Transcript
DVTEL INC. 65 Challenger Road Ridgefield Park, NJ 07660
Meridian Quick Configuration Guide
The contents of this Guide may not be reproduced or reprinted in whole or in part without the express written permission of DVTEL, Inc.
Ver. 1.0
April, 2014
All text and figures included in this publication are the exclusive property of DVTEL Inc., and may not be copied, reproduced or used in any way without the express written permission of DVTEL Inc. Information in this document is subject to change without notice. This document also contains registered trademarks and service marks that are owned by their respective companies or organizations. While reasonable effort was made to ensure that the information in this document was complete and accurate at the time of printing, DVTEL Inc. cannot assure the accuracy of such information. Changes and/or corrections to the information contained in this document may be incorporated into future issues.
FileInfo C:\_Project\6.4.0\PROD_FTCW\BR_MERIDIAN\ Meridian FTCW.pdf created 4/6/2014 11:15
Contents Quick Configuration Guide
Quick Configuration Guide
a
Table of Contents 1 Introduction
1
2 Initial Setup Wizard - Welcome Screen
1
3 Time Setup
2
4 Network Setup
3
5 Video Standards Setup
3
6 Recording Mode Setup
4
7 Exit the Initial Setup Wizard
4
6 8 Admin Center 8.1 Login Screen .........................................................................................................7 8.2 Home Screen .........................................................................................................8 8.3 Admin Center Screen Layout .........................................................................................................9
© 2014 DVTEL
1
Quick Configuration Guide
1
Introduction
Introduction
Meridian Initial Startup Wizard This Help Guide takes you through the Initial Setup Wizard . This guide complements the Meridian Quick Installation Guide.
2
Initial Setup Wizard - Welcome Screen The first time the Meridian NVR is powered up, the user enters the default user name and password. Username: administrator Password: dvtel Once the password has been entered, the system runs the Initial Setup Wizard. The user completes the Wizard, after which the system opens the Meridian Admin Center and the system setup can be continued. Note: All steps in the Initial Setup Wizard are mandatory. The Meridian Admin Center will launch only after completing the Wizard steps.
Wizard Welcome Screen
On the Welcome screen, click Next.
© 2014 DVTEL
Initial Setup Wizard - Welcome Screen
Quick Configuration Guide
3
Time Setup Set the system date and time.
Parameter Date, Time
Set the date and time according to current time now in your region.
Time Zone
Use the dropdown to select your Time Zone.
Daylight Savings Time
When finished, click Next.
© 2014 DVTEL
Notes
Check this box if you are in a location that uses DST.
2
3
Quick Configuration Guide
4
Network Setup
Network Setup
The Network Setup screen is displayed.
Do you want the Meridian Server to automatically set up IP addresses for the cameras on the network (act as DHCP server)? YES/NO. The Meridian Server is already set up with a default IP address. If you want to change it, enter the IP address, subnet mask and default gateway. IMPORTANT NOTE: If the Meridian Server is being connected to the Corporate network where a DHCP server is used, this parameter MUST be set to NO.
5
Video Standards Setup
Select the video standard used in your region: PAL or NTSC. When finished, click Next. © 2014 DVTEL
Quick Configuration Guide
6
Recording Mode Setup
4
Recording Mode Setup Choose the recording mode that cameras attached to the system will follow.
1. Always means cameras will record 24/7. 2. Motion Detection means that cameras will start recording whenever motion is detected at the camera level. The default motion recording settings are 30 seconds pre- and post-motion. This can be changed later on through the Meridian Admin Center. Note: After launching the Meridian Admin Center, it is recommended that the user checks that the motion zone and motion settings (Sensitivity and Threshold), which the system set automatically, are suitable.
When finished, click Next.
7
Exit the Initial Setup Wizard Setup complete After completing the Recording Mode Setup, the Initial Setup Wizard shows the Setup Complete screen.
© 2014 DVTEL
5
Quick Configuration Guide
Exit the Initial Setup Wizard
Setup Complete Up to this point, all the parameters that have been chosen are stored but not yet applied to the system. The user can still review all the settings by using the Back button, and can change any of the settings if required. Setup Complete screen
Once all settings have been reviewed, press the Finish button.
Launching The Initial Setup Wizard will apply all the chosen parameters and launch the application in the background. This process takes 2-3 minutes, during which the ‘Launching’ screen is displayed. Launching Meridian screen
© 2014 DVTEL
Exit the Initial Setup Wizard
Quick Configuration Guide
6
Launch Completed When the system is ready, the Launch Completed message is shown.
Launch Completed screen
You can then click on Launch Admin Center to continue with the remaining setup activities.
8
Admin Center The Meridian Admin Center allows the user to configure all aspects of the system camera settings, recording schedule, user management, etc. To launch the Meridian Admin Center (if not already launched from the wizard), click on the application shortcut icon on the Desktop.
© 2014 DVTEL
7
Quick Configuration Guide
8.1
Login Screen
Parameter
Admin Center
Notes
User name
‘admin’ is the user name for the default System Administrator user
Password
For first-time use, no password is defined. If desired, you can set a password from the Users page
Server IP / Hostname
Enter the Server IP address as set in the Initial Setup Wizard. If you did not change the IP address, the default is 192.168.50.10 or enter localhost.
When the user’s credentials have been accepted, the Meridian Admin Center opens and displays the Home screen.
© 2014 DVTEL
Quick Configuration Guide
8.2
Admin Center
8
Home Screen The Home Screen is always displayed when the Meridian Admin Center starts up. The user can navigate from the Home screen to any desired page and then return to it by clicking the Home button on the sidebar.
The current version number is displayed in the bottom right-hand corner of the screen. A link allows the user to check whether a newer version of the application is available. After the first launch, a dialog is displayed with the current system information. This shows the user that system storage has been configured, and all cameras have been discovered and attached to the system.
© 2014 DVTEL
9
Admin Center
Quick Configuration Guide
To conclude the setup, we recommend you to carry out the following steps: 1. Name the cameras, changing their default names to names which suit your site. 2. Add users if needed and assign them to one of the default user groups or alternatively create a custom user group if the default ones don’t suit your needs. While not necessary, you can continue setting up advanced settings of the system. You can simply follow the steps listed under the Advanced Settings or access more options by using the Sidebar and accessing the relevant pages. We recommend that you print out the Sign-Off report for the customer to sign before leaving site. This report details how the system has been configured.
8.3
Admin Center Screen Layout
The Meridian Admin Center layout is divided roughly into 3 sections, the Sidebar, the Item list and the Settings page. Please refer to the below table for more detailed information Field
1. SideBar
Description Home, System, Cameras, Users, Rules and Alarms - The Admin Center pages are grouped into categories. Clicking any of these in the sidebar will place a list of items associated with that category into the item list.
© 2014 DVTEL
Admin Center
Quick Configuration Guide
Field
10
Description
2. Item List
For any selected category in the Sidebar, the available items are listed. The required item can be selected and its name is then highlighted.
3. Settings Page
The layout of the settings page varies according to the selection made in the item list.
4. Help Button
The system has an extensive context-sensitive Help function. In any screen, clicking the ‘Help’ button opens a page of information about that screen , with specific information such as explanations about icons used, how to add, edit or delete entries, default values, cautions and notes where required
Even after the initial configuration, you can easily fine tune and change the default settings. As noted, extensive Help system is embedded within the application. Additionally, you can always access the DVTEL website to download and watch the various tutorials explaining about the Meridian product.
© 2014 DVTEL
