Transcript
ORDERING MIC-35T/*/36C/# Miniature interface converter, V.35 DTE to V.36 DCE *
Specify DTE side interface connector type: F for female connector (Default is male connector)
# Specify DCE side interface connector type: F for female connector (Default is male connector)
www.rad.com International Headquarters U.S. Headquarters 24 Raoul Wallenberg Street 900 Corporate Drive Tel Aviv 69719, Israel Mahwah, NJ 07430 Tel: (972) 3-6458181 Tel: (201) 529-1100 Fax: (972) 3-6498250, 6474436 Toll free: 1-800-444-7234 Email:
[email protected] Fax: (201) 529-5777 Email:
[email protected]
250-250-12/04 Specifications are subject to change without prior notice. 1989 – 2004 RAD Data Communications Ltd.
MIC-35T/36C Miniature Interface Converter, V.35 DTE to V.36 DCE
FEATURES
• Converts between V.35 DTE and V.36 (RS-449/422) DCE
• Operates at data rates of up to 2048 kbps
• • • •
Transparent to protocol No external power required Easy to install Miniature, lightweight
DESCRIPTION • MIC-35T/36C miniature interface converter, converts between DTEs with the V.35 interface and DCEs with the V.36 (RS-449/422) interface at data rates of up to 2048 kbps (see Figure 1 for the data flow diagram).
• MIC-35T/36C performs both physical and electrical conversion between the two interfaces. The circuitry is designed to provide short range interface, i.e. for connection of co-located devices.
• No AC power is required. The device uses
ultra-low power derived from the DTE and DCE data and control signals.
APPLICATION
SPECIFICATIONS • Data Rates
Up to 2048 kbps
• Transmission Format
Synchronous (transparent to protocol)
• Interface Connectors DTE: DCE:
V.35, 34-pin, male/female V.36 (RS-449/422), 37-pin, male/female (see Ordering)
• Cable Length 2m (6.5 ft)
• Power
No AC power required; uses ultra-low power derived from the DTE and DCE data and control signals
• Physical
Length: 110 mm / 4.3 in Width: 53 mm / 2.1 in Height: 22 mm / 0.9 in Weight: 220g / 7.7 oz (including cable and connector)
• Environment
Temperature: 0–50°C / 32–122°F Humidity: Up to 90%, non-condensing
V.35 (DTE) Male/Female B
Signal GND RTS
CTS
DSR
DTR
DCD
C
D
E
H
F
V.36 (DCE) Male/Female 37, 20, 19
Signal GND
7
RS-a
25
RS-b
9
CS-a
27
CS-b
11
DM-a
29
DM-b
12
TR-a
30
TR-b
13
RR-a
31
RR-b
5
TC-a
Y
TC-b
AA
RC-a
V
8
RC-b
X
26
TD-a
P
4
SD-a
S
22
SD-b
TD-b
23
ST-a ST-b RT-a RT-b
RD-a
R
6
RD-b
T
24
RD-b
EC-a
U
17
TT-a
EC-b
W
35
TT-b
INSTALLATION Installation of MIC-35T/36C is straightforward and simple, no internal settings are required.
Declaration of Conformity Mfr. Name: RAD Data Communications Ltd.
Proceed as follows:
Mfr. Address: 24 Raoul Wallenberg St. Tel Aviv, 69719, Israel
1. Plug the V.35 connector directly into the DTE.
declares that the product: MIC-35T/36C
2. Plug the V.36 connector directly into the DCE. MIC-35T/36C is ready to operate.
Conforms to the following standard(s) or other normative document(s): EMC:
EN 55022 (1994): Limits and methods of measurement of radio disturbance characteristics of information technology equipment. EN 50082-1 (1992): Electromagnetic compatibility - Generic immunity standards for residential, commercial and light industry.
Supplementary Information: The product herewith complies with the requirements of the EMC Directive 89/336/EEC. The product was tested in a typical configuration.
RD-a
Figure 1. Data Flow through MIC-35T/36C
Tel Aviv, July 23rd, 1996 Haim Karshen VP Quality European Contact: RAD Data Communications GmbH, Otto-Hahn-Str. 28-30, 85521 Ottobrunn-Riemerling
