Transcript
Since 1987 Developed, Created and Made in Spain
MDV6/MD6V
TRANSMITTER/RECEIVER 4xVIDEO, DATA, AUDIO & CONTACT
CONTENTS General functionality and features of the equipment Technical specifications Application Connection scheme for standalone version Connection scheme for rack assembly version Light signalling description for standalone version Light signalling description for rack assembly version Configuration
The central pages contain a 1:1 scale template of the fixation for standalone version.
MDV6/MD6V MULTIPLEXER 4 VIDEO CHANNELS + DATA TRANSCEIVER, AUDIO AND CONTACT MDV6 TX 4ch Video + 2 x Data + 2 x Audio + Contact
MD6V RX 4ch Video + 2 x Data + 2 x Audio + Contact 1 Fiber
(-40° to 74°C ) Industrial Range
- Transmitter / Receiver of 4 video channels + Tranceiver of 2 Data channels + 2 Audio channel and 1 contact channel.Reach up 2.5km for Multimode fiber (MM) and 60 km for Singlemode fiber (SM), always over transmissions point to point. - Power supply: from 12 to 24 Vac/Vdc. - Mechanical formats: Standalone & DIN Rail. - Industrial temperature range, -40° to 74°C. MDV6/MD6V allow links point to point for transmissión digital of 4 video channels + 2 data transceivers, 2 bidirectional audio and 1 contact over 1 Fiber optic up 60 km depending of version. Additionally to transmission /reception of video, implements next functions: Two bidirectional channels of communications compatible with Standard EIA/TIA/RS-232, 422 and 485 over 2 or 4 wires. Configurable time forced for RS485 transmission. Terminating resistor selectable for the differential communication. Two bidirectional audio channels with differential mode input or unipolar. Transmission / reception of free contact. Configuration PC through serial port. Setting for the remote device through the PC of control center. Led signal for verification of links, contact, remote/local connection, data and audio transmission. Plug and Play design faciliting installation and verification. Digital video transmission allows reach longer distances improving at same time high quality image.
Transmitter
Receiver
Wavelength
Connector
Fiber
Max loss.1
MDV645N16
MD6V46N16
1310/1550nm 1550/1310nm
SC
1 x MM (62,5/125 or 50/125)
23dB (50/125: 2.5 km)2 (62.5/125: 2 km)2
MDV645M16
MD6V46M16
1310/1550nm 1550/1310nm
SC
1 x SM (9/125)
23dB (60 km)
(1) Attenuations: At 1310nm, 1dB Km for 62.5/125 and 0.7dB/km for 50/125. For 9/125, 0.3dB/km. (Ideal conditions) (2) Maximum distance restriction due to the fiber modal bandwith (with ideal conditions).
Technical specifications: Video
Input/output impedance Input/output voltage Video connector Bandwidth SNR Sync error Differential gain Differential phase C/L Gain
75 Ω 1,2 Vppmax BNC 10 Hz – 6 MHz > 60 dB < 5.0 % < 2.5 % < 2º <5%
Communications
Data forma selectable Data rate Data connector Resistor for RS422/RS485
RS232/422/485 up 115.2 kbps RJ45 120 Ω
Audio
Input voltage max. Input Impedance Output Impedance Resolution A/D SNR Bandwidth
3 Vpp 9 kΩ 600 Ω 12 bits >60dB 18 kHz
Contact
Max. contact current Max. contact voltage Max. contact power Contact impedance Input
2A 220Vdc 60W 100m Ω Active low
Optic characteristics
Multimode optical power Multimode receiver sensitivity Singlemode optical power Singlemode receiver sensitivity
-3dBm -26dBm -3dBm -26dBm
General
Consumption MDV6/ND6V Max. power MDV6/ND6V1 Power system MTBF Dimensions MDxx4xx16 (standalone/ DIN rail) Weight Operating temperature Storage temperature Relative humidity 1
Max. Power with 4 sources of video and link at 10Vdc.
