Mb10-ds Series Quick Reference Guide/ 快速测试参考指南

Transcript

MB10-DS Series Quick Reference Guide/ 快速测试参考指南 2 36 3 5 4 6 7 8 9 35 10 34 Speed LED Link/Activity LED 16 15 14 13 33 29 28 27 26 25 23 ATX Power/ 电源 1 5 PMBUS No. 1 2 3 4 5 6 7 8 9 10 11 12 Pin Define 3.3V 3.3V GND +5V GND +5V GND Power Good 5VSB +12V +12V 3.3V No. 13 14 15 16 17 18 19 20 21 22 23 24 Pin Define 3.3V -12V GND PS_ON GND GND GND -5V +5V +5V +5V GND No. 1 2 3 4 Pin Define GND GND GND GND No. 5 6 7 8 Pin Define +12V +12V +12V +12V 5 3 2 1 No. 1 3 5 7 9 11 13 15 17 19 21 23 Pin Define Power LED+ No Pin Power LEDHDD LED+ HDD LEDPower Button GND Reset Button+ GND ID Switch+ ID SwitchNMI Switch- No. 2 4 6 8 10 12 14 16 18 20 22 24 Pin Define 5V Standby ID LED+ ID LEDSystem Status LED+ System Status LEDLAN1 Active LED+ LAN1 Link LEDSMBus Data SMBus Clock Case Open LAN2 Active LED LAN2 Link LED- 7 1 Pin Define GND TXP TXN GND Pin Define RXN RXP GND 12QM1-MB10D0-00R 1 No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Pin Define Clock GND Data 26 25 Pin Define BP_SGP_CLK BP_SGP_GLD BP_SGP_DOUT Key Pin GND BP_LED_G_N BP_SGP_DIN GND GND P_3V3_AUX P_3V3_AUX GND BP_PRESENSE No. 1 3 5 7 9 11 13 15 17 19 21 23 25 No. 1 5 2 3 Pin Define No. 4 SDIN 5 GND SDOUT Pin Define SLOAD SCLK Speed LED Link/Activity LED 5 Speed LED Desription System Status LED Power button w/LED ID switch button w/LED VGA port USB 3.0 ports KVM Server Management 10/100/1000 LAN Port (Dedicated LAN Port) LAN ports SFP+ LAN ports (MB10-DS3/MB10-DS4/MB10-DS5) BMC F/W Readiness LED 14 13 Pin Define CLK P_3V3_AUX LPC_RST P3V3 LPC_LAD0 IRQ_SERIAL LPC_LAD1 No Connect LPC_LAD2 No Connect LPC_LAD3 GND LPC_FRAME_N GND BMC Firmware Readiness LED (LED_BMC1): State Description On BMC firmware is initial Blink BMC firmware is ready Off AC loss No. 2 4 6 8 10 12 14 16 18 20 22 24 26 CPU/System FAN/ 风扇 Description State Description Yellow On 1Gbps data arte Green On Normal operation Green On 100Mbps data arte Amber On Critical alert. 10Mbps data arte Off 4 1 No. 1 2 3 4 4 1 Pin Define GND +12V Sense Speed Control Power button/LED: Link/Activity LED State SFP+ LAN LED: State Description Yellow On 1Gbps data rate Green On 10 Gbps data rate 4 No. 1 2 3 4 Pin Define No Connect FAN_SGP_GLD GND Reset BP_LED_A_N GND No Connect SMB_BP_DATA SMB_BP_CLK BMC_ACK BMC_REQ Key Pin GND No. 1 2 3 4 5 6 7 8 9 10 Pin Define NDCDNSIN NSOUT NDTRGND NDSRNRTSNCTSNRINo Pin Description Green On System is powered on Off System is powered off ID switch button w/LED: State Blue On Type Description Unit selected for identification No identification Speed (MT/s); Slot Per Channel (SPC) and DIMM Per Channel (DPC) Ranks PerDIMM and Data Width 1DPC 2DPC SRx4 ECC 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* RDIMM SRx8 ECC 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* RDIMM DRx8 ECC 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* RDIMM DRx4 ECC 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* RDIMM Pin Define GND SMBUS Data SMBUS Clock GND 2 Slot Per Channel 1 Slot Per Channel 1DPC NVME Connector 1 System is not ready Memory Population Configuration/ 安装内存  Note: DDR4 2400MHz is only available on Intel Xeon® D-1541 processor.  