Mgp Eu

Transcript

Compact Guide Cylinder Series MGP ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 CL MLG CNA CNG MNB CNS CLS CB CV/MVG CXW CXS CXT MX MXU MXH MXS MXQ MXF MXW MXP MG MGP MGQ MGG MGC MGF New end lock type introduced to Series MGP MGZ CY MY 3.22-1 Compact Guide Cylinder Series MGP ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 Piping is possible from two directions Four mounting types provided 1. Top mount • Easy positioning Knock pin holes provided on each mounting surface 1. Top ports 2. Side mount 1. T op m oun t 3. T-slot side mount Easy adjustment of work piece and cylinder mounting 1. T op p orts 4. Bottom mount 2. Side ports 1. A uto swi tch mo unt ing de Si 2. s rt po om ott B 4. t un mo Auto switches can be mounted on two sides 2. A uto swi tch 3. T mo -slo unt t si ing de mo unt Two types of guide rod bearing to 2. S ide mo unt • accommodate various applications Slide bearing The withstood lateral load is more than twice that of a conventional stopper cylinder (round bar type), and is suitable for use with lateral loads accompanied by impact, as in stoppers. Ball bushing Suitable for use as a pusher and lifter. • Long strokes up to 400mm standardised.
Stroke Variations Bearing type MGPM Slide bearing MGPL Ball bushing 3.22-2 Bore size (mm) Stroke (mm) 25 Intermediate strokes 40 50 75                       20               25    20 12  16  Order made 100 125 150 175 200 250 300 350 400 30 10            32             40             50             63             80             100             Spacer type available in stroke increments of 1mm & 5mm. Special body type (-XB10) available in stroke increments of 1mm. 1. Intermediate stroke (using special body) 2. With air cushion/Intermediate stroke (spacer type) 3. Heat resistant cylinder 4. Low speed cylinder 5. Fluoro rubber seals 6. With heavy duty scraper New 7. With coil scraper New 8. Variable stroke cylinder Adjustable extension type New 9. Variable stroke cylinder Adjustable retraction type New 10. Stainless steel piston rod & plate, etc. ew N • End lock type introduced Holds the cylinder's home position even if the air supply is cut off. Compact body length is only 25mm longer than standard.
Stroke Variations Bore size (mm) Bearing type 20 25 32 40 50 63 80 100 MGPM Slide bearing MGPL Ball bushing Intermediate Locking strokes direction Stroke (mm) 25 50 75                         CL Manual release MLG 100 125 150 175 200 250 300 350 400                                                                         CNA Spacer Front lock Non-locking type type available in 5mm stroke Rear lock Locking increments. type CNG MNB CNS CLS CB • Air cushion type standardized • An air cushion has been added to the compact guide cylinder to suppress vibration and noise at the stroke end. It can absorb nearly three times as much kinetic energy as a rubber bumper. CV/MVG
Stroke Variations Bearing type Cushion valve is built into the body MGPM Slide bearing MGPL Ball bushing Bore size (mm) 16 20 25 32 40 50 63 80 100 Stroke (mm) 25 50 75                          Intermediate strokes                                  CXS         Strokes available in 1mm increments by changing the collar. Bore size (mm) (Compared with MGPM50 compact guide cylinder) MGPS Bore size (mm) Guide rod diameter (mm) MGPS MGPM 50 30 25 80 45 30 Bearing type MGP Cushion 25 50 75       100 125 150 175 200           MXF MXW MXP With air cushion Rubber bumper Air cushion • Copper-free (20-) Ball bushing With end lock Rubber bumper MGP Heavy duty guide rod type Slide bearing MGP 12 16 20 25 32 40 50 63 80 100 • Clean room series: ø12 to ø63 • Water resistant type: ø20 to ø100 Note) • Copper-free specification: ø12 to ø100 Slide bearing MGPS MXQ Stroke (mm) Bore size (mm) Standard type MGP MXS MG
Series Variations Series Slide bearing 50 80 MX MXH
Stroke Variations Bearing type CXT MXU • Heavy duty guide rod type with improved load resistance • Lateral load resistance: 10% increase • Eccentric load resistance: 25% increase • Impact load resistance: 140% increase CXW 100 125 150 175 200 Note) Available with ø20 to ø100 slide bearing type only MGQ MGG MGC MGF MGZ CY Rubber bumper MY 3.22-3 3.22-4 Compact Guide Cylinder Series MGP ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 How to Order CL MLG Compact Guide Cylinder 30 MGP M 25 Z73 CNA CNG MNB Number of auto switches Compact guide cylinder 2 pcs. 1 pc. Nil S CNS Bearing type M L CLS Slide bearing Ball bushing Auto switch type Without auto switch (built-in magnet cylinder) Nil ∗ Refer to the table below for auto switch model numbers. CB CV/MVG Bore size 12 16 20 25 32 12mm 16mm 20mm 25mm 32mm 40 50 63 80 100 Cylinder stroke (mm) 40mm 50mm 63mm 80mm 100mm CXW Refer to the standard stroke table on page 3.22-6. CXS Thread Port (ø20 to ø100) CXT Rc(PT) TF MX G(PF) MXU MXH Applicable auto switches Load voltage Type Reed switch Special function Electrical Indicator entry light Wiring (output) DC 3 wire — 2 wire 24V Lead wire length (m) Auto switch model Electrical entry direction 0.5 3 5 Perpendicular (Nil) (L) (Z) In-line MXS Applicable load 5V — — Z76   — IC circuit 12V 100V — Z73    — 5V 12V 100V or less — Z80   — IC circuit Y69A Y59A    Y7PV Y7P    Y69B Y59B    Y7NWV Y7NW    Y7PWV Y7PW    Y7BWV Y7BW    — Y7BA —   — P5DW —   MXQ — Yes — Grommet No 3 wire (NPN) 5V 12V 3 wire (PNP) — 2 wire Solid state switch AC Note 1) Diagnostic indication (2 colour indicator) Grommet Yes 3 wire (NPN) 3 wire (PNP) 12V 24V 5V 12V — MXF Relay, PLC MXP IC circuit MG — IC circuit MGP Relay, PLC Magnetic field resistant (2 colour indicator) 2 wire Note 3) — MGQ MGG 12V Water resistant (2 colour indicator) MXW MGC — MGF Note 1) Lead wire symbols 0.5m ...... Nil (Example) Y69B 3m ......... L Y69BL 5m ......... Z Y69BZ Note 2) Solid state auto switches marked with a "" are produced upon receipt of order. Note 3) Type D-P5DW cannot be mounted on bore sizes of ø32 or less. MGZ CY MY 3.22-5 Series MGP Specifications Double acting Action Air 1.5MPa Fluid Proof pressure 1.0MPa Maximum operating pressure Minimum operating pressure ø20 to ø100 0.1MPa ø12 to ø63 –10 to 60° C (with no freezing) 50 to 500mm/s Ambient and fluid temperature Piston speed 0.12MPa ø12, ø16 ø80, ø100 Cushion 50 to 400mm/s Rubber bumper at both ends Lubrication Non-lube Stroke length tolerance +1.5 0 mm Standard Strokes Standard stroke (mm) 10, 20, 30, 40, 50, 75, 100, 125, 150, 175, 200, 250 Bore size (mm) 12, 16 20, 30, 40, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400 20, 25 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400 32 to 100 Manufacture of Intermediate Strokes Modification method Spacer installation type Spacers are installed in a standard stroke cylinder. • ø12 to 32 : Available in 1mm stroke increments • ø40 to 100 : Available in 5mm stroke increments Part number Refer to standard part numbers and ordering procedure. Applicable stroke (mm) Indicate -XB10 at the end of the standard model no. Refer to P.52 for order made specifications. ø12, ø16 1 to 249 ø12, ø16 11 to 249 ø20, ø25, ø32 1 to 399 ø20, ø25 21 to 399 ø40 to ø100 5 to 395 ø32 to ø100 26 to 399 Part no.: MGPM20—39 A spacer 1mm in width is installed in a MGPM20—40. C dimension is 77mm. Example Special body type (-XB10) A special body is manufactured for the specified stroke. • All bore sizes are available in 1mm increments. Part no.: MGPM20—39—XB10 Special body manufactured for 39mm stroke. C dimension is 76mm. Note) The minimum stroke for mounting auto switches is 10mm or more for two switches, and 5mm or more for one switch. Auto switch mounting bracket part no. for D-P5DW Bore size (mm) Mounting bracket part no. Theoretical Output OUT Notes Switch mounting bracket Hexagon socket head cap screw 40, 50, 63, (M2.5 x 8 l ) 2 pcs. BMG1-040 80, 100 Hexagon socket head cap screw (M3 x 16 l ) 2 pcs. Spring washer (nominal size 3) (N) Bore size Rod Operating Piston area size direction (mm) (mm) (mm²) 12 16 20 25 32 40 50 63 80 100 6 8 10 12 16 16 20 20 25 30 Operating pressure (MPa) 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 113 OUT 113 23 34 45 57 68 79 90 102 IN 85 17 26 34 43 51 60 68 77 85 OUT 201 40 60 80 101 121 141 161 181 201 IN 151 30 45 60 76 91 106 121 136 151 OUT 314 63 94 126 157 188 220 251 283 314 IN 236 47 71 94 118 142 165 189 212 236 OUT 491 98 147 196 246 295 344 393 442 491 IN 378 76 113 151 189 227 265 302 340 378 OUT 804 161 241 322 402 482 563 643 724 804 IN 603 121 181 241 302 362 422 482 543 603 OUT 1257 251 377 503 629 754 880 1006 1131 1257 634 739 IN 1056 211 317 422 528 OUT 1963 393 589 785 982 1178 1374 1570 1767 1963 660 825 845 950 1056 IN 1649 330 495 OUT 3117 623 935 1247 1559 1870 2182 2494 2805 3117 561 841 1121 1402 1682 1962 2242 2523 2803 IN 2803 OUT 5027 990 1154 1319 1484 1649 1005 1508 2011 2514 3016 3519 4022 4524 5027 IN 4536 907 1361 1814 2268 2722 3175 3629 4082 4536 OUT 7854 1571 2356 3142 3927 4712 5498 6283 7069 7854 IN 7147 1429 2144 2859 3574 4288 5003 5718 6432 7147 Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm²) 3.22-6 IN Compact Guide Cylinder Series MGP Weights Slide bearing: MGPM12 to 100 (kg) Standard stroke (mm) Bore size (mm) Model 10 20 25 30 40 50 75 100 125 150 175 200 250 300 350 400 12 MGPM12 0.24 0.28 0.39 0.50 0.59 0.70 — 0.53 0.97 1.60 — — — MGPM20 — 0.67 — 0.75 0.91 0.68 1.17 0.80 20 0.48 0.83 0.98 1.35 — 0.38 0.89 1.22 — 0.33 0.79 1.09 1.17 MGPM16 0.31 0.43 0.35 16 — — 1.37 1.57 1.76 1.96 2.16 2.63 3.03 3.42 3.82 CL 25 MGPM25 — 0.95 1.05 1.16 1.27 1.65 1.92 2.19 2.47 2.74 3.01 3.67 4.21 4.76 32 MGPM32 — — — 1.69 — — 2.07 2.47 2.85 3.24 3.62 4.00 4.38 5.33 6.09 6.86 5.30 7.62 MLG 40 MGPM40 — — 1.95 — — 2.37 2.83 3.25 3.68 4.10 4.53 4.95 5.99 6.85 7.70 50 MGPM50 — — 3.36 — — 4.00 5.37 6.01 6.65 7.29 7.93 9.54 — — 4.73 5.78 6.54 7.29 8.05 8.80 — — 8.67 9.61 — — 63 MGPM63 — — 4.18 80 MGPM80 — — 6.49 100 MGPM100 — — 10.5 4.94 7.43 11.9 13.6 14.9 9.56 10.8 12.1 8.55 13.4 11.4 12.9 11.5 12.4 13.4 15.8 17.7 14.4 19.5 15.9 10.5 16.3 17.6 18.9 20.2 23.6 26.2 28.9 31.5 21.4 Ball bushing: MGPL12 to 100 (kg) Model 10 20 25 30 40 50 75 100 125 150 175 200 250 300 350 400 12 MGPL12 0.24 0.27 — 0.35 0.39 0.47 0.56 0.66 — 0.39 — 0.51 0.93 1.50 — — — MGPL20 — 0.70 — 0.77 0.89 0.67 1.14 0.79 20 0.56 0.97 0.91 1.28 — 0.34 0.83 1.16 — MGPL16 0.74 1.04 1.08 16 0.30 0.43 1.31 1.52 1.69 1.87 2.04 2.42 2.77 3.12 3.47 25 MGPL25 — 0.98 — 1.07 1.25 1.34 1.57 1.81 2.08 2.31 2.54 2.77 3.27 3.74 4.20 4.66 32 MGPL32 — — 1.54 — — 1.85 2.30 2.62 2.99 3.31 3.94 4.63 5.26 5.89 6.52 40 MGPL40 — — 1.79 — — 2.15 2.64 3.00 3.42 3.78 3.62 4.14 4.50 5.28 6.00 50 MGPL50 — — 3.11 — — 3.66 4.41 4.96 5.60 6.15 6.70 7.25 8.48 9.57 63 MGPL63 — — 3.93 — — 4.59 5.46 6.12 80 MGPL80 — — 6.25 — — 8.69 9.51 100 MGPL100 — — 9.89 — — 7.39 11.6 13.4 14.5 7.54 6.88 8.21 8.87 6.72 7.44 10.7 11.8 10.3 11.7 13.0 14.3 10.3 11.1 12.0 12.8 14.7 16.3 18.0 19.6 15.7 16.9 18.1 19.3 21.9 24.2 26.6 28.9 Torque: T (N⋅ m) T (N⋅ m) 20 25 32 40 50 63 80 100 CNS Stroke (mm) For non-rotating accuracy θ without load, use a value no more than the values in the table as a guide. Bore size (mm) Bearing type 10 MGPM 0.39 0.32 — 0.27 0.24 0.21 0.43 0.36 0.31 0.27 0.24 0.22 0.19 — — — 12 MGPL 0.61 0.45 — 0.35 0.58 0.50 0.37 0.29 0.24 0.20 0.18 0.16 0.12 — — — 16 MGPM 0.69 0.58 — 0.49 0.43 0.38 0.69 0.58 0.50 0.44 0.40 0.36 0.30 — — — 20 MGPL 0.99 0.74 — 0.59 0.99 0.86 0.65 0.52 0.43 0.37 0.32 0.28 0.23 — — — 25 20 25 30 40 50 75 100 125 150 175 200 250 300 350 400 MGPM — 1.05 — 0.93 0.83 0.75 1.88 1.63 1.44 1.28 1.16 1.06 0.90 0.78 0.69 0.62 32 MGPL — 1.26 — 1.03 2.17 1.94 1.52 1.25 1.34 1.17 1.03 0.93 0.76 0.65 0.56 0.49 40 MGPM — 1.76 — 1.55 1.38 1.25 2.96 2.57 2.26 2.02 1.83 1.67 1.42 1.24 1.09 0.98 50 MGPL — 2.11 — 1.75 3.37 3.02 2.38 1.97 2.05 1.78 1.58 1.41 1.16 0.98 0.85 0.74 63 MGPM — — 6.35 — — 5.13 5.69 4.97 4.42 3.98 3.61 3.31 2.84 2.48 2.20 1.98 80 MGPL MGPM — — 5.95 — — 4.89 5.11 4.51 6.34 5.79 5.33 4.93 4.29 3.78 3.38 3.04 100 — — 7.00 — — 5.66 6.27 5.48 4.87 4.38 3.98 3.65 3.13 2.74 2.43 2.19 MGPL — — 6.55 — — 5.39 5.62 4.96 6.98 6.38 5.87 5.43 4.72 4.16 3.71 3.35 MGPM — — — — 8.60 7.86 7.24 6.24 5.49 4.90 4.43 MGPL — — — — 7.62 9.83 8.74 11.6 10.7 9.12 7.95 7.02 6.26 5.63 MGPM — — 14.7 — — 12.1 13.5 11.9 10.7 8.16 7.04 6.19 5.52 4.99 MGPL — — 10.2 — — 8.84 7.80 6.94 6.24 MGPM — — 21.9 — MGPL — — 15.1 — MGPM — — 38.8 MGPL — — 27.1 13.0 9.17 CLS CB CV/MVG CXW CXS CXT MXU +θ –θ 16 MNB Non-rotating Accuracy of Plate MX Allowable Rotational Torque of Plate 12 CNG Standard stroke (mm) Bore size (mm) Bore size (mm) CNA 10.8 12.0 10.6 8.48 11.0 9.50 9.83 9.69 8.86 9.74 13.0 11.9 11.0 10.2 — 18.6 22.9 20.5 18.6 17.0 15.6 14.5 12.6 11.2 10.0 9.11 — 23.3 22.7 20.6 18.9 17.3 16.0 14.8 12.9 11.3 10.0 8.94 — — 33.5 37.5 33.8 30.9 28.4 26.2 24.4 21.4 19.1 17.2 15.7 — — 30.6 37.9 34.6 31.8 29.3 27.2 25.3 22.1 19.5 17.3 15.5 Non-rotating accuracy θ MGPM MGPL MXH MXS MXQ MXF ±0.08° ± 0.10° MXW ±0.07° ± 0.09° MXP ±0.06° ± 0.08° MG ±0.05° ± 0.06° MGP ±0.04° ± 0.05° MGQ MGG MGC MGF MGZ CY MY 3.22-7 Series MGP Model Selection Selecting Conditions Vertical Horizontal l l m Mounting orientation m Maximum speed (mm/s) Graph (Slide bearing) Graph (Ball bushing) 200 400 200 400 1, 2 3, 4 13, 14 15, 16 5 to 8 9 to 12 17, 18 19, 20 Selection Example 1 (Vertical Mounting) Selection Example 2 (Horizontal Mounting) Selecting conditions Mounting: Vertical Bearing type: Ball bushing Stroke: 30mm Maximum speed: 200mm/s Load weight: 3kg Eccentric distance: 90mm Find the point of intersection for the load weight of 3kg and the eccentric distance of 90mm on graph 5 , based on vertical mounting, ball bushing, 30mm stroke, and the speed of 200mm/s. → MGPL25-30 is selected. Selecting conditions Mounting: Horizontal Bearing type: Slide bearing Distance between plate and load center of gravity: 50mm Maximum speed: 200mm/s Load weight: 2kg Stroke: 30mm Find the point of intersection for the load weight of 2kg and stroke of 30mm on graph 13 , based on horizontal mounting, slide bearing, the distance of 50mm between the plate and load center of gravity, and the speed of 200mm/s. → MGPM20-30 is selected. 