Transcript
MEDBIKE® APPLICATION/OPERATION MANUAL 950-192 950-193
FN: 16-181 Rev A 12/16
medBike
This manual covers operation procedures for the following products: 950-192 medBike 950-193 medBike Calf Supports
Contact Information Biodex Medical Systems, Inc. 20 Ramsey Road, Shirley, New York, 11967-4704 Tel: 800-224-6339 (Int’l 631-924-9000) Fax: 631-924-8355 email:
[email protected] www.biodex.com
2
Biodex Medical Systems, Inc. © 2017
Table of Contents Definition of Symbols ................................................................................................................4 Before Proceeding .....................................................................................................................5 Important Safety Information .....................................................................................................6 Biodex Warranty ........................................................................................................................8 1. Introduction ................................................................................................. 10 Intended Use................................................................................................ 10 Indications For Use ....................................................................................... 10 General Cleaning and Maintenance .................................................................. 10 2. Set-up and Operation .................................................................................... 12 Unpackaging and Assembling the medBike ....................................................... 12 Adjusting Pedals on the MedBike ..................................................................... 16 Positioning or Relocating the medBike .............................................................. 17 Display and Handlebars Height Adjustment....................................................... 17 On / Off ....................................................................................................... 17 Changing Pedaling Directions While Exercising .................................................. 19 Spasm Control .............................................................................................. 21 Emergency Stop ........................................................................................... 21 3. Active Modes ................................................................................................ 23 Active Manual Mode ...................................................................................... 23 Active Resistance Mode (Program A) ................................................................ 25 Continuous Watt Mode (Program B) ................................................................. 28 4. Passive Modes .............................................................................................. 31 Passive Manual Mode ..................................................................................... 31 Passive User Profile Mode ............................................................................... 34 Passive Pedal Assisted Mode ........................................................................... 38 5. Specifications ............................................................................................... 42 6. Assembly Drawings and Schematics ................................................................ 43 Calf Support Assembly ................................................................................... 46 Calf Support Assembly ................................................................................... 47
3
Biodex Medical Systems, Inc. © 2017
Definition of Symbols The following symbols and their associated definitions are used and implied throughout this manual.
Symbol
Definition
Carefully read these instructions prior to use Caution General Warning General Mandatory Action Dangerous Voltage “On” Power “Off” Power Earth (ground) Alternating Current Fuse USB Connector/Cable Waste in Electrical Equipment Date of Manufacture Type B Applied Part CE Mark CE Mark for products with EC Certificate Certified for Safety by ETL Intertek
4
Biodex Medical Systems, Inc. © 2017
Before Proceeding NOTE: The warnings, cautions and instructions provided in this manual must be read, followed and kept available for consultation at all times. Observing the information, instructions and procedures presented throughout this manual is essential for using this product both properly and safely. SPECIFIC CAUTIONS ● Allow only qualified, trained personnel to operate or service this product. ● If the equipment is used in a manner other than specified in this operation manual, the protection provided by the equipment may be impaired and results could be compromised. ● Never leave user unattended on device. EN GARDE SPÉCIFIQUES ● Permettez au personnel seulement autorisé, entraîné de faire marcher ou assurer l'entretien de ce produit. ● Si l'équipement est utilisé dans une manière autre qu'indiqué dans ce manuel d'opération, la protection fournie par l'équipement peut être diminuée et les résultats pourraient être compromis. ● Ne quittent Jamais le patient sans surveillance. CAUTION: Unauthorized modifications to this product are not permitted and will void the manufacturer’s warranty. Unauthorized modification of the product may result in a hazard to the user and/or patient. Do not modify this equipment without authorization from the manufacturer. ATTENTION: Les modifications faites sans autorisation à ce produit ne sont pas permises et va faire le vide la garantie du fabricant. La modification faite sans autorisation du produit peut s'ensuivre dans un hasard à l'utilisateur et-ou le patient. Ne modifiez pas cet équipement sans autorisation du fabricant.