When only one DIMM is used, it must be populated in memory slot0 first.  System will not boot normally with incorrect populated sequence.  仅Intel Xeon® D-1541处理器支持DDR4-MHz内存。  只使用一个DIMM时，必须安装到内存插槽0。  若安装顺序有误，系统将不能正常引导。 Jumper Settings/ 跳线设置 4 Serial Port Cable Connector/ 串行端口 9 10 System Status LED: State Off 1 2 12 Description SATA 3 6Gb/s connector SATA 3 6Gb/s connector SATA 3 6Gb/s connectors SATA 3 6Gb/s connectors SATA SGPIO header System fan connector#2 Serial port cable connector BMC firmware readiness LED HDD back plane board header NVME connector TPM module connector IPMB connector Clear CMOS jumper PCI Express x16 slot ME update jumper ME recovry jumper S3 Power On Select jumper 10/100/1000 LAN LED: 8 HDD Back Plane Board Header/ 硬盤背板排針 SATA SGPIO Header/ 串行 GPIO SATA Connector/SATA 接口 No. 1 2 3 4 No. 5 6 7 1 No. 1 2 3 Code SATA0 SATA1 SATA_2_3 SATA_4_5 SATA_SGPIO SYS_FAN 2 COM1 LED_BMC1 BP_1 NVME_PH TPM IPMB CLR_CMOS PCIE_1 ME_UPDATE ME_RCVR S3_MASK Off 2 1 Pin Define PMBus Clock PMBus Data PMBus Alert GND 3.3V Sense 7 2 3 TPM Connector/ 可信平台模块 IPMB Front Panel Header/ 前面板 24 23 No. 1 2 3 4 5 1 4 1 No. 1 2 3 4 5 6 7 8 22 21 20 19 18 No. 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Rear I/O Connector/ 后面板接口 12 17 24 4 8 SFP+1_2 LAN1_2 USB3_MLAN CPU0_FAN VGA SW_ID SW_PWR LED_STA P12V_AUX2 FP_1 ATX1 DIMM_P0_A0 DIMM_P0_A1 DIMM_P0_B0 DIMM_P0_B1 BAT1 PMBUS SATA_DOM0 6 32 24 12 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Description Intel Xeon® processor D-1541, FCBGA1667 SoC (MB10-DS0/3) Intel Xeon® processor D-1521, FCBGA1667 SoC (MB10-DS1/4) Intel Xeon® processor D-1581, FCBGA1667 SoC (MB10-DS2/5) SFP+ LAN connectors#1/#2 LAN ports BMC Management LAN port (top) / USB 3.0 ports (bottom) CPU fan connector VGA port ID switch button w/LED Power button w/LED System Status LED 8 pin power connector Front panel header 24 pin main power connector Channel 1 slot 0 Channel 2 slot 1 Channel 3 slot 0 Channel 4 slot 1 Battery PMBus connector SATA port 0 DOM support jumper 11 30 13 Code CPU 1 31 1 No. 1 No. 1 Desription Clear CMOS Jumper 1-2 Close: Normal operation (Default setting) 2-3 Close: Clear CMOS data. 2 ME Update Jumper 1-2 Close: ME update. 2-3 Close: Normal operation (Default setting) 3 ME Recovery Jumper 1-2 Close: Normal operation. (Default setting) 2-3 Close: ME recovery mode. 4 S3 Power On Select Jumper 1-2 Close: Stop an initial power on when BMC is not ready. 2-3 Close: Keep initial power on. (Default setting) 5 SATA Port 0 DOM Support Jumper Jumper 1-2 Close: Enable SATA port DOM support funtion. 2-3 Close: Normal Operation. (Default setting) 3 2 1 Pin No. 5 Definition 1 P5V 2 GND 3 NC If a SATA type hard drive is connected to the motherboard, please ensure the jumper is closed and set to 2-3 pins (Default setting), in order to reduce any risk of hard disk damage.