5 Less than 40mm stroke V = 200mm/s 13 l = 50mm V = 200mm/s 20 50 ø100 ø100 ø80 10 ø80 ø25 ø20 10 5 ø50, 63 ø50, 63 ø32, 40 ø32, 40 ø25 Load weight m (kg) Load weight m (kg) ø16 ø12 1 ø20 5 ø25 ø20 ø16 ø12 ø16 1 ø12 0.1 0.1 10 50 100 Eccentric distance l (mm) 3.22-8 200 10 20 30 40 50 51 Stroke (mm) 100 200 300 Compact Guide Cylinder Vertical Mounting Series MGP Operating pressure: 0.4MPa Operating pressure: 0.5MPa or more Slide Bearing MGPM12 to 100 1 50mm stroke or less 2 Over 50mm stroke V = 200mm/s 300 Load weight m (kg) 100 200 ø100 ø80 ø100 CL ø80 100 ø63 ø63 ø50 ø50 ø40 ø40 ø32 ø32 CNG ø25 MNB Load weight m (kg) 200 V = 200mm/s 300 10 ø25 ø20 5 ø16 10 MLG CNA ø20 CNS 5 ø16 CLS ø12 ø12 1 CB 1 CV/MVG CXW CXS 0.1 0.1 10 50 100 200 10 50 Eccentric distance l (mm) 3 50mm stroke or less 100 200 MX Eccentric distance l (mm) 4 Over 50mm stroke V = 400mm/s 100 MXU V = 400mm/s 100 ø100 MXH ø100 50 MXS 50 ø80 ø80 ø63 ø63 CXT MXQ MXF ø50 ø50 10 10 MXW Load weight m (kg) Load weight m (kg) ø40 5 ø32 ø25 ø40 MXP 5 ø32 MG ø25 MGP ø20 MGQ ø20 1 1 ø16 MGG ø16 MGC ø12 MGF ø12 MGZ 0.1 0.1 10 50 100 Eccentric distance l (mm) 200 10 50 100 200 CY Eccentric distance l (mm) MY 3.22-9 Series MGP Vertical Mounting Operating pressure: 0.4MPa Operating pressure: 0.5MPa or more Ball Bushing MGPL12 to 25 5 30mm stroke or less 6 Over 30mm stroke V = 200mm/s 20 V = 200mm/s 20 10 10 ø25 ø20 5 5 ø25 ø20 Load weight m (kg) Load weight m (kg) ø16 ø12 1 0.1 ø16 1 ø12 0.1 10 50 100 200 10 50 Eccentric distance l (mm) 100 200 Eccentric distance l (mm) MGPL32 to 100 7 50mm stroke or less 8 Over 50mm stroke V = 200mm/s 300 V = 200mm/s 300 ø100 ø100 ø80 100 100 ø80 ø63 50 ø50 Load weight m (kg) Load weight m (kg) 50 ø40 ø32 10 ø63 ø50 ø40 10 ø32 5 5 1 1 1 5 10 Eccentric distance l (mm) 3.22-10 100 200 10 50 100 Eccentric distance l (mm) 200 Compact Guide Cylinder Vertical Mounting Ball Bushing Series MGP Operating pressure: 0.4MPa MGPL12 to 25 9 30mm stroke or less 10 Over 30mm stroke V = 400mm/s 10 1 5 0.5 V = 400mm/s CL ø25 MLG CNA ø20 CNG ø20 Load weight m (kg) Load weight m (kg) ø25 1 ø16 ø16 MNB 0.1 CNS CLS CB ø12 CV/MVG ø12 CXW CXS 0.01 0.1 10 50 100 200 10 50 100 200 Eccentric distance l (mm) Eccentric distance l (mm) CXT MX MGPL32 to 100 MXU 11 50mm stroke or less 12 Over 50mm stroke V = 400mm/s 100 V = 400mm/s 100 MXH 50 MXS ø100 50 MXQ ø80 ø100 MXF ø80 ø63 MXW Load weight m (kg) Load weight m (kg) 10 ø50 10 ø40 ø63 MXP 5 MG ø50 MGP ø40 MGQ 5 ø32 MGG 1 MGC ø32 MGF 1 MGZ 0.2 10 50 100 Eccentric distance l (mm) 200 10 50 100 200 CY Eccentric distance l (mm) MY 3.22-11 Series MGP Horizontal Mounting Slide Bearing MGPM12 to 100 14 l = 100mm V = 200mm/s 13 l = 50mm V = 200mm/s 50 50 ø100 ø100 ø100 ø80 ø100 ø80 ø80 ø80 ø50, 63 ø50, 63 ø32, 40 ø32, 40 ø50, 63 ø50, 63 ø32, 40 10 10 ø32, 40 ø25 ø25 ø20 ø20 5 Load weight m (kg) Load weight m (kg) 5 ø25 ø20 ø16 ø16 ø12 1 ø25 ø20 ø16 ø12 1 ø16 ø12 ø12 0.1 0.1 10 20 30 40 50 51 100 200 300 10 20 30 Stroke (mm) 40 50 51 100 200 300 200 300 Stroke (mm) 16 l = 100mm V = 400mm/s 15 l = 50mm V = 400mm/s 50 50 ø100 ø100 ø80 ø100 ø100 ø80 ø63 ø63 ø50 ø50 ø40 ø40 ø80 ø80 ø50, 63 ø50, 63 10 5 ø32 ø40 ø40 Load weight m (kg) Load weight m (kg) 10 ø32 ø25 ø25 ø20 5 ø32 ø32 ø20 ø25 ø25 ø20 ø20 ø16 ø16 1 1 ø16 ø16 ø12 ø12 ø12 ø12 0.1 10 0.1 20 30 40 50 51 Stroke (mm) 3.22-12 100 200 300 10 20 30 40 50 51 Stroke (mm) 100 Compact Guide Cylinder Series MGP Ball Bushing Horizontal Mounting 17 l = 50mm V = 200m/s 18 l = 100mm V = 200m/s MGPL12 to 25 MGPL12 to 25 10 10 ø25 ø20 5 ø25 ø16 ø20 ø16 ø12 ø20 ø25 CNA ø20 ø16 CNG ø16 ø16 ø12 MNB ø16 ø12 1 MLG ø20 Load weight m (kg) Load weight m (kg) ø25 ø20 CL ø25 5 ø25 1 ø12 0.5 CNS ø12 ø12 CLS 0.5 10 20 30 31 50 100 101 200 300 10 20 30 31 50 Stroke (mm) 100 101 200 300 CB Stroke (mm) MGPL32 to 63 CV/MVG MGPL32 to 63 50 50 CXW Load weight m (kg) Load weight m (kg) CXS ø50, 63 ø50, 63 ø50, 63 ø32, 40 ø32, 40 ø32, 40 10 CXT ø50, 63 MX ø50, 63 MXU ø32, 40 MXH 10 ø50, 63 ø32, 40 MXS ø32, 40 5 MXQ 5 10 20 30 40 50 51 100 101 200 300 10 20 30 40 50 51 100 101 200 300 MXF Stroke (mm) Stroke (mm) MXW MGPL80, 100 MGPL80, 100 50 50 MXP ø100 ø100 ø80 Load weight m (kg) Load weight m (kg) ø100 ø100 ø80 ø80 10 MG MGP ø100 ø80 ø80 MGQ ø100 MGG MGC 10 ø80 MGF 5 MGZ 5 10 20 29 30 49 50 Stroke (mm) 100 200 300 10 20 29 30 49 50 100 200 300 CY Stroke (mm) MY 3.22-13 Series MGP Ball Bushing Horizontal Mounting 19 l = 50mm V = 400m/s 20 l = 100mm V = 400m/s MGPL12 to 25 MGPL12 to 25 5 ø25 ø25 ø25 ø20 ø20 ø20 ø16 ø16 ø25 ø25 ø20 ø20 ø16 ø16 ø16 ø12 ø12 ø12 ø25 Load weight m (kg) Load weight m (kg) 5 ø16 1 ø20 1 ø12 ø12 ø12 0.5 0.5 10 20 30 31 50 100 101 200 300 10 20 30 31 Stroke (mm) 100 101 200 300 Stroke (mm) MGPL32 to 63 MGPL32 to 63 50 50 Load weight m (kg) Load weight m (kg) 50 ø63 ø50, 63 ø50 ø50, 63 10 ø40 ø40 ø40 ø63 ø50 ø50, 63 10 ø50, 63 ø40 ø40 ø40 ø32 ø32 ø32 ø32 5 ø32 ø32 5 10 20 30 40 50 51 100 101 200 300 10 20 30 40 50 51 Stroke (mm) 100 101 200 300 200 300 Stroke (mm) MGPL80, 100 MGPL80, 100 50 50 ø100 ø100 ø100 ø80 ø80 ø80 ø100 Load weight m (kg) Load weight m (kg) ø100 ø80 10 ø80 ø100 10 5 ø80 5 10 20 29 30 49 50 Stroke (mm) 3.22-14 100 200 300 10 20 29 30 49 50 Stroke (mm) 100 Compact Guide Cylinder Series MGP Operating Range when Used as Stopper m MGPM12 to 25 (Slide bearing) υ ø25 m ∗ When selecting a model with a longer l dimension, be sure to choose a bore size which is sufficiently large. Caution CL 100 Weight of transfered object: m (kg) υ l: Approx. 50mm l: Approx. 50mm Bore Sizes ø12 to 25/MGPM12 to 25 (Slide bearing) Handling precautions 50 40 MLG ø20 30 CNA ø16 20 CNG ø12 MNB 10 CNS 5 4 CLS 3 CB 2 Note 1) When using as a stopper, select a model with a stroke of 30mm or less. Note 2) Model MGPL (ball bushing) cannot be used as a stopper. 1 CV/MVG 5 10 20 30 40 50 Transfer speed: υ (m/min) CXW CXS Bore Sizes ø32 to 100/MGPM32 to 100 (Slide bearing) CXT MX υ m ∗ When selecting a model with a longer l dimension, be sure to choose a bore size which is sufficiently large. Caution MXU 2000 MXH ø100 1000 Weight of transfered object: m (kg) υ m l: Approx. 50mm l: Approx. 50mm MGPM32 to 100 (Slide bearing) ø80 MXS ø63 500 400 MXQ ø50 MXF 300 ø40 200 MXW ø32 MXP 100 MG Handling precautions Note 1) When using as a stopper, select a model with a stroke of 50mm or less. 50 40 Note 2) Model MGPL (ball bushing) cannot be used as a stopper. 30 MGP 5 10 20 30 40 50 Transfer speed: υ (m/min) MGQ MGG MGC MGF MGZ CY MY 3.22-15 Series MGP 1. Water Resistant 3. Clean Room Series Ideal for use in a machine tool envrionment exposed to coolants. Also applicable for use in an environment with water splashing such as food processing and car wash equipment, etc. Applicable in a clean room environment. Ideal for use in conveyor lines for semi-conductor (LSI), liquid crystal (LCD), food processing, pharmaceutical, and electronic parts, etc. Specifications Specifications Applicable series Bearing type Bore size (mm) MGPM Slide bearing 20, 25, 32, 40, 50, 63, 80, 100 Rubber cushion Without cushion MGPMR MGPMV Cushion Applicable series Bearing type Bore size (mm) Stroke (mm) MGPL Ball bushing 20 25 32 20 to 200 12 16 10 to 100 40 50 25 to 200 63 ∗ Specifications other than above are identical to the standard basic type. ∗ Specifications other than above are identical to the standard basic type. How to Order MGPM Bore size How to Order R 12 Y7BAL Stroke MGPL Bore size Stroke Water resistant 2 color indication solid state switch Water resistant cylinder R V Clean room specification NBR (nitrile rubber) seal FKM (fluoro rubber) seal 12 13 ∗ Stainless steel parts are available as special order products. Relief port type Vacuum port type Dimensions Dimensions M5 x 0.8 Relief port (Vacuum port) FB B + Stroke 5 10 A + Stroke FB (mm) Bore size (mm) 20 25 32 40 50 63 80 100 A B 50mm stroke or less 51mm stroke or more 66 66 97.5 67.5 67.5 99 109 71.5 114 109 78 114 117.5 83 129 117.5 88 129 121 102.5 148 141 120 166 B + Stroke A + Stroke FB 19 20 22 22 23 23 24 29 (mm) Bore size (mm) 12 16 20 25 ∗ Other dimensions are identical to the standard type. A 30mm stroke Over 30mm Over 100mm stroke or less to 100mm stroke B FB 68 78 93 98.5 55 59 66 66.5 18 18 19 19 56 62 76 82.5 — — 117 117.5 2. Copper-free Series (mm) (applicable to CRT manufacturing process) To prevent the influence of copper ions or halogen ions during CRT manufacturing processes, copper and fluorine materials are not used as component parts. Specifications Applicable series Bearing type MGPM Slide bearing MGPL Ball bushing 12, 16, 20, 25, 32 40, 50, 63, 80, 100 Bore size (mm) ∗ Specifications and dimensions other than above are identical to the standard basic type. How to Order 20 MGP M Bore size Stroke Bearing type M L Slide bearing Ball bushing Copper-free specification 3.22-16 Bore size (mm) 32 40 50 63 A 50mm stroke Over 50mm Over 100mm stroke to 100mm stroke or less 93 93 104 104 110 110 125 125 ∗ Other dimensions are identical to the standard type. 130 130 145 145 B FB 71.5 78 83 88 22 22 23 23 Series Compact Guide Cylinder MGP Auto Switches/Proper Mounting Position for Stroke End Detection Auto switch For D-P5DW (∗ Cannot be mounted on bore sizes ø32 or less.) ø40 to ø63 CL A 16.5 16.5 MLG CNA B CNG MNB Hs Hs CNS For 25mm stroke ∗ For bore sizes ø40 through 63 with two switches, one switch is mounted on each side. ø80, ø100 Bore size (mm) 12 16 20 25 32 A 1.5 4.5 4 4.5 5.5 B 3 4 8 8 7 Bore size (mm) 40 50 63 80 100 A 9.5 7.5 10 13 17.5 (mm) B 9.5 11.5 14 18.5 23.5 Note 1) Minimum mountable strokes for auto switch are 10mm or more for two switches, and 5mm or more for one switch. CB CV/MVG CXW Note 2) Type D-P5DW can be mounted only on bore sizes ø40 through ø100. Bore size (mm) 40 50 63 80 100 Hs 44.5 50 57 60.7 70.8 (mm) Ht — — — 84.4 96.1 ∗ Minimum mountable strokes for auto switch are 10mm or more for two switches, and 5mm or more for one switch. Hs Auto Switch Mounting CXT MX MXU MXH MXQ Caution Caution Auto switch mounting tool Auto switch mounting tool • When tightening the auto switch mounting screw (included with auto switch), use a watchmakers screw driver with a handle about 5 to 6mm in diameter. • When tightening hexagon socket head cap screws of the auto switch, use hexagon wrench key 2 or 2.5 with the appropriate screws. Tightening torque Tightening torque • Tighten with a torque of 0.05 to 0.1N⋅ m. As a rule, it should be turned about 90° past the point at which tightening can be felt. • Tighten M2.5 screws with a torque of about 0.3 to 0.5N⋅ m, and M3 screws with a torque of about 0.5 to 0.7 N⋅ m. Switch mounting screw (M2.5 x 4 l ) CXS MXS For D-P5DW Watchmakers screw driver CLS Ht Proper mounting position (mm) MXF MXW MXP MG Hexagon wrench key 2 Hexagon socket head cap screw (M2.5 x 8 l ) MGP (included with auto switch) MGQ Auto switch MGG MGC MGF MGZ Hexagon wrench key 2.5 Auto switch Hexagon socket head cap screw (M3 x 16 l ) CY MY 3.22-17 Series MGP Construction Series MGPM Series MGPL MGPM12 to 25 MGPL12 to 25 ø12, ø16 50mm stroke or less ø12, ø16 over 30mm stroke ø12, ø16 over 50mm stroke ø20, ø25 over 30mm to 100mm stroke 50mm stroke or less 30mm stroke or less ø20, ø25 over 50mm stroke ø20, ø25 over 100mm stroke MGPM32 to 100 MGPL32 to 100 ø32 to ø63 over 50mm to100mm stroke ø80, ø100 over 50mm stroke to 200mm stroke Over 50mm stroke 50mm stroke or less ø32 to ø63 over 100mm stroke ø80, ø100 over 200mm stroke 50mm stroke or less ø50 or larger Parts list No. Parts list 1 2 Description Body Piston Material Aluminum alloy Aluminum alloy Stainless steel Carbon steel Aluminum bearing alloy Aluminum alloy casting Lead bronze casting 3 Piston rod 4 Collar 5 Bushing 6 Head cover Aluminum alloy 7 Guide rod 8 Plate 9 Plate mounting bolt 10 Snap ring 11 Snap ring Carbon steel Carbon steel Carbon steel Carbon tool steel Carbon tool steel Note Hard anodized Chromated ø12 to ø25 ø32 to ø100 Hard chrome plated ø12 to ø40 Clear anodized Coated ø50 to ø100 ø50 to ø100 ø12 to ø63 Clear chromated ø80 to ø100 Coated Hard chrome plated Nickel plated Nickel plated Phosphate coated Phosphate coated Order No. MGP12-PS MGP16-PS MGP20-PS MGP25-PS MGP32-PS Contents Kits include items 21, 22, 23, and 24 from the table above. ∗ Seal kits are sets consisting of items 21 through 24 above, and can be ordered using the order number for each bore size. 3.22-18 Material Note Urethane Urethane Synthetic rubber Brass Nickel plated Plug (M-5P) ø12, ø16 Carbon steel Hexagon socket head taper plug ø20 to ø100 Nickel plated Lead bronze casting Slide bearing Felt Felt Resin Holder Ball bushing Aluminum alloy Spacer NBR Piston seal NBR Rod seal NBR Gasket A NBR Gasket B Description 12 Bumper A 13 Bumper B 14 Magnet 15 16 17 18 19 20 21∗ 22∗ 23∗ 24∗ Replacement parts: Seal kits Replacement parts: Seal kits Bore size (mm) 12 16 20 25 32 No. Bore size (mm) 40 50 63 80 100 Order no. MGP40-PS MGP50-PS MGP63-PS MGP80-PS MGP100-PS Contents Kits include items 21, 22, 23, and 24 from the table above. MGP Series Compact Guide Cylinder ø12 to ø25/MGPM, MGPL 4-YY depth YL øXAH7 depth 6 a c XB X CL MLG X ±0.02 øXA H7 b T-slot dimensions d CNA e (mm) øXA H7 3 Bore size (mm) 12 16 20 25 6 Section XX detail Section XX WB Z e d 2 2.5 2.8 3 c 3.7 3.7 4.5 4.5 b 7.4 7.4 8.4 8.4 a 4.4 4.4 5.4 5.4 6.2 6.7 7.8 8.2 CNG MNB CNS CLS WA Section XX Z HA: T-slot for hexagon bolt WA 4-NN through Section XX 4-øOA through CV/MVG 4-øOB depth of counter bore OL CXW X ±0.02 R T MX PW X øDA CXT MXU øDB H VA VB X ±0.02 CXS U L CB Bottom view 4-MM depth ML MXH øXAH7 depth 6 øXAH7 depth 6 2-P (Plug) GA PB J G FA FB Q GB S C + Stroke B + Stroke A + Stroke E 12 16 20 25 Standard stroke (mm) B 10, 20, 30, 40, 50, 75, 100 42 125, 150, 175, 200, 250 46 20, 30, 40, 50, 75, 100 53 125, 150, 175, 200 53.5 250, 300, 350, 400 C DA FA FB 29 6 33 8 37 10 37.5 12 Bore size (mm) Q R S T U VA VB 12 16 20 25 14 16 18 26 48 54 70 78 22 25 30 38 56 62 81 91 41 46 54 64 50 56 72 82 37 38 44 50 8 8 10 10 5 5 6 6 G GA GB H HA J K L MM ML NN OA OB OL P PA PB PW 26 30 36 42 11 11 10.5 11.5 58 64 83 93 M4 M4 M5 M5 13 15 18 21 13 15 18 21 18 22 24 30 M4 M5 M5 M6 10 12 13 15 M4 M5 M5 M6 4.3 4.3 5.6 5.6 M5 M5 1/8 1/8 13 8 15 10 12.5 10.5 12.5 13.5 Over 30st to 100st 20 24 24 24 40 44 44 44 A Over 50st to 100st 60.5 64.5 Over 100st 85 95 DB 8 10 110 110 120 120 A Over 50st to 200st 84.5 85 Over 200st 122 122 DB 12 16 200 200 200 200 (mm) E — — 300 300 30st Over 100st Over 200st Over 300st 30st or less Over to 200st to 300st to 100st X 60 60 77 77 23 24 28 34 15 17 29 29 25 27 39 39 105 105 117 117 — — 167 167 4.5 4.5 5.5 5.5 XA XB 3 3 3 4 A 50st or less Over 100st 0 0 18.5 18.5 43 49 (mm) MGPL (ball bushing)/Dimensions A, DB, E E 50st or less 0 0 Over 50st to 200st 31.5 31.5 Over 200st 69 68.5 YL Z M5 M5 M6 M6 10 10 12 12 5 5 17 17 3.5 3.5 3.5 4.5 Bore size (mm) 30st or less 20 63 25 69.5 Over 100st 85 95 55 65 DB (mm) 30st or less Over 30st to 100st Over 100st 1 3 13 19 43 49 6 8 A Over 30st to 100st Over 100st to 200st Over 200st 80 85.5 104 104.5 122 122 DB 10 13 E 10 16 27 32 Over 100st to 200st 51 51 MXW MXP MG MGP MGQ MGG MGF (mm) 30st 30st or less Over to 100st MXF MGC E Over 50st to 100st Over 30st to 100st 18 19 25 28.5 YY MGPL (ball bushing)/Dimensions A, DB, E Bore size (mm) 30st or less 12 43 16 49 MGPM (slide bearing)/Dimensions A, DB, E Bore size (mm) 50st or less 20 53 25 53.5 8 8 9.5 9.5 WB Over 100st Over 200st Over 300st to 200st to 300st MGPM (slide bearing)/Dimensions A, DB, E Bore size (mm) 50st or less 12 42 16 46 7.5 8 8.5 9 WA 30st or less MXQ Refer to "Manufacture of Intermediate Strokes" on page 3.22-6 for intermediate strokes other than the standard strokes. (mm) MGPM, MGPL Common dimensions Bore size (mm) MXS 2-P PA + Stroke K MGZ Over 200st CY 69 68.5 MY 3.22-19 MGP Series ø32 to ø63/MGPM, MGPL 4-YY depth YL øXAH7 depth XL X ±0.02 X øXAH7 a b T-slot dimensions c d XB e (mm) Bore size (mm) 32 40 50 63 XC XL Section XX detail Section XX WB Z Section XX 4-MM depth ML R T Section XX PW X øDA U 4-NN through 4-øOA through 4-øOB depth of counter bore OL WA øDB H e 9.5 11 13.5 18.5 Bottom view HA: T-slot for hexagon bolt VA d 3.5 4 4.5 7 c 5.5 5.5 7.5 10 WA Z VB X ±0.02 L b 10.5 10.5 13.5 17.8 X ±0.02 øXAH7 a 6.5 6.5 8.5 11 2-P (Plug) GC øXAH7 depth XL PB J K øXAH7 depth XL 2-P GB GA Q PA + Stroke G FA FB S C + Stroke B + Stroke