Training This operation manual includes assembly and operating instructions. Operating/assembly questions can be directed to the service department during business hours.
5
Biodex Medical Systems, Inc. © 2017
Important Safety Information CAUTION: Federal Law restricts this device to sale by or on the order of a physician, sonographer or other licensed professional. ATTENTION: La Loi Fédérale restreint cet artifice à la vente par ou sur l'ordre d'un docteur, sonographer ou d'autre professionnel agréé. Follow the unpacking and assembly instructions document.
Before using this equipment, read the entire operation manual carefully. Failure to read the manual may result in user error or injury. Be sure to save all provided documents for future reference. Make certain to understand all warning and caution labels as explained in the Before Proceeding section of this manual. This product should be used only as specified in the operation manual.
CAUTION: Biodex devices are designed for use in a client environment. ATTENTION: Artifices Biodex sont conçus pour une utilisation dans un environnement du client. For product specifications, refer to the Table of Contents.
This medical electrical equipment requires special precautions regarding EMC and must be assembled and placed into service according to EMC information provided in this manual. CAUTION: Operation for 950-192: 115 VAC. ATTENTION: Opération pour 950-192: 115 VAC. WARNING: Only use approved power supplies. AVERTISSEMENT: N'utiliser que les alimentations homologuées CAUTION: To avoid risk of electric shock, this equipment must only be connected to supply mains with protective earth. ATTENTION: Pour éviter le risque de choc électrique, cet équipement doit uniquement être connecté à un approvisionnement conduites avec la terre protectrice.
6
Biodex Medical Systems, Inc. © 2017
CAUTION: The plug is considered the method of disconnecting the product from main power. Do not place the product in a position where the plug is not easily accessible. ATTENTION: Le bouchon est considérée comme la méthode de déconnexion du produit d'alimentation. Ne placez pas le produit dans une position où le bouchon n'est pas facilement accessible. CAUTION: This product is intended to remain in one location during operation. It is provided with wheels for relocation which should be used when moving. ATTENTION: Ce produit est destiné à rester à un endroit pendant le fonctionnement. Il est muni de roues pour la réinstallation qui devraient être utilisés lors du déplacement.
7
Biodex Medical Systems, Inc. © 2017
Biodex Warranty 1. Product Warranty A. This equipment and its accessories are warranted by BIODEX MEDICAL SYSTEMS, INC. against defects in materials and workmanship for a period of two years from the date of shipment from BIODEX MEDICAL SYSTEMS, INC. During the warranty period, BIODEX MEDICAL SYSTEMS, INC. will in its sole discretion, repair, send replacement parts or replace the equipment found to have such defects, at no charge to the customer. EXCEPT AS STATED ABOVE, THERE ARE NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION WARRANTIES OR MERCHANTABILITY OR FITNESS FOR USE. BIODEX DOES NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES INCLUDING LOSS OF USE, SALES, PROFITS OR BUSINESS INTERRUPTION. B. This warranty does not apply if the product, as determined by BIODEX MEDICAL SYSTEMS, INC., is defective due to abuse, misuse, modification or service performed by other than a BIODEX MEDICAL SYSTEMS, INC. authorized repair representative. Misuse and abuse include, but are not limited to, subjecting limits and allowing the equipment to become contaminated by fluid materials. C. In order to obtain warranty repair service and to expedite repair process, please contact BIODEX MEDICAL SYSTEMS, INC. Support Services Dept. at 800-224-6339, and select product support as prompted.
2. Warranty is non-transferable 3. Non-Warranty Service A. Repairs and/or replacements not covered by this warranty may be performed by BIODEX MEDICAL SYSTEMS, INC. authorized service representatives. B. The cost of transportation to and from the service location will be the responsibility of the customer.
