*
MAX4135 OUT1 1
OUT1
VCCO 2 OUT2 3
OUT2
SW1
SEL1 24
SW2
SEL2 23
SW3
SEL3 22
AGND 4 75Ω*
-5VDC
0.1µF 75Ω*
75Ω*
+5VDC 0.1µF 75Ω*
OUT3 5
AGND 21
IN
75Ω*
VEEO 6 VEEO 7 OUT4 8 AGND 9
IN+ 20
OUT3
VIDEO IN
RF
OUT4
OUT5 10 VCCO 11
OUT5
OUT6 12
OUT6
RG
-5VDC
VEEI 19
0.1µF
AGND 18 N.C. 17 VCCI 16
0.1µF
SW4
SEL4 15
SW5
SEL5 14
SW6
SEL6 13
+5VDC
* TO TERMINATE TRANSMISSION LINE
Figure 1. MAX4135 Typical Operating Circuit
__________Applications Information Grounding, Bypassing, and PC Board Layout To obtain the MAX4135/MAX4136’s full 185MHz bandwidth, Microstrip and Stripline techniques are recommended in most cases. To ensure that the PC board does not degrade the amplifier’s performance, design the board for a frequency greater than 1GHz. Even with very short traces, use these techniques at critical points, such as inputs and outputs. Whether you use a constant-impedance board or not, observe the following guidelines when designing the board:
8
• Do not use wire-wrap boards. They are too inductive. • Do not use IC sockets. They increase parasitic capacitance and inductance. • In general, surface-mount components have shorter leads and lower parasitic reactance, giving better high-frequency performance than through-hole components. • The PC board should have at least two layers, with one side a signal layer and the other a ground plane. • Keep signal lines as short and straight as possible. Do not make 90° turns; round all corners. • The ground plane should be as free from voids as possible.
_______________________________________________________________________________________
1-Input/6-Output Video Distribution Amplifiers
+5VDC 0.1µF 75Ω*
75Ω*
-5VDC 0.1µF 75Ω*
75Ω*
+5VDC 0.1µF 75Ω*
MAX4135/MAX4136
75Ω*
MAX4136 OUT1 1
OUT1
VCCO 2 OUT2 3
OUT2
SW1
SEL1 24
SW2
SEL2 23
SW3
SEL3 22
AGND 4
AGND 21
OUT3 5
IN+ 20
OUT3 IN
75Ω*
VEEO 6 VEEO 7 OUT4 8 AGND 9
VIDEO IN
-5VDC
VEEI 19 RG 18
OUT4
RF 17 VCCI 16
OUT5 10 VCCO 11
OUT5
OUT6 12
OUT6
SW4
SEL4 15
SW5
SEL5 14
SW6
SEL6 13
0.1µF
RF
RG
+5VDC 0.1µF
* TO TERMINATE TRANSMISSION LINE
Figure 2. MAX4136 Typical Operating Circuit
Driving Capacitive Loads The MAX4135/MAX4136 provide maximum AC performance with no output load capacitance. This is the case when they are driving a correctly terminated transmission line (i.e., a back-terminated 75Ω cable). However, the MAX4135/MAX4136 are capable of driving capacitive loads up to 10pF without oscillations, but with reduced AC performance. Driving large capacitive loads increases the chance of oscillations in most amplifier circuits. This is especially true for circuits with high loop gain, such as voltage followers. The amplifier’s output resistance and the load capacitor combine to add a pole and excess phase to
the loop response. If the frequency of this pole is low enough and phase margin is degraded sufficiently, oscillations may occur. A second problem when driving capacitive loads results from the amplifier’s output impedance, which looks inductive at high frequencies. This inductance forms an L-C resonant circuit with the capacitive load, which causes peaking in the frequency response and degrades the amplifier’s gain margin. The MAX4135/MAX4136 drive capacitive loads up to 10pF without oscillation. However, some peaking (in the frequency domain) or ringing (in the time domain) may occur (Figure 3).