A + Stroke E Refer to "Manufacture of Intermediate Strokes" on page 3.22-6 for intermediate strokes other than the standard strokes. MGPM, MGPL Common dimensions Bore size (mm) 32 40 50 63 Standard stroke (mm) B 59.5 25, 50, 75, 100, 66 125, 150, 175, 200 250, 300, 350, 400 72 77 C 37.5 44 44 49 (mm) DA FA FB G GA GB GC 12 12 16 16 48 54 64 78 12.5 9 14 10 14 11 16.5 13.5 16 16 20 20 10 10 12 12 12.5 14 12 16.5 H HA J K L MM ML NN OA OB OL P PA PB PW Q 112 120 148 162 M6 M6 M8 M10 24 27 32 39 24 27 32 39 34 40 46 58 M8 M8 M10 M10 20 20 22 22 M8 M8 M10 M10 6.6 6.6 8.6 8.6 1/8 1/8 1/4 1/4 7 13 9 14 WA Bore size (mm) R S T 32 40 50 63 96 104 130 130 44 44 60 70 110 118 146 158 U VA VB 25st or less 78 98 63 86 106 72 110 130 92 124 142 110 24 24 24 28 Over 25st to 100st Over 100st to 200st 48 48 48 52 124 124 124 128 MGPM (slide bearing)/Dimensions A, DB, E Bore size (mm) 50st or less 32 97 40 97 50 106.5 63 106.5 3.22-20 A Over 50st to 200st 102 102 118 118 Over 200st 140 140 161 161 DB 20 20 25 25 WB Over 200st Over 300st to 300st 200 200 200 200 (mm) E 50st or less 37.5 31 34.5 29.5 Over 50st to 200st 42.5 36 46 41 Over 200st 80.5 74 89 84 300 300 300 300 25st Over 100st Over 200st Over 300st 25st or less Over to 100st to 300st to 200st 33 34 36 38 45 46 48 50 83 84 86 88 121 122 124 124 171 172 174 174 X 11 7.5 11 7.5 14 9 14 9 XA XB XC XL 42 50 66 80 4 4 5 5 4.5 4.5 6 6 3 3 4 4 6 6 8 8 15 18 21.5 28 A Over 50st to 100st 98 98 114 114 Over 100st to 200st Over 200st 118 118 134 134 140 140 161 161 DB 16 16 20 20 30 30 40 50 YY YL Z M8 M8 M10 M10 16 16 20 20 MGPL (ball bushing)/Dimensions A, DB, E Bore size (mm) 50st or less 32 81 40 81 50 93 63 93 34 38 47 55 21 22 24 24 (mm) E 50st or less Over 50st to 100st 21.5 15 21 16 38.5 32 42 37 Over 100st to 200st 58.5 52 62 57 Over 200st 80.5 74 89 84 Series Compact Guide Cylinder MGP ø80, ø100/MGPM, MGPL 4-YY depth YL ø6H7 depth 10 T-slot dimensions MLG X X ±0.02 a b CL CNA ø6H7 c d CNG 7 e MNB ø6H7 5 (mm) 10 Bore size (mm) Section XX detail 80 100 Section XX WB Z b 20.3 23.3 a 13.3 15.3 WA c 12 13.5 e d 8 10 22.5 30 CNS CLS CB Section XX 4-MM depth ML Bottom view HA: T-slot for hexagon bolt CV/MVG L Z 4-NN through 4-øOA through WA CXW 4-øOB depth of counter bore 8 Section XX CXS X ±0.02 R T U MX MXU PW X øDA H VA VB X ±0.02 CXT MXH øDB MXS ø6H7 depth 10 PB 2-Rc 3/8 (Plug) MXQ ø6H7 depth 10 2- 3/8 GB GA 10 JA J JB GC K FA FB MXF Q PA + Stroke S C + Stroke G MXW E B + Stroke A + Stroke Refer to "Manufacture of Intermediate Strokes" on page 3.2-6 for intermediate strokes other than the standard strokes. MGPM, MGPL Common dimensions Bore size (mm) Standard stroke (mm) 80 100 25, 50, 75, 100, 125, 150, 175, 200 250, 300, 350, 400 Bore size (mm) 80 100 C U 22 25 A Over 50st to 200st 142 162 Over 200st 193 203 30 36 R MGP MM ML NN OA OB PA PB PW Q M12 M14 25 31 M12 M14 10.6 17.5 14.5 25.5 74 52 174 12.5 20 17.5 32.5 89 64 210 GA GB GC H HA J WA 52 72 JA JB K WB Over 25st Over 100st Over 200st to 100st to 200st to 300st Over 300st DB MG L G 128 148 200 220 MGPM (slide bearing)/Dimensions A, DB, E Bore size (mm) 50st or less 80 115 100 137 (mm) 18 91.5 19 15.5 14.5 202 M12 45.5 38 7.5 46 54 25 111.5 23 19 18 240 M14 55.5 45 10.5 56 62 DA FA FB VA VB 25st or less 75 198 156 180 140 28 90 236 188 210 166 48 S T B 96.5 56.5 25 116 66 30 (mm) 50st or less 18.5 21 45.5 46 Over 200st 96.5 87 YY YL Z 100 124 M12 M14 24 28 28 11 25st Over 100st Over 200st 25st or less Over to 100st to 200st to 300st Over 300st 300 320 E Over 50st to 200st X 42 35 54 47 92 85 128 121 178 171 A Over 25st to 50st 130 147 Over 50st to 200st Over 200st 160 180 193 203 DB 25 30 MGQ MGG MGC MGPL (ball bushing)/Dimensions A, DB, E Bore size (mm) 25st or less 80 109.5 100 121 MXP (mm) E 25st or less Over 25st to 50st 13 5 33.5 31 Over 50st to 200st 63.5 64 Over 200st 96.5 87 MGF MGZ CY MY 3.22-21 Compact Guide Cylinder: With Air Cushion Series MGP ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 How to Order Compact Guide Cylinder 50 A MGP M 32 Z73 Number of auto switches Compact guide cylinder Bearing type Slide bearing Ball bushing M L 2 pcs. 1 pc. Nil S Auto switch type Without auto switch (built-in magnet cylinder) Nil ∗ Refer to the table below for auto switch model numbers. Bore size 16 20 25 32 40 16mm 20mm 25mm 32mm 40mm 50 63 80 100 With air cushion 50mm 63mm 80mm 100mm Cylinder stroke (mm) Refer to the standard stroke table on page 3.22-23. Thread Port (ø20 to ø100) Rc(PT) TF G(PF) Applicable auto switches Load voltage Type Reed switch Special function Electrical Indicator entry light Wiring (output) DC 3 wire — 2 wire 24V 5V — — Z76   — IC circuit 12V 100V — Z73    — 5V 12V 100V or less IC circuit — Grommet 3 wire (NPN) 5V 12V 3 wire (PNP) — 2 wire Diagnostic indication (2 colour indicator) Grommet Yes 3 wire (NPN) 3 wire (PNP) 12V 24V 5V 12V — Z80   — Y69A Y59A    Y7PV Y7P    Y69B Y59B    Y7NWV Y7NW    Y7PWV Y7PW    Y7BWV Y7BW    — Y7BA —   —   — Water resistant (2 colour indicator) Magnetic field resistant (2 colour indicator) Note 1) Lead wire symbols 2 wire Note 3) — 0.5m ...... Nil (Example) Y69B 3m ......... L Y69BL 5m ......... Z Y69BZ Note 2) Solid state auto switches marked with a "" are produced upon receipt of order. Note 3) Type D-P5DW cannot be mounted on bore sizes of ø32 or less. — P5DW Relay, PLC IC circuit — IC circuit 12V 3.22-22 — Yes No Solid state switch AC Lead wire length (m) Note 1) Auto switch model Electrical entry direction Applicable load 0.5 3 5 (Nil) (L) (Z) Perpendicular In-line — Relay, PLC Compact Guide Cylinder With Air Cushion Series MGP Specifications Double acting Action Fluid Proof pressure Maximum operating pressure Air 1.5MPa 1.0MPa 0.15MPa ø16 Minimum operating pressure Piston speed CL ø20 to ø100 0.12MPa ø16 to ø63 –10 to 60° C (with no freezing) 50 to 500mm/s ø80, ø100 50 to 400mm/s Ambient and fluid temperature Cushion MLG CNA Air cushion at both ends (without bumper) Lubrication Non-lube Stroke length tolerance +1.5 0 mm CNG Standard Strokes MNB Bore size (mm) 16 20 to 63 80, 100 CNS Standard stroke (mm) 25, 50, 75, 100 CLS 25, 50, 75, 100, 125, 150, 175, 200 50, 75, 100, 125, 150, 175, 200 CB Manufacture of Intermediate Strokes CV/MVG Modification method Strokes provided in 1mm increments by changing the collar on a standard stroke cylinder. CXW Part number Indicate -XC19 at the end of the standard part number. ø16 26 to 99 CXS Applicable stroke (mm) Example ø20 to ø63 26 to 199 CXT ø80, ø100 51 to 199 Part no.: MGPM20–35A–XC19 A collar 15mm in width is installed in a MGPM20–50A. C dimension is 112mm. MX Note 1) Intermediate strokes (in 1mm increments) with a special body are available by special order. Auto switch mounting bracket part no. for D-P5DW Bore size (mm) Mounting bracket part no. MXH Theoretical Output OUT (N) Notes Switch mounting bracket Hexagon socket head cap screw 40, 50, 63, (M2.5 x 8 l ) 2 pcs. BMG1-040 80, 100 Hexagon socket head cap screw (M3 x 16 l ) 2 pcs. Spring washer (nominal size 3) MXU MXS IN (N) (N) Rod Bore size size Operating Piston area (mm) (mm) direction (mm²) 0.2 16 20 25 32 40 50 63 80 100 8 10 12 16 16 20 20 25 30 MXQ Operating pressure (MPa) 0.3 OUT 201 40 60 0.4 80 0.5 0.6 0.8 0.9 1.0 101 121 0.7 141 161 181 201 IN 151 30 45 60 76 91 106 121 136 151 OUT 314 63 94 126 157 188 220 251 283 314 IN 236 47 71 94 118 142 165 189 212 236 OUT 491 98 147 196 246 295 344 393 442 491 IN 378 76 113 151 189 227 265 302 340 378 OUT 804 161 241 322 402 482 563 643 724 804 482 543 603 IN 603 121 181 241 302 362 422 OUT 1257 251 377 503 629 754 880 1006 1131 1257 634 IN 1056 211 317 422 528 OUT 1963 393 589 785 982 1178 1374 1570 1767 1963 660 825 739 845 950 1056 IN 1649 330 495 990 1154 1319 1484 1649 OUT 3117 623 935 1247 1559 1870 2182 2494 2805 3117 561 IN 2803 OUT 5027 841 1121 1402 1682 1962 2242 2523 2803 1005 1508 2011 2514 3016 3519 4022 4524 5027 IN 4536 907 1361 1814 2268 2722 3175 3629 4082 4536 OUT 7854 1571 2356 3142 3927 4712 5498 6283 7069 7854 IN 7147 1429 2144 2859 3574 4288 5003 5718 6432 7147 Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm²) MXF MXW MXP MG MGP MGQ MGG MGC MGF MGZ CY MY 3.22-23 Series MGP Weights Ball bushing: MGPL16 to 100 Slide bearing: MGPM16 to 100 (kg) (kg) Bore size (mm) Model 16 Standard stroke (mm) Bore size (mm) Standard stroke (mm) Model 25 50 75 100 125 150 175 200 25 50 75 100 125 150 175 200 MGPM16 0.51 0.69 0.78 0.91 — — — — 16 MGPL16 0.56 0.66 0.78 0.89 — — — — 20 MGPM20 0.89 1.14 1.34 1.54 1.74 1.94 2.13 2.33 20 MGPL20 0.97 1.12 1.30 1.50 1.68 1.85 2.03 2.20 25 MGPM25 1.23 1.60 1.87 2.14 2.41 2.68 2.95 3.23 25 MGPL25 1.34 1.54 1.78 2.05 2.28 2.51 2.74 2.97 32 MGPM32 1.98 2.51 2.77 3.15 3.53 3.91 4.29 4.68 32 MGPL32 1.81 2.34 2.57 2.94 3.26 3.58 3.89 4.21 40 MGPM40 2.34 2.91 3.21 3.64 4.06 4.49 4.92 5.34 40 MGPL40 2.15 2.73 3.01 3.42 3.78 4.14 4.50 4.86 50 MGPM50 3.92 4.75 5.29 5.93 6.57 7.21 7.85 8.49 50 MGPL50 3.65 4.47 4.95 5.71 6.14 6.69 7.24 7.79 63 MGPM63 4.94 5.89 6.54 7.29 8.05 8.81 9.56 10.32 63 MGPL63 4.66 5.60 6.20 7.07 7.61 8.28 8.95 9.61 80 MGPM80 — 8.98 8.88 100 MGPM100 — 14.2 9.64 10.6 15.1 16.5 11.5 12.5 13.4 14.3 80 MGPL80 — 17.8 19.1 20.5 21.8 100 MGPL100 — 13.7 Allowable Rotational Torque of Plate (Air Cushion) 9.63 10.5 14.9 16.0 11.3 12.1 12.9 13.7 17.2 18.4 19.6 20.8 Non-rotating Accuracy of Plate Torque: T (N⋅ m) +θ –θ T (N⋅ m) Bore size (mm) 16 20 25 32 40 50 63 80 100 3.22-24 Stroke (mm) For non-rotating accuracy θ without load, use a value no more than the values in the table as a guide. Non-rotating accuracy θ Bearing type 25 50 75 100 125 150 175 200 Bore size (mm) MGPM 0.53 0.84 0.69 0.58 — — — — 16 ±0.08° ± 0.10° MGPL 1.27 0.86 0.65 0.52 — — — — 20 MGPM 0.99 2.23 1.88 1.63 1.44 1.28 1.16 1.06 25 ±0.07° ± 0.09° MGPL 2.66 1.94 1.52 1.57 1.34 1.17 1.03 0.93 32 MGPM 1.64 3.51 2.96 2.57 2.26 2.02 1.83 1.67 40 ±0.06° ± 0.08° MGPL 4.08 3.02 2.38 2.41 2.05 1.78 1.58 1.41 50 MGPM 6.35 6.64 5.69 4.97 4.42 3.98 3.61 3.31 63 ±0.05° ± 0.06° MGPL 5.95 5.89 5.11 6.99 6.34 5.79 5.33 4.93 80 MGPM 7.00 7.32 6.27 5.48 4.87 4.38 3.98 3.65 100 ±0.04° ± 0.05° 7.70 6.98 6.38 5.87 5.43 9.50 8.60 7.86 7.24 9.80 9.10 MGPL MGPM MGPL 6.55 13.0 9.17 6.49 5.62 13.8 12.0 10.6 11.2 9.8 12.8 11.6 10.7 MGPM 14.7 15.6 13.5 11.9 10.7 MGPL 10.2 12.5 11.0 14.3 13.0 11.9 11.0 10.2 MGPM — 26.0 22.9 20.5 18.6 17.0 15.6 14.5 MGPL — 25.2 22.7 20.6 18.9 17.3 16.0 14.8 MGPM — 41.9 37.5 33.8 30.9 28.4 26.2 24.4 MGPL — 41.7 37.9 34.6 31.8 29.3 27.2 25.3 9.69 8.86 8.16 MGPM MGPL Series MGP (With Air Cushion) Model Selection Selecting Conditions Vertical Horizontal l CL l m MLG Mounting orientation CNA m CNG MNB CNS Maximum speed (mm/s) Graph (Slide bearing type) Graph (Ball bushing type) 200 400 200 400 1, 2 3, 4 15 , 16 17 , 18 5 to 9 10 to 14 19 , 20 21 , 22 CLS CB CV/MVG Selection Example 1 (Vertical Mounting) Selection Example 2 (Horizontal Mounting) Selecting conditions Mounting: Vertical Bearing type: Ball bushing Stroke: 75mm Maximum speed: 200mm/s Load weight: 7kg Eccentric distance:70mm Find the point of intersection for the load weight of 7kg and the eccentric distance of 70mm on graph 5 , based on vertical mounting, ball bushing, 75mm stroke, and the speed of 200mm/s. → MGPL25-75A is selected. Selecting conditions Mounting: Horizontal Bearing type: Slide bearing Distance between plate and load center of gravity: 40mm Maximum speed: 300mm/s Load weight: 8kg Stroke: 100mm Find the point of intersection for the load weight of 8kg and stroke of 100mm on graph 17 , based on horizontal mounting, slide bearing, the distance of 40mm between the plate and load center of gravity, and the speed of 300mm/s. → MGPM32-100A is selected. 5 75mm stroke or less V = 200mm/s CXW 17 l = 50mm V = 400mm/s 20 50 CXS CXT MX MXU MXH ø100 MXS ø80 ø50, 63 MXQ ø50, 63 ø40 MXF ø40 ø25 10 ø32 10 ø32 MXW 5 Load weight m (kg) Load weight m kg) ø25 ø20 ø16 MXP 5 ø25 ø20 ø20 ø16 MG MGP ø16 MGQ 1 MGG MGC MGF 1 0.1 10 50 100 Eccentric distance l (mm) 200 10 20 25 26 50 100 200 MGZ CY Stroke (mm) MY 3.22-25 Series MGP Vertical Mounting Operating pressure: 0.4MPa Operating pressure: 0.5MPa or more Slide Bearing MGPM16 to 100 1 25mm stroke V = 200mm/s 2 Over 25mm stroke V = 200mm/s 300 200 300 ø100 200 ø80 ø80 100 100 ø63 ø63 50 50 ø50 Load weight m (kg) Load weight m (kg) ø50 ø40 ø40 ø32 10 ø100 ø25 ø20 5 ø32 10 ø25 ø20 5 ø16 ø16 1 1 0.5 0.5 10 50 100 200 10 50 Eccentric distance l (mm) 200 Eccentric distance l (mm) 3 25mm stroke V = 400mm/s 4 Over 25mm stroke V = 400mm/s 300 300 ø100 200 ø100 200 ø80 ø80 100 100 ø63 50 ø63 50 ø50 ø50 ø40 Load weight m (kg) Load weight m (kg) 100 ø32 10 ø25 ø40 ø32 10 ø25 5 5 ø20 ø20 ø16 ø16 1 1 0.5 0.5 10 50 100 Eccentric distance l (mm) 3.22-26 200 10 50 100 Eccentric distance l (mm) 200 Compact Guide Cylinder With Air Cushion Vertical Mounting Series MGP Operating pressure: 0.4MPa Operating pressure: 0.5MPa or more Ball Bushing MGPL16 to 25 5 75mm stroke or less V = 200mm/s 6 Over 75mm stroke V = 200mm/s 20 10 ø25 5 ø20 ø25 10 Load weight m (kg) Load weight m (kg) 20 ø16 CL MLG ø20 5 CNA ø16 CNG MNB 1 CNS 1 10 50 100 200 10 50 Eccentric distance l (mm) 100 200 CB MGPL32 to 63 7 25mm stroke V = 200mm/s CV/MVG 8 Over 25mm stroke V = 200mm/s 100 100 CXS 50 ø50 CXT Load weight m (kg) ø50 Load weight m (kg) CXW ø63 ø63 50 CLS Eccentric distance l (mm) ø40 ø32 ø40 MX ø32 MXU 10 5 5 MXH 10 MXS 10 50 100 200 10 50 100 200 Eccentric distance l (mm) Eccentric distance l (mm) MXQ MXF MGPL80, 100 MXW 9 V = 200mm/s MXP Load weight m (kg) 200 ø100 MG ø80 MGP 100 MGQ 50 MGG MGC MGF MGZ 10 10 50 100 200 CY Eccentric distance l (mm) MY 3.22-27 Series MGP Vertical Mounting Ball Bushing Operating pressure: 0.4MPa MGPL16 to 25 10 75mm stroke or less V = 400mm/s 11 Over 75mm stroke V = 400mm/s Load weight m (kg) 5 Load weight m (kg) 5 ø25 ø25 ø20 ø20 ø16 ø16 1 1 10 50 100 200 10 50 100 200 Eccentric distance l (mm) Eccentric distance l (mm) MGPL32 to 63 12 25mm stroke V = 400mm/s 13 Over 25mm stroke V = 400mm/s 50 10 ø63 ø63 ø50 ø50 Load weight m (kg) Load weight m (kg) 50 ø40 5 ø32 ø40 5 ø32 1 1 10 50 100 200 MGPL80, 100 14 V = 400mm/s 200 ø100 100 ø80 50 10 10 50 100 Eccentric distance l (mm) 3.22-28 10 50 100 Eccentric distance l (mm) Eccentric distance l (mm) Load weight m (kg) 10 200 200 Compact Guide Cylinder With Air Cushion Series MGP Slide Bearing Horizontal Mounting MGPM16 to 100 15 l = 50mm V = 200mm/s 16 l =100mm V = 200mm/s ø100 50 50 ø80 ø100 ø50, 63 ø50, 63 ø80 CL ø50, 63 ø32, 40 ø50, 63 ø32, 40 ø32, 40 ø25 10 MLG ø32, 40 10 ø25 ø20 CNA ø20 CNG 5 Load weight m (kg) Load weight m (kg) 5 ø25 ø16 ø20 ø16 ø25 1 1 MNB ø16 ø20 CNS ø16 CLS CB CV/MVG CXW CXS 0.1 0.1 10 20 25 26 50 100 10 200 20 Stroke (mm) ø40 ø32 50 100 200 MXU 50 ø80 ø100 ø50, 63 ø80 ø40 MXH ø50, 63 MXS ø40 MXQ ø50, 63 ø32 10 ø32, 40 10 ø32 MXF ø25 ø25 MXW ø20 ø20 ø16 Load weight m (kg) 5 Load weight m (kg) 5 ø25 CXT MX 18 l =100mm V = 400mm/s ø100 ø50, 63 26 Stroke (mm) 17 l = 50mm V = 400mm/s 50 25 ø16 1 ø20 MXP ø16 ø25 MG ø20 1 MGP ø16 MGQ MGG MGC MGF 0.1 0.1 10 20 25 26 Stroke (mm) 50 100 200 10 20 25 26 50 100 200 MGZ CY Stroke (mm) MY 3.22-29 MGP Series Ball Bushing Horizontal Mounting 19 l = 50mm V = 200m/s 20 l =100mm V = 200m/s MGPL16 to 25 MGPL16 to 25 10 10 ø25 ø25 ø20 ø25 ø20 ø25 5 ø20 Load weight m (kg) Load weight m (kg) 5 ø16 ø16 ø20 ø16 ø16 1 1 20 50 75 76 100 200 20 50 Stroke (mm) 75 76 100 200 Stroke (mm) MGPL32 to 63 MGPL32 to 63 30 30 ø50, 63 20 ø50, 63 Load weight m (kg) Load weight m (kg) 20 ø32, 40 ø50, 63 ø32, 40 ø32, 40 10 ø50, 63 ø50, 63 ø32, 40 10 ø50, 63 ø32, 40 ø32, 40 5 5 20 25 26 50 75 76 100 200 20 25 26 50 75 76 100 200 100 200 Stroke (mm) Stroke (mm) MGPL80, 100 MGPL80, 100 50 50 40 ø100 40 30 ø80 30 Load weight m (kg) Load weight m (kg) ø100 20 10 ø80 20 10 5 5 20 50 100 Stroke (mm) 3.22-30 200 20 50 Stroke (mm) Compact Guide Cylinder Series With Air Cushion MGP Ball Bushing Horizontal Mounting 21 l = 50mm V = 400m/s 22 l =100mm V = 400m/s MGPL16 to 25 MGPL16 to 25 10 10 ø25 ø25 CL ø25 5 ø25 ø20 Load weight m (kg) Load weight m (kg) 5 ø20 ø16 ø20 MLG CNA ø20 CNG ø16 MNB ø16 CNS ø16 1 CLS 1 20 50 75 76 100 200 20 50 Stroke (mm) 75 76 100 200 CB Stroke (mm) MGPL32 to 63 CV/MVG MGPL32 to 63 30 30 CXW CXS 20 ø50, 63 ø50, 63 Load weight m (kg) Load weight m (kg) 20 ø50, 63 ø32, 40 ø32, 40 ø32, 40 10 CXT ø50, 63 MX ø50, 63 ø32, 40 10 ø50, 63 MXU ø32, 40 MXH ø32, 40 MXS 5 MXQ 5 20 25 26 50 75 76 100 200 20 25 26 Stroke (mm) 75 76 100 200 MXF Stroke (mm) MGPL80, 100 MXW MGPL80, 100 50 50 40 ø100 40 30 ø80 30 Load weight m (kg) Load weight m (kg) 50 20 10 MXP MG ø100 MGP ø80 20 MGQ MGG MGC 10 MGF 5 MGZ 5 20 50 100 Stroke (mm) 200 20 50 100 200 CY Stroke (mm) MY 3.22-31 Series MGP Operating Range when Used as Stopper m MGPM16 to 25 (Slide bearing) 100 υ m ∗ When selecting a model with a longer l dimension, be sure to choose a bore size which is sufficiently large. ø25 Weight of transfered object: m (kg) υ l: Approx. 