8
Biodex Medical Systems, Inc. © 2017
Service Procedure If you think you have a service problem, take the following action: 1. Check to see that the problem occurs more than once. 2. Refer to the instruction manual and operations procedure. If you still think you have a service problem, call BIODEX MEDICAL SYSTEMS, INC., Service Department at (800) 224-6339 and select product service as prompted. 1. Keep yourself and the phone next to the equipment. 2. Service will ask you for a brief description of the problem. We will ask specific questions about the malfunction that occurred. This diagnostic process may take a few minutes, so call us when you can set aside an uninterrupted block of time. 3. After taking the information, we will advise on the action we will take. 4. Sometimes service personnel must consult with engineering and it may take time to get back to you. Be sure to let the service representative know your schedule so that we can call at a convenient time. 5. The return call may be from a person other than whom you first reported the problem to. 6. After analyzing the problem, we will decide if the unit can be repaired on site, or replacement parts will be sent. 7. If the unit must be returned, Biodex will provide a return materials authorization number (R.M.A. #.) Pack the table in the carton that it was originally shipped in. It is the customer's responsibility for any damage that occurs during shipping. 8. Non-warranty/non-service contract charges for repair are as follows: a. Materials + b. Time + c. Travel Zone
Contact information Biodex Medical Systems, Inc. 20 Ramsey Road, Shirley, New York, 11967-4704 Tel: 800-224-6339 (Int’l 631-924-9000) Fax: 631-924-8355 email:
[email protected] www.biodex.com 9
Biodex Medical Systems, Inc. © 2017
1. Introduction Intended Use The medBike is designed to provide a safe ergonomic environment for the clinician and customer. The design features are intended to relieve musculoskeletal stress while providing the utmost comfort during exercises.
Indications For Use The medBike is typically used in cardiovascular facilities, skilled nursing facilities, elder care fitness centers, and private practice clinics to achieve quality exercise sessions for a variety of health wellness applications.
General Cleaning and Maintenance 1. As required, cleanse all exterior surfaces and seat pad with a mild detergent solution such as Parker Laboratories Protex Disinfectant or any one-step disinfectant that does not contain bleach. 2. Keep pedal/wheel assemblies free of foreign materials and dirt accumulation. 3. Periodically inspect all welds. 4. Periodically check bolts, tighten if necessary. 5. Periodically inspect pedal strap holders.
10
Biodex Medical Systems, Inc. © 2017
Parts and Adjustments
Figure 1.1. The Biodex medBike parts and adjustments include: Standard Parts and Adjustments: 1. 10" display 2. Non-allergic, high-density grip 3. Telescopic handlebar post, adjustable knob 4. Full metal frame enamel powder, electrostatic spraying 5. Safety pedal with straps 6. Durable transport wheels Optional: 7. Calf Support (950-193)
11
Biodex Medical Systems, Inc. © 2017
2. Set-up and Operation Unpackaging and Assembling the medBike Your medBike will require a minimal amount of assembly. The only tool required is an Allen wrench; provided within the packaged contents.
Figure 2.1. medBike--packaged contents.
Begin by removing the medBike’s main pedal/motor assembly from the packaging. From inside the tube opening (just above the knob), you will see the cable that connects the display to the motor. The cable will have a guide wire that can be used to move the cable up through the handlebar stem tube. When this is complete, place the tube into the pedal/motor assembly opening, and affix the tube with a bolt using the Allen wrench. Use the guide wire to move the display cable up through the handlebar stem tube (Figure 2.2), and use the Allen wrench to affix the handlebar stem tube to the pedal/motor assembly (Figure 2.3).
12
Biodex Medical Systems, Inc. © 2017
Figure 2.2. Use the guide wire to move the display cable up through the handlebar stem tube.
Figure 2.3. Use the Allen wrench to affix the handlebar stem tube to the pedal/motor assembly.
13
Biodex Medical Systems, Inc. © 2017
Figure 2.4. Handlebars stem tube--secured in pedal/motor assembly.
Once the bottom of the handlebars stem tube has be secured, the display can be affixed to the top. But first, the cable must be connected as illustrated below:
Figure 2.5. Connect the display cable.
14
Biodex Medical Systems, Inc. © 2017
Next, line up the holes in the back of the display with the four holes on the top of the handlebars stem tube, and affix the two pieces with the four bolts. Use the Allen wrench to tighten.
