Transcript
Side 2
8
9
Second Processor Air Baffle Modification
Install Processor Air Duct
Front Panel Connectors and Indicators
To Configure Processor Air Baffle for Two Processors: Note: This step only applies if your system has two processors. If only one processor is installed, leave the air baffle in place and proceed to Step 9.
I
Second Processor Air Baffle ... remove only if system has two processors.
CAUTION: For a one-processor configuration, the air baffle must remain in place to ensure proper cooling.
A
H
Install processor air duct as shown. A
A. USB Ports B. Video Port C. I/O 1 and I/O 2 Activity LEDs
A
Remove air baffle by rocking back and forth until it breaks off.
1
I/O
B
C
D
E
F
G
D. NIC1 and NIC2 Activity LEDs E. Disk Activity LED F. ID LED
G. Power Button H. Fault LED I. Power LED
2 1 2
ID
Component Layout
Install Mezzanine Card
Midplane Power Connector
Hold mezzanine card by its edges and remove from packaging. Remove protective connector cover from mezzanine card.
C
With a 1/4-inch nut driver, install the four standoffs that shipped with the mezzanine card in the same holes that were just vacated by the screws.
BIOS Bank Select 3
2
Default BOOT FROM EMERGENCY BIOS IMAGE
With a Phillips* screwdriver, remove the four screws on the server board.
Mezzanine Card Connector
J3A3
SAS Controller
PASSWORD CLR
I/O
DIMM D2
DIMM D1
DIMM C1
J4A1 1
DIMM C2
CLEAR PASSWORD
3
DIMM B1
Default
2
DIMM B2
B
B
C
DIMM A1
A
Midplane Signal Connector
DIMM A2
10
2 1 2
11
I/O I/O
22
ID
11 22
BMC Force Update
IDID
2
3
Enabled Default Disabled
D
E
Position mezzanine card above mezzanine card socket and align the four holes with standoffs. Carefully press mezzanine card into place until it is fully seated in the socket and resting on the standoff supports.
Intel® 6321ESB I/O Controller Hub
J7A1
Secure mezzanine card to standoffs with the four screws previously removed.
Intel® 5000P Memory Controller Hub (MCH)
CMOS CLR
E
3
2
D
Battery
CLEAR Default CMOS
J1F2
1 1
I/O
2
I/O
CPU 1 Socket
CPU 2 Socket
2 1 2
1 2
ID
ID
CPU Voltage Regulator
USB1
11
Install Top Cover
Align top cover over corresponding notches in module chassis. Slide top cover forward to close.
See your Intel® Compute Module MFS5000SI User Guide for expanded component and connection information. Diagnostic LED Information LED Name Power LED
Fault LED
1
I/O
2 1 2
Function
Color
Identifies power state of system
Green
Off = Power off On = Power on Slow blink = Standby or sleep mode
Amber
Off = No fault On = Critical error or non-recoverable Slow blink = Non-critical Fast blink = Locate Double blink = Degraded state
Identifies fault warning
ID LED
Identifies server compute module
Indicator
Blue
Use Intel® Modular Server Control UI to turn ID LED on or off
Drive Activity LED
Indicates drive activity
Green
Off = No drive activity Blink = Drive activity
NIC1-NIC2 Activity LEDs
Indicates network activity and link
Green
Off = No link On = Link established Blink = Activity
I/O 1 and I/O 2 Activity LEDs
Indicates network activity and link of NICs on mezzanine card
Green
Off = No link On = Link established Blink = Activity
ID
Optional Accessories and Order Codes Dual Gigabit Ethernet I/O Expansion Mezzanine Card
AXXGBIOMEZ
A complete list of accessories and spares can be found at: www.intel.com/go/serverbuilder
USB2
Video
Drive ID I/O 1 NIC1 Activity LED LED LED Power I/O 2 NIC2 LED Button LED LED
Power/Fault LEDs