50mm l: Approx. 50mm Bore Sizes ø16 to 25/MGPM16 to 25 (Slide bearing) Caution 50 40 ø20 30 ø16 20 10 5 4 3 2 Handling precautions Note 1) When using as a stopper, select a model with a stroke of 25mm or less. 1 Note 2) Model MGPL (ball bushing) cannot be used as a stopper. 5 20 10 30 40 50 30 40 50 Transfer speed: υ (m/min) Bore Sizes ø32 to 100/MGPM32 to 100 (Slide bearing) υ m ∗ When selecting a model with a longer l dimension, be sure to choose a bore size which is sufficiently large. Caution 2000 ø100 1000 Weight of transfered object: m (kg) υ m l: Approx. 50mm l: Approx. 50mm MGPM32 to 100 (Slide bearing) ø80 ø63 500 400 ø50 300 ø40 200 ø32 100 Handling precautions Note 1) When using as a stopper, select a model with a stroke of 50mm or less. 50 40 Note 2) Model MGPL (ball bushing) cannot be used as a stopper. 30 3.22-32 5 10 20 Transfer speed: υ (m/min) Compact Guide Cylinder Series With Air Cushion MGP Copper-free Series (Applicable to CRT Manufacturing Process) To prevent the influence of copper ions or halogen ions during CRT manufacturing processes, copper and fluorine materials are not used as component parts. How to Order Specifications Applicable series Bearing type MGPM Slide bearing MGPL Ball bushing 20 MGP M Bore size Bearing type 16, 20, 25, 32, 40, 50, 63, 80, 100 Bore size (mm) Stroke M L ∗ Specifications and dimensions other than above are identical to the standard basic type. A With air cushion Slide bearing Ball bushing MLG Copper-free specification CNA Auto Switches/Proper Mounting Position for Stroke End Detection CNG For D-P5DW (∗ Cannot be mounted on bore sizes ø32 or less.) Auto switch CL MNB ø40 to ø63 CNS CLS A CV/MVG 16.5 16.5 CB B CXW CXS Hs Proper mounting position (mm) Bore size (mm) 16 20 25 32 A 17.5 26 23 16 B 15.5 11 14.5 21.5 Bore size (mm) 40 50 63 80 100 A 26 27.5 28 25 28.5 (mm) B 18 16.5 21 31.5 37.5 CXT Hs For 25mm stroke ø80, ø100 ∗ For bore sizes ø40 through 63 with two switches, one switch is mounted on each side. MXS Ht (mm) Bore size (mm) 40 50 63 80 100 Hs Hs 44.5 50 57 60.7 70.8 Ht — — — 84.4 96.1 ∗ Minimum mountable strokes for auto switch are 10mm or more for two switches, and 5mm or more for one switch. For D-P5DW Caution Auto switch mounting tool • When tightening the auto switch mounting screw (included with auto switch), use a watchmakers screw driver with a handle about 5 to 6mm in diameter. Tightening torque • Tighten with a torque of 0.05 to 0.1N⋅ m. As a rule, it should be turned about 90° past the point at which tightening can be felt. Flat head watchmakers screw driver Caution Switch mounting screw (M2.5 x 4 l ) Auto switch mounting tool (included with auto switch) • When tightening hexagon socket head cap screws of the auto switch, use hexagon wrench key 2 or 2.5 with the appropriate screws. Auto switch MXU MXH Note 1) Minimum mountable strokes for auto switch are 10mm or more for two switches, and 5mm or more for one switch. Auto Switch Mounting MX MXF MXW MXP MG MGP MGQ Hexagon wrench key 2 Hexagon socket head cap screw MGG (M2.5 x 8 l ) MGC Tightening torque • Tighten M2.5 screws with a torque of about 0.3 to 0.5N⋅ m, and M3 screws with a torque of about 0.5 to 0.7 N⋅ m. MXQ MGF Hexagon wrench key 2.5 Auto switch Hexagon socket head cap screw MGZ CY (M3 x 16 l ) MY 3.22-33 Series MGP Construction (With Air Cushion) Series MGPM Series MGPL MGPM16 to 25 MGPL16 to 25 ø16: 25mm stroke ø20, ø25: 75mm stroke or less ø16: 50mm stroke or larger 25mm stroke ø20, ø25: 100mm stroke or larger ø20, ø25: 50mm stroke or larger Cushion valve section MGPM32 to 100 MGPL32 to 100 ø32 to ø63: 50, 75mm stroke ø80, ø100: 50mm stroke or larger 50mm stroke or larger 25mm stroke 25mm stroke ø32 to ø63: 100mm stroke or larger Cushion valve section Parts list No. 1 2 Description Body Piston 3 Piston rod 4 Collar 5 Bushing 6 Head cover 7 8 9 10 11 12 13 14 15 16 17 Guide rod Plate Plate mounting bolt Snap ring Snap ring Magnet Plug (M-5P) Parts list Material Aluminum alloy Aluminum alloy Stainless steel Carbon steel Aluminum alloy Note Hard anodized Chromated ø16 to ø25 ø32 to ø100 Hard chrome plated ø16 to ø63 Clear anodized ø80, ø100 Coated Lead bronze casting Aluminum alloy Carbon steel Carbon steel Carbon steel Carbon tool steel Carbon tool steel Synthetic rubber Brass Hexagon socket head taper plug Carbon steel Slide bearing Lead bronze casting Felt Felt Holder Resin Ball bushing ø16 to ø25 Clear anodized ø32 to ø100 Coated Hard chrome plated Nickel plated Nickel plated Phosphate coated Phosphate coated ø16 ø20 to ø100 Nickel plated Nickel plated No. 18 19 20 21 22 23∗ 24∗ 25∗ 26∗ 27∗ 28∗ Description Spacer Wear ring Cushion valve Gasket Snap ring Piston seal Rod seal Cushion seal Gasket A Gasket B Gasket C Material Aluminum alloy Resin Steel NBR Carbon tool steel NBR NBR Urethane NBR NBR NBR Note Except ø16 Replacement parts: Seal kits Bore size (mm) 16 20 25 32 40 Kit no. Contents MGP16-A-PS Kits include items MGP20-A-PS 23, 24, 25 MGP25-A-PS 26, 27, 28 from the MGP32-A-PS table above. MGP40-A-PS Bore size (mm) 50 63 80 100 Kit no. Contents MGP50-A-PS Kits include items MGP63-A-PS 23, 24, 25 27, 28 MGP80-A-PS 26, from the MGP100-A-PS table above. ∗ Seal kits are sets consisting of items 23 through 28 above, and can be ordered using the kit number for each bore size. 3.22-34 Compact Guide Cylinder Series With Air Cushion MGP ø16 to ø25/MGPM, MGPL (With Air Cushion) T-slot dimensions 4-YY depth YL CL øXAH7 a b øXAH7 depth 6 MLG X X ±0.02 XB c d CNA e 3 (mm) Bore size (mm) 6 Section XX detail Section XX WB HA: T-slot for hexagon bolt Z Z c 3.7 4.5 4.5 d 2.5 2.8 3 e 6.7 7.8 8.2 2-cushion valve (width across flats CV) 4-øOA through 4-øOB depth of counter bore OL CB CV/MVG Section XX 4-NN through CXW R T PW X U øDA CXT MX øDB J 2-P GA PA + Stroke K FA FB øXAH7 depth 6 MXH Q GB C + Stroke B + Stroke A + Stroke G S MXS E MXQ Note 1) Refer to "Manufacture of Intermediate Strokes" on page 3.22-23 for intermediate strokes. Note 2) When adjusting the ø16 cushion valve, use a 3mm flat head watchmakers screw driver. 16 20 25 Bore size (mm) 16 20 25 Standard stroke (mm) B C Standard stroke (mm) R S 54 25, 50, 75, 100 70 25, 50, 75, 100, 125, 150, 175, 200 78 T 25 62 30 81 38 91 8 10 10 16 20 25 25st 71 78 78.5 A 50st 75st or more 89.5 71 86.5 84.5 87 85 DB 10 12 16 5 6 6 G GA GB H J K L MM ML 64 M4 15 30 11 8 36 10.5 8.5 83 M5 18 93 M5 21 42 11.5 9 15 18 21 22 24 30 M5 M5 M6 12 M5 x 0.8 4.3 8 4.5 13 M5 x 0.8 5.6 9.5 5.5 15 M6 x 1.0 5.6 9.5 5.5 46 56 54 72 64 82 HA WA 75st or less 100 to 175st 44 110 38 44 120 44 44 120 50 U VA VB MGPM (slide bearing)/Dimensions A, DB, E Bore size (mm) (mm) CV DA FA FB 25, 50, 75, 100 71 58 — 8 78 62 1.5 10 25, 50, 75, 100, 125, 150, 175, 200 78.5 62.5 1.5 12 MXF MXW MGPM, MGPL Common dimensions Bore size (mm) CNS MXU øXAH7 depth 6 PB 2-P (plug) MNB CLS WA WA CNG CXS VB X ±0.02 L H Section XX VA 4-MM depth ML b 7.4 8.4 8.4 a 4.4 5.4 5.4 16 20 25 X ±0.02 øXAH7 (mm) E 25st 50st 75st or more 0 18.5 0 0 8.5 6.5 0 8.5 6.5 WB 200st 75st or less 100 to 175st — 27 60 200 39 77 200 39 77 NN 200st — 117 117 MGPL (ball bushing)/Dimensions A, DB, E Bore size (mm) 16 20 25 25st 80 95 100.5 50, 75st 71 80 85.5 A DB 100st 125st or more 71 — 8 99 104 10 99.5 104.5 13 OA OB OL P M5 1/8 1/8 PA PB PW Q 40 10 19 16 37.5 10.5 25 18 37.5 13.5 28.5 26 X XA XB YY YL Z 24 28 34 3 3 4 3.5 3.5 4.5 M5 M6 M6 10 12 12 5 17 17 (mm) MXP MG MGP MGQ MGG MGC E 25st 50, 75st 100st 125st or more 9 0 0 — 17 21 2 26 22 26 7 26 MGF MGZ CY MY 3.22-35 Series MGP ø32 to ø63/MGPM, MGPL (With Air Cushion) T-slot dimensions 4-YY depth YL X XAH7 X±0.02 XB a b øXAH7 øXAH7 depth XL XC c XL d e Section XX detail (mm) Bore size (mm) 32 40 50 63 Section XX WB WA HA: T-slot for hexagon bolt Z WA X X ±0.02 øDB PW R T Section XX U Z VB VA X ±0.02 For ø40 4-NN through 4-øOA through 4-øOB depth of counter bore OL øDA L 9.5 11 13.5 18.5 2-cushion valve (width across flats CV) H 4-MM depth ML Section XX e d 3.5 4 4.5 7 c 5.5 5.5 7.5 10 b 10.5 10.5 13.5 17.8 a 6.5 6.5 8.5 11 GC GA øXAH7 depth XL 2-P (plug) PB J øXAH7 depth XL 2-P GB Q PA Stroke K FA FB G S C + Stroke B + Stroke A + Stroke E Refer to "Manufacture of Intermediate Strokes" on page 3.22-23 for intermediate strokes. MGPM, MGPL Common dimensions Bore size Standard stroke B (mm) (mm) CV DA FA FB G GA GB GC 62.5 69 69 74 1.5 1.5 2.5 2.5 16 16 20 20 12 12 16 16 48 54 64 78 12.5 9 14 10 14 11 16.5 13.5 Bore size Standard stroke R (mm) (mm) S T U VA VB 96 25, 50, 75, 104 100, 125, 150, 175, 200 130 130 44 44 60 70 32 40 50 63 32 40 50 63 25, 50, 75, 100, 125, 150, 175, 200 84.5 91 97 102 C (mm) 10 10 12 12 110 78 98 63 118 86 106 72 146 110 130 92 158 124 142 110 MGPM (slide bearing)/Dimensions A, DB, E A Bore size (mm) 25st 50st 75st or more 32 97 127 102 40 97 127 102 50 106.5 131.5 118 63 106.5 131.5 118 3.22-36 DB 25st 20 12.5 20 6 25 9.5 25 4.5 12.5 14 12 16.5 WA 25, 50, 75st 100 to 175st 48 124 48 124 48 124 52 128 (mm) E 50st 75st or more 17.5 42.5 11 36 21 34.5 16 29.5 H HA J K L MM ML NN OA OB OL 112 120 148 162 M6 M6 M8 M10 24 27 32 39 24 27 32 39 34 40 46 58 M8 M8 M10 M10 20 20 22 22 M8 M8 M10 M10 6.6 6.6 8.6 8.6 200st 200 200 200 200 WB 25, 50, 75st 100 to 175st 45 83 46 84 48 86 50 88 200st 121 122 124 124 X 42 50 66 80 11 11 14 14 7.5 7.5 9 9 A 50st 75st 98 123 98 123 127.5 114 127.5 114 100st 125st or more 118 115.5 118 115.5 134 159 134 159 DB 16 16 20 20 25st 0 0 0 0 1/8 1/8 1/4 1/4 XA XB XC XL 4 4 5 5 4.5 4.5 6 6 3 3 4 4 MGPL (ball bushing)/Dimensions A, DB, E Bore size (mm) 25st 32 84.5 40 91 50 97 63 102 P 6 6 8 8 PA PB PW Q 15 18 21.5 28 30 30 40 50 32 38 34 39 YY YL Z M8 M8 M10 M10 16 16 20 20 21 22 24 24 (mm) 50st 38.5 32 30.5 25.5 E 75st 13.5 7 17 12 34 38 47 55 100st 125st or more 33.5 31 27 24.5 37 62 32 57 Compact Guide Cylinder Series With Air Cushion MGP ø80, ø100/MGPM, MGPL (With Air Cushion) T-slot dimensions a b 4-YY depth YL ø6H7 depth 10 ø6 H7 CL X ±0.02 X 7 ø6H7 c d MLG e CNA 5 10 (mm) Bore size (mm) Section XX detail 80 100 WB Section XX HA: T-slot for hexagon bolt Z 4-MM depth ML Section XX L a 13.3 15.3 b 20.3 23.3 c 12 13.5 d 8 10 e 22.5 30 WA MNB CNS CLS 2-cushion valve (width across flats 4) CB 4-øOA through 4-øOB depth of counter bore 8 Z CNG CV/MVG 4-NN through WA Section XX CXW R X ±0.02 T U CXT PW X øDA H VA VB X ±0.02 CXS øDB MX GC GA ø6 H7 depth 10 PB 2-Rc 3/8 (plug) MXU FA FB JA J MXH ø6 H7 depth 10 Q PA + Stroke 10 JB 2- 3/8 GB C + Stroke B + Stroke A + Stroke K G MXS S E MXQ MXF Refer to "Manufacture of Intermediate Strokes" on page 3.22-23 for intermediate strokes. MXW MGPM, MGPL Common dimensions Bore size (mm) Standard stroke (mm) B C DA 121.5 81.5 25 141 91 30 80 100 50, 75, 100, 125, 150, 175, 200 Bore size (mm) Standard stroke (mm) Q R 80 100 50, 75, 100, 125, 150, 175, 200 52 64 174 210 80 100 A DB 50st 75st or more 167 142 30 187 162 36 FA FB G 22 25 18 91.5 25 111.5 L MM ML NN OA OB PA PB PW MXP 19 15.5 14.5 202 M12 45.5 38 7.5 46 54 23 19 18 240 M14 55.5 45 10.5 56 62 M12 M14 25 31 M12 M14 10.6 17.5 39.5 25.5 74 12.5 20 42.5 32.5 89 MG GA GB GC H HA WA VB 50, 75st 100 to 175st 75 198 156 180 140 52 128 90 236 188 210 166 72 148 S MGPM (slide bearing)/Dimensions A, DB, E Bore size (mm) (mm) T U (mm) E 50st 75st or more 45.5 20.5 46 21 VA J JA JB 200st 200 220 K WB 50, 75st 100 to 175st 54 92 47 85 MGPL (ball bushing)/Dimensions A, DB, E Bore size (mm) 80 100 A DB 50st 75st or more 160 168.5 25 180 178.5 30 50st 47 37.5 200st 128 121 X YY YL Z MGP 100 124 M12 M14 24 28 28 11 MGQ MGG (mm) E 75st or more 38.5 39 MGC MGF MGZ CY MY 3.22-37 3.22-38 Compact Guide Cylinder: With End Lock Series MGP ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 CL How to Order MLG Compact Guide Cylinder 100 MGP M 32 Z73 H N CNA Compact guide cylinder Number of auto switches Bearing type M L 2 pcs. 1 pc. Nil S Slide bearing Ball bushing MNB CNS Auto switch type Without auto switch (built-in magnet cylinder) Nil ∗ Refer to the table below for auto switch model numbers. Bore size 20 25 32 40 50 63 80 100 20mm 25mm 32mm 40mm 50mm 63mm 80mm 100mm CV/MVG CXW Lock position Thread Port Rear lock Front lock CXS CXT Cylinder stroke (mm) Rc(PT) TF Non-locking type Locking type H R CLS CB Manual release type N L CNG Refer to the standard stroke table on page 3.22-40. G(PF) MX MXU Applicable auto switches Load voltage Type Special function Electrical Indicator entry light Wiring (output) 3 wire Reed switch DC — 5V — — Z76   — IC circuit — Grommet 12V 100V — Z73    — 2 wire 5V 12V 100V or less — Z80   — IC circuit Y69A Y59A    Y7PV Y7P    Y69B Y59B    Y7NWV Y7NW    Y7PWV Y7PW    Y7BWV Y7BW    — Y7BA —   — P5DW —   24V 3 wire (NPN) 5V 12V 3 wire (PNP) — 2 wire Diagnostic indication (2 colour indicator) Grommet Yes 3 wire (NPN) 3 wire (PNP) 12V 24V 5V 12V — Magnetic field resistant (2 colour indicator) 2 wire Note 3) — MXS MXQ Relay, PLC MXF MXW IC circuit MXP — MG IC circuit Relay, PLC MGP MGQ MGG 12V Water resistant (2 colour indicator) MXH — Yes No Solid state switch AC Lead wire length (m) Note 1) Auto switch model Electrical entry direction Applicable load 0.5 3 5 (Nil) (L) (Z) Perpendicular In-line — MGC MGF Note 1) Lead wire symbols 0.5m ...... Nil (Example) Y69B 3m ......... L Y69BL 5m ......... Z Y69BZ Note 2) Solid state auto switches marked with a "" are produced upon receipt of order. Note 3) Type D-P5DW cannot be mounted on bore sizes of ø32 or less. MGZ CY MY 3.22-39 Series MGP Specifications Double acting Action Fluid Proof pressure Maximum operating pressure Minimum operating pressure Ambient and fluid