Figure 2.6. Connect the display.
The last step is to affix the handlebars to the handlebars stem tube. Line up the holes for the bolts (4) and tighten with the Allen wrench.
Figure 2.7. Connect the handlebars.
15
Biodex Medical Systems, Inc. © 2017
Figure 2.8 Bolts (4) for handlebars.
Adjusting Pedals on the MedBike Managing the degree of hip flexion for certain patients using this device could be a concern. First, consider moving their seat back a few inches. If the seat back reclines, consider that option as well. As for the device itself, the pedal radius is easily changed. Using the Allen wrench, remove pedal bolt and move it into a closer hole on the crank as illustrated in Figure 2.9 below thus reducing the radius of the pedal cranks:
Figure 2.9. Adjusting the Pedals using an Allen Wrench
Or, using the slim wrench included with the medBike, move the pedal to another optional hole on the crank by inserting the wrench between the pedals and the crank as illustrated in the diagrams below and unscrewing the pedal:
16
Biodex Medical Systems, Inc. © 2017
Figure 2.10. Adjusting the Pedals Using the Included Slim Wrench
This method avoids damaging the inner thread of the Allen bolt.
Positioning or Relocating the medBike CAUTION: Before moving the medBike, make sure the power cord is detached. If left attached, the cord plug will rub against the floor as the device is being moved, possibly causing black marks on your flooring. ATTENTION: Avant de déplacer le medBike , faire le cordon d'alimentation est détaché. Si elle reste attachée , la fiche du cordon se frotter contre le sol lorsque le dispositif est déplacé, peut provoquer des marques noires sur votre plancher. The medBike can be easily moved across smooth surfaces. To move the medBike, remove the power cord from the base of the device. Stand behind the device and lift the back end up, pivoting it forward until the front wheels make contact with the floor. Push or pull the device to a new location and set it down gently
Display and Handlebars Height Adjustment The height of the monitor display and handlebars is conveniently adjusted with the hand-turned knob on the front of the device. To raise or lower the display and handlebars, loosen the knob, pull up or down on the handlebars, and re-tighten the knob.
On / Off To turn the device on, press the black switch on the base. 17
Biodex Medical Systems, Inc. © 2017
Figure 2.11. The ON / OFF switch.
Settings If the device is not already set to your preferred language, make your selection on the bottom of the screen (EN = English) and select
.
Figure 2.12 Home screen.
Select either the or setting for your preferred units of measure. Select the maximum number of rotations per minute (rpm) for the Passive Mode. A rotation is the singular event of moving the pedals all the way around a circular motion.
18
Biodex Medical Systems, Inc. © 2017
Figure 2.13. Settings screen.
NOTE: Although there is a “Bluetooth Connection” tab on the Settings screen, that this aspect of the device is not covered in this document.
Changing Pedaling Directions While Exercising The user or clinician may elect at any time during a session to change the pedaling direction from forward to reverse or reverse to forward. It is important to stop pedal movement completely for a few moments while the device mechanisms reset. CAUTION: Stop pedaling when switching between forward to reverse, and vice versa. ATTENTION: Arrêtez de pédaler lors de la commutation entre la marche avant à la
marche arrière, et vice versa.
19
Biodex Medical Systems, Inc. © 2017
Figure 2.14. Warning screen—stop pedaling completely for a moment before reversing direction.
After the warning screen and countdown disappears, press the button to resume the exercise in the new pedaling direction, or press the button to end the exercise.
Figure 2.15. START / STOP screen
20
Biodex Medical Systems, Inc. © 2017
Spasm Control For user safety, the medBike is equipped with a Spasm Control sensor. Medbike spasm control detects sudden twitching and/or rapid pedal movement in opposite directions. If this occurs, pedal movement will gently cease and the screen will display an “Overload!” message. A therapist is able to intervene and decide what action to take.
Figure 2.16. Spasm control warning screen.
