Transcript
Bulletin PD-2.319 rev. C 01/03
MBR1635/ MBR1645 MBRB1635/ MBRB1645 SCHOTTKY RECTIFIER
16 Amp
Description/ Features
Major Ratings and Characteristics
The MBR16.. Schottky rectifier has been optimized for low reverse leakage at high temperature. The proprietary barrier technology allows for reliable operation up to 150° C junction temperature. Typical applications are in switching power supplies, converters, free-wheeling diodes, and reverse battery protection.
Characteristics
MBR16..
Units
IF(AV) Rectangular
16
A
VRRM
35/45
V
IFSM @ tp = 5 µs sine
1800
A
High purity, high temperature epoxy encapsulation for enhanced mechanical strength and moisture resistance
VF
0.57
V
Low forward voltage drop High frequency operation
- 65 to 150
°C
Guard ring for enhanced ruggedness and long term reliability
waveform
@ 16 Apk, TJ = 125°C
TJ
150° C TJ operation
Case Styles MBR1635/ MBR1645
MBRB1635/ MBRB1645
Base Cathode
Base Cathode 2
1
Cathode
3
Anode
TO-220AC www.irf.com
1
3
Anode
N/C
D2PAK 1
MBR1635/ MBR1645, MBRB1635/ MBRB1645 Bulletin PD-2.319 rev. C 01/03
Voltage Ratings Part number VR
MBR1635
MBR1645
Max. DC Reverse Voltage (V) 35
VRWM Max. Working Peak Reverse Voltage (V)
45
Absolute Maximum Ratings Parameters
MBR16.. Units
IF(AV) Max. Average Forward Current IFSM
16
Non-Repetitive Peak Surge Current
A
1800 A 150
EAS
Non-Repetitive Avalanche Energy
24
mJ
IAR
Repetitive Avalanche Current
3.6
A
Conditions @ TC = 125 °C, (Rated VR) Following any rated load 5µs Sine or 3µs Rect. pulse condition and with rated VRRM applied Surge applied at rated load condition halfwave single phase 60Hz TJ = 25 °C, IAS = 3.6 Amps, L = 3.7 mH Current decaying linearly to zero in 1 µsec Frequency limited by TJ max. VA = 1.5 x VR typical
Electrical Specifications Parameters VFM IRM
MBR16.. Units
Max. Forward Voltage Drop(1)
Conditions
0.63
V
@ 16A
TJ = 25 °C
0.57
V
@ 16A
TJ = 125 °C
Max. Instantaneus Reverse Current
0.2
mA
TJ = 25 °C
(1)
40
mA
TJ = 125 °C
Rated DC voltage
CT
Max. Junction Capacitance
1400
pF
VR = 5VDC, (test signal range 100Khz to 1Mhz) 25°C
LS
Typical Series Inductance
8.0
nH
Measured from top of terminal to mounting plane
10000
V/ µs
dv/dt Max. Voltage Rate of Change (Rated VR) (1) Pulse Width < 300µs, Duty Cycle <2%
Thermal-Mechanical Specifications Parameters
MBR16.. Units
TJ
Max. Junction Temperature Range
-65 to 150
Tstg
Max. Storage Temperature Range
-65 to 175
Conditions
°C °C
RthJC Max. Thermal Resistance Junction to Case
1.50
°C/W DC operation
RthCS Typical Thermal Resistance, Case to Heatsink
0.50
°C/W Mounting surface, smooth and greased
wt
Approximate Weight
T
Mounting Torque Case Style
2
2 (0.07)
g (oz.)
Min.
6 (5)
Max.
12 (10)
Kg-cm (Ibf-in)
TO-220AC
JEDEC
www.irf.com
MBR1635/ MBR1645, MBRB1635/ MBRB1645 Bulletin PD-2.319 rev. C 01/03 1000
1000
T =175°C J
ReverseCurrent - I (mA) R
100
125°C 1
100°C 75°C
.1
50°C .01 25°C .001 .0001 0
10
T =125°C J
Fig. 2 - Typical Values of Reverse Current Vs. Reverse Voltage 10000
1
.2
.4
.6
.8
10 15 20 25 30 35 40 45 ReverseVoltage- VR(V)
T = 25°C J
.1 0
5
T =175°C J
JunctionCapacitance- C (pF) T
InstantaneousForwardCurrent - IF (A)
100
150°C 10
1
1.2
1.4
T =25°C J 1000
100 0
1.6
10
20
30
40
50
ReverseVoltage- V (V) R
ForwardVoltageDrop- V (V) FM
Fig. 1 - Maximum Forward Voltage Drop Characteristics
Fig. 3 - Typical Junction Capacitance Vs. Reverse Voltage
Thermal Impedance- ZthJC(°C/W )
10
1
.1
D=0.50 D=0.33 D=0.25 D=0.17 D=0.08
P DM
t 1 t2 Notes: 1. Dutyfactor D= t1/ t2
.01 SinglePulse (Thermal Resistance) .001 .00001
.0001
.001
2. PeakT =P xZ +T J DM thJC C .01
.1
1
10
100
t , Rectangular PulseDuration(Seconds) 1
Fig. 4 - Maximum Thermal Impedance ZthJC Characteristics
www.irf.com
3
MBR1635/ MBR1645, MBRB1635/ MBRB1645 Bulletin PD-2.319 rev. C 01/03
15 18TQ RthJC (DC) =1.50°C/W
175
AveragePower Loss - (Watts)
AllowableCaseTemperature- (°C)
180
170 165 DC
160 155 150 0
4
8
12
16
20
24
D=0.08 D=0.17 D=0.25 D=0.33 10 D=0.50
5
0 0
28
DC
RMSLimit
4
8
12
16
20
AverageForwardCurrent - I
AverageForwardCurrent - IF(AV) (A)
Fig. 5 - Maximum Allowable Case Temperature Vs. Average Forward Current
24
F(AV)
28
(A)
Fig. 6 - Forward Power Loss Characteristics
(A)
10000
Non-Repetitive Surge Current - I
FSM
At Any Rated Load Condition And With Rated VRRM Applied Following Surge
1000
100 10
100
1000
10000
Square Wave Pulse Duration - t p (microsec)
Fig. 7 - Maximum Non-Repetitive Surge Current L
DUT
IRFP460 Rg = 25 ohm
CURRENT MONITOR
HIGH-SPEED SWITCH FREE-WHEEL DIODE
+
Vd = 25 Volt
40HFL40S02
Fig. 8 - Unclamped Inductive Test Circuit
4
www.irf.com
MBR1635/ MBR1645, MBRB1635/ MBRB1645 Bulletin PD-2.319 rev. C 01/03
Outline Table 10.54 (0.41)
1.32 (0.05)
MAX.