temperature Air 1.5MPa 1.0MPa 0.15MPa ∗ –10 to 60°C (with no freezing) Piston speed ø20 to ø63 50 to 500mm/s ø80, ø100 50 to 400mm/s Cushion Lubrication Stroke length tolerance Rubber bumper at both ends Non-lube +1.5 0 mm ∗ 0.1MPa except for the lock unit. Lock Specifications Lock position Holding force (max.) N ø20 ø25 ø32 215 330 550 Backlash Manual release Rear, Front side ø40 ø50 ø63 ø80 ø100 860 1340 2140 2mm or less Non-locking type, Locking type 3450 5390 Adjust switch positions for operation at both the stroke end and backlash (2mm) movement positions. Standard Strokes Bore size (mm) 20, 25, 32, 40, 50, 63, 80, 100 Standard stroke (mm) 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400 Manufacture of Intermediate Strokes Spacer installation type Spacers are installed in a standard stroke cylinder. Available in 5mm stroke increments Part number Refer to page 35 for standard part numbers and ordering procedure. Applicable stroke (mm) 5 to 395 Part no.: MGPM50–35–HN A spacer 15mm in width is installed in a MGPM50–50–HN. C dimension is Example 119mm. Modification method Note 1) The minimum stroke for mounting auto switches is 10mm or more for two switches, and 5mm or more for one switch. Note 2) Intermediate strokes (in 1mm increments) with a special body are available by special order. Auto switch mounting bracket part no. for D-P5DW Bore size (mm) 40, 50, 63, 80, 100 Mounting bracket part no. Theoretical Output OUT Notes Switch mounting bracket Hexagon socket head cap screw (M2.5 x 8 l ) 2 pcs. BMG1-040 Hexagon socket head cap screw (M3 x 16 l ) 2 pcs. Spring washer (nominal size 3) (N) Bore size Rod Operating Piston area size (mm²) (mm) (mm) direction 20 25 32 40 50 63 80 100 10 12 16 16 20 20 25 30 Operating pressure (MPa) 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 OUT 314 63 94 126 157 188 220 251 283 314 IN 236 47 71 94 118 142 165 189 212 236 OUT 491 98 147 196 246 295 344 393 442 491 IN 378 76 113 151 189 227 265 302 340 378 OUT 804 161 241 322 402 482 563 643 724 804 IN 603 121 181 241 302 362 422 482 543 603 OUT 1257 251 377 503 629 754 880 1006 1131 1257 634 739 IN 1056 211 317 422 528 OUT 1963 393 589 785 982 1178 1374 1570 1767 1963 660 825 845 950 1056 IN 1649 330 495 OUT 3117 623 935 1247 1559 1870 2182 2494 2805 3117 561 841 1121 1402 1682 1962 2242 2523 2803 IN 2803 OUT 5027 990 1154 1319 1484 1649 1005 1508 2011 2514 3016 3519 4022 4524 5027 IN 4536 907 1361 1814 2268 2722 3175 3629 4082 4536 OUT 7854 1571 2356 3142 3927 4712 5498 6283 7069 7854 IN 7147 1429 2144 2859 3574 4288 5003 5718 6432 7147 Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm²) 3.22-40 IN Compact Guide Cylinder With End Lock Series MGP Weights Slide bearing: MGPM20 to 100 (Basic weight) (kg) Standard stroke (mm) Bore size (mm) Model 25 50 75 20 MGPM20 0.86 1.12 1.32 1.52 1.71 1.91 2.11 2.31 2.78 3.18 3.57 3.97 25 MGPM25 1.18 1.56 1.83 2.10 2.38 2.65 2.92 3.19 3.85 4.39 4.94 5.48 32 MGPM32 1.92 2.32 2.70 3.09 3.47 3.85 4.23 4.61 5.56 6.32 7.09 7.85 40 MGPM40 2.20 2.66 3.08 3.51 3.93 4.36 4.78 5.20 6.24 7.10 7.95 8.80 50 MGPM50 3.73 4.46 5.10 5.74 6.38 7.02 7.66 8.30 63 MGPM63 4.61 5.45 6.21 6.96 7.72 8.47 9.23 9.99 80 MGPM80 100 MGPM100 8.70 7.88 9.49 13.2 12.1 100 14.4 125 150 175 200 250 9.91 300 350 400 11.2 12.5 13.8 11.8 13.3 14.8 16.3 10.3 11.2 12.0 12.8 13.9 15.5 17.2 18.8 20.5 15.6 16.8 18.0 19.1 20.6 22.9 25.3 27.6 30.0 Ball bushing: MGPL20 to 100 (Basic weight) (kg) Standard stroke (mm) Bore size (mm) Model 20 25 25 50 75 MGPL20 0.93 1.10 1.27 1.48 1.65 1.83 2.00 2.17 2.55 2.90 3.25 3.60 MGPL25 1.27 1.50 1.74 2.01 2.24 2.47 2.70 2.94 3.44 3.91 4.37 4.83 32 MGPL32 1.74 2.19 2.51 2.88 3.20 3.51 3.83 4.15 4.84 5.47 6.10 6.73 40 MGPL40 2.02 2.51 2.87 3.29 3.65 4.01 4.37 4.73 5.51 6.23 6.95 7.67 50 MGPL50 3.46 4.21 4.76 5.40 5.95 6.50 7.05 7.60 63 MGPL63 4.33 5.20 5.86 6.62 7.28 7.95 8.61 9.27 80 MGPL80 100 MGPL100 8.87 8.05 9.66 13.5 12.4 100 14.7 125 150 175 200 8.83 300 9.92 350 400 11.1 12.2 10.7 12.1 13.4 14.7 10.5 11.4 12.2 13.0 14.1 15.7 17.4 19.0 20.7 15.9 17.1 18.3 19.4 20.9 23.2 25.6 27.9 30.3 Lock unit additional weight With rear lock 250 With rear lock With front lock HN HL RN RL 63 0.36 0.40 0.35 0.39 0.07 80 0.90 0.97 1.03 1.10 0.10 100 1.52 1.60 1.60 1.68 With front lock HN HL RN RL Bore size (mm) 20 0.05 0.07 0.05 0.06 25 0.06 0.07 0.05 32 0.09 0.10 0.09 40 0.15 0.18 0.14 0.18 50 0.24 0.27 0.23 0.27 CNA CNG MNB CNS CLS CB CV/MVG CXS CXT MX MXU Calculation (example) MGPM50-100-HN • Basic weight + Lock unit additional weight • 5.74 + 0.24 = 5.99kg Allowable Rotational Torque of Plate MLG CXW (kg) Bore size (mm) CL Non-rotating Accuracy of Plate MXH MXS Torque: T (N⋅m) +θ –θ MXQ MXF T (N⋅m) Bore size (mm) 20 25 32 40 50 63 80 100 Stroke (mm) Bearing type 25 50 75 MGPM 0.99 0.75 1.88 100 1.63 125 1.44 150 1.28 175 1.16 200 250 300 350 400 1.06 0.90 0.78 0.69 0.62 For non-rotating accuracy θ without load, use a value no more than the values in the table as a guide. Bore size (mm) MGPL 2.66 1.94 1.52 1.25 1.34 1.17 1.03 0.93 0.76 0.65 0.56 0.49 MGPM 1.64 1.25 2.96 2.57 2.26 2.02 1.83 1.67 1.42 1.24 1.09 0.98 20 MGPL 4.08 3.02 2.38 1.97 2.05 1.78 1.58 1.41 1.16 0.98 0.85 0.74 25 MGPM 6.35 5.13 5.69 4.97 4.42 3.98 3.61 3.31 2.84 2.48 2.20 1.98 32 MGPL 5.95 4.89 5.11 4.51 6.34 5.79 5.33 4.93 4.29 3.78 3.38 3.04 40 MGPM 7.00 5.66 6.27 5.48 4.87 4.38 5.98 3.65 3.13 2.74 2.43 2.19 50 63 MGPL MGPM MGPL 6.55 13.0 9.17 MGPM 14.7 5.39 10.8 7.62 12.1 5.62 12.0 9.83 13.5 4.96 10.6 6.98 6.38 5.87 5.43 4.72 4.16 3.71 3.35 9.50 8.60 7.86 7.24 6.24 5.49 4.90 4.43 80 9.83 9.12 7.95 7.02 6.26 5.63 100 8.86 8.16 7.04 6.19 5.52 4.99 6.94 6.24 8.74 11.6 11.9 10.7 10.7 9.69 MGPL 10.2 11.9 11.0 10.2 MGPM 21.9 18.6 22.9 20.5 18.6 17.0 15.6 14.5 12.6 11.2 10.0 8.48 11.0 9.74 13.0 8.84 7.80 Non-rotating accuracy θ MGPM MGPL ±0.07° ±0.09° ±0.06° ±0.08° ±0.05° ±0.06° ±0.04° ±0.05° MGPL 15.1 23.3 22.7 20.6 18.9 17.3 16.0 14.8 12.9 11.3 10.0 38.8 33.5 37.5 33.8 30.9 28.4 26.2 24.4 21.4 19.1 17.2 15.7 MGPL 27.1 30.6 37.9 34.6 31.8 29.3 27.2 25.3 22.1 19.5 17.3 15.5 MXP MG MGP MGQ MGG MGC MGF 9.11 MGPM MXW 8.94 MGZ CY Model selection is the same as MGP/Standard. Refer to page 3.22-8. MY 3.22-41 Series MGP Auto Switches/Proper Mounting Position for Stroke End Detection For D-P5DW ø40 to ø63 With rear lock Auto switch 16.5 Auto switch A B (∗ Cannot be mounted on bore sizes ø32 or less.) 16.5 With front lock A Hs B Hs For 25mm stroke Bore size (mm) 20 25 32 40 50 63 80 100 A 47.5 35.5 32.5 38.5 38.5 42 63 67.5 B 1.5 1.5 5 5.5 4.5 7 18.5 23.5 ∗ Minimum mountable strokes for auto switch are 10mm or more for two switches, and 5mm or more for one switch. (mm) Bore size (mm) 20 25 32 40 50 63 80 100 A 4 5 5.5 9.5 7.5 10 13 17.5 B 33 32.5 32 34.5 36.5 39 68.5 73.5 ø80, ø100 Ht Proper mounting position (mm) ∗ For bore sizes ø40 through 63 with two switches, one switch is mounted on each side. ∗ Minimum mountable strokes for auto switch are 10mm or more for two switches, and 5mm or more for one switch. Hs (mm) Bore size (mm) 40 50 63 80 100 Hs 44.5 50 57 60.7 70.8 Ht — — — 84.4 96.1 ∗ Minimum mountable strokes for auto switch are 10mm or more for two switches, and 5mm or more for one switch. Auto Switch Mounting For D-P5DW Caution Caution Auto switch mounting tool Auto switch mounting tool • When tightening the auto switch mounting screw (included with auto switch), use a watchmakers screw driver with a handle about 5 to 6mm in diameter • When tightening hexagon socket head cap screws of the auto switch, use hexagon wrench key 2 or 2.5 with the appropriate screws. Tightening torque • Tighten with a torque of 0.05 to 0.1N⋅ m. As a rule, it should be turned about 90° past the point at which tightening can be felt. Flat head watchmakers screw driver Switch mounting screw (M2.5 x 4 l ) (included with auto switch) Auto switch Tightening torque • Tighten M2.5 screws with a torque of about 0.3 to 0.5N⋅ m, and M3 screws with a torque of about 0.5 to 0.7 N⋅ m. Hexagon wrench key 2 Hexagon socket head cap screw (M2.5 x 8 l ) When mounting an auto switch on the side with the end lock, insert the auto switch from the rod side for the rear lock, and from the head side for the front lock. Hexagon wrench key 2.5 Hexagon socket head cap screw (M3 x 16 l ) 3.22-42 Auto switch Compact Guide Cylinder With End Lock Series MGP Construction Series MGPL Series MGPM CL ø20, ø25: 75mm stroke or less ø32 to ø63: Over 25 to 75mm stroke ø80, ø100: 150mm stroke or less ø20, ø25: 25mm stroke MLG CNA CNG ø32 to ø63: 25mm stroke MNB ø20 to ø63: Over 75mm stroke ø80, ø100: Over 150mm stroke ø50 or larger CNS ø50, ø63 Locking type Non-locking type CLS (Rear side lock) CB CV/MVG CXW ø20 to ø63 ø80, ø100 CXS (With front lock) CXT MX ø20 to ø63 ø80, ø100 Parts list MXU Parts list Note Material Hard anodized Aluminum alloy Chromated Aluminum alloy Stainless steel ø20, ø25 Hard chrome plated with front end lock only 3 Piston rod Hard chrome plated Carbon steel ø32 to ø100 Clear anodized Aluminum alloy 4 Collar Lead bronze casting 5 Bushing Colorless chromated Aluminum alloy 6 Head cover Hard chrome plated Carbon steel 7 Guide rod Nickel plated Carbon steel 8 Plate Nickel plated Carbon steel 9 Plate mounting bolt Phosphate coated Carbon tool steel 10 Snap ring Phosphate coated Carbon tool steel 11 Snap ring Urethane 12 Bumper A Urethane 13 Bumper B Synthetic rubber 14 Magnet Nickel plated Carbon steel 15 Hexagon socket head taper plug Lead bronze casting 16 Slide bearing Felt 17 Felt Resin 18 Holder 19 Ball bushing Aluminum alloy 20 Spacer NBR 21∗ Piston seal 22∗ 23 ∗ 24 ∗ 25 26 27 28 29 30 31 32∗ 33 ∗ 34 35 36 37 38 39 40 41∗ 42∗ Replacement parts: Seal kits Replacement parts: Seal kits No. 1 2 Description Body Piston Bore size (mm) 20 25 32 40 50 Kit No. Contents MGP20-B-PS MGP25-B-PS Kits include items MGP32-B-PS 21, 22, 23, 24, 32, 33, 41 and 42 MGP40-B-PS from the table above. MGP50-B-PS ∗ Seal kits are sets consisting of items 21 through 24, 32, 33, 41 and 42 above, and can be ordered using the kit number for each bore size. No. Description Rod seal Gasket A Gasket B Piston gasket Lock bolt Lock holder Lock piston Lock spring Seal retainer Bumper Note Material NBR NBR NBR ø32 to ø100 only NBR Zinc chromated Carbon steel Electroless nickel plated Brass Nickel plated Carbon steel Stainless steel Zinc chromated (ø80, ø100 only) Carbon steel Urethane Black zinc chromated Hexagon socket head cap screw Carbon steel Nickel plated (ø50, ø63 only) Hexagon socket head cap screw Carbon steel Black coated Cap A Die-cast aluminum SQ treated Cap B Carbon steel Rubber cap Synthetic rubber Black coated M/O knob Die-cast zinc Black zinc chromated M/O bolt Alloy steel Chromated M/O spring Steel wire Chromated Stopper ring Carbon steel Lock piston seal NBR Lock holder gasket NBR Bore size (mm) Kit no. MXH MXS MXQ MXF MXW MXP MG MGP MGQ MGG MGC Contents MGF 63 MGP63-B-PS Kits include items 21, 22, 23, 24, 32, 33, 41 and 42 80 MGP80-B-PS from the table above. 100 MGP100-B-PS ∗ Items 32 and 33 are not included for bores sizes 80 and 100. MGZ CY MY 3.22-43 Series MGP ø20, ø25 Dimensions/ 4-MM depth ML L 17 X U PW øDB PB WB WA Section XX 4-NN through øDA VB VA H End lock mechanism non-locking type manual release øXAH7 depth 6 WA 24 X ±0.02 15 ø11 X X ±0.02 Section XX 17 T R X ±0.02 4-M6 x 1.0 depth 2 M5:T-slot for hexagon bolt Section XX 4-ø5.6 through 4-ø9.5 depth of counter bore 5.5 J 2- 1/8 (plug) HR GA DL øXAH7 depth 6 10 6 G Q GB 37.5 + Stroke C + Stroke K S øXAH7 depth 6 E B + Stroke A + Stroke 2- 1/8 3 XAH7 HN 24 4.5 d e End lock mechanism T-slot dimensions (mm) (Locking type manual release) 24 6 5.4 8.4 ø15 XB øXAH7 With front lock Section XX detail 15 For ø25 DM Bore size (mm) d e 20 2.8 7.8 25 3 8.2 With rear lock Refer to "Manufacture of Intermediate Strokes" on page 3.22-40 for intermediate strokes. (mm) Bore size (mm) Standard stroke (mm) B 20 25, 50, 75, 100, 125, 150, 175 200, 250, 300, 350, 400 25 Q R 10.5 25 18 70 13.5 28.5 26 78 DA G GA GB H J K L MM ML NN PB 78 62 10 36 10.5 8.5 83 18 18 24 M5 13 M5 78.5 62.5 12 42 11.5 9 93 21 21 30 M6 15 M6 (mm) WA WB Bore size (mm) S T U VA VB 20 30 81 54 72 44 44 120 200 300 39 77 117 25 38 91 64 82 50 44 120 200 300 39 77 117 End lock mechanism dimensions (mm) X XA XB 167 28 3 3.5 167 34 4 4.5 Over 75st Over 175st Over 250st 75st or less Over 75st Over 175st Over 250st 75st or less to 175st to 250st to 175st to 250st MGPM (slide bearing)/Dimensions A, DB, E Bore size (mm) DL DM HR HN 20 21 19 10.5 22 20 25 26.5 16 8 19.5 25 Bore size (mm) A Over 75st to 175st Over 175st 78 84.5 122 78.5 85 122 75st or less DB Bore size (mm) 25st or less A Over 25st to 175st Over 175st (mm) E 75st or less Over 75st to 175st 12 0 6.5 44 16 0 6.5 43.5 MGPL (ball bushing)/Dimensions A, DB, E 3.22-44 PW C DB Over 175st (mm) E 25st or less Over 25st to 175st Over 175st 20 80 104 122 10 2 26 44 25 85.5 104.5 122 13 7 26 43.5 Compact Guide Cylinder MGP Series With End Lock ø32 to ø63 Dimensions/ 4-MM depth ML 4-YY depth YL HA: T-slot for hexagon bolt Section XX L Section XX 4-NN through WA CL T R X ±0.02 PW X U øDA MLG CNA øDB VA H VB X ±0.02 24 11 ) PB J K G Z HR øXAH7 CNG GC GA LL GB PA + Stroke depth XL C + Stroke FA FB B + Stroke A + Stroke 2-P E øXAH7 XB øMO c CB T-slot dimensions (mm) HN End lock mechanism (Locking type manual release) Section XX detail d e DM XL CNS CLS b With front lock XAH7 XC MNB Q S øXAH7 depth XL a X X ±0.02 ( WB WA Z Section XX DL End lock mechanism non-locking type manual release 2-P (plug) øXAH7 depth XL 4-øOA through 4-øOB depth of counter bore OL e CXW 9.5 CXS Bore size (mm) a b c d 32 6.5 10.5 5.5 3.5 40 6.5 10.5 5.5 4 11 8.5 13.5 7.5 4.5 13.5 7 18.5 50 63 11 17.8 10 CV/MVG CXT LL MX With rear lock Bore size Standard stroke (mm) (mm) 32 40 50 63 B 25, 50, 75, 100 84.5 91 125, 150, 175 200, 250, 300 97 350, 400 102 (mm) C DA FA FB G GA GB GC H HA J K L MM ML NN OA MXU 9 MXH 62.5 16 12 10 48 12.5 12.5 112 M6 24 24 34 M8 20 M8 6.6 69 16 12 10 54 14 10 14 120 M6 27 27 40 M8 20 M8 6.6 69 20 16 12 64 14 11 12 148 M8 32 32 46 M10 22 M10 8.6 74 20 16 12 78 16.5 13.5 16.5 162 M10 39 39 58 M10 22 M10 8.6 (mm) Bore size (mm OB 32 11 40 OL WA WB P PA PB PW Q R S T U VA VB 7.5 1/8 32 15 34 30 96 44 110 78 98 63 48 124 200 300 45 83 121 171 11 7.5 1/8 38 18 38 30 104 44 118 86 106 72 48 124 200 300 46 84 122 172 50 14 9 1/4 34 21.5 47 40 130 60 146 110 130 92 48 124 200 300 48 86 124 174 63 14 9 1/4 39 28 55 50 130 70 158 124 142 110 52 128 200 300 50 88 124 174 (mm) Bore size (mm) X XA XB XC XL YY YL 32 42 4 4.5 3 6 M8 40 50 4 4.5 3 6 50 66 5 6 4 8 63 80 5 6 4 8 M10 32 22 22 40 26 23 50 24 23 63 25 25.5 11 DM HN A 25st or less 16 21 32 97 102 140 20 12.5 M8 16 22 40 97 102 140 20 6 11 49 M10 20 24 50 106.5 118 161 25 9.5 21 64 20 24 63 106.5 118 161 25 4.5 16 59 Bore size (mm) 21 15 15 32 84.5 11.5 25.5 21 19 40 13 27 21 19 50 25 21 19 63 9.5 25st or less A MO (max.) Over 25st Over 175st to 175st DB Over 25st Over 175st to 175st 17.5 25st Over 75st 25st or less Over to 175st Over 175st to 75st DB MXQ MXF MXW MXP MG MGP 55.5 MGQ MGG (mm) MGC 25st Over 75st 25st or less Over to 175st Over 175st to 75st MGF MGPL (ball bushing)/Dimensions A, DB, E LL HR (mm) E Z (mm) DL MGPM (slide bearing)/Dimensions