NOTE: If pedal rotation is completely resisted in the Passive Mode for a period of time (about a minute), you may see a “Motor over current protection” message. To protect the motor mechanism, the device will suspend operations. When this event occurs, you must turn the device off with the ON / OFF switch at the base, and then turn the power back on.
Emergency Stop The medBike is equipped with an EMERGENCY STOP Button. If, for any reason, a user wants to quickly pause or discontinue an exercise session — be it in Active or Passive Mode — it can be accomplished by pressing the STOP button. To continue exercising, the STOP button must be pressed a second time. You will have the option to resume the session you were in before pressing the STOP button or finishing the session and starting a new one.
21
Biodex Medical Systems, Inc. © 2017
Figure 2.17. Location of Emergency Stop button.
Figure 2.18 Emergency Stop warning screen.
22
Biodex Medical Systems, Inc. © 2017
3. Active Modes Active Manual Mode In the Active Manual Mode, the user of the device is moving the pedals at a constant rate of resistance throughout the exercise. From the Home screen, touch .
Figure 3.1. Home screen.
Select , and set the exercise parameters; total exercise time followed by user weight. When finished, press the button.
Figure 3.2. Active Manual Settings.
23
Biodex Medical Systems, Inc. © 2017
Press +/- to adjust the resistance level for the Forward and/or Reverse directions. The resistance level can be increased or decreased throughout the exercise session, and the pedaling direction can be changed as well. As the user completes each segment, the column representing that segment will turn grey.
Figure 3.3. Active Manual Settings—resistance levels.
If you press the button to stop the exercise, you will see the results data from the workout.
Figure 3.4. Active Manual Mode Results.
Press the button to return to the Home screen.
24
Biodex Medical Systems, Inc. © 2017
Figure 3.5. Home screen.
Active Resistance Mode (Program A) In the Active Program A Mode, the user of the device is moving the pedals at a constant rate during each configured segment of a session. Select .
Figure 3.6. Active Resistance Mode (Program A—exercise time and patient weight settings).
Set total exercise time and enter the user’s weight. Press NEXT. On the Resistance Levels screen, set the resistance for each segment by touching a higher or lower portion of the segment to quickly “ramp up” or “ramp down” that segment. You 25
Biodex Medical Systems, Inc. © 2017
can also touch the orange +/- buttons to adjust the resistance for a particular segment, as well as the pedaling direction. (The segments in Figure 3-7 all happen to show pedaling in the forward direction.) Press the button.
Figure 3.7. Active Resistance Mode (Program A)—resistance level setting screen.
During the session, press the orange +/- buttons to adjust the resistance level for each segment. Alternatively, touch a higher or lower portion of the active segment (the one that has a green or blue trim all the way around) to quickly “ramp up” or “ramp down” that segment. You can also change the pedaling direction by pressing Reverse/Forward.
Figure 3.8. Active Resistance Mode (Program A)—resistance level setting screen (individual segments).
26
Biodex Medical Systems, Inc. © 2017
If you press the button to stop the exercise, you will see the results data from the workout.
Figure 3.9. Active Resistance Mode (Program A) Results.
Press the button to return to the Home screen.
Figure 3.10. Home screen.
27
Biodex Medical Systems, Inc. © 2017
Continuous Watt Mode (Program B) In Active Program B Mode, the level of Watts generated by the user’s pedaling is fixed—instead of the resistance level, as with the Manual and Program A Modes. Because Watts are a function of rpms and resistance level, the two factors will adjust depending on the user’s performance. Therefore, if the user is pedaling quickly and generating a high number of rpms, the resistance level will drop. If the user is producing a small number of rpms, the resistance level will raise proportionately to maintain the designated Watt output. To start a Continuous Watt session, select .
Figure 3.11. Continuous Watt Mode (Program B—exercise time and patient weight settings).
Set total exercise time and enter user weight. Press NEXT. On the next screen, set the Watt level for each segment. Press the button. During the exercise session, your medBike will adjust resistance levels automatically to maintain the programmed WATT zone.