200 mA / 12 Vdc 2.2 W 12 to 24 Vac/Vdc ± 15% 100.000 hours 41x106x165 mm 390 gr -40° a 74 °C -55 to 85 °C 95% without condensation
Application:
CONNECTION DIAGRAM MDV6/MD6V STANDALONE
Equipments with this scheme: MDV645X16 and MD6V46X16
WWW.ADILEC.COM E-mail:
[email protected] Tel: +34 93 680 25 13 Fax: +34 93 680 32 29
AUDIO CONNECTOR Pin Description 1 +OUT 1 2 -OUT 1 3 +IN 1 4 +IN 2 5 -IN 2 6 -IN 1 7 +OUT 2 8 -OUT 2
CONTACT CONNECTOR INPUT Pin Description 1 Contact input 2 GND OUTPUT 1 Contact output 2 Contact output
Light signalling description and standard data configuration for MDV6/MD6V standalone format
DATA CONNECTOR Pin Description 1 +RX RS-422/RS-485 2 -RX RS-422/RS-485 3 +TX RS-422/RS-485 4 TX RS-232 5 RX RS232 6 -TX RS-422/RS-485 7 NC 8 GND For RS485 make a bridge between 1-3 (DATA+) and 2-6 (DATA-)
WWW.ADILEC.COM E-mail:
[email protected] Tel: +34 93 680 25 13 Fax: +34 93 680 32 29
Configuration mode To use the MDV6/MD6V configuration mode is necessary a communications software like HyperTerminal or Teraterm. It must be configured with a speed of 19200bps, 8 data bits, no parity, 1 stop bit and disable any flow control. Push the configuration switch during almost 2 seconds to activate the configuration mode, until the configuration led will switched off. Then, when the switch is released, the configuration menu will appear in the HiperTerminal or Teraterm.
MDV6 Configuration menu
The equipment configuration will be modified with the keys from 0 to 9, and the current configuration will appear at the end of the menu. Key 1: Serial channel 1 configuration. With the key 1 we switch the channel 1 configuration between RS232 → RS422 → RS485 → RS485 full duplex Key 2: Serial channel 2 configuration. The same than the last point, but for the 2nd serial channel. Key 3: Channel 1 termination resistor. This enables the 120Ω termination resistor with the RS485 communication mode. With the RS232 communication mode this resistor will remain disabled, and with the RS422 communication mode the resistor will remain enabled. Key 4: Channel 2 termination resistor. The same than the last point, but for the 2nd serial channel. Key 5: Audio channel 1 input configuration. It changes the audio input from unipolar (-IN1 to Ground) to differential input. Key 6: Audio channel 2 input configuration. The same than the last point, but for the 2nd audio channel. Key 7: RS485 Dwell time. It fixes the time the RS485 signal remains active before to change to high impedance after the last write operation in the RS485 bus. We can select the next values: 10µs, 20µs, 50µs, 100µs, 200µs, 500µs, 1000µs y 2000µs. Key 8: Restore default configuration. The default configuration is recovered.
Key 9: Save and Exit. The current configuration is saved and then we leave from the configuration menu. The configuration led is switched on after that. Key 0: Exit and configure remote equipment. The configuration menu of the remote equipment is showed without saving the changes in the local equipment. With this option we can change the remote configuration from the local equipment. We can leave from the configuration menu in three different ways:
With the key 9 “Save and Exit”. Timeout. We have 1 minute available to change the menu configuration. After that time, the equipment leaves itself from the menu configuration. The changes are not saved by this way. Leave from the menu in a manual way. Push the configuration switch almost 3 seconds. The changes are not saved by this way.
ADILEC Enginyeria, S.L. Tel.: +34 93 680 25 13 | Fax: +34 93 680 32 29 e-mail:
[email protected] Francesc Macià, 1 08750 Molins de Rei, Spain www.adilec.com
Rev. 01 January 2015