A, DB, E Bore size (mm) End lock mechanism Bore size (mm) 75st Over 175st Over 275st 75st or less Over 75st Over175st 75st or less Over to 175st to 275 st to 175st to 275 st Over 275st MXS E 98 118 140 16 0 13.5 33.5 55.5 91 98 118 140 16 0 7 27 49 97 114 134 161 20 0 17 37 64 102 114 134 161 20 0 12 32 59 MGZ CY MY 3.22-45 Series MGP ø80, ø100 Dimensions/ 4-NN through End lock mechanism non-locking type manual release 2- 3/8 (plug) JB ø6H7 depth 10 WB WA øDB PW øDA VB VA H X X ±0.02 40 ø21 HR Section XX X U T R X ±0.02 Section XX L HA: T-slot for hexagon bolt Section XX X ±0.02 4-øOA through 4-øOB depth of counter bore 8 Z WA 30 4-MM depth ML 4-YY depth YL Z PB 10 JA J K G GC 2-Rc 3/8 GA DL PA + Stroke FA FB C + Stroke B + Stroke A + Stroke ø6H7 depth 10 GB Q S E ø6H7 depth 10 ø6 With front lock 7 HN 6H7 5 Section XX detail a b ø23 DM 10 c d e End lock mechanism (Locking type manual release) 30 With rear lock T-slot dimensions (mm) Bore size (mm) a 80 13.3 20.3 12 100 15.3 23.3 13.5 b c d e 8 22.5 10 30 (mm) Standard stroke (mm) Bore size (mm) 80 100 B C 25, 50, 75, 100, 125, 150, 175 146.5 106.5 200, 250, 300, 350, 400 166 116 DA FA FB G GA GB GC H HA J JA 25 22 30 25 18 91.5 19 15.5 14.5 202 M12 45.5 25 111.5 23 19 18 240 M14 55.5 JB K L 38 7.5 46 54 45 10.5 56 62 (mm) WA Bore size (mm) MM ML NN OA OB PA PB PW Q R S T U VA VB 80 M12 25 M12 10.6 17.5 64.5 25.5 74 52 174 75 198 156 180 140 52 128 200 300 100 M14 31 M14 12.5 20 67.5 32.5 89 64 210 90 236 188 210 166 72 148 220 320 50st Over 150st 50st or less Over to 150st to 250st Over 250st (mm) Bore size (mm) WB Over 50st Over 150st 50st or less to 150st to 250st Over 250st X YY YL Z 80 54 92 128 178 100 M12 24 28 100 47 85 121 171 124 M14 28 11 End lock mechanism dimensions (mm) MGPM (slide bearing)/Dimensions/A, DB, E Bore size (mm) DL DM HR HN Bore size (mm) 80 45.5 40.5 24 38.5 80 49 43.5 26.5 41 100 3.22-46 100 A 150st or less Over 150st DB (mm) E 150st or less Over 150st 146.5 193 30 0 46.5 166 203 36 0 37 MGPL (ball bushing)/Dimensions A, DB, E Bore size (mm) A 150st or less Over 150st (mm) E DB 150st or less Over 150st 80 160 193 25 13.5 46.5 100 180 203 30 14 37 Compact Guide Cylinder: Heavy Duty Guide Rod Type Series MGPS ø50, ø80 How to Order CL MLG Compact Guide Cylinder MGP S 50 50 Z73 CNA CNG Compact guide cylinder MNB Number of auto switches CLS Auto switch type Bore size 50 80 CNS 2 pcs. 1 pc. Nil S Heavy duty guide rod type Without auto switch (built-in magnet cylinder) Nil 50mm 80mm ∗ Refer to the table below for auto switch model numbers. CB CV/MVG Cylinder stroke (mm) Refer to the standard stroke table on page 3.22-48. CXW Thread Port CXS Rc(PT) TF G(PF) CXT MX Applicable auto switches Load voltage Type Special function Electrical Indicator entry light Wiring (output) 3 wire Reed switch DC — 5V — — Z76   — IC circuit 12V 100V — Z73    — 5V 12V 100V or less — Z80   — IC circuit Y69A Y59A    Y7PV Y7P    Y69B Y59B    Y7NWV Y7NW    Y7PWV Y7PW    Y7BWV Y7BW    — Y7BA —   — P5DW —   — Yes — Grommet 2 wire 24V No 3 wire (NPN) 5V 12V 3 wire (PNP) — 2 wire Solid state switch AC Lead wire length (m) Note 1) Auto switch model Electrical entry direction Applicable load 0.5 3 5 (Nil) (L) (Z) Perpendicular In-line Diagnostic indication (2 colour indicator) Grommet Yes 3 wire (NPN) 3 wire (PNP) 12V 24V 5V 12V — Relay, PLC Magnetic field resistant (2 colour indicator) 2 wire — MXH MXS MXQ MXF IC circuit MXW MXP — IC circuit Relay, PLC MG MGP 12V Water resistant (2 colour indicator) MXU MGQ — MGG MGC Note 1) Lead wire symbols 0.5m ...... Nil (Example) Y69B 3m ......... L Y69BL 5m ......... Z Y69BZ Note 2) Solid state auto switches marked with a "" are produced upon receipt of order. MGF MGZ CY MY 3.22-47 Series MGPS Specifications Double acting Action Air Fluid Proof pressure 1.5MPa Maximum operating pressure 1.0MPa Minimum operating pressure 0.1MPa –10 to 60°C (with no freezing) Ambient and fluid temperature 50 to 400mm/s Piston speed Rubber bumper at both ends Cushion Lubrication Non-lube Stroke length tolerance +1.5 0 mm Standard Strokes Bore size (mm) Standard stroke (mm) 50, 80 25, 50, 75, 100, 125, 150, 175, 200 Manufacture of Intermediate Strokes Spacer installation type Spacers are installed in a standard stroke cylinder. Available in 5mm stroke increments Refer to page 3.22-47 for standard part numbers and ordering procedure. Modification method Part number Applicable stroke (mm) 5 to 195 Part no.: MGPS50—35 A spacer 15mm in width is installed in a MGPS50—50. C dimension is 94mm. Example Note 1) The minimum stroke for mounting auto switches is 10mm or more for two switches, and 5mm or more for one switch. Note 2) Intermediate strokes (in 1mm increments) with a special body are available by special order. Theoretical Output OUT IN (N) Bore size (mm) Auto switch mounting bracket part no. for D-P5DW Bore size (mm) 50, 80 Mounting bracket part no. BMG1-040 Notes Switch mounting bracket Hexagon socket head cap screw (M2.5 x 8 l ) 2 pcs. Hexagon socket head cap screw (M3 x 16 l ) 2 pcs. Spring washer (nominal size 3) Rod Operating Piston area size (mm) direction (mm²) 0.2 0.3 0.4 0.5 OUT 1963 393 589 785 982 1178 1374 1571 1767 1963 IN 1649 330 495 660 825 OUT 5027 1005 1508 2011 2513 3016 3519 4021 4524 5027 IN 4536 907 1361 1814 2268 2721 3175 3629 4082 4536 50 20 80 25 Operating pressure (MPa) 0.6 0.7 990 1155 1319 1484 1649 Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm²) Weights (kg) Standard stroke (mm) Bore size (mm) Model 25 50 75 100 125 150 175 200 50 MGPS50 3.90 4.68 5.74 6.52 7.30 8.08 8.86 9.64 80 MGPS80 9.21 10.7 Allowable Rotational Torque of Plate 13.0 14.5 15.9 17.9 50 80 3.22-48 20.3 For non-rotating accuracy θ +θ without load, use a value no more –θ than the values in the table as a guide. T (N⋅m) Standard stroke (mm) Model 18.9 Non-rotating Accuracy of Plate Torque: T (N⋅m) Bore size (mm) 1.0 0.9 0.8 25 50 75 100 125 150 175 MGPS50 15 12 16 15 13 12 11 MGPS80 49 41 51 45 41 38 35 200 Bore size (mm) Model Non-rotating accuracy θ 9.8 50 MGPS50 ±0.05° 80 MGPS80 ±0.04° 32 Series MGPS Model Selection Selecting Conditions Vertical Horizontal l CL l m MLG CNA Mounting orientation CNG m MNB CNS Maximum speed (mm/s) Graph (Slide bearing type) 200 400 200 400 1, 2 3, 4 5, 6 7, 8 CLS CB CV/MVG Selection Example 1 (Vertical Mounting) Selection Example 2 (Horizontal Mounting) Selecting conditions Mounting: Vertical Stroke: 50mm Maximum speed: 200mm/s Load weight: 100kg Eccentric distance: 100mm Find the point of intersection for the load weight of 100kg and the eccentric distance of 100mm on graph 1 , based on vertical mounting, 50mm stroke, and the speed of 200mm/s. → MGPS80-50 is selected. Selecting conditions Mounting: Horizontal Distance between plate and load center of gravity: 50mm Maximum speed: 200mm/s Load weight: 30kg Stroke: 100mm Find the point of intersection for the load weight of 30kg and stroke of 100mm on graph 5 , based on horizontal mounting, the distance of 50mm between the plate and load center of gravity, and the speed of 200mm/s. → MGPS80-100 is selected. 1 50mm stroke or less 5 l = 50mm V = 200mm/s CXS CXT MX MXU MXH V= 200mm/s MXS 100 200 CXW MXQ ø80 MXF 100 MXW ø80 50 50 Load weight m (kg) Load weight m (kg) ø80 ø50 MXP 40 MG 30 MGP MGQ ø50 ø50 MGG 20 MGC MGF 10 MGZ 10 10 50 100 Eccentric distance l (mm) 300 10 20 30 40 50 51 100 200 Stroke (mm) CY MY 3.22-49 Series MGPS Vertical Mounting Operating pressure: 0.4MPa Operating pressure: 0.5MPa or more Slide Bearing MGPS50, 80 1 50mm stroke or less 2 Over 50mm stroke V = 200mm/s 300 300 200 200 ø80 ø80 100 50 Load weight m (kg) Load weight m (kg) 100 ø50 40 50 ø50 40 30 30 20 20 10 10 10 50 100 10 200 50 3 50mm stroke or less 100 200 Eccentric distance l (mm) Eccentric distance l (mm) 4 Over 50mm stroke V = 400mm/s 300 300 200 200 V = 400mm/s ø80 ø80 100 50 Load weight m (kg) 100 Load weight m (kg) V = 200mm/s ø50 40 50 40 30 30 20 20 10 ø50 10 10 50 Eccentric distance l (mm) 3.22-50 100 200 10 50 Eccentric distance l (mm) 100 200 Compact Guide Cylinder Series Heavy Duty Guide Rod Type Horizontal Mounting MGPS Slide Bearing MGPS50, 80 5 l = 50mm 6 l = 100mm V = 200mm/s 100 V = 200mm/s 100 CL MLG CNA ø80 50 50 CNG ø80 Load weight m (kg) Load weight m (kg) ø80 40 30 ø80 40 MNB CNS 30 CLS ø50 ø50 20 CB ø50 20 CV/MVG ø50 CXW CXS 10 10 10 20 30 40 50 51 100 200 10 20 30 51 100 200 8 l = 100mm V = 400mm/s 50 CXT MX Stroke (mm) Stroke (mm) 7 l = 50mm 40 50 MXU V = 400mm/s 50 MXH ø80 ø80 40 MXS ø80 ø80 40 MXQ MXF 30 30 Load weight m (kg) Load weight m (kg) MXW 20 MXP MG 20 MGP MGQ MGG ø50 ø50 MGC ø50 ø50 MGF MGZ 10 10 10 20 30 40 50 51 Stroke (mm) 100 200 10 20 30 40 50 51 100 200 CY Stroke (mm) MY 3.22-51 Series MGPS m 2000 MGPS80 υ m 1000 Weight of transfered object: m (kg) υ l: Approx. 50mm l: Approx. 50mm Operating Range when Used as Stopper MGPS50 500 400 300 200 100 ∗ When selecting a model with a longer l dimension, be sure to choose a bore size which is sufficiently large. 50 5 10 20 Transfer speed: υ (m/min) Caution Handling precautions Note) When using as a stopper, select a model with a stroke of 50mm or less. 3.22-52 30 40 50 Compact Guide Cylinder Heavy Duty Guide Rod Type Series MGPS Auto Switches/Proper Mounting Position for Stroke End Detection Auto switch For D-P5DW ø50 CL MLG 16.5 B 16.5 A CNA CNG MNB 53 53 CNS For 25mm stroke Proper mounting position Bore size (mm) 50 80 A 7.5 13 (mm) ∗ For bore sizes ø40 through 63 with two switches, one switch is mounted on each side. ø80 B 11.5 37 CLS CB CV/MVG Note ) Minimum mountable strokes for auto switch are 10mm or more for two switches, and 5mm or more for one switch. 84.4 CXW CXS CXT MX MXU 60.7 MXH Auto Switch Mounting MXS For D-P5DW Caution Caution Auto switch mounting tool Auto switch mounting tool • When tightening the auto switch mounting screw (included with auto switch), use a watchmakers screw driver with a handle about 5 to 6mm in diameter. • When tightening hexagon socket head cap screws of the auto switch, use hexagon wrench key 2 or 2.5 with the appropriate screws. Tightening torque Tightening torque • Tighten with a torque of 0.05 to 0.1N⋅ m. As a rule, it should be turned about 90° past the point at which tightening can be felt. • Tighten M2.5 screws with a torque of about 0.3 to 0.5N⋅ m, and M3 screws with a torque of about 0.5 to 0.7N⋅ m. Flat head watchmakers screw driver Switch mounting screw (M2.5 x 4 l ) MXQ MXF MXW MXP MG Hexagon wrench key 2 Hexagon socket head cap screw (M2.5 x 8 l ) MGP (included with auto switch) Auto switch MGQ MGG MGC MGF MGZ Hexagon wrench key 2.5 Auto switch Hexagon socket head cap screw (M3 x 16 l ) CY MY 3.22-53 Series MGPS Construction Over 50mm stroke 50mm stroke or less Parts list No. Parts list 1 2 3 4 5 Description Body Piston Piston rod Collar Bushing 6 Head cover 7 8 9 10 Guide rod Plate Plate mounting bolt A Plate mounting bolt B Note Hard anodized Chromated Hard chrome plated Coated Material Aluminum alloy Aluminum alloy Carbon steel Aluminum alloy casting Lead bronze casting Aluminum alloy Carbon steel Carbon steel Carbon steel Carbon steel ø50 ø80 Colorless chromated Coated Hard chrome plated Nickel plated Nickel plated For piston rod Nickel plated For guide rod Replacement parts: Seal kits Bore size (mm) Kit no. Contents 50 80 MGP50-PS MGP80-PS Kits include items 17, 18, 19 and 20 from the table above. ∗ Seal kits are sets consisting of items 17 through 20 above, and can be ordered using the kit number for each bore size. 3.22-54 No. 11 12 13 14 15 16 17 ∗ 18 ∗ 19 ∗ 20 ∗ Description Material Note Carbon tool steel Phosphate coated Snap ring Urethane Bumper A Urethane Bumper B Synthetic rubber Magnet Carbon steel Nickel plated Hexagon socket head taper plug Lead bronze casting Slide bearing NBR Piston seal NBR Rod seal NBR Gasket A NBR Gasket B Compact Guide Cylinder Series Heavy Duty Guide Rod Type MGPS Dimensions øXAH7 depth XL MGPS50/80 T-slot dimensions a b 4-YY depth YL CL XAH7 X RA X ± 0.02 øXAH7 RB XB MLG c CNA d CNG e XC (mm) XL Bore size (mm) Section XX detail 50 80 8-RR depth RL Section XX T-slot dimensions e d c b a 17.5 6 17.8 10 11 22.5 8 13.3 20.3 12 WB QA QB Z WA Z WA CLS CV/MVG 4-øOA through 4-øOB depth of counter bore OL HA T-slot for hexagon bolt Section XX CXW 4-NN depth NL CXS MX X ±0.02 X X T øDA MXU PW U H CXT VA VB X ±0.02 L CNS CB Section XX 4-MM depth ML MNB MXH øDB MXS 2-P (plug) PB J K MXQ GC øXAH7 depth XL GA G FB GB MXF S 2-P PA + Stroke FA øXAH7 depth XL Q MXW C + Stroke Refer to "Manufacture of Intermediate Strokes" on page 3.22-48 for intermediate strokes other than the standard strokes. E B + Stroke A + Stroke Dimensions (mm) A Bore size Standard stroke B (mm) (mm) 25, 50st Over 50st 86 110 86 50 25, 50, 75, 100, 125, 150, 175, 200 118 151 118 80 Bore size Standard stroke (mm) (mm) 50 80 25, 50, 75, 100, 125, 150 ,175, 200 Bore size Standard stroke (mm) (mm) 50 80 25, 50, 75, 100, 125, 150, 175, 200 Bore size Standard stroke (mm) (mm) 50 80 25, 50, 75, 100, 125, 150, 175, 200 C DA DB 44 65 20 25 30 45 E FA 25, 50st Over 50st 0 24 30 0 33 35 OB OL MM ML NN NL OA M12 M16 20 32 M10 M12 20 24 10.6 17.5 13 17.5 12.5 20 S T U VA VB 50 65 156 228 116 170 140 214 100 138 YY YL Z M12 M14 24 28 24 28 25st 24 28 P 1/4 3/8 WA 50, 75, 100st Over 100st 124 48 128 52 PA FB G GA GB GC 12 18 72 95 14 19 11 24 12 160 14.5 242 PB 24.5 9 14.5 29 25st 36 42 H HA J K L M10 M12 35 47 37 48 50 66 PW Q QA QB RA RB RR RL 50 77 32 40 16 18 7 9 48 80 140 200 M8 M10 14 20 WB X 50, 75, 100st Over 100st 48 86 68 54 92 100 XA XB XC XL 5 6 6 7 4 5 8 10 MXP MG MGP MGQ MGG MGC MGF MGZ CY MY 3.22-55 MGP Order Made Specifications Series Contact SMC for detailed specifications and lead times, and for applications of cylinders with air cushion, heavy duty guide rod type, and lock type. Symbol Order made specification Order made specification Intermediate stroke (special body type) -XB10 With heavy duty scraper With air cushion/Intermediate stroke (spacer installed type) -XC19 With coil scraper Symbol -XC4 -XC35 -XB6 Adjustable stroke cylinder/Adjustable extension type -XC8 Low speed cylinder -XB13 Adjustable stroke cylinder/Adjustable retraction type -XC9 Fluoro rubber seal -XC22 Stainless steel used for piston rod, plate, etc. -XC6 Heat resistant cylinder -XB10 1 Intermediate Strokes (Special Body Type) MGP ML Bore size Stroke Stroke ranges XB10 Bore size (mm) Intermediate stroke When using an intermediate stroke, the overall length of the cylinder can be shortened by using a special body without the installation of spacers. Stroke range (mm) 12, 16 10 to 250 20, 25 20 to 400 32, 40, 50, 63, 80, 100 25 to 400 ∗ Specifications other than the stroke range are the same as standard products. WB WA E A + Stroke Dimensions MGPM, MGPL-XB10/Dimensions WA, WB Bore size (mm) Standard stroke (mm) 12 16 10 to 250 Bore size (mm) Standard stroke (mm) 20 25 20 to 400 Bore size (mm) Standard stroke (mm) 32 40 50 63 80 100 25 to 400 (mm) WA 40 to 100st 101 to 200st 40 110 44 110 10 to 39st 20 24 12 16 Bore size (mm) 20 25 Bore size (mm) 32 40 50 63 80 100 10 to 39st 15 17 40 to 100st 25 27 101 to 200st 60 60 201 to 250st 105 105 40 to 124st 44 44 WA 125 to 200st 120 120 201 to 300st 200 200 301 to 400st 300 300 20 to 39st 29 29 WB 40 to 124st 125 to 200st 39 77 39 77 201 to 300st 117 117 301 to 400st 167 167 25 to 49st 24 24 24 28 28 48 WA 50 to 124st 125 to 200st 48 124 48 124 48 124 52 128 52 128 72 148 201 to 300st 200 200 200 200 200 220 301 to 400st 300 300 300 300 300 320 25 to 49st 33 34 36 38 42 35 WB 50 to 124st 125 to 200st 45 83 46 84 48 86 50 88 54 92 47 85 201 to 300st 121 122 124 124 128 121 301 to 400st 171 172 174 174 178 171 (mm) A E 10 to 74st 75 to 100st 101 to 250st 10 to 74st 75 to 100st 101 to 250st 42 60.5 85 0 18.5 43 46 64.5 95 0 18.5 49 MGPL (ball bushing)/Dimensions A, E Bore size (mm) 12 16 A E 20 to 74st 75 to 200st 201 to 400st 20 to 74st 75 to 200st 201 to 400st 53 84.5 122 0 31.5 69 53.5 85 122 0 31.5 68.5 Bore size (mm) A E 25 to 74st 75 to 200st 201 to 400st 25 to 74st 75 to 200st 201 to 400st 97 102 140 37.5 42.5 80.5 97 102 140 31 36 74 106.5 118 161 34.5 46 89 106.5 118 161 29.5 41 84 115 142 193 18.5 45.5 96.5 137 162 203 21 46 87 Bore size (mm) ∗ Dimensions other than those in the above tables are the same as standard products. 