28
Biodex Medical Systems, Inc. © 2017
Figure 3.12. Continuous Watt Mode (Program B)—watt level setting screen (individual segments).
Press +/- to adjust WATT level during the exercise session. The WATT level can remain constant, as illustrated below, or change from segment to segment.
Figure 3.13. Continuous Watt Mode (Program B)—in-session screen.
If you press the button to stop the exercise, you will see the results data from the workout.
29
Biodex Medical Systems, Inc. © 2017
Figure 3.14. Continuous Watt Mode (Program B) Results.
Press the button to return to the Home screen.
Figure 3.15. Home screen.
30
Biodex Medical Systems, Inc. © 2017
4.
Passive Modes
Passive Manual Mode The Passive Manual Mode is used when the user has moderate to severe lower extremity limitations and, therefore, must rely on the device’s motor to rotate the pedals. The rpm level is set prior to the start of the session, and can be adjusted as needed during the exercising. To start a Passive Manual session, select .
Figure 4.1. Home screen—select Passive Mode.
31
Biodex Medical Systems, Inc. © 2017
Set total exercise time, rotations per minute (rpm), and enter the user’s weight. Bodyweight is used for two reasons. The main purpose is to estimate limb size for the spastic detection (overload) algorithm. The second reason is to estimate, using a standard formula, the number of calories burned during the exercise session. (Calorie burn rate will probably not be significant, as the user is seated and the device is assisting with limb movements.) Press the button to begin exercising.
Figure 4.2. Passive Manual Mode— settings screen.
32
Biodex Medical Systems, Inc. © 2017
As the user moves through each segment, the completed segments will turn gray. While the user is exercising, press +/- to adjust rpm level or or to change pedaling direction.
Figure 4.3. Passive Manual Mode—rpm level setting screen (individual segments).
If you press the button to stop the exercise, you will see the results data from the workout.
Figure 4.4. Passive Manual Mode Results.
33
Biodex Medical Systems, Inc. © 2017
Press the button to return to the Home screen.
Figure 4.5. Home screen.
Passive User Profile Mode The Passive User Profile Mode, like the Passive Manual Mode, is used when the user has moderate to severe lower extremity limitations and, therefore, must rely on the device’s motor to rotate the pedals. In the User Profile Mode, the session can be customized into individual segments where the pedaling direction and rpm levels can be set per segment. The rpm level and pedaling direction can also be adjusted as needed during the exercising (while a particular segment is active.) To start a Passive User Profile session, select from the Passive Modes menu.
34
Biodex Medical Systems, Inc. © 2017
Figure 4.6. Passive User Profile Mode— settings screen.
Set total exercise time and enter user weight and select to begin customizing individual segments within the session.
35
Biodex Medical Systems, Inc. © 2017
Touch any individual segment (rectangular boxes in the middle of the screen) to set the rpm and pedaling direction for that particular segment. Press the button to begin exercising.
Figure 4.7. Passive User Profile Mode— rpm levels and pedaling direction settings screen (individual segments).
As the user moves through each segment, the completed segments will turn gray.
Figure 4.8. Passive User Profile Mode—in-progress exercise screen.
36
Biodex Medical Systems, Inc. © 2017
If you press the button to stop the exercise, you will see the results data from the workout.
Figure 4.9. Passive Manual Mode Results.
Press the button to return to the Home screen.
Figure 4.10. Home screen.
37
Biodex Medical Systems, Inc. © 2017
Passive Pedal Assisted Mode Pedal Assisted Mode is different from the other two Passive Modes. The Pedal Assisted Mode is designed for users who have some lower extremity capacity, but still have too many strength and endurance deficits to use one of the Active Modes. The sensors in the medBike will recognize when the user is no longer able to move the pedals without help. The Passive Mode mechanism will activate to maintain a constant rpm level. To start a Pedal Assisted session, select from the Passive Modes menu.
Figure 4.11. Passive Pedal Assisted Mode— settings screen.
Set total exercise time and enter user weight, and press the button.
38
Biodex Medical Systems, Inc. © 2017
Set desired rpm and pedaling direction for each segment. Press the button.
