Preview only show first 10 pages with watermark. For full document please download

Mcx Series - Audio Equipment

   EMBED


Share

Transcript

MCX Series Technical Data Designed for permanently installed sound systems where rackspace is at a premium, KIND’s MCX series provide unprecedented levels of channel density for multichannel amplifiers. The MCX 84-6 and MCX 124-6 provide 80 watts and 120 watts per channel at 4 ohm respectively. A four or six channel amplifier can be easily transformed in a stereo or three channel amplifier doubling its power and this is value for your investment, XLR inputs offers professional connection way. MCX are really complete for their filed application, because fitted with internal x-over and with Clip limiter. High quality, reliability, sound performance and best value make them very attractive. Basically MCX are 4-6 independent channel amplifier, which can be configured through a set of switches situated inside and on rear panel. The different setup configuration allow to those amplifiers to be usefull for many situations, for example: • 4-6 zones with different level and program • 4-6 zones with different level and same program (all chennels will share one input) • MCX 84/124 to drive one mono sub with two channel bridged (with 100Hz LPF) and two satellite with two ste reo channel (with 100Hz HPF) • MCX 86/126 to drive one mono sub with two channel bridged (with 100Hz LPF) and four satellite with four stereo channel (with 100Hz HPF) For low noise and power demand toroidal transformer and a large capacitors bank is used in the MCX models. The MCX Series incorporates comprehensive protection features to safeguard the amplifier and all connected loudspeaker drivers. The protections are inaudible under normal use and all protection circuitry are independent for each channel. A circuit limit the current at the channel’s output if a full short is made between a positive output and GND. The temperature management system constantly monitors the heatsink temperature. If the heatsink reaches an abnormal temperature the amplifier’s channel will be muted until temperature decrease to normal operating level with an automatic reset system. MCX Benefits • Compact Design: 2 RU spaces 13 kg - 6x120W (MCX 126) • Channel pairs bridgeable for maximum flexibility • Fitted with internal x-over 100Hz Hi-Low pass filter • Selectable high-pass filters protect speakers and prevent speaker transformer saturation with minimal effect on program material • Convection Cooling System allow low noise operation • DIP switch to Link Inputs (bus) for easy and fast connectivity • DIP switch control for clip limiters, high/low-pass filters, bridge mono • Active inrush limiting eliminates AC inrush current, removing the need for expensive power sequencers • User-defeatable clip limiters reduce distortion • Front mounted stepped gain controls knobs for easy access • Signal and Clip LED indicators to monitor performance • Balanced XLR/F and link bus for simple loop-through connectivity • Detachable europlug (Phoenix) output connectors • Fully protected — including DC, infrasonic and ultrasonic, thermal overload and short circuit protection The convection cooling allow very low noise operation. • Craftsmen built in Galliate, Italy The MCX series have a professional look and a very strong chassis; The circuit board design is modular, because this type of construction greatly improves future technical assistance. • 3 year Warranty Audible Power Solutions Specifications Model Number of channels MCX 84 4 MCX 124 4 MCX 86 6 MCX 126 6 Power Output Per Channel1) 16 ohms per ch. (all channels driven) 8 ohms per ch. (all channels driven) 4 ohms per ch. (all channels driven) 30 W 50 W 80 W 50 W 90 W 120 W 30 W 50 W 80 W 50 W 90 W 120 W Power Output Bridged1) 16 ohms per ch. 8 ohms per ch. 100 W 160 W 180 W 240 W 100 W 160 W 180 W 240 W Performance THD+N 20 Hz - 20kHz for 1 W @ 4 ohms THD @ 1 kHz 1dB below clipping @ 4 ohms Signal to Noise Ratio