3.22-56 201 to 250st 200 200 20 to 39st 24 24 MGPM (slide bearing)/Dimensions A, E Bore size (mm) WB 20 25 32 40 50 63 Bore size (mm) 80 100 10 to 39st 43 49 A 40 to 100st 101 to 250st 10 to 39st 55 85 1 65 95 3 (mm) E 40 to 100st 101 to 250st 13 43 19 49 A E 20 to 39st 40 to 124st 125 to 200st 201 to 400st 20 to 39st 40 to 124st 125 to 200st 201 to 400st 80 63 104 122 10 27 51 69 85.5 69.5 104.5 122 16 32 51 68.5 A E 25 to 74st 75 to 124st 125 to 200st 201 to 400st 25 to 74st 75 to 124st 125 to 200st 201 to 400st 140 118 98 21.5 38.5 58.5 80.5 81 140 118 98 15 32 52 74 81 161 134 114 21 42 62 89 93 161 134 114 16 37 57 84 93 A E 25 to 49st 50 to 74st 75 to 200st 201 to 400st 25 to 49st 50 to 74st 75 to 200st 201 to 400st 109.5 130 160 193 13 33.5 63.5 96.5 121 147 180 203 5 31 64 87 MGP Order Made Specifications Series Contact SMC for detailed specifications and lead times, and for applications of cylinders with air cushion, heavy duty guide rod type, and lock type. -XC19 2 With Air Cushion/Intermediate Strokes (Spacer Installed Type) M MGP L Bore size Stroke A XC19 With air cushion/Intermediate stroke The collar of of the standard stroke cylinder is changed to accommodate intermediate strokes in 1mm increments. CL Stroke range (mm) Bore size (mm) ø16 26 to 99 ø20 to ø63 26 to 199 ø80, ø100 51 to 199 MLG CNA ∗ Specifications and dimensions are the same as the standard products with air cushion. Intermediate strokes (in 1mm increments) with a special body are available by special order. CNG MNB -XB6 3 Heat Resistant Cylinder MGPM Bore size Stroke XB6 Specifications Heat resistant cylinder Cylinder with modified seal and grease materials to make possible high temperature operation up to an ambient temperature of 150°C. CB Slide bearing Bearing type Cylinder bore size (mm) CLS MGPM Applicable series CNS 12, 16, 20, 25, 32, 40, 50, 63, 80, 100 Ambient temperature range –10 to 150°C Seal material Fluoro rubber CV/MVG Heat resistant grease Grease None Cushion CXS Not applicable Auto switch CXW ∗ 1. Dimensions are the same as standard products. ∗ 2. Refer to page 3.22-60 for allowable kinetic energy. CXT MX -XB13 4 Low Speed Cylinder MGP ML Bore size Stroke XB13 MXH Specifications MGPM, MGPL Applicable series Low speed cylinder Bearing type Cylinder bore size (mm) Operates smoothly, without sticking and slipping, at drive speeds as low as 5 to 50mm/s. MXU Slide bearing, Ball bushing 12, 16, 20, 25, 32, 40, 50, 63, 80, 100 5 to 50mm/s Piston speed MXQ MXF Rubber bumper Cushion MXS ∗ Dimensions are the same as standard products. MXW MXP -XC22 5 Fluoro Rubber Seals MGPM Bore size Stroke XC22 Specifications Fluoro rubber seals Seals are changed to a fluoro rubber material which has outstanding resistance to chemicals. MGQ Slide bearing Bearing type Cylinder bore size (mm) MGP MGPM Applicable series MG 12, 16, 20, 25, 32, 40, 50, 63, 80, 100 Cushion Auto switch MGG None Mountable MGC ∗ 1. Dimensions are the same as standard products. ∗ 2. Refer to page 3.22-60 for allowable kinetic energy. MGF MGZ CY MY 3.22-57 MGP Order Made Specifications Series Contact SMC for detailed specifications and lead times, and for applications of cylinders with air cushion, heavy duty guide rod type, and lock type. -XC4 6 With Heavy Duty Scraper M MGP L Bore size XC4 Stroke Specifications Applicable series With heavy duty scraper Scraper specification Slide bearing, Ball bushing Cylinder bore size (mm) Single side scraper Double side scrapers Nil W MGPM, MGPL Bearing type With a heavy duty scraper used for the piston rod and guide rod sections, this specification is ideal for cylinders used in a dusty environment, or in environments where there is contact with earth and sand, such as molding machines, construction equipment, and industrial vehicles, etc. Furthermore, depending on the mounting orientation, the scraper on the plate side only (–XC4) or the double side scraper (–XC4W) can be selected. 20, 25, 32, 40, 50, 63, 80, 100 Single side Minimum operating pressure Double side 0.12MPa 0.14MPa ∗ Refer to the tables below for dimensions. -XC35 7 With Coil Scraper MGPM Bore size Specifications XC35 Stroke Bearing type Scraper specification Slide bearing Cylinder bore size (mm) Single side scraper Double side scraper Nil W MGPM Applicable series With coil scraper Removes frost, welding spatter, and machining chips from the piston rod and the guide rod, and protects the seals. Furthermore, depending on the mounting orientation, the scraper on the plate side only (–XC35) or the double side scraper (–XC35W) can be selected. 20, 25, 32, 40, 50, 63, 80, 100 Single side Minimum operating pressure Double side 0.12MPa 0.14MPa ∗ Refer to the tables below for dimensions. HT øDS 4-øMT With Heavy Duty Scraper/With Coil Scraper Common Dimensions FT FB B + Stroke A + Stroke EW + Stroke FT AW + 2 x Stroke E MGPM, MGPL Common dimensions (mm) With double side scrapers Dimensions AW, EW, MT, DS (mm) Bore size (mm) Bore size AW (mm) 20 25 32 40 50 63 80 100 B FB FT 63 63.5 69.5 76 82 87 106.5 126 16 16 20 20 22 22 28 35 5 5 6 6 6 6 6 9 20 25 32 40 50 63 80 100 EW 74 74.5 82.5 89 95 100 120.5 143 6 6 7 7 7 7 8 8 DS ∗ MGPM MGPL 17 15 6 21 19 7 21 8.5 26 26 21 9 31 26 11 31 26 11 36 31 14 44 36 16 The figure shows the heavy duty scraper (–XC4). Cylinders with coil scraper (–XC35) are without this lip. For cylinder with double side scraper MT MGPL (ball bushing)/Dimensions A, E, HT Bore size (mm) 20 25 A Over 30st Over 100st to 200st 30st or less to 100st 73 79.5 (mm) E 30st Over 100st Over 200st 30st or less Over to 200st Over 200st to 100st 132 114 90 95.5 114.5 132 10 16 51 51 27 32 69 68.5 HT 80 93 ∗ By-pass port size for guide rod with bottom mount MGPM (slide bearing)/Dimensions A, E, HT Bore size (mm) 20 25 32 40 50 63 80 100 3.22-58 A E 50st or less Over 50st to 200st 50st or less Over 50st to 200st 63 63.5 97 97 106.5 106.5 125 147 94.5 95 112 112 128 128 152 172 0 0 27.5 21 24.5 19.5 18.5 21 31.5 31.5 42.5 36 46 41 45.5 46 Over 200st 132 132 150 150 171 171 203 213 (mm) HT Over 200st XC4 XC35 69 80 80 68.5 93 93 80.5 113 110 74 121 118 89 153 146 84 167 160 96.5 205 200 87 244 238 Bore size (mm) 32 40 50 63 Bore size (mm) 80 100 A E Over 50st Over 100st to 200st 50st or less to 100st 91 91 103 103 108 108 124 124 128 128 144 144 Over 50st Over 100st to 200st Over 200st 50st or less to 100st 150 150 171 171 21.5 15 21 16 38.5 32 42 37 A 58.5 52 62 57 Over 200st 80.5 74 89 84 E 25st Over 50st Over 25st Over 50st 25st or less Over to 50st to 200st Over 200st to 200st Over 200st 25st or less to 50st 119.5 131 140 157 170 190 203 213 13 5 33.5 31 63.5 64 96.5 87 HT 110 118 146 160 HT 201 238 MGP Order Made Specifications Series Contact SMC for detailed specifications and lead times, and for applications of cylinders with air cushion, heavy duty guide rod type, and lock type. -XC8 8 Adjustable Stroke Cylinder/Adjustable Extension Type M MGP L Bore size A Stroke XC8 Specifications A B Slide bearing, Ball bushing Bearing type Stroke adjustment Piston speed Adjustable stroke cylinder Adjustable extension type ø12 to ø32 50 to 300mm/s ø40 to ø100 50 to 400mm/s A 10mm B 25mm Stroke adjustment The extended stroke of the cylinder can be adjusted 0 to 10mm or 0 to 25mm from the full stroke. Install a stroke adjustment mechanism at the head side to adjust the extended stroke. MB MC (Width across flats) MA MD MT MP ML + Adjustment Stroke MLG 12, 16, 20, 25, 32, 40, 50, 63, 80, 100 Cylinder bore size (mm) 10mm adjustment 25mm adjustment CL MGPM, MGPL Applicable series CNA CNG MNB CNS MGPM, MGPL Common dimensions Bore size (mm) 12 16 20 25 32 40 50 63 80 100 (mm) MA MB MC MD MH ML MP MT 28 29 34 40 52 60 68 84 114 140 16 19 30 30 38 38 50 50 50 65 14 14 22 22 27 27 36 36 46 46 M5 M5 M8 M8 M14 x 1.5 M14 x 1.5 M18 x 1.5 M18 x 1.5 M22 x 1.5 M22 x 1.5 22 22 30 30 37 37 47 47 58 62 9 9 12.5 12.5 16 16 20 20 28 28 3 3 3 3 4 4 4 4 4 4 5 5 8 8 8 8 9 9 12 16 CLS CB CV/MVG CXW CXS CXT MX MH + Stroke + Adjustment (A: 10mm, B: 25mm) MXU -XC9 9 Adjustable Stroke Cylinder/Adjustable Retraction Type MGP ML Bore size A Stroke XC9 Specifications MXS MGPM, MGPL Applicable series Slide bearing, Ball bushing Bearing type Stroke adjustment A B 12, 16, 20, 25, 32, 40, 50, 63, 80, 100 Cylinder bore size (mm) 10mm adjustment 25mm adjustment Piston speed Adjustable stroke cylinder Adjustable retraction type With an adjustment bolt, the retracted stroke of the cylinder can be adjusted 0 to 10mm or 0 to 25mm from the full stroke. (After the stroke adjustment, only the rod side is equipped with a rubber bumper.) Cushion Stroke adjustment MXH 50 to 300mm/s ø12 to ø32 ø40 to ø100 50 to 400mm/s Rod side Rubber bumper Head side None A 10mm B 25mm MXQ MXF MXW MXP MG ∗ Refer to page 3.22-60 for the allowable kinetic energy on the retracted side. MGP MB (Width across flats) øMC BM (Adjustment bolt) MA MH + Adjustment (A: 10mm, B: 25mm) MGPM, MGPL Common dimensions (mm) Bore size (mm) 12 16 20 25 32 40 50 63 80 100 BM MA MB MC MH M5 M6 M8 M8 M8 M12 x 1.5 M12 x 1.5 M16 x 1.5 M20 x 1.5 M24 x 1.5 5 5 6.5 6.5 6.5 9 9 10 15 18 8 10 13 13 19 27 30 36 41 46 12.5 11.5 16 16 21 30 34 40 46 52 19 19 27 26.5 26.5 33 32.5 37 53.5 57.5 MGQ MGG MGC MGF MGZ CY MY 3.22-59 MGP Order Made Specifications Series Contact SMC for detailed specifications and lead times, and for applications of cylinders with air cushion, heavy duty guide rod type, and lock type. -XC6 10 Stainless Steel Piston Rod, Plate, etc. M MGP L Bore size Stroke XC6 A 2. Guide rod Stainless steel specification A B 6. Snap ring 1. Piston rod Stainless steel material 3. Plate Stainless steel parts Stainless steel rod parts The materials used for some of the standard product parts are modified to stainless steel. XC6A XC6B Stainless steel modified parts 1, 2, 3, 4, 5, 6 1, 2, 5, 6 5. Hexagon socket head plug 4. Plate mounting bolt Allowable Kinetic Energy for Order Made Specifications (without Bumper) Some of the order made specification cylinders have a construction without internal bumpers. For the following order made products, refer to the graph for their overall load weight (load weight + weight of the moving parts of the cylinder) and piston speed at the stroke end. 500 400 300 ø100 200 ø80 Overall load weight (kg) Applicable order made products: Heat resistant cylinder (-XB6) Adjustable stroke cylinder/Adjustable retraction type (–XC9) Fluoro rubber seals (–XC22) 1000 100 ø63 ø50 50 40 ø40 30 ø32 20 ø25 10 ø20 5 ø16 4 3 ø12 2 1 0.1 100 200 300 400 Piston speed at the stroke end 3.22-60 500 υ (mm/s) 1000 MGP Order Made Specifications Series Contact SMC for detailed specifications and lead times, and for applications of cylinders with air cushion, heavy duty guide rod type, and lock type. -XC69 11 Compact Guide Cylinder with Shock Absorber Absorbs the impact at the extension stroke end. Extension adjusting mechanism using an adjusting screw. CL Stopper bracket Extension stroke adjustment • ø12 to ø25: 15mm • ø32 to ø63: 25mm • ø80, ø100: 30mm MLG CNA CNG Shock absorber Adjusting screw MNB End plate CNS How to Order 50 32 MGP M CLS Z73 CB XC69 CV/MVG With shock absorber Compact guide cylinder Bearing type CXW Number of auto switches M Slide bearing Nil 2 pcs. L Ball bushing S 1 pc. Bore size CXS CXT Auto switch type Nil 12 12mm 40 40mm 16 16mm 50 50mm 20 20mm 63 63mm 25 25mm 80 80mm Cylinder stroke (mm) 32 32mm 100 100mm Refer to the standard stroke table. Without auto switch (built-in magnet cylinder) MX ∗ Refer to the table below for auto switch model numbers. MXU MXH MXS Applicable auto switches Type Reed switch Special function — Electrical Indicator light entry Grommet Yes No — Solid state switch Diagnostic indication (2 colour indicator) Water resistant (2 colour indicator) Grommet Yes Load voltage Wiring (output) DC 3 wire — 2 wire 24V 3 wire (NPN) 3 wire (PNP) 2 wire 3 wire (NPN) 3 wire (PNP) 5V 12V AC — 100V Auto switch model Electrical entry direction Perpendicular In-line — Z76 Z73 — 5V, 12V 100V or less — Y69A 5V 12V Y7PV 12V Y69B Y7NWV 5V — 24V 12V Y7PWV Y7BWV 2 wire Magnetic field resistant (2 colour indicator) Note 1) Lead wire symbols 0.5m ....... Nil (Example) Y69B 3m .......... L Y69BL 5m .......... Z Y69BZ 12V — MXQ Lead wire length (m) 0.5 (Nil)   3 (L)   5 (Z) —  Z80 Y59A Y7P Y59B Y7NW Y7PW Y7BW Y7BAL        —         —        P5DW —   Applicable load IC circuit — IC circuit IC circuit IC circuit — IC circuit MXF — Relay, PLC MXW MXP Relay, PLC MG MGP — MGQ Note 2) Solid state auto switches marked with a "" are produced upon receipt of order. Note 3) Type P5DW is applicable only to bore sizes ø40 to ø100. MGG For a 25mm stroke, only one switch is mounted. MGC MGF MGZ CY MY 3.22-61 MGP Order Made Specifications Series Contact SMC for detailed specifications and lead times, and for applications of cylinders with air cushion, heavy duty guide rod type, and lock type. Extension Adjustment Mechanism Specifications Piston speed Cushion Note 2) Double acting Air 1.0MPa 1.5MPa 0.12MPa 0.10MPa –10 to 60°C Refer to the graphs on the right. Extended end Retracted end Shock absorber Rubber cushion Slide bearing, Ball bushing Bearing type Note 1) Excluding the cushion stroke generated by the shock absorber. Note 2) Operate at a piston speed that does not exceed the cylinder's allowable kinetic energy. Standard Strokes Model 12 MGP 16 M 20 MGP L 25 32 40 M 50 MGP L 63 80 100 M L Standard stroke (mm) 10, 20, 30, 40, 50, 75, 100, 125, 150, 175 200, 250 20, 30, 40, 50, 75, 100, 125, 150, 175, 200 250, 300, 350, 400 25, 50, 75, 100, 125, 150, 175, 200, 250 300, 350, 400 Bore size (mm) 20, 25 12, 16 RB0806 RB1007 Shock absorber model Max. absorbed energy (J) 2.94 5.88 Stroke adjustment range (mm) 0 to –15 32, 40 50, 63 RB1411 RB2015 58.8 19.6 0 to –25 80, 100 RB2725 147 0 to –30 Allowable Kinetic Energy Operate with a load weight and maximum speed within the ranges shown in the graph below. Retraction stroke end (rubber bumper) 300 Extension stroke end (shock absorber) 300 ø100 ø100 ø80 ø80 ø63 100 ø63 100 ø50 ø50 ø40 ø40 Load weight (kg) Action Fluid Maximum operating pressure Proof Pressure Note 1) ø12, ø16 Minimum operating pressure ø20 to ø100 Ambient and fluid temperature Load weight (kg) Specifications ø32 ø25 10 ø20 ø16 ø32 ø25 10 ø20 ø16 ø12 ø12 1 0.5 50 1 100 Maximum speed (mm/sec) 500 0.5 50 100 500 Maximum speed (mm/sec) Note 1) Intermediate strokes (in 5mm increments) are produced by installing spacers of 5, 10, 15 and 20mm widths. The overall length (A + stroke x 2) and the guide rod length (E + stroke) shown in the dimensions section do not include the spacer widths. Contact SMC when a special intermediate stroke body is needed. Specific Product Precautions Be sure to read before handling. Consult SMC when outside the specifications. Mounting Stopper bracket Warning Hexagon nut 1 Hexagon nut 2 Do not put hands or fingers, etc., near the cylinder during operation. If fingers, etc., are caught in the space between the shock absorber and body, human injury and damage to nearby equipment may occur. Implement protective measures such as mounting of protective covers as needed. Shock absorber Caution Adjusting screw As a rule, do not bottom mount the cylinder. Mounting space is limited at the bottom of the cylinder due to the guide rod and end plate. Use the top or side mount method to mount the cylinder. Adjustment End plate ∗ Adjust so that the end of the adjusting screw makes direct contact with the stopper bracket. Caution 1. Adjusting screw adjustment (stroke adjustment) To make a stroke adjustment, loosen only hexagon nut 1 and rotate the adjusting screw. After adjusting, lock the adjustment with hexagon nut 1. To put the end of the adjusting screw in direct contact with the stopper bracket, fix the adjusting screw at a position where its end protrudes from the end plate. (Refer to the figure on the top right.) Shock absorber 2. Shock absorber replacement Loosen hexagon nut 2, then rotate the shock absorber counter clockwise and remove it. When mounting a new shock absorber, the end of the adjusting screw must protrude approximately 0.5mm from the shock absorber. (Refer to the figure on the right.) When the shock absorber position is adjusted, be sure to lock it with hexagon nut 2. 