Figure 4.12. Passive Pedal Assisted Mode— rpm settings screen (individual segments).
Start pedaling. After 30 seconds, warm-up medBike will start sensing and compare actual rpm to set rpm. In case actual rpm is 15% lower (or more) than set rpm, medBike will assist user to reach the set rpm. The sensing frequency is modulated in accordance with EXERCISE TIME and SET RPM. Press +/- to adjust rpm.
39
Biodex Medical Systems, Inc. © 2017
Figure 4.13. Passive Pedal Assisted Mode—in-progress exercise screen.
If you press the button to stop the exercise, you will see the results data from the workout.
Figure 4.14. Passive Manual Mode Results.
Press the button to return to the Home screen. 40
Biodex Medical Systems, Inc. © 2017
Figure 4.15. Home screen.
41
Biodex Medical Systems, Inc. © 2017
5. Specifications Dimensions: 26.4." l x 21.7" w x 39.6" h (67 x 55. x 101 cm) Height Adjustable: Telescoping handlebar post Display: 10" TFT touch screen Hand Grips: Non-allergic, high density; telescopic handlebar post Pedals: Fully articulating with heel cup and safety straps Finish: Full metal frame, enamel powder, electrostatic Wheels: Durable transport Speed Control: 1-90 rpm in passive mode Work Rate Range:1-150 watts (100 watts at 90 rpm in Active Mode) Weight: 75 lb (34 kg) Warranty: Two years parts; one year labor
42
Biodex Medical Systems, Inc. © 2017
6. Assembly Drawings and Schematics
43
Biodex Medical Systems, Inc. © 2017
NO.
ITEM NUMBER
Description
1 2 3 4 5 6 7 8 9 10 11 12 12-1 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
355-3-1050-00042 611-6-6203-00 355-6-1055-000 355-6-1056-000 667-5-0170-00 604-4-0050-000 355-6-1057-000 355-6-1058-000 661-2-0080-05 653-1-0080-23 603-3-0084-00 355-4-3000-000 355-6-3002-000 355-6-3003-000 605-3-0063-00 649-1-0060-18 355-6-3004-000 649-1-0080-352 649-1-0080-01 651-2-0080-01 355-4-3005-000 325-6-7538-00 607-3-0053-00 659-1-0050-15 355-6-3014-000 355-6-3015-000 649-1-0080-26 666-1-0100-037 355-6-4000-001 355-6-4001-000 614-1-0050-23 355-6-4002-001 355-6-4003-001 614-1-0050-12 614-1-0050-13 659-1-0060-400 355-4-6000-000 355-3-5001-000 355-3-5004-000 659-1-0050-13 659-1-0060-28 355-3-1000-000 603-3-0084-03 375-6-3018-000 355-6-1011-000 355-6-1012-001 44
Pulley Bearing 6203ZZ (NBK) Spacing tube (Zinc) Spacer (Zinc) C-Clip (Black Nickel) Double round head key Crank: L (Black Nickel) Crank: R (Black Nickel) Hex nut (Zinc) Hex Bolt (Zinc) Spacer (Nickel) Motor Encoder cable Motor bracket (Zinc) Spring ring (Nickel) Hex bolt (Black Zinc) Belt Hex bolt (Zinc) Hex bolt Hex nut (Zinc) Power switch Terminal (Tin) Tooth washer (SUS) Hex oval head bolt (Nickel) Wheel Bracket (Zinc) Stopper bracket (Zinc) Hex bolt (Black Nickel) Shoulder bolt (Black Zinc) Crank cover Label for Crank cover Round head bolt (SUS304) L Housing R Housing Round head bolt (SUS304) Round head bolt (SUS304) Hex oval head bolt (Turning) Console Handlebar stem Handlebar Hex oval head bolt (Nickel) Hex oval head bolt (Nickel) Frame Spacer (Zinc) Rubber Support Cap Tube sleeve
Specification
Ø25xØ17.1x16L Ø25xØ17.1x12L NO.17 5x5x15L 60x25x15 160x25x15 M8x1.25 (10) M8x1.25x40L Ø14xØ8.4x2t 1 190x60x28.07x4t Ø10.5xØ6.3x1.4T M6×1.0×16L 490H8 M8x1.25x20L M8x1.25x35L M8x1.25 19.08x8.1x0.8 10×5.3×0.6t M5x0.8x6L 55x55x25x5t 85x80x45x3t M8×1.25×10 M10x16L 244.58x200x40.09 M5×0.8×10L 599.4x505.13x74.5 599.4x505.13x77.5 M5×0.8×20L M5×0.8×40L M6x1.0x15L (Nickel+Chrome) M5x0.8x16L
Ø18.5xØ8.4x1t Ø20×27(BF3019) (Ø50.8) CO50 80x40x83L
Biodex Medical Systems, Inc. © 2017
Quantity 1 2 1 1 1 2 1 1 2 2 4 1 1 4 4 1 2 1 1 1 1 1 1 1 1 6 2 2 2 4 1 1 10 2 1 1 1 1 4 4 1 2 4 2 1
NO.