Frequency Response (1 W @ 8 ohms) +0/-1dB Damping Factor @ 8 ohms load, 10 Hz to 200 Hz Output Slew rate @ 8 ohms (input filter bypassed) Input Impedance Balanced / Unbalanced Input CMRR <0.05% <0.1% >106 dB 20Hz - 20kHz >200 20V /uS 20k / 10kOhm >50 dB <0.05% <0.1% >106 dB 20Hz - 20kHz >200 20V /uS 20k / 10kOhm >50 dB <0.05% <0.1% >106 dB 20Hz - 20kHz >200 20V /uS 20k / 10kOhm >50 dB <0.05% <0.1% >106 dB 20Hz - 20kHz >200 20V /uS 20k / 10kOhm >50 dB Gain and Level Input Sensitivity @ 4 ohms +/- 3 % Input Gain Level Adjustment (per channel) 0.775 V 0.775 V 27.3 dB 29 dB Front panel potentiometer, 21 pos. stepped gain from -80 to 0 dB 0.775 V 27.3 dB 0.775 V 29 dB Front panel Indicators Per channel Active (unit power on); Signal output -30 dB; Clip / Limit; Connectors and switches Input connectors (per channel) Output connectors (per two channels) Output bridge mode per two channels Rear panel 4 position DIP switches per two channels Internal 3 position DIP switches per channel Power (on/off) Balanced: XLR/Female; pin 2 positive 4-pin detachable Europlug (Phoenix) A+B - ch. A is signal input source and pot. A is level control Ch. A / B Limiter on; Ch.’s A+B Link on, Stereo/Bridge on; Ch.’s B+C Link on Full range on, Low Pass Filter on (100 Hz - 18 dB/oct), High Pass Filter on (100 Hz - 18 dB/oct) Switch on front panel Output Circuitry / Design Topology Power Supply Cooling I.C. Class AB I.C. Class H Linear power supply with toroidal transformer Convection system Amplifier and Load Protection Short circuit, open circuit, thermal, RF protection. On/off muting, clip limiter Power Operating voltage (selectable inside the unit) Current draw @ 230 V AC 1/8 power 4 ohms Current draw @ 230 V AC 1/3 power 4 ohms Current draw @ 230 V AC, idle Soft start / Inrush current draw @230 V AC AC cordset Nominal 115V AC (75-132V AC) - 50/60 Hz, min. power up voltage 90 V; or nominal 230V AC (150-264V AC) - 50/60 Hz, min. power up voltage 180 V 0.8 A 1.0 A 1.1 A 1.4 A 1.6 A 2.0 A 2.3 A 3.0 A 0.1 A 0.1 A 0.1 A 0.1 A Yes / max. 3 A per channel 230 V CE: 16 A, CEE7; 115 V ETL: 15 A, NEMA-15 Dimensions (W/H/D) Weight - Net / Shipping W: 483 mm (19”), H: 88.9 mm (3.5” - 2 RU), From front mounting rails D: 391 mm (15.4”) 9 kg (19.8 lbs.) / 12 kg (26.4 lbs) 11 kg (24.2 lbs) / 14 kg (30.8 lbs) 11 kg (24.2 lbs) / 14 kg (30.8 lbs) Approvals CE EN55103-1 (Emissions), EN55103-2 (Immunity), EN60065, Class I (Safety) I.C. Class AB I.C. Class H 13 kg (28.6 lbs) / 16 kg (35.2 lbs) Note 1) EIA 1kHz - 1% THD @ 230 V AC All specifications are subject to change without notice. ������������ ��������������������������� ������������������� �� ������ �� ���� �� ���� �� �������������� �������������� ���� ����������������� ���� ������������������ ������������� ���� ����������������� ���� ������ ��� ���� �������������� �������������� ���� ����������������� ���� ������ ��� ���� ������������������ ������������� ���� ����������������� ���� ��������� ������� ���� ������ ��� �������������� �������������� ���������� ������������������ ������������ �������������������������� ����������������������������� ����������������������� �������������������� ������������� ��� � �� � �� �� ���� �� ����������������� �������� ���������������������� ����������������������� �������� �������������������������������������� �������������������������������� ��������������������������������������� �������������������������������������� ����������������������������������������� ���������������������������������� ������������������ ������������� MCX-4 ch’s. ����������������� ���������������������� ����������������������� ������������������� ������������������� ���������������� ����������������� MCX-6 ch’s. ���� �� ������� ������� ���� ���� ���� ���� ���� ���� � ������ � � ������ � � ������ � RoHS Compliant Lead-Free KIND is a trademark of A&AG S.r.l. Via Montello, 19 - 28066 Galliate (NO) ITALY - Tel. +39 0321 865271 - Fax +39 0321 861674 - e-mail: [email protected] Item no. TDS-MCX-V01-06/03/08 kindaudio.com