_______________________________________________________________________________________
9
14 12 CLOSED-LOOP GAIN (dB)
RISO
10
CL = 15pF CL = 10pF CL = 5pF
8
VOUT VIN
RL
CL
6 4 2
MAX4135 MAX4136
0 0.1M
1M
10M
100M
1G
FREQUENCY (Hz)
Figure 3. Effect of CLOAD on Frequency Response (without RISO)
To drive larger-capacitance loads or to reduce ringing, add an isolation resistor between the amplifier’s output and the load, as shown in Figure 4. The value of RISO depends on the circuit’s gain and the capacitive load. Figure 5 shows the optimal isolation resistor (RISO) vs. capacitive load (CL). At the higher capacitor values, the bandwidth is dominated by the RC network, formed by RISO and CL.
Power-Dissipation Considerations The MAX4135/MAX4136 can drive up to six outputs simultaneously. Quiescent power dissipation is typically 750mW and 800mW maximum, respectively, with all channels enabled. The maximum package power dissipation is rated at 1540mW. In a typical application, six outputs drive a standard video signal into a 150Ω load. The amount of power added to the quiescent dissipation is minimal and no special precautions are necessary. However, each output driving the maximum 65mA into 30Ω will cause a power-dissipation increase of approximately 200mW. Therefore, you should not allow more than three outputs to deliver that load simultaneously. Similarly, one output shorted to ground will cause a power-dissipation increase of 650mW. Only one output can be shorted to ground without violating the package power rating.
10
Figure 4. Capacitive-Load Driving Circuit
16 15 RISOLATION (Ω)
MAX4135/MAX4136
1-Input/6-Output Video Distribution Amplifiers
14 13 12 11 10 10
40
70
100
130
160
190
220
CLOAD (pF)
Figure 5. Optimal Isolation Resistor (RISO) vs. CLOAD
In conclusion, during normal operation in a matchedload environment, the total power dissipation is well within the package’s dissipation rating. The maximum power dissipation is violated only if multiple channels are driving the maximum current into minimum loads at the same time.
______________________________________________________________________________________
1-Input/6-Output Video Distribution Amplifiers MAX4135/MAX4136
SC1M3 SC1M2 SC1M1 SEL1
OUT1 OUT2
SEL2 CAMERA 1 SUBCARRIER (SC1)
SEL3
OUT3
SEL4
OUT4
IN
OUT5
75Ω SEL5
75Ω
OUT6
VIDEO
SEL6 SC1M6 SC1M5 SC1M4
MAX4135 MAX4136
SYNC
75Ω
75Ω
MONITOR 1
75Ω VIDEO
SC2M3 SC2M2 SC2M1
SYNC SEL1
OUT1
75Ω
75Ω MONITOR 2
OUT2
SEL2 CAMERA 2 SUBCARRIER (SC2)
75Ω
SEL3
OUT3
SEL4
OUT4
IN
VIDEO OUT5
75Ω SEL5
SYNC
75Ω
75Ω
MONITOR 3
OUT6
MONITOR INPUTS
SEL6 SC2M6 SC2M5 SC2M4
75Ω
MAX4135 MAX4136
VIDEO
75Ω M3 M2 M1
75Ω
MONITOR 4
VIDEO
OUT1
75Ω
OUT2
75Ω
SYNC
75Ω
OUT3
75Ω
75Ω
MONITOR 5
SEL3 SEL4
OUT4
75Ω
OUT5
75Ω
OUT6
75Ω
SEL2 IN
75Ω SEL5 SEL6 M6 M5 M4
75Ω
75Ω SEL1
COMPOSITE SYNC (FROM GENLOCK)
SYNC
VIDEO SYNC
75Ω
75Ω
MONITOR 6
MAX4135 MAX4136
Figure 6. Two Cameras to Six Monitors Distribution Amplifier
______________________________________________________________________________________
11
___________________Chip Information TRANSISTOR COUNT: 901 SUBSTRATE CONNECTED TO VEE
Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.)
SOICW.EPS
MAX4135/MAX4136
1-Input/6-Output Video Distribution Amplifiers
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600 © 1999 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