3.78 (0.15)
1.22 (0.05)
DIA. 3.54 (0.14) 6.48 (0.25) 6.23 (0.24)
2.92 (0.11) 2.54 (0.10) TERM 2
15.24 (0.60) 14.84 (0.58) 1
2°
3
14.09 (0.55)
3.96 (0.16)
13.47 (0.53)
3.55 (0.14)
Base Cathode
0.10 (0.004)
2.04 (0.080) MAX. 1.40 (0.05)
2.89 (0.11)
1.15 (0.04)
2.64 (0.10)
0.94 (0.04) 0.69 (0.03)
1
Cathode 1
3
3
Anode
0.61 (0.02) MAX.
4.57 (0.18) 4.32 (0.17)
5.08 (0.20) REF.
Conform to JEDEC outline TO-220AC Dimensions in millimeters and (inches)
4.69 (0.18) 4.20 (0.16)
10.16 (0.40) REF.
1.32 (0.05)
1.22 (0.05)
6.47 (0.25) 15.49 (0.61)
93°
6.18 (0.24)
14.73 (0.58)
5.28 (0.21)
2.61 (0.10)
4.78 (0.19)
2.32 (0.09)
0.55 (0.02)
8.89 (0.35)
3X
REF.
1.40 (0.055)
1.14 (0.045) 2X
0.46 (0.02)
0.93 (0.37)
MINIMUM RECOMMENDED FOOTPRINT
0.69 (0.27)
11.43 (0.45)
Base Cathode 2
1
3 4.57 (0.18)
4.32 (0.17)
8.89 (0.35)
17.78 (0.70)
2 0.61 (0.02) MAX. 5.08 (0.20) REF.
1
N/C
3.81 (0.15)
3
Anode
2.08 (0.08) 2X
2.54 (0.10) 2X
Conform to JEDEC outline D2Pak (SMD-220) Dimensions in millimeters and (inches)
www.irf.com
5
MBR1635/ MBR1645, MBRB1635/ MBRB1645 Bulletin PD-2.319 rev. C 01/03
Tape & Reel Information TRR 1.60 (0.063) 1.50 (0.059) 4.10 (0.161) 3.90 (0.153)
FEED DIR ECTION
1.60 (0.063) 1.50 (0.059)
1.85 (0.073)
DIA. 0.368 (0.0145) 0.342 (0.0135)
11.60 (0.457)
1.65 (0.065)
11.40 (0.449) 15.42 (0.609) 15.22 (0.601)
TRL 1.75 (0.069) 10.90 (0.429)
1.25 (0.049)
10.70 (0.421)
24.30 (0.957) 23.90 (0.941)
DIA. 4.72 (0.186)
16.10 (0.634)
4.52 (0.178)
15.90 (0.626) FEED DIRECTION
13.50 (0.532)
26.40 (1.039)
12.80 (0.504) DIA.
24.40 (0.961)
SMD-220 Tape & Reel When ordering, indicate the part number, part orientation, and the quantity. Quantities are in multiples 60 (2.362)
360 (14.173)
of 800 pieces per reel for both TRL and TRR.
D IA . MIN .
DIA. MAX.
Dimensions in millimeters and (inches)
Ordering Information Table Device Code
MBR
B
16
45
1
2
3
4
1
-
Essential Part Number
2
-
Package Style: none= TO-220 B
6
3
-
Current Rating
4
-
Voltage Rating
= D2 Pak 35 = 35V 45 = 45V
www.irf.com
MBR1635/ MBR1645, MBRB1635/ MBRB1645 Bulletin PD-2.319 rev. C 01/03
Data and specifications subject to change without notice. This product has been designed and qualified for Industrial Level. Qualification Standards can be found on IR's Web site.
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 01/03
www.irf.com
7