3.22-62 Adjusting screw 0.5mm MGP Order Made Specifications Series Contact SMC for detailed specifications and lead times, and for applications of cylinders with air cushion, heavy duty guide rod type, and lock type. ø12 to ø63 Dimensions/ Z WA WB CL øXAH7 depth XL (mm) a b X±0.02 X XB øXAH7 Bore size XAH7 XC c d e XL T -slot dimensions Section XX detail (mm) a b c d e 12 16 20 25 32 40 50 63 4.4 4.4 5.4 5.4 6.5 6.5 8.5 11 7.4 7.4 8.4 8.4 10.5 10.5 13.5 17.8 3.7 3.7 4.5 4.5 5.5 5.5 7.5 10 2 2.5 2.8 3 3.5 4 4.5 7 6.2 6.7 7.8 8.2 9.5 11 13.5 18.5 Section XX CNG MNB CNS 4-øOA through 4-MM depth ML Z Section XX 4-NN through 4-øOB counter bore depth OL WA CB RR CV/MVG RB CXS T R X U øDA X±0.02 CXW PW CXT MX øDB HA: T-slot for hexagon bolt VB VA MA H CNA CLS 4-YY depth YL MB L MLG MXU 2-P PB (Plug) FA FB K C + Stroke B + Stroke G MXH MT GB PA + Stroke J øXAH7 depth XL 2-P GC GA MC E + Stroke Q S (RA) MXS A + Stroke x 2 Bore size (mm) 12 16 20 25 32 40 50 63 Standard stroke (mm) A B C DA 10, 20, 30, 40, 50, 75, 100, 125, 150, 175, 200, 250 20, 30, 40, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400 90 94 109 109.5 135.5 142 155 160 42 46 53 53.5 59.5 66 72 77 29 33 37 37.5 37.5 44 44 49 6 8 10 12 16 16 20 20 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400 DB Slide bearing Ball bushing 8 10 12 16 20 20 25 25 6 8 10 13 16 16 20 20 FA FB E 7 7 9 9 9 9 10 10 8 8 10 10 12 12 16 16 5 5 6 6 10 10 12 12 (mm) G GA GB GC 26 30 36 42 48 54 64 78 7.5 11 8 11 10.5 8.5 11.5 9 12.5 9 14 10 14 11 16.5 13.5 11 11 10.5 11.5 12.5 14 12 16.5 HA J K 58 M4 64 M4 83 M5 93 M5 112 M6 120 M6 148 M8 162 M10 13 15 18 21 24 27 32 39 13 15 18 21 24 27 32 39 H L MA MB MC MT 18 22 24 30 34 40 46 58 51 58 68 82 100 108 139 153 19 19 30 30 38 38 60 60 8 8 10 10 12 12 16 16 MM M4 M5 M5 M6 M8 M8 M10 M10 6 6 8 8 8 8 9 9 (mm) Bore size (mm) ML NN OA OB OL 12 16 20 25 32 40 50 63 10 12 13 15 20 20 22 22 M4 M5 M5 M6 M8 M8 M10 M10 4.3 4.3 5.6 5.6 6.6 6.6 8.6 8.6 8 8 9.5 9.5 11 11 14 14 4.5 4.5 5.5 5.5 7.5 7.5 9 9 P M5 M5 Rc 1/8 Rc 1/8 Rc 1/8 Rc 1/8 Rc 1/4 Rc 1/4 PA PB PW Q 13 15 12.5 12.5 7 13 9 14 8 10 10.5 13.5 15 18 21.5 28 18 19 25 28.5 34 38 47 55 14 16 18 26 30 30 40 50 RA RB RR S T VA VB X 48 54 70 78 96 104 130 130 33 33 37 37 55 55 57 57 RB0806 RB0806 RB1007 RB1007 RB1412 RB1412 RB2015 RB2015 M12 x 1.5 M12 x 1.5 M14 x 1.5 M14 x 1.5 M20 x 1.5 M20 x 1.5 M27 x 1.5 M27 x 1.5 22 25 30 38 44 44 60 70 56 41 50 37 62 46 56 38 81 54 72 44 91 64 82 50 110 78 98 63 72 118 86 106 92 146 110 130 158 124 142 110 23 24 28 34 42 50 66 80 MGP12 to 25/WA, WB Dimensions (mm) (mm) 30 stroke or less 12 16 20 25 20 24 24 24 110 110 120 120 200 200 200 200 300 300 15 17 29 29 25 27 39 39 60 60 77 77 3 3 3 4 4 4 5 5 3.5 3.5 3.5 4.5 4.5 4.5 6 6 3 3 3 3 3 3 4 4 6 6 6 6 6 6 8 8 105 105 117 117 167 167 YY YL Z M5 M5 M6 M6 M8 M8 M10 M10 10 10 12 12 16 16 20 20 5 5 17 17 21 22 24 24 Bore size (mm) 32 40 50 63 MXF MXW MXP MG MGP MGQ MGG MGC (mm) MGF Over Over Over Over Over Over 25 stroke 25 stroke 100 stroke 200 stroke Over 25 stroke 25 stroke 100 stroke 200 stroke Over or less to 300 stroke to to to to to 300 stroke or less 100 stroke 200 stroke 300 stroke 100 stroke 200 stroke 300 stroke MGZ WA Over Over Over Over Over Over Over 30 stroke 100 stroke 200 stroke Over 30 stroke 30 stroke 100 stroke 200 stroke to to to to to to 300 stroke 300 stroke or less 100 stroke 200 stroke 300 stroke 100 stroke 200 stroke 300 stroke 40 44 44 44 XA XB XC XL MGP32 to 63/WA, WB Dimensions WB WA Bore size U R MXQ 24 24 24 28 48 48 48 52 124 124 124 128 WB 200 200 200 200 300 300 300 300 33 34 36 38 45 46 48 50 83 84 86 88 121 122 124 124 171 172 174 174 3.22-63 CY MY MGP Order Made Specifications Series ø80, ø100 Dimensions/ Z WB WA ø6H7 depth 10 (mm) Bore size a (mm) 80 100 b c d e a b X±0.02 6H7 X 7 ø6H7 8 22.5 13.3 20.3 12 15.3 23.3 13.5 10 30 5 c d e 10 Section XX detail T-slot dimensions 4-YY depth YL Section XX 75 L 4-MM depth ML 4-øOA through 4-NN through 4-øOB counter bore depth 8 WA Z Section XX X±0.02 T R PW X U øDA øDB HA: T-slot for hexagon bolt VB VA MA H M36 x 1.5 RB2725 2-Rc 3/8 PB 10 JA J (plug) JB ø6H7 depth 10 GC GA 2-Rc 3/8 16 GB PA + Stroke C + Stroke FA FB K 17 + Stroke MC B + Stroke G Q S (RA) A + Stroke x 2 (mm) Bore size (mm) 80 100 DB Standard stroke 25, 50, 75, 100 125, 150, 175, 200 250, 300, 350, 400 B A (mm) C DA Slide Ball FA FB bearing bushing G GA GB GC 30 25 22 18 232 116 36 30 25 25 111.5 23 19 30 HA J JA JB 18 K L MA MC MM ML NN OA 7.5 46 54 190 22 M12 25 M12 10.6 240 M14 55.5 45 10.5 56 62 228 25 M14 31 M14 12.5 91.5 19 15.5 14.5 202 M12 45.5 38 212.5 96.5 56.5 25 66 H (mm) WB WA Bore size OB PA PB PW Q (mm) 80 100 R RA S T U VA VB 25 stroke Over Over Over Over Over Over 25 stroke 100 stroke 200 stroke Over 25 stroke 100 stroke 200 stroke Over to to to to to to 300 stroke 300 stroke 25 stroke 100 stroke 200 stroke 300 stroke 100 stroke 200 stroke 300 stroke X YY YL Z 17.5 14.5 25.5 74 52 174 77 75 198 156 180 140 28 52 128 200 300 42 54 92 128 178 100 M12 24 28 17.5 32.5 89 64 210 74 90 236 188 210 166 48 72 148 220 320 35 47 85 121 171 124 M14 28 11 20 3.22-64 MGP Specific Product Precautions Series Mounting Cushion Warning When equipped with air cushion 1. Do not put hands or fingers, etc. between the plate and body. Be careful that hands or fingers, etc., do not get caught in the space between the cylinder body and the plate when air pressure is applied. Caution CL 1. Keep the adjustment range MLG of the cushion valve within 3 rotations of the completely CNA closed position. When adjusting the cushion valve, use the following screw driver or hexagon wrenches. Keep the adjustment range of the cushion valve within 3 rotations of the completely closed position. Air leakage will occur if operated after opening by 4 rotations or more. Furthermore, a stopper mechanism is provided for the cushion valve, and it should not be forced open beyond that position. Caution 1. Do not scratch or nick the sliding parts of the piston rod and guide rods. 2. Bottom of cylinder. The guide rods protrude from the bottom of the cylinder at the end of the retracting stroke, and therefore, in cases where the cylinder is to be bottom mounted, it is necessary to provide by-pass ports in the mounting surface for the guide rods, as well as holes for the hexagon socket head screws which are used for mounting. Moreover, in applications where impact occurs from a stopper, etc., the mounting bolts should be inserted to a depth of 2d or more (1.5d or more for MGPS). Series MGPS øD By-pass port dia. øD By-pass port dia. C ±0.2 B ±0.2 B ±0.2 C ±0.2 16 Flat head watchmakers screw driver 3mm 1.5d or more (d = Thread O.D.) (d = Thread O.D.) 80, 100 2. Be sure to activate the air cushion at the cylinder stroke end. Be sure to activate the air cushion at the end of the cylinder stroke. When it is intended to operate with the cushion valve fully opened, select a cylinder equipped with rubber bumper. If operated without confirming this point, the piston rod assembly, etc., may be damaged. Piping Hexagon socket Bore size A B C D (mm) (mm) (mm) (mm) (mm) mounting bolt 50 80 140 214 50 66 116 170 32 47 M12 M16 CNS CLS CB CV/MVG CXW CXS CXT MX MXU MXH 3. Be sure to operate a cylinder equipped with air cushion to MXS the end of the stroke. MXQ MXF MXW MXP MG Caution D (mm) Hexagon socket Bore size A B C (mm) (mm) (mm) (mm) MGPM MGPL mounting bolt 50 18 41 10 8 M4 12 56 22 46 12 10 M5 16 72 24 54 14 12 M5 20 82 30 64 18 15 M6 25 98 34 78 22 18 M8 32 106 40 86 22 18 M8 40 130 46 110 27 22 M10 50 142 58 124 27 22 M10 63 180 54 156 33 28 M12 80 210 62 188 39 33 M14 100 MNB JIS B4648 hexagon wrench key 4 If it is not operated to the end of the stroke, the effect of the air cushion will not be fully exhibited. Consequently, in cases where the stroke is regulated by an external stopper, etc., caution must be exercised, as the air cushion may become completely ineffective. A ±0.2 A ±0.2 2d or more Applicable tool 20, 25, 32, 40 JIS B4648 hexagon wrench key 1.5 50, 63 JIS B4648 hexagon wrench key 2.5 Damage to seals can cause air leaks or malfunction, etc. Series MGP Bore size (mm) CNG Depending on the operating conditions, piping port positions can be changed by using a plug. MGP MGQ MGG 1. For M5 After tightening by hand, tighten an extra 1/6 to 1/4 rotation with a tightening tool. 2. For taper thread Use the correct tightening torques listed below. Before tightening the plug, wrap pipe tape around it. Connection thread size Correct tightening torque N·m 7 to 9 R 1/8 12 to 14 R 1/4 22 to 24 R 3/8 3.22-65 MGC MGF MGZ CY MY MGP Specific Product Precautions Series Operating Pressure Use the recommended pneumatic circuits. Caution Caution • This is necessary for proper operation and release of the lock. 1. Use air pressure of at least 0.15MPa for the port on the lock mechanism side. This is necessary to release the lock. Exhaust Speed Caution 1. Locking will occur automatically if the pressure applied to the port on the lock mechanism side falls to 0.05MPa or less. In cases where the piping on the lock mechanism side is long and thin, or the speed controller is separated at some distance from the cylinder port, the exhaust speed will be reduced. Take note that some time may be required for the lock to engage. In addition, clogging of a silencer mounted on the solenoid valve exhaust port can produce the same effect. With rear lock With front lock Releasing the Lock Operation Caution 1. Do not use 3 position solenoid valves. Avoid use in combination with 3 position solenoid valves (especially closed centre metal seal types). If pressure is trapped in the port on the lock mechanism side, the cylinder cannot be locked. Furthermore, even after being locked, the lock may be released after some time, due to air leaking from the solenoid valve and entering the cylinder. 2. Back pressure is required when releasing the lock. Before starting operation, be sure to control the system so that air is supplied to the side without the lock mechanism as shown in the figure above. There is a possibility that the lock may not be released. (Refer to the section on releasing the lock.) 3. Release the lock when mounting or adjusting the cylinder. If mounting or other work is performed when the cylinder is locked, the lock unit may be damaged. 4. Operate with a load ratio of 50% or less. If the load ratio exceeds 50%, this may cause problems such as failure of the lock to release, or damage to the lock unit. Furthermore, do not exceed the operating ranges indicated in the series MGP catalog (Best Pneumatics No. 2) when making selections. 5. Do not operate multiple synchronized cylinders. Avoid applications in which two or more end lock cylinders are synchronized to move one workpiece, as one of the cylinder locks may not be able to release when required. 6. Use a speed controller with the meter-out function. It may not be possible to release the lock with meter-in control. 7. Be sure to operate completely to the cylinder stroke end on the side with the lock. If the cylinder piston does not reach the end of the stroke, locking and unlocking may not be possible. 8. Do not use an air cylinder as an air-hydro cylinder. This will cause leakage of hydraulic fluid. 9. Adjust an auto switch's position so that it operates for movement to both the stroke and backlash (2mm) positions. A 2 colour indication switch adjusted for green indication at the stroke end may change to red indication after the backlash return, but this is not abnormal. 3.22-66 Warning 1. Before releasing the lock, be sure to supply air to the side without the lock mechanism, so that there is no load applied to the lock mechanism when it is released. (Refer to the recommended pneumatic circuits.) If the lock is released when the port on the other side is in an exhaust state, and with a load applied to the lock unit, the lock unit may be subjected to an excessive force and be damaged. Furthermore, sudden movement of the piston rod is very dangerous. Manual Release Caution 1. Non-locking type manual release Insert the accessory bolt from the top of the rubber cap (it is not necessary to remove the rubber cap), and after screwing it into the lock piston, pull it to release the lock. If you stop pulling the bolt, the lock will return to an operational state. Thread sizes, pulling forces and strokes are as shown below. Bore size (mm) 20, 25, 32 M2.5 x 25l or more 4.9N 2 40, 50, 63 M3 x 30l or more 10N 3 80, 100 M5 x 40l or more 24.5N 3 Thread size Pulling force N Stroke (mm) ∗ Remove the bolt for normal operation. It can cause lock malfunction or faulty release. 2. Locking type manual release While pushing the M/O knob turn it 90° counter clockwise. The lock is released (and remains in a released state) by aligning the  mark on the cap with the  OFF mark on the M/O knob. To operate the lock, turn the M/O knob 90° clockwise while pushing it all the way Release Lock down, and align the  mark on the cap with the  ON mark on the M/O knob. When doing this, be sure that it locks into place with a click. Failure to click into place properly, can cause the lock to Locked condition Released condition disengage.