ITEM NUMBER
Description
46 47 48 49 50 51 52 52-1 52-2 53 54 55 56 56-1 56-2 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 73-1 74 75 76 77 78 79 80
355-6-1013-001 361-6-9005-00 614-1-0050-26 355-6-1014-000 620-1-0040-00 614-1-0050-08 355-4-1015-000 355-6-1020-000 355-6-1021-000 355-6-1019-000 325-6-7533-00 355-6-1024-000 355-3-2010-00042 355-6-3013-000 355-6-3016-000 355-6-2005-000 611-6-6001-00 355-6-2003-000 355-6-2009-000 666-5-0280-006 603-3-0105-08 659-1-0060-33 355-6-2008-000 651-2-0100-01 355-3-2000-00042 355-6-2006-000 355-6-2004-000 355-6-3051-00042 355-6-3052-001 355-6-3053-000 355-3-3030-000 355-6-3021-000 355-6-3022-000 661-2-0050-00 351-6-2100-00 356-6-9008-000 600-8-0030-00 600-8-0040-00 600-8-0050-00 Carton
45
Adjuster knob Nut Bolt (Zinc) Base plate Self tapping screw (Nickel) Round head screw (Black) EMC circuit board AC cable 1 AC cable 2 Resistor Cable (5) Cable guider Pedal R Velcro (front) Velcro (rear) Bracket (for bearing) Bearing (6001ZZ NTN) Foam bottom base Axle for pedal R (Black) C-Clip (Black Nickel) Spacer (Zinc) Hex bolt Foam for R pedal Hex nut Pedal L Axle for pedal L (Black) Foam for L pedal Transport Wheels Wheel rubbers Plastic bearing Wheel bracket (Zinc) Controller Controller cable Hex nut (Nickel) Power cable EU Power cable USA Allen key 3mm Allen key 4mm Allen key 5mm
Specification
Quantity
Ø81.4x57L USN5x11x17 M5x0.8x12L 270x100x1.8t M4x16L M5x0.8x18L
1 4 5 1 4 4 1 1 1 1 1 1 1 2 2
AC EMC EMC PCB 175L TA11-5 38x350L 38x400L Ø50x22.5L 2 274x114x5t Ø18x47.3L NO.28 10.5×18×1.5t M6x1.0x12L 445x80x5t M10×1.5×4t Ø18x47.3L 445x80x5t 358Lx3t GFM-1012-07
M5x0.8 1.9 M 13A 125V 6 FT 3mm 4mm M5x33x113L
Biodex Medical Systems, Inc. © 2017
4 2 1 2 2 6 1 2 1 1 1 2 2 4 1 1 1 2 1 1 1 1 1 1
Calf Support Assembly
46
Biodex Medical Systems, Inc. © 2017
Calf Support Assembly
47
Biodex Medical Systems, Inc. © 2017
48
Biodex Medical Systems